[PATCH v6 00/11] soc: qcom: spm: add support for SPM regulator

[PATCH v6 00/11] soc: qcom: spm: add support for SPM regulator

[Dmitry Baryshkov]

The apq8064 rework to use cacheinfo takes more than expected, so I've
spanwed this series. It is an excerpt of the APQ8064 cpufreq series
[1], so it it continues the version numbering for those patches.

The Subsystem Power Manager (SPM) / SPM AutoVoltageScaling Wrapper2
(SAW2) are hardware blocks used on some of Qualcomm platforms to handle
the voltage rails. It does this by bypassing RPM and directly
interfacing the PMIC. Extend current SPM driver to export this
regulator.

[1] https://lore.kernel.org/linux-arm-msm/20230827115033.935089-1-dmitry.baryshkov@linaro.org/

Changes since v5:
- Added patch that moves SPM structs out of the header file
- Removed support for L2 SAW regulator (Stephan Gerhold).
  msm8960/apq8064 do not use this SAW2 to manage this regulator and
  other platforms will need changes anyway.

Dmitry Baryshkov (11):
  dt-bindings: soc: qcom: merge qcom,saw2.txt into qcom,spm.yaml
  dt-bindings: soc: qcom: qcom,saw2: define optional regulator node
  soc: qcom: spm: remove driver-internal structures from the driver API
  soc: qcom: spm: add support for voltage regulator
  ARM: dts: qcom: apq8064: rename SAW nodes to power-manager
  ARM: dts: qcom: apq8064: declare SAW2 regulators
  ARM: dts: qcom: msm8960: declare SAW2 regulators
  ARM: dts: qcom: apq8084: drop 'regulator' property from SAW2 device
  ARM: dts: qcom: msm8974: drop 'regulator' property from SAW2 device
  ARM: dts: qcom: ipq4019: drop 'regulator' property from SAW2 devices
  ARM: dts: qcom: ipq8064: drop 'regulator' property from SAW2 devices

 .../devicetree/bindings/arm/msm/qcom,saw2.txt |  58 ----
 .../qcom/{qcom,spm.yaml => qcom,saw2.yaml}    |  39 ++-
 arch/arm/boot/dts/qcom/qcom-apq8064.dtsi      |  32 ++-
 arch/arm/boot/dts/qcom/qcom-apq8084.dtsi      |   1 -
 arch/arm/boot/dts/qcom/qcom-ipq4019.dtsi      |   5 -
 arch/arm/boot/dts/qcom/qcom-ipq8064.dtsi      |   2 -
 arch/arm/boot/dts/qcom/qcom-msm8960.dtsi      |  12 +-
 arch/arm/boot/dts/qcom/qcom-msm8974.dtsi      |   1 -
 drivers/soc/qcom/spm.c                        | 254 +++++++++++++++++-
 include/soc/qcom/spm.h                        |  23 +-
 10 files changed, 317 insertions(+), 110 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/arm/msm/qcom,saw2.txt
 rename Documentation/devicetree/bindings/soc/qcom/{qcom,spm.yaml => qcom,saw2.yaml} (57%)

-- 
2.39.2

[PATCH v6 01/11] dt-bindings: soc: qcom: merge qcom,saw2.txt into qcom,spm.yaml

[Dmitry Baryshkov]

The Qualcomm SPM / SAW2 device is described in two bindigns files:
arm/msm/qcom,saw2.txt and soc/qcom/qcom,spm.yaml. Merge the former into
the latter, adding detailed device node description. While we are at it,
also rename qcom,spm.yaml to qcom,saw2.yaml to follow the actual
compatible used for these devices.

The regulator property is retained as is. It will be changed in the
later patches.

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 .../devicetree/bindings/arm/msm/qcom,saw2.txt | 58 -------------------
 .../qcom/{qcom,spm.yaml => qcom,saw2.yaml}    | 26 +++++++--
 2 files changed, 20 insertions(+), 64 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/arm/msm/qcom,saw2.txt
 rename Documentation/devicetree/bindings/soc/qcom/{qcom,spm.yaml => qcom,saw2.yaml} (64%)

diff --git a/Documentation/devicetree/bindings/arm/msm/qcom,saw2.txt b/Documentation/devicetree/bindings/arm/msm/qcom,saw2.txt
deleted file mode 100644
index c0e3c3a42bea..000000000000
--- a/Documentation/devicetree/bindings/arm/msm/qcom,saw2.txt
+++ /dev/null
@@ -1,58 +0,0 @@
-SPM AVS Wrapper 2 (SAW2)
-
-The SAW2 is a wrapper around the Subsystem Power Manager (SPM) and the
-Adaptive Voltage Scaling (AVS) hardware. The SPM is a programmable
-power-controller that transitions a piece of hardware (like a processor or
-subsystem) into and out of low power modes via a direct connection to
-the PMIC. It can also be wired up to interact with other processors in the
-system, notifying them when a low power state is entered or exited.
-
-Multiple revisions of the SAW hardware are supported using these Device Nodes.
-SAW2 revisions differ in the register offset and configuration data. Also, the
-same revision of the SAW in different SoCs may have different configuration
-data due the differences in hardware capabilities. Hence the SoC name, the
-version of the SAW hardware in that SoC and the distinction between cpu (big
-or Little) or cache, may be needed to uniquely identify the SAW register
-configuration and initialization data. The compatible string is used to
-indicate this parameter.
-
-PROPERTIES
-
-- compatible:
-	Usage: required
-	Value type: <string>
-	Definition: Must have
-			"qcom,saw2"
-		    A more specific value could be one of:
-			"qcom,apq8064-saw2-v1.1-cpu"
-			"qcom,msm8226-saw2-v2.1-cpu"
-			"qcom,msm8974-saw2-v2.1-cpu"
-			"qcom,apq8084-saw2-v2.1-cpu"
-
-- reg:
-	Usage: required
-	Value type: <prop-encoded-array>
-	Definition: the first element specifies the base address and size of
-		    the register region. An optional second element specifies
-		    the base address and size of the alias register region.
-
-- regulator:
-	Usage: optional
-	Value type: boolean
-	Definition: Indicates that this SPM device acts as a regulator device
-			device for the core (CPU or Cache) the SPM is attached
-			to.
-
-Example 1:
-
-	power-controller@2099000 {
-		compatible = "qcom,saw2";
-		reg = <0x02099000 0x1000>, <0x02009000 0x1000>;
-		regulator;
-	};
-
-Example 2:
-	saw0: power-controller@f9089000 {
-		compatible = "qcom,apq8084-saw2-v2.1-cpu", "qcom,saw2";
-		reg = <0xf9089000 0x1000>, <0xf9009000 0x1000>;
-	};
diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,spm.yaml b/Documentation/devicetree/bindings/soc/qcom/qcom,saw2.yaml
similarity index 64%
rename from Documentation/devicetree/bindings/soc/qcom/qcom,spm.yaml
rename to Documentation/devicetree/bindings/soc/qcom/qcom,saw2.yaml
index 20c8cd38ff0d..84b3f01d590c 100644
--- a/Documentation/devicetree/bindings/soc/qcom/qcom,spm.yaml
+++ b/Documentation/devicetree/bindings/soc/qcom/qcom,saw2.yaml
@@ -1,18 +1,25 @@
 # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
 %YAML 1.2
 ---
-$id: http://devicetree.org/schemas/soc/qcom/qcom,spm.yaml#
+$id: http://devicetree.org/schemas/soc/qcom/qcom,saw2.yaml#
 $schema: http://devicetree.org/meta-schemas/core.yaml#
 
-title: Qualcomm Subsystem Power Manager
+title: Qualcomm Subsystem Power Manager / SPM AVS Wrapper 2 (SAW2)
 
 maintainers:
   - Andy Gross <agross@kernel.org>
   - Bjorn Andersson <bjorn.andersson@linaro.org>
 
 description: |
-  This binding describes the Qualcomm Subsystem Power Manager, used to control
-  the peripheral logic surrounding the application cores in Qualcomm platforms.
+  The Qualcomm Subsystem Power Manager is used to control the peripheral logic
+  surrounding the application cores in Qualcomm platforms.
+
+  The SAW2 is a wrapper around the Subsystem Power Manager (SPM) and the
+  Adaptive Voltage Scaling (AVS) hardware. The SPM is a programmable
+  power-controller that transitions a piece of hardware (like a processor or
+  subsystem) into and out of low power modes via a direct connection to
+  the PMIC. It can also be wired up to interact with other processors in the
+  system, notifying them when a low power state is entered or exited.
 
 properties:
   compatible:
@@ -34,8 +41,15 @@ properties:
       - const: qcom,saw2
 
   reg:
-    description: Base address and size of the SPM register region
-    maxItems: 1
+    items:
+      - description: Base address and size of the SPM register region
+      - description: Base address and size of the alias register region
+    minItems: 1
+
+  regulator:
+    type: boolean
+    description: Indicates that this SPM device acts as a regulator device
+      device for the core (CPU or Cache) the SPM is attached to.
 
 required:
   - compatible
-- 
2.39.2

[PATCH v6 02/11] dt-bindings: soc: qcom: qcom,saw2: define optional regulator node

[Dmitry Baryshkov]

The SAW2 device can optionally provide a voltage regulator supplying the
CPU core, cluster or L2 cache. Change the boolean 'regulator' property
into a proper regulator description. This breaks schema compatibility
for the sake of properly describing the regulator.

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 .../devicetree/bindings/soc/qcom/qcom,saw2.yaml   | 15 ++++++++++++++-
 1 file changed, 14 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,saw2.yaml b/Documentation/devicetree/bindings/soc/qcom/qcom,saw2.yaml
index 84b3f01d590c..a2d871ba8c45 100644
--- a/Documentation/devicetree/bindings/soc/qcom/qcom,saw2.yaml
+++ b/Documentation/devicetree/bindings/soc/qcom/qcom,saw2.yaml
@@ -47,7 +47,7 @@ properties:
     minItems: 1
 
   regulator:
-    type: boolean
+    $ref: /schemas/regulator/regulator.yaml#
     description: Indicates that this SPM device acts as a regulator device
       device for the core (CPU or Cache) the SPM is attached to.
 
@@ -96,4 +96,17 @@ examples:
         reg = <0x17912000 0x1000>;
     };
 
+  - |
+    /*
+     * Example 3: SAW2 with the bundled regulator definition.
+     */
+    power-manager@2089000 {
+        compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
+        reg = <0x02089000 0x1000>, <0x02009000 0x1000>;
+
+        regulator {
+            regulator-min-microvolt = <850000>;
+            regulator-max-microvolt = <1300000>;
+        };
+    };
 ...
-- 
2.39.2

[PATCH v6 03/11] soc: qcom: spm: remove driver-internal structures from the driver API

[Dmitry Baryshkov]

Move internal SPM driver structures to the driver itself, removing them
from the public API. The CPUidle driver doesn't use them at all.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 drivers/soc/qcom/spm.c | 20 ++++++++++++++++++++
 include/soc/qcom/spm.h | 23 +----------------------
 2 files changed, 21 insertions(+), 22 deletions(-)

diff --git a/drivers/soc/qcom/spm.c b/drivers/soc/qcom/spm.c
index 2f0b1bfe7658..b15435f7cb0d 100644
--- a/drivers/soc/qcom/spm.c
+++ b/drivers/soc/qcom/spm.c
@@ -36,6 +36,26 @@ enum spm_reg {
 	SPM_REG_NR,
 };
 
+#define MAX_PMIC_DATA		2
+#define MAX_SEQ_DATA		64
+
+struct spm_reg_data {
+	const u16 *reg_offset;
+	u32 spm_cfg;
+	u32 spm_dly;
+	u32 pmic_dly;
+	u32 pmic_data[MAX_PMIC_DATA];
+	u32 avs_ctl;
+	u32 avs_limit;
+	u8 seq[MAX_SEQ_DATA];
+	u8 start_index[PM_SLEEP_MODE_NR];
+};
+
+struct spm_driver_data {
+	void __iomem *reg_base;
+	const struct spm_reg_data *reg_data;
+};
+
 static const u16 spm_reg_offset_v4_1[SPM_REG_NR] = {
 	[SPM_REG_AVS_CTL]	= 0x904,
 	[SPM_REG_AVS_LIMIT]	= 0x908,
diff --git a/include/soc/qcom/spm.h b/include/soc/qcom/spm.h
index 4951f9d8b0bd..5b263c685812 100644
--- a/include/soc/qcom/spm.h
+++ b/include/soc/qcom/spm.h
@@ -7,11 +7,6 @@
 #ifndef __SPM_H__
 #define __SPM_H__
 
-#include <linux/cpuidle.h>
-
-#define MAX_PMIC_DATA		2
-#define MAX_SEQ_DATA		64
-
 enum pm_sleep_mode {
 	PM_SLEEP_MODE_STBY,
 	PM_SLEEP_MODE_RET,
@@ -20,23 +15,7 @@ enum pm_sleep_mode {
 	PM_SLEEP_MODE_NR,
 };
 
-struct spm_reg_data {
-	const u16 *reg_offset;
-	u32 spm_cfg;
-	u32 spm_dly;
-	u32 pmic_dly;
-	u32 pmic_data[MAX_PMIC_DATA];
-	u32 avs_ctl;
-	u32 avs_limit;
-	u8 seq[MAX_SEQ_DATA];
-	u8 start_index[PM_SLEEP_MODE_NR];
-};
-
-struct spm_driver_data {
-	void __iomem *reg_base;
-	const struct spm_reg_data *reg_data;
-};
-
+struct spm_driver_data;
 void spm_set_low_power_mode(struct spm_driver_data *drv,
 			    enum pm_sleep_mode mode);
 
-- 
2.39.2

[PATCH v6 04/11] soc: qcom: spm: add support for voltage regulator

[Dmitry Baryshkov]

The SPM / SAW2 device also provides a voltage regulator functionality
with optional AVS (Adaptive Voltage Scaling) support. The exact register
sequence and voltage ranges differs from device to device.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 drivers/soc/qcom/spm.c | 234 ++++++++++++++++++++++++++++++++++++++++-
 1 file changed, 229 insertions(+), 5 deletions(-)

diff --git a/drivers/soc/qcom/spm.c b/drivers/soc/qcom/spm.c
index b15435f7cb0d..5eefaec72a13 100644
--- a/drivers/soc/qcom/spm.c
+++ b/drivers/soc/qcom/spm.c
@@ -6,20 +6,40 @@
  * SAW power controller driver
  */
 
-#include <linux/kernel.h>
+#include <linux/bitfield.h>
+#include <linux/err.h>
 #include <linux/init.h>
 #include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/kernel.h>
+#include <linux/linear_range.h>
 #include <linux/module.h>
-#include <linux/slab.h>
 #include <linux/of.h>
-#include <linux/err.h>
 #include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/smp.h>
+
+#include <linux/regulator/driver.h>
+
 #include <soc/qcom/spm.h>
 
+#define FIELD_SET(current, mask, val)	\
+	(((current) & ~(mask)) | FIELD_PREP((mask), (val)))
+
 #define SPM_CTL_INDEX		0x7f
 #define SPM_CTL_INDEX_SHIFT	4
 #define SPM_CTL_EN		BIT(0)
 
+/* These registers might be specific to SPM 1.1 */
+#define SPM_VCTL_VLVL			GENMASK(7, 0)
+#define SPM_PMIC_DATA_0_VLVL		GENMASK(7, 0)
+#define SPM_PMIC_DATA_1_MIN_VSEL	GENMASK(5, 0)
+#define SPM_PMIC_DATA_1_MAX_VSEL	GENMASK(21, 16)
+
+#define SPM_1_1_AVS_CTL_AVS_ENABLED	BIT(27)
+#define SPM_AVS_CTL_MAX_VLVL		GENMASK(22, 17)
+#define SPM_AVS_CTL_MIN_VLVL		GENMASK(15, 10)
+
 enum spm_reg {
 	SPM_REG_CFG,
 	SPM_REG_SPM_CTL,
@@ -29,10 +49,12 @@ enum spm_reg {
 	SPM_REG_PMIC_DATA_1,
 	SPM_REG_VCTL,
 	SPM_REG_SEQ_ENTRY,
-	SPM_REG_SPM_STS,
+	SPM_REG_STS0,
+	SPM_REG_STS1,
 	SPM_REG_PMIC_STS,
 	SPM_REG_AVS_CTL,
 	SPM_REG_AVS_LIMIT,
+	SPM_REG_RST,
 	SPM_REG_NR,
 };
 
@@ -49,11 +71,20 @@ struct spm_reg_data {
 	u32 avs_limit;
 	u8 seq[MAX_SEQ_DATA];
 	u8 start_index[PM_SLEEP_MODE_NR];
+
+	smp_call_func_t set_vdd;
+	/* for now we support only a single range */
+	struct linear_range *range;
+	unsigned int ramp_delay;
+	unsigned int init_uV;
 };
 
 struct spm_driver_data {
 	void __iomem *reg_base;
 	const struct spm_reg_data *reg_data;
+	struct device *dev;
+	unsigned int volt_sel;
+	int reg_cpu;
 };
 
 static const u16 spm_reg_offset_v4_1[SPM_REG_NR] = {
@@ -189,6 +220,10 @@ static const struct spm_reg_data spm_reg_8226_cpu  = {
 
 static const u16 spm_reg_offset_v1_1[SPM_REG_NR] = {
 	[SPM_REG_CFG]		= 0x08,
+	[SPM_REG_STS0]		= 0x0c,
+	[SPM_REG_STS1]		= 0x10,
+	[SPM_REG_VCTL]		= 0x14,
+	[SPM_REG_AVS_CTL]	= 0x18,
 	[SPM_REG_SPM_CTL]	= 0x20,
 	[SPM_REG_PMIC_DLY]	= 0x24,
 	[SPM_REG_PMIC_DATA_0]	= 0x28,
@@ -196,7 +231,12 @@ static const u16 spm_reg_offset_v1_1[SPM_REG_NR] = {
 	[SPM_REG_SEQ_ENTRY]	= 0x80,
 };
 
+static void smp_set_vdd_v1_1(void *data);
+
 /* SPM register data for 8064 */
+static struct linear_range spm_v1_1_regulator_range =
+	REGULATOR_LINEAR_RANGE(700000, 0, 56, 12500);
+
 static const struct spm_reg_data spm_reg_8064_cpu = {
 	.reg_offset = spm_reg_offset_v1_1,
 	.spm_cfg = 0x1F,
@@ -207,6 +247,10 @@ static const struct spm_reg_data spm_reg_8064_cpu = {
 		0x10, 0x54, 0x30, 0x0C, 0x24, 0x30, 0x0F },
 	.start_index[PM_SLEEP_MODE_STBY] = 0,
 	.start_index[PM_SLEEP_MODE_SPC] = 2,
+	.set_vdd = smp_set_vdd_v1_1,
+	.range = &spm_v1_1_regulator_range,
+	.init_uV = 1300000,
+	.ramp_delay = 1250,
 };
 
 static inline void spm_register_write(struct spm_driver_data *drv,
@@ -258,6 +302,185 @@ void spm_set_low_power_mode(struct spm_driver_data *drv,
 	spm_register_write_sync(drv, SPM_REG_SPM_CTL, ctl_val);
 }
 
+static int spm_set_voltage_sel(struct regulator_dev *rdev, unsigned int selector)
+{
+	struct spm_driver_data *drv = rdev_get_drvdata(rdev);
+
+	drv->volt_sel = selector;
+
+	/* Always do the SAW register writes on the corresponding CPU */
+	return smp_call_function_single(drv->reg_cpu, drv->reg_data->set_vdd, drv, true);
+}
+
+static int spm_get_voltage_sel(struct regulator_dev *rdev)
+{
+	struct spm_driver_data *drv = rdev_get_drvdata(rdev);
+
+	return drv->volt_sel;
+}
+
+static const struct regulator_ops spm_reg_ops = {
+	.set_voltage_sel	= spm_set_voltage_sel,
+	.get_voltage_sel	= spm_get_voltage_sel,
+	.list_voltage		= regulator_list_voltage_linear_range,
+	.set_voltage_time_sel	= regulator_set_voltage_time_sel,
+};
+
+static void smp_set_vdd_v1_1(void *data)
+{
+	struct spm_driver_data *drv = data;
+	unsigned int vctl, data0, data1, avs_ctl, sts;
+	unsigned int vlevel, volt_sel;
+	bool avs_enabled;
+
+	volt_sel = drv->volt_sel;
+	vlevel = volt_sel | 0x80; /* band */
+
+	avs_ctl = spm_register_read(drv, SPM_REG_AVS_CTL);
+	vctl = spm_register_read(drv, SPM_REG_VCTL);
+	data0 = spm_register_read(drv, SPM_REG_PMIC_DATA_0);
+	data1 = spm_register_read(drv, SPM_REG_PMIC_DATA_1);
+
+	avs_enabled = avs_ctl & SPM_1_1_AVS_CTL_AVS_ENABLED;
+
+	/* If AVS is enabled, switch it off during the voltage change */
+	if (avs_enabled) {
+		avs_ctl &= ~SPM_1_1_AVS_CTL_AVS_ENABLED;
+		spm_register_write(drv, SPM_REG_AVS_CTL, avs_ctl);
+	}
+
+	/* Kick the state machine back to idle */
+	spm_register_write(drv, SPM_REG_RST, 1);
+
+	vctl = FIELD_SET(vctl, SPM_VCTL_VLVL, vlevel);
+	data0 = FIELD_SET(data0, SPM_PMIC_DATA_0_VLVL, vlevel);
+	data1 = FIELD_SET(data1, SPM_PMIC_DATA_1_MIN_VSEL, volt_sel);
+	data1 = FIELD_SET(data1, SPM_PMIC_DATA_1_MAX_VSEL, volt_sel);
+
+	spm_register_write(drv, SPM_REG_VCTL, vctl);
+	spm_register_write(drv, SPM_REG_PMIC_DATA_0, data0);
+	spm_register_write(drv, SPM_REG_PMIC_DATA_1, data1);
+
+	if (read_poll_timeout_atomic(spm_register_read,
+				     sts, sts == vlevel,
+				     1, 200, false,
+				     drv, SPM_REG_STS1)) {
+		dev_err_ratelimited(drv->dev, "timeout setting the voltage (%x %x)!\n", sts, vlevel);
+		goto enable_avs;
+	}
+
+	if (avs_enabled) {
+		unsigned int max_avs = volt_sel;
+		unsigned int min_avs = max(max_avs, 4U) - 4;
+
+		avs_ctl = FIELD_SET(avs_ctl, SPM_AVS_CTL_MIN_VLVL, min_avs);
+		avs_ctl = FIELD_SET(avs_ctl, SPM_AVS_CTL_MAX_VLVL, max_avs);
+		spm_register_write(drv, SPM_REG_AVS_CTL, avs_ctl);
+	}
+
+enable_avs:
+	if (avs_enabled) {
+		avs_ctl |= SPM_1_1_AVS_CTL_AVS_ENABLED;
+		spm_register_write(drv, SPM_REG_AVS_CTL, avs_ctl);
+	}
+}
+
+static int spm_get_cpu(struct device *dev)
+{
+	int cpu;
+	bool found;
+
+	for_each_possible_cpu(cpu) {
+		struct device_node *cpu_node, *saw_node;
+
+		cpu_node = of_cpu_device_node_get(cpu);
+		if (!cpu_node)
+			continue;
+
+		saw_node = of_parse_phandle(cpu_node, "qcom,saw", 0);
+		found = (saw_node == dev->of_node);
+		of_node_put(saw_node);
+		of_node_put(cpu_node);
+
+		if (found)
+			return cpu;
+	}
+
+	/* L2 SPM is not bound to any CPU, voltage setting is not supported */
+
+	return -EOPNOTSUPP;
+}
+
+#ifdef CONFIG_REGULATOR
+static int spm_register_regulator(struct device *dev, struct spm_driver_data *drv)
+{
+	struct regulator_config config = {
+		.dev = dev,
+		.driver_data = drv,
+	};
+	struct regulator_desc *rdesc;
+	struct regulator_dev *rdev;
+	int ret;
+	bool found;
+
+	if (!drv->reg_data->set_vdd)
+		return 0;
+
+	rdesc = devm_kzalloc(dev, sizeof(*rdesc), GFP_KERNEL);
+	if (!rdesc)
+		return -ENOMEM;
+
+	rdesc->name = "spm";
+	rdesc->of_match = of_match_ptr("regulator");
+	rdesc->type = REGULATOR_VOLTAGE;
+	rdesc->owner = THIS_MODULE;
+	rdesc->ops = &spm_reg_ops;
+
+	rdesc->linear_ranges = drv->reg_data->range;
+	rdesc->n_linear_ranges = 1;
+	rdesc->n_voltages = rdesc->linear_ranges[rdesc->n_linear_ranges - 1].max_sel + 1;
+	rdesc->ramp_delay = drv->reg_data->ramp_delay;
+
+	ret = spm_get_cpu(dev);
+	if (ret < 0)
+		return ret;
+
+	drv->reg_cpu = ret;
+	dev_dbg(dev, "SAW2 bound to CPU %d\n", drv->reg_cpu);
+
+	/*
+	 * Program initial voltage, otherwise registration will also try
+	 * setting the voltage, which might result in undervolting the CPU.
+	 */
+	drv->volt_sel = DIV_ROUND_UP(drv->reg_data->init_uV - rdesc->min_uV,
+				     rdesc->uV_step);
+	ret = linear_range_get_selector_high(drv->reg_data->range,
+					     drv->reg_data->init_uV,
+					     &drv->volt_sel,
+					     &found);
+	if (ret) {
+		dev_err(dev, "Initial uV value out of bounds\n");
+		return ret;
+	}
+
+	/* Always do the SAW register writes on the corresponding CPU */
+	smp_call_function_single(drv->reg_cpu, drv->reg_data->set_vdd, drv, true);
+
+	rdev = devm_regulator_register(dev, rdesc, &config);
+	if (IS_ERR(rdev)) {
+		dev_err(dev, "failed to register regulator\n");
+		return PTR_ERR(rdev);
+	}
+
+	return 0;
+}
+#else
+static int spm_register_regulator(struct device *dev, struct spm_driver_data *drv)
+{
+	return 0;
+}
+#endif
+
 static const struct of_device_id spm_match_table[] = {
 	{ .compatible = "qcom,sdm660-gold-saw2-v4.1-l2",
 	  .data = &spm_reg_660_gold_l2 },
@@ -308,6 +531,7 @@ static int spm_dev_probe(struct platform_device *pdev)
 		return -ENODEV;
 
 	drv->reg_data = match_id->data;
+	drv->dev = &pdev->dev;
 	platform_set_drvdata(pdev, drv);
 
 	/* Write the SPM sequences first.. */
@@ -335,7 +559,7 @@ static int spm_dev_probe(struct platform_device *pdev)
 	if (drv->reg_data->reg_offset[SPM_REG_SPM_CTL])
 		spm_set_low_power_mode(drv, PM_SLEEP_MODE_STBY);
 
-	return 0;
+	return spm_register_regulator(&pdev->dev, drv);
 }
 
 static struct platform_driver spm_driver = {
-- 
2.39.2

[PATCH v6 05/11] ARM: dts: qcom: apq8064: rename SAW nodes to power-manager

[Dmitry Baryshkov]

Per the power-domain.yaml, the power-controller node name is reserved
for power-domain providers. Rename SAW2 nodes to 'power-manager', the
name which is suggested by qcom,spm.yaml

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm/boot/dts/qcom/qcom-apq8064.dtsi | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/qcom/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom/qcom-apq8064.dtsi
index 95ac25e1a3b4..6832030c2c88 100644
--- a/arch/arm/boot/dts/qcom/qcom-apq8064.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-apq8064.dtsi
@@ -365,25 +365,25 @@ acc3: clock-controller@20b8000 {
 			#clock-cells = <0>;
 		};
 
-		saw0: power-controller@2089000 {
+		saw0: power-manager@2089000 {
 			compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
 			reg = <0x02089000 0x1000>, <0x02009000 0x1000>;
 			regulator;
 		};
 
-		saw1: power-controller@2099000 {
+		saw1: power-manager@2099000 {
 			compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
 			reg = <0x02099000 0x1000>, <0x02009000 0x1000>;
 			regulator;
 		};
 
-		saw2: power-controller@20a9000 {
+		saw2: power-manager@20a9000 {
 			compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
 			reg = <0x020a9000 0x1000>, <0x02009000 0x1000>;
 			regulator;
 		};
 
-		saw3: power-controller@20b9000 {
+		saw3: power-manager@20b9000 {
 			compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
 			reg = <0x020b9000 0x1000>, <0x02009000 0x1000>;
 			regulator;
-- 
2.39.2

[PATCH v6 06/11] ARM: dts: qcom: apq8064: declare SAW2 regulators

[Dmitry Baryshkov]

