From: Emil Renner Berthing <emil.renner.berthing@canonical.com>
To: linux-riscv@lists.infradead.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org
Cc: Paul Walmsley <paul.walmsley@sifive.com>,
Palmer Dabbelt <palmer@dabbelt.com>,
Emil Renner Berthing <kernel@esmil.dk>,
Conor Dooley <conor@kernel.org>, Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
Cristian Ciocaltea <cristian.ciocaltea@collabora.com>,
Geert Uytterhoeven <geert@linux-m68k.org>
Subject: [PATCH v2 7/8] riscv: dts: starfive: Enable SD-card on JH7100 boards
Date: Thu, 30 Nov 2023 16:19:31 +0100 [thread overview]
Message-ID: <20231130151932.729708-8-emil.renner.berthing@canonical.com> (raw)
In-Reply-To: <20231130151932.729708-1-emil.renner.berthing@canonical.com>
Add pinctrl and MMC device tree nodes for the SD-card on the
BeagleV Starlight and StarFive VisionFive V1 boards.
Signed-off-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
---
.../boot/dts/starfive/jh7100-common.dtsi | 47 +++++++++++++++++++
1 file changed, 47 insertions(+)
diff --git a/arch/riscv/boot/dts/starfive/jh7100-common.dtsi b/arch/riscv/boot/dts/starfive/jh7100-common.dtsi
index 3af88e6970a3..adcdbbc4f57f 100644
--- a/arch/riscv/boot/dts/starfive/jh7100-common.dtsi
+++ b/arch/riscv/boot/dts/starfive/jh7100-common.dtsi
@@ -12,6 +12,7 @@
/ {
aliases {
+ mmc0 = &sdio0;
serial0 = &uart3;
};
@@ -108,6 +109,43 @@ GPO_I2C2_PAD_SDA_OEN,
};
};
+ sdio0_pins: sdio0-0 {
+ clk-pins {
+ pinmux = <GPIOMUX(54, GPO_SDIO0_PAD_CCLK_OUT,
+ GPO_ENABLE, GPI_NONE)>;
+ bias-disable;
+ input-disable;
+ input-schmitt-disable;
+ };
+ sdio-pins {
+ pinmux = <GPIOMUX(55, GPO_LOW, GPO_DISABLE,
+ GPI_SDIO0_PAD_CARD_DETECT_N)>,
+ <GPIOMUX(53,
+ GPO_SDIO0_PAD_CCMD_OUT,
+ GPO_SDIO0_PAD_CCMD_OEN,
+ GPI_SDIO0_PAD_CCMD_IN)>,
+ <GPIOMUX(49,
+ GPO_SDIO0_PAD_CDATA_OUT_BIT0,
+ GPO_SDIO0_PAD_CDATA_OEN_BIT0,
+ GPI_SDIO0_PAD_CDATA_IN_BIT0)>,
+ <GPIOMUX(50,
+ GPO_SDIO0_PAD_CDATA_OUT_BIT1,
+ GPO_SDIO0_PAD_CDATA_OEN_BIT1,
+ GPI_SDIO0_PAD_CDATA_IN_BIT1)>,
+ <GPIOMUX(51,
+ GPO_SDIO0_PAD_CDATA_OUT_BIT2,
+ GPO_SDIO0_PAD_CDATA_OEN_BIT2,
+ GPI_SDIO0_PAD_CDATA_IN_BIT2)>,
+ <GPIOMUX(52,
+ GPO_SDIO0_PAD_CDATA_OUT_BIT3,
+ GPO_SDIO0_PAD_CDATA_OEN_BIT3,
+ GPI_SDIO0_PAD_CDATA_IN_BIT3)>;
+ bias-pull-up;
+ input-enable;
+ input-schmitt-enable;
+ };
+ };
+
uart3_pins: uart3-0 {
rx-pins {
pinmux = <GPIOMUX(13, GPO_LOW, GPO_DISABLE,
@@ -178,6 +216,15 @@ &osc_aud {
clock-frequency = <27000000>;
};
+&sdio0 {
+ broken-cd;
+ bus-width = <4>;
+ cap-sd-highspeed;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdio0_pins>;
+ status = "okay";
+};
+
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&uart3_pins>;
--
2.40.1
next prev parent reply other threads:[~2023-11-30 15:20 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-11-30 15:19 [PATCH v2 0/8] Add JH7100 errata and update device tree Emil Renner Berthing
2023-11-30 15:19 ` [PATCH v2 1/8] riscv: errata: Add StarFive JH7100 errata Emil Renner Berthing
2023-12-06 17:09 ` Palmer Dabbelt
2023-11-30 15:19 ` [PATCH v2 2/8] riscv: dts: starfive: Group tuples in interrupt properties Emil Renner Berthing
2023-11-30 15:19 ` [PATCH v2 3/8] riscv: dts: starfive: Mark the JH7100 as having non-coherent DMAs Emil Renner Berthing
2023-11-30 15:19 ` [PATCH v2 4/8] riscv: dts: starfive: Add JH7100 cache controller Emil Renner Berthing
2023-11-30 15:19 ` [PATCH v2 5/8] riscv: dts: starfive: Add pool for coherent DMA memory on JH7100 boards Emil Renner Berthing
2023-11-30 15:19 ` [PATCH v2 6/8] riscv: dts: starfive: Add JH7100 MMC nodes Emil Renner Berthing
2023-11-30 15:19 ` Emil Renner Berthing [this message]
2023-11-30 15:19 ` [PATCH v2 8/8] riscv: dts: starfive: Enable SDIO wifi on JH7100 boards Emil Renner Berthing
2023-12-13 15:42 ` (subset) [PATCH v2 0/8] Add JH7100 errata and update device tree Conor Dooley
2023-12-13 15:51 ` Geert Uytterhoeven
2023-12-15 19:13 ` Emil Renner Berthing
2023-12-13 15:53 ` Conor Dooley
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20231130151932.729708-8-emil.renner.berthing@canonical.com \
--to=emil.renner.berthing@canonical.com \
--cc=conor@kernel.org \
--cc=cristian.ciocaltea@collabora.com \
--cc=devicetree@vger.kernel.org \
--cc=geert@linux-m68k.org \
--cc=kernel@esmil.dk \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-riscv@lists.infradead.org \
--cc=palmer@dabbelt.com \
--cc=paul.walmsley@sifive.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox