From: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
To: Robert Foss <rfoss@kernel.org>, Todor Tomov <todor.too@gmail.com>,
Bjorn Andersson <andersson@kernel.org>,
Konrad Dybcio <konrad.dybcio@linaro.org>,
Mauro Carvalho Chehab <mchehab@kernel.org>,
Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
Conor Dooley <conor+dt@kernel.org>
Cc: linux-media@vger.kernel.org, linux-arm-msm@vger.kernel.org,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Subject: [PATCH v2 3/4] arm64: dts: qcom: sc8280xp: camss: Add CCI definitions
Date: Fri, 05 Jan 2024 20:39:07 +0000 [thread overview]
Message-ID: <20240105-linux-next-24-01-02-sc8280xp-camss-core-dtsi-v2-3-7a57b8b07398@linaro.org> (raw)
In-Reply-To: <20240105-linux-next-24-01-02-sc8280xp-camss-core-dtsi-v2-0-7a57b8b07398@linaro.org>
sc8280xp has four Camera Control Interface (CCI) blocks which pinout to
two I2C master controllers for each CCI.
The CCI I2C pins are not muxed so we define them in the dtsi.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
---
arch/arm64/boot/dts/qcom/sc8280xp.dtsi | 316 +++++++++++++++++++++++++++++++++
1 file changed, 316 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sc8280xp.dtsi b/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
index febf28356ff8..2d7ae19dda3a 100644
--- a/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
@@ -3451,6 +3451,162 @@ usb_1_role_switch: endpoint {
};
};
+ cci0: cci@ac4a000 {
+ compatible = "qcom,sc8280xp-cci", "qcom,msm8996-cci";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reg = <0 0x0ac4a000 0 0x1000>;
+ interrupts = <GIC_SPI 460 IRQ_TYPE_EDGE_RISING>;
+ power-domains = <&camcc TITAN_TOP_GDSC>;
+
+ clocks = <&camcc CAMCC_CAMNOC_AXI_CLK>,
+ <&camcc CAMCC_SLOW_AHB_CLK_SRC>,
+ <&camcc CAMCC_CPAS_AHB_CLK>,
+ <&camcc CAMCC_CCI_0_CLK>;
+ clock-names = "camnoc_axi",
+ "slow_ahb_src",
+ "cpas_ahb",
+ "cci";
+
+ pinctrl-0 = <&cci0_default>;
+ pinctrl-1 = <&cci0_sleep>;
+ pinctrl-names = "default", "sleep";
+
+ status = "disabled";
+
+ cci0_i2c0: i2c-bus@0 {
+ reg = <0>;
+ clock-frequency = <1000000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ cci0_i2c1: i2c-bus@1 {
+ reg = <1>;
+ clock-frequency = <1000000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
+ cci1: cci@ac4b000 {
+ compatible = "qcom,sc8280xp-cci", "qcom,msm8996-cci";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reg = <0 0x0ac4b000 0 0x1000>;
+ interrupts = <GIC_SPI 271 IRQ_TYPE_EDGE_RISING>;
+ power-domains = <&camcc TITAN_TOP_GDSC>;
+
+ clocks = <&camcc CAMCC_CAMNOC_AXI_CLK>,
+ <&camcc CAMCC_SLOW_AHB_CLK_SRC>,
+ <&camcc CAMCC_CPAS_AHB_CLK>,
+ <&camcc CAMCC_CCI_1_CLK>;
+ clock-names = "camnoc_axi",
+ "slow_ahb_src",
+ "cpas_ahb",
+ "cci";
+
+ pinctrl-0 = <&cci1_default>;
+ pinctrl-1 = <&cci1_sleep>;
+ pinctrl-names = "default", "sleep";
+
+ status = "disabled";
+
+ cci1_i2c0: i2c-bus@0 {
+ reg = <0>;
+ clock-frequency = <1000000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ cci1_i2c1: i2c-bus@1 {
+ reg = <1>;
+ clock-frequency = <1000000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
+ cci2: cci@ac4c000 {
+ compatible = "qcom,sc8280xp-cci", "qcom,msm8996-cci";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reg = <0 0x0ac4c000 0 0x1000>;
+ interrupts = <GIC_SPI 651 IRQ_TYPE_EDGE_RISING>;
+ power-domains = <&camcc TITAN_TOP_GDSC>;
+
+ clocks = <&camcc CAMCC_CAMNOC_AXI_CLK>,
+ <&camcc CAMCC_SLOW_AHB_CLK_SRC>,
+ <&camcc CAMCC_CPAS_AHB_CLK>,
+ <&camcc CAMCC_CCI_2_CLK>;
+ clock-names = "camnoc_axi",
+ "slow_ahb_src",
+ "cpas_ahb",
+ "cci";
+
+ pinctrl-0 = <&cci2_default>;
+ pinctrl-1 = <&cci2_sleep>;
+ pinctrl-names = "default", "sleep";
+
+ status = "disabled";
+
+ cci2_i2c0: i2c-bus@0 {
+ reg = <0>;
+ clock-frequency = <1000000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ cci2_i2c1: i2c-bus@1 {
+ reg = <1>;
+ clock-frequency = <1000000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
+ cci3: cci@ac4d000 {
+ compatible = "qcom,sc8280xp-cci", "qcom,msm8996-cci";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reg = <0 0x0ac4d000 0 0x1000>;
+ interrupts = <GIC_SPI 650 IRQ_TYPE_EDGE_RISING>;
+ power-domains = <&camcc TITAN_TOP_GDSC>;
+
+ clocks = <&camcc CAMCC_CAMNOC_AXI_CLK>,
+ <&camcc CAMCC_SLOW_AHB_CLK_SRC>,
+ <&camcc CAMCC_CPAS_AHB_CLK>,
+ <&camcc CAMCC_CCI_3_CLK>;
+ clock-names = "camnoc_axi",
+ "slow_ahb_src",
+ "cpas_ahb",
+ "cci";
+
+ pinctrl-0 = <&cci3_default>;
+ pinctrl-1 = <&cci3_sleep>;
+ pinctrl-names = "default", "sleep";
+
+ status = "disabled";
+
+ cci3_i2c0: i2c-bus@0 {
+ reg = <0>;
+ clock-frequency = <1000000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ cci3_i2c1: i2c-bus@1 {
+ reg = <1>;
+ clock-frequency = <1000000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
camcc: clock-controller@ad00000 {
compatible = "qcom,sc8280xp-camcc";
reg = <0 0x0ad00000 0 0x20000>;
@@ -4076,6 +4232,166 @@ tlmm: pinctrl@f100000 {
#interrupt-cells = <2>;
gpio-ranges = <&tlmm 0 0 230>;
wakeup-parent = <&pdc>;
+
+ cci0_default: cci0-default-state {
+ cci0_i2c0_default: cci0-i2c0-default-pins {
+ /* cci_i2c_sda0, cci_i2c_scl0 */
+ pins = "gpio113", "gpio114";
+ function = "cci_i2c";
+
+ bias-pull-up;
+ drive-strength = <2>; /* 2 mA */
+ };
+
+ cci0_i2c1_default: cci0-i2c1-default-pins {
+ /* cci_i2c_sda1, cci_i2c_scl1 */
+ pins = "gpio115", "gpio116";
+ function = "cci_i2c";
+
+ bias-pull-up;
+ drive-strength = <2>; /* 2 mA */
+ };
+ };
+
+ cci0_sleep: cci0-sleep-state {
+ cci0_i2c0_sleep: cci0-i2c0-sleep-pins {
+ /* cci_i2c_sda0, cci_i2c_scl0 */
+ pins = "gpio113", "gpio114";
+ function = "cci_i2c";
+
+ drive-strength = <2>; /* 2 mA */
+ bias-pull-down;
+ };
+
+ cci0_i2c1_sleep: cci0-i2c1-sleep-pins {
+ /* cci_i2c_sda1, cci_i2c_scl1 */
+ pins = "gpio115", "gpio116";
+ function = "cci_i2c";
+
+ drive-strength = <2>; /* 2 mA */
+ bias-pull-down;
+ };
+ };
+
+ cci1_default: cci1-default-state {
+ cci1_i2c0_default: cci1-i2c0-default-pins {
+ /* cci_i2c_sda2, cci_i2c_scl2 */
+ pins = "gpio10","gpio11";
+ function = "cci_i2c";
+
+ bias-pull-up;
+ drive-strength = <2>; /* 2 mA */
+ };
+
+ cci1_i2c1_default: cci1-i2c1-default-pins {
+ /* cci_i2c_sda3, cci_i2c_scl3 */
+ pins = "gpio123","gpio124";
+ function = "cci_i2c";
+
+ bias-pull-up;
+ drive-strength = <2>; /* 2 mA */
+ };
+ };
+
+ cci1_sleep: cci1-sleep-state {
+ cci1_i2c0_sleep: cci1-i2c0-sleep-pins {
+ /* cci_i2c_sda2, cci_i2c_scl2 */
+ pins = "gpio10","gpio11";
+ function = "cci_i2c";