The SAW2 (SPM and AVS Wrapper) among other things is yet another way to
handle CPU-related PMIC regulators. Provide a way to control voltage of
these regulators.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm/boot/dts/qcom/qcom-apq8064.dtsi | 24 ++++++++++++++++++++----
 1 file changed, 20 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/qcom/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom/qcom-apq8064.dtsi
index 6832030c2c88..44c65ebf6c73 100644
--- a/arch/arm/boot/dts/qcom/qcom-apq8064.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-apq8064.dtsi
@@ -368,25 +368,41 @@ acc3: clock-controller@20b8000 {
 		saw0: power-manager@2089000 {
 			compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
 			reg = <0x02089000 0x1000>, <0x02009000 0x1000>;
-			regulator;
+
+			saw0_vreg: regulator {
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1300000>;
+			};
 		};
 
 		saw1: power-manager@2099000 {
 			compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
 			reg = <0x02099000 0x1000>, <0x02009000 0x1000>;
-			regulator;
+
+			saw1_vreg: regulator {
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1300000>;
+			};
 		};
 
 		saw2: power-manager@20a9000 {
 			compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
 			reg = <0x020a9000 0x1000>, <0x02009000 0x1000>;
-			regulator;
+
+			saw2_vreg: regulator {
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1300000>;
+			};
 		};
 
 		saw3: power-manager@20b9000 {
 			compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
 			reg = <0x020b9000 0x1000>, <0x02009000 0x1000>;
-			regulator;
+
+			saw3_vreg: regulator {
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1300000>;
+			};
 		};
 
 		sps_sic_non_secure: sps-sic-non-secure@12100000 {
-- 
2.39.2

[PATCH v6 07/11] ARM: dts: qcom: msm8960: declare SAW2 regulators

[Dmitry Baryshkov]

The SAW2 (SPM and AVS Wrapper) among other things is yet another way to
handle CPU-related PMIC regulators. Provide a way to control voltage of
these regulators.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm/boot/dts/qcom/qcom-msm8960.dtsi | 12 ++++++++++--
 1 file changed, 10 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/qcom/qcom-msm8960.dtsi b/arch/arm/boot/dts/qcom/qcom-msm8960.dtsi
index f420740e068e..0ab340405784 100644
--- a/arch/arm/boot/dts/qcom/qcom-msm8960.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-msm8960.dtsi
@@ -223,13 +223,21 @@ acc1: clock-controller@2098000 {
 		saw0: regulator@2089000 {
 			compatible = "qcom,saw2";
 			reg = <0x02089000 0x1000>, <0x02009000 0x1000>;
-			regulator;
+
+			saw0_vreg: regulator {
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1300000>;
+			};
 		};
 
 		saw1: regulator@2099000 {
 			compatible = "qcom,saw2";
 			reg = <0x02099000 0x1000>, <0x02009000 0x1000>;
-			regulator;
+
+			saw1_vreg: regulator {
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1300000>;
+			};
 		};
 
 		gsbi5: gsbi@16400000 {
-- 
2.39.2

[PATCH v6 08/11] ARM: dts: qcom: apq8084: drop 'regulator' property from SAW2 device

[Dmitry Baryshkov]

The SAW2 device should describe the regulator constraints rather than
just declaring that it has the regulator.

Drop the 'regulator' property. If/when CPU voltage scaling is
implemented for this platform, proper regulator node show be added
instead.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm/boot/dts/qcom/qcom-apq8084.dtsi | 1 -
 1 file changed, 1 deletion(-)

diff --git a/arch/arm/boot/dts/qcom/qcom-apq8084.dtsi b/arch/arm/boot/dts/qcom/qcom-apq8084.dtsi
index 2b1f9d0fb510..24bc2cbfbd96 100644
--- a/arch/arm/boot/dts/qcom/qcom-apq8084.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-apq8084.dtsi
@@ -652,7 +652,6 @@ saw3: power-controller@f90b9000 {
 		saw_l2: power-controller@f9012000 {
 			compatible = "qcom,saw2";
 			reg = <0xf9012000 0x1000>;
-			regulator;
 		};
 
 		acc0: power-manager@f9088000 {
-- 
2.39.2

[PATCH v6 09/11] ARM: dts: qcom: msm8974: drop 'regulator' property from SAW2 device

[Dmitry Baryshkov]

The SAW2 device should describe the regulator constraints rather than
just declaring that it has the regulator.

Drop the 'regulator' property. If/when CPU voltage scaling is
implemented for this platform, proper regulator node show be added
instead.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm/boot/dts/qcom/qcom-msm8974.dtsi | 1 -
 1 file changed, 1 deletion(-)

diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom/qcom-msm8974.dtsi
index ee202f3f161e..3e1e88d69c2e 100644
--- a/arch/arm/boot/dts/qcom/qcom-msm8974.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-msm8974.dtsi
@@ -349,7 +349,6 @@ apcs: syscon@f9011000 {
 		saw_l2: power-controller@f9012000 {
 			compatible = "qcom,saw2";
 			reg = <0xf9012000 0x1000>;
-			regulator;
 		};
 
 		watchdog@f9017000 {
-- 
2.39.2

[PATCH v6 10/11] ARM: dts: qcom: ipq4019: drop 'regulator' property from SAW2 devices

[Dmitry Baryshkov]

The SAW2 device should describe the regulator constraints rather than
just declaring that it has the regulator.

