* [PATCH v4 00/12] arm64: dts: imx8mm-kontron: DT updates
@ 2024-01-08 8:48 Frieder Schrempf
2024-01-08 8:48 ` [PATCH v4 01/12] arm64: dts: imx8mm-kontron: Disable pullups for I2C signals on OSM-S i.MX8MM Frieder Schrempf
` (12 more replies)
0 siblings, 13 replies; 14+ messages in thread
From: Frieder Schrempf @ 2024-01-08 8:48 UTC (permalink / raw)
To: Conor Dooley, devicetree, Frieder Schrempf, Krzysztof Kozlowski,
linux-arm-kernel, linux-kernel, Rob Herring, Sascha Hauer,
Shawn Guo
Cc: Fabio Estevam, Krzysztof Kozlowski, NXP Linux Team,
Pengutronix Kernel Team
From: Frieder Schrempf <frieder.schrempf@kontron.de>
This patchset contains several improvements and updates for the devicetrees
for the i.MX8MM modules and boards by Kontron Electronics GmbH.
* Misc cleanups and small fixes
* OSM-S i.MX8MM module refactoring and update to latest HW revision
Changes in v4:
* Rebase to Shawn's imx/dt64 branch
* Drop patches 1 and 2 (display support) as there are unresolved DTC warnings
and I am not sure how to resolve them at the moment.
Changes in v3:
* Address Shawn's review comments for patch 1, 2 and 14 (thanks!)
Changes in v2:
* Rework DSI mux GPIO logic to be compatible with overlay
* Switch from 4 to 2 DSI lanes for LVDS bridge to fix non-working display
Frieder Schrempf (12):
arm64: dts: imx8mm-kontron: Disable pullups for I2C signals on OSM-S
i.MX8MM
arm64: dts: imx8mm-kontron: Disable pullups for I2C signals on SL/BL
i.MX8MM
arm64: dts: imx8mm-kontron: Disable pullups for onboard UART signals
on BL OSM-S board
arm64: dts: imx8mm-kontron: Disable pullups for onboard UART signals
on BL board
arm64: dts: imx8mm-kontron: Disable pull resistors for SD card signals
on BL OSM-S board
arm64: dts: imx8mm-kontron: Disable pull resistors for SD card signals
on BL board
arm64: dts: imx8mm-kontron: Fix interrupt for RTC on OSM-S i.MX8MM
module
arm64: dts: imx8mm-kontron: Fix OSM-S devicetrees to match latest
hardware
arm64: dts: imx8mm-kontron: Disable uneffective PUE bit in SDIO IOMUX
arm64: dts: imx8mm-kontron: Remove useless trickle-diode-disable from
RTC node
arm64: dts: imx8mm-kontron: Add I2C EEPROM on OSM-S Kontron i.MX8MM
arm64: dts: imx8mm-kontron: Refactor devicetree for OSM-S module and
board
.../dts/freescale/imx8mm-kontron-bl-osm-s.dts | 295 +++------
.../boot/dts/freescale/imx8mm-kontron-bl.dts | 38 +-
.../dts/freescale/imx8mm-kontron-osm-s.dtsi | 567 +++++++++++++++++-
.../boot/dts/freescale/imx8mm-kontron-sl.dtsi | 4 +-
4 files changed, 670 insertions(+), 234 deletions(-)
--
2.43.0
^ permalink raw reply [flat|nested] 14+ messages in thread* [PATCH v4 01/12] arm64: dts: imx8mm-kontron: Disable pullups for I2C signals on OSM-S i.MX8MM 2024-01-08 8:48 [PATCH v4 00/12] arm64: dts: imx8mm-kontron: DT updates Frieder Schrempf @ 2024-01-08 8:48 ` Frieder Schrempf 2024-01-08 8:48 ` [PATCH v4 02/12] arm64: dts: imx8mm-kontron: Disable pullups for I2C signals on SL/BL i.MX8MM Frieder Schrempf ` (11 subsequent siblings) 12 siblings, 0 replies; 14+ messages in thread From: Frieder Schrempf @ 2024-01-08 8:48 UTC (permalink / raw) To: Conor Dooley, devicetree, Frieder Schrempf, Krzysztof Kozlowski, linux-arm-kernel, linux-kernel, Rob Herring, Sascha Hauer, Shawn Guo Cc: Fabio Estevam, NXP Linux Team, Pengutronix Kernel Team From: Frieder Schrempf <frieder.schrempf@kontron.de> There are external pullup resistors on the board and due to silicon errata ERR050080 let's disable the internal ones to prevent any unwanted behavior in case they wear out. Fixes: de9618e84f76 ("arm64: dts: Add support for Kontron SL/BL i.MX8MM OSM-S") Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> --- Changes for v3: * none Changes for v2: * none --- arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts | 4 ++-- arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi | 4 ++-- 2 files changed, 4 insertions(+), 4 deletions(-) diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts index 8b16bd68576c0..0730c22e5b6b9 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts @@ -294,8 +294,8 @@ MX8MM_IOMUXC_SAI3_MCLK_GPIO5_IO2 0x19 pinctrl_i2c4: i2c4grp { fsl,pins = < - MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL 0x400001c3 - MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA 0x400001c3 + MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL 0x40000083 + MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA 0x40000083 >; }; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi index 6e75ab879bf59..3e7db968f7e64 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi @@ -252,8 +252,8 @@ MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9 0x19 