+
+ bias-pull-down;
+ drive-strength = <2>; /* 2 mA */
+ };
+
+ cci1_i2c1_sleep: cci1-i2c1-sleep-pins {
+ /* cci_i2c_sda3, cci_i2c_scl3 */
+ pins = "gpio123","gpio124";
+ function = "cci_i2c";
+
+ bias-pull-down;
+ drive-strength = <2>; /* 2 mA */
+ };
+ };
+
+ cci2_default: cci2-default-state {
+ cci2_i2c0_default: cci2-i2c0-default-pins {
+ /* cci_i2c_sda4, cci_i2c_scl4 */
+ pins = "gpio117","gpio118";
+ function = "cci_i2c";
+
+ bias-pull-up;
+ drive-strength = <2>; /* 2 mA */
+ };
+
+ cci2_i2c1_default: cci2-i2c1-default-pins {
+ /* cci_i2c_sda5, cci_i2c_scl5 */
+ pins = "gpio12","gpio13";
+ function = "cci_i2c";
+
+ bias-pull-up;
+ drive-strength = <2>; /* 2 mA */
+ };
+ };
+
+ cci2_sleep: cci2-sleep-state {
+ cci2_i2c0_sleep: cci2-i2c0-sleep-pins {
+ /* cci_i2c_sda4, cci_i2c_scl4 */
+ pins = "gpio117","gpio118";
+ function = "cci_i2c";
+
+ bias-pull-down;
+ drive-strength = <2>; /* 2 mA */
+ };
+
+ cci2_i2c1_sleep: cci2-i2c1-sleep-pins {
+ /* cci_i2c_sda5, cci_i2c_scl5 */
+ pins = "gpio12","gpio13";
+ function = "cci_i2c";
+
+ bias-pull-down;
+ drive-strength = <2>; /* 2 mA */
+ };
+ };
+
+ cci3_default: cci3-default-state {
+ cci3_i2c0_default: cci3-i2c0-default-pins {
+ /* cci_i2c_sda6, cci_i2c_scl6 */
+ pins = "gpio145","gpio146";
+ function = "cci_i2c";
+
+ bias-pull-up;
+ drive-strength = <2>; /* 2 mA */
+ };
+
+ cci3_i2c1_default: cci3-i2c1-default-pins {
+ /* cci_i2c_sda7, cci_i2c_scl7 */
+ pins = "gpio164","gpio165";
+ function = "cci_i2c";
+
+ bias-pull-up;
+ drive-strength = <2>; /* 2 mA */
+ };
+ };
+
+ cci3_sleep: cci3-sleep-state {
+ cci3_i2c0_sleep: cci3-i2c0-sleep-pins {
+ /* cci_i2c_sda6, cci_i2c_scl6 */
+ pins = "gpio145","gpio146";
+ function = "cci_i2c";
+
+ bias-pull-down;
+ drive-strength = <2>; /* 2 mA */
+ };
+
+ cci3_i2c1_sleep: cci3-i2c1-sleep-pins {
+ /* cci_i2c_sda7, cci_i2c_scl7 */
+ pins = "gpio164","gpio165";
+ function = "cci_i2c";
+
+ bias-pull-down;
+ drive-strength = <2>; /* 2 mA */
+ };
+ };
};
apps_smmu: iommu@15000000 {
--
2.42.0
next prev parent reply other threads:[~2024-01-05 20:39 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-01-05 20:39 [PATCH v2 0/4] arm64: dts: qcom: sc8280xp: Add CAMSS core dtsi support Bryan O'Donoghue
2024-01-05 20:39 ` [PATCH v2 1/4] dt-bindings: i2c: qcom-cci: Document sc8280xp compatible Bryan O'Donoghue
2024-01-08 9:45 ` Krzysztof Kozlowski
2024-01-05 20:39 ` [PATCH v2 2/4] media: dt-bindings: media: camss: Add qcom,sc8280xp-camss binding Bryan O'Donoghue
2024-01-05 20:42 ` Bryan O'Donoghue
2024-01-05 22:34 ` Rob Herring
2024-01-05 20:39 ` Bryan O'Donoghue [this message]
2024-01-05 20:39 ` [PATCH v2 4/4] arm64: dts: qcom: sc8280xp: camss: Add CAMSS block definition Bryan O'Donoghue
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20240105-linux-next-24-01-02-sc8280xp-camss-core-dtsi-v2-3-7a57b8b07398@linaro.org \
--to=bryan.odonoghue@linaro.org \
--cc=andersson@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=konrad.dybcio@linaro.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-media@vger.kernel.org \
--cc=mchehab@kernel.org \
--cc=rfoss@kernel.org \
--cc=robh+dt@kernel.org \
--cc=todor.too@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).