Drop the 'regulator' property. If/when CPU voltage scaling is
implemented for this platform, proper regulator nodes show be added
instead.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm/boot/dts/qcom/qcom-ipq4019.dtsi | 5 -----
 1 file changed, 5 deletions(-)

diff --git a/arch/arm/boot/dts/qcom/qcom-ipq4019.dtsi b/arch/arm/boot/dts/qcom/qcom-ipq4019.dtsi
index 9844e0b7cff9..d7bd97997ff9 100644
--- a/arch/arm/boot/dts/qcom/qcom-ipq4019.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-ipq4019.dtsi
@@ -353,31 +353,26 @@ acc3: power-manager@b0b8000 {
 		saw0: regulator@b089000 {
 			compatible = "qcom,saw2";
 			reg = <0x0b089000 0x1000>, <0x0b009000 0x1000>;
-			regulator;
 		};
 
 		saw1: regulator@b099000 {
 			compatible = "qcom,saw2";
 			reg = <0x0b099000 0x1000>, <0x0b009000 0x1000>;
-			regulator;
 		};
 
 		saw2: regulator@b0a9000 {
 			compatible = "qcom,saw2";
 			reg = <0x0b0a9000 0x1000>, <0x0b009000 0x1000>;
-			regulator;
 		};
 
 		saw3: regulator@b0b9000 {
 			compatible = "qcom,saw2";
 			reg = <0x0b0b9000 0x1000>, <0x0b009000 0x1000>;
-			regulator;
 		};
 
 		saw_l2: regulator@b012000 {
 			compatible = "qcom,saw2";
 			reg = <0xb012000 0x1000>;
-			regulator;
 		};
 
 		blsp1_uart1: serial@78af000 {
-- 
2.39.2

[PATCH v6 11/11] ARM: dts: qcom: ipq8064: drop 'regulator' property from SAW2 devices

[Dmitry Baryshkov]

The SAW2 device should describe the regulator constraints rather than
just declaring that it has the regulator.

Drop the 'regulator' property. If/when CPU voltage scaling is
implemented for this platform, proper regulator nodes show be added
instead.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm/boot/dts/qcom/qcom-ipq8064.dtsi | 2 --
 1 file changed, 2 deletions(-)

diff --git a/arch/arm/boot/dts/qcom/qcom-ipq8064.dtsi b/arch/arm/boot/dts/qcom/qcom-ipq8064.dtsi
index c3677440b786..191d1cb27cb7 100644
--- a/arch/arm/boot/dts/qcom/qcom-ipq8064.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-ipq8064.dtsi
@@ -589,7 +589,6 @@ acc0: clock-controller@2088000 {
 		saw0: regulator@2089000 {
 			compatible = "qcom,saw2";
 			reg = <0x02089000 0x1000>, <0x02009000 0x1000>;
-			regulator;
 		};
 
 		acc1: clock-controller@2098000 {
@@ -604,7 +603,6 @@ acc1: clock-controller@2098000 {
 		saw1: regulator@2099000 {
 			compatible = "qcom,saw2";
 			reg = <0x02099000 0x1000>, <0x02009000 0x1000>;
-			regulator;
 		};
 
 		nss_common: syscon@3000000 {
-- 
2.39.2

Re: [PATCH v6 03/11] soc: qcom: spm: remove driver-internal structures from the driver API

[Konrad Dybcio]

On 8.12.2023 01:44, Dmitry Baryshkov wrote:
> Move internal SPM driver structures to the driver itself, removing them
> from the public API. The CPUidle driver doesn't use them at all.
> 
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>

Konrad

Re: [PATCH v6 09/11] ARM: dts: qcom: msm8974: drop 'regulator' property from SAW2 device

[Luca Weiss]

On Freitag, 8. Dezember 2023 01:44:15 CET Dmitry Baryshkov wrote:
> The SAW2 device should describe the regulator constraints rather than
> just declaring that it has the regulator.
> 
> Drop the 'regulator' property. If/when CPU voltage scaling is
> implemented for this platform, proper regulator node show be added
> instead.
> 
> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> ---
>  arch/arm/boot/dts/qcom/qcom-msm8974.dtsi | 1 -
>  1 file changed, 1 deletion(-)
> 
> diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974.dtsi
> b/arch/arm/boot/dts/qcom/qcom-msm8974.dtsi index ee202f3f161e..3e1e88d69c2e
> 100644
> --- a/arch/arm/boot/dts/qcom/qcom-msm8974.dtsi
> +++ b/arch/arm/boot/dts/qcom/qcom-msm8974.dtsi
> @@ -349,7 +349,6 @@ apcs: syscon@f9011000 {
>  		saw_l2: power-controller@f9012000 {
>  			compatible = "qcom,saw2";

Hi Dmitry,

With the patches touching the dt bindings I don't see this "qcom,saw2" 
compatible without a second one being accepted by the bindings? Do you have a 
suggestion what do to there? Also thinking about msm8226 which also has a 
saw_l2.

Thanks for working on this old stuff!

Regards
Luca

>  			reg = <0xf9012000 0x1000>;
> -			regulator;
>  		};
> 
>  		watchdog@f9017000 {