pinctrl_i2c1: i2c1grp { fsl,pins = < - MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c3 - MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c3 + MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x40000083 + MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x40000083 >; }; -- 2.43.0 ^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH v4 02/12] arm64: dts: imx8mm-kontron: Disable pullups for I2C signals on SL/BL i.MX8MM 2024-01-08 8:48 [PATCH v4 00/12] arm64: dts: imx8mm-kontron: DT updates Frieder Schrempf 2024-01-08 8:48 ` [PATCH v4 01/12] arm64: dts: imx8mm-kontron: Disable pullups for I2C signals on OSM-S i.MX8MM Frieder Schrempf @ 2024-01-08 8:48 ` Frieder Schrempf 2024-01-08 8:49 ` [PATCH v4 03/12] arm64: dts: imx8mm-kontron: Disable pullups for onboard UART signals on BL OSM-S board Frieder Schrempf ` (10 subsequent siblings) 12 siblings, 0 replies; 14+ messages in thread From: Frieder Schrempf @ 2024-01-08 8:48 UTC (permalink / raw) To: Conor Dooley, devicetree, Frieder Schrempf, Krzysztof Kozlowski, linux-arm-kernel, linux-kernel, Rob Herring, Sascha Hauer, Shawn Guo Cc: Fabio Estevam, Krzysztof Kozlowski, NXP Linux Team, Pengutronix Kernel Team From: Frieder Schrempf <frieder.schrempf@kontron.de> There are external pullup resistors on the board and due to silicon errata ERR050080 let's disable the internal ones to prevent any unwanted behavior in case they wear out. Fixes: 8668d8b2e67f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards") Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> --- Changes for v3: * none Changes for v2: * none --- arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts | 4 ++-- arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi | 4 ++-- 2 files changed, 4 insertions(+), 4 deletions(-) diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts index dcec57c20399e..5fd2e45258b11 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts @@ -279,8 +279,8 @@ MX8MM_IOMUXC_SAI3_MCLK_GPIO5_IO2 0x19 pinctrl_i2c4: i2c4grp { fsl,pins = < - MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL 0x400001c3 - MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA 0x400001c3 + MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL 0x40000083 + MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA 0x40000083 >; }; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi index 1f8326613ee9e..2076148e08627 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi @@ -237,8 +237,8 @@ MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9 0x19 pinctrl_i2c1: i2c1grp { fsl,pins = < - MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c3 - MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c3 + MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x40000083 + MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x40000083 >; }; -- 2.43.0 ^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH v4 03/12] arm64: dts: imx8mm-kontron: Disable pullups for onboard UART signals on BL OSM-S board 2024-01-08 8:48 [PATCH v4 00/12] arm64: dts: imx8mm-kontron: DT updates Frieder Schrempf 2024-01-08 8:48 ` [PATCH v4 01/12] arm64: dts: imx8mm-kontron: Disable pullups for I2C signals on OSM-S i.MX8MM Frieder Schrempf 2024-01-08 8:48 ` [PATCH v4 02/12] arm64: dts: imx8mm-kontron: Disable pullups for I2C signals on SL/BL i.MX8MM Frieder Schrempf @ 2024-01-08 8:49 ` Frieder Schrempf 2024-01-08 8:49 ` [PATCH v4 04/12] arm64: dts: imx8mm-kontron: Disable pullups for onboard UART signals on BL board Frieder Schrempf ` (9 subsequent siblings) 12 siblings, 0 replies; 14+ messages in thread From: Frieder Schrempf @ 2024-01-08 8:49 UTC (permalink / raw) To: Conor Dooley, devicetree, Frieder Schrempf, Krzysztof Kozlowski, linux-arm-kernel, linux-kernel, Rob Herring, Sascha Hauer, Shawn Guo Cc: Fabio Estevam, NXP Linux Team, Pengutronix Kernel Team From: Frieder Schrempf <frieder.schrempf@kontron.de> These signals are actively driven by the SoC or by the onboard transceiver. There's no need to enable the internal pull resistors and due to silicon errata ERR050080 let's disable the internal ones to prevent any unwanted behavior in case they wear out. Fixes: de9618e84f76 ("arm64: dts: Add support for Kontron SL/BL i.MX8MM OSM-S") Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> --- Changes for v3: * none Changes for v2: * none --- .../dts/freescale/imx8mm-kontron-bl-osm-s.dts | 16 ++++++++-------- 1 file changed, 8 insertions(+), 8 deletions(-) diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts index 0730c22e5b6b9..1dd03ef0a7835 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts @@ -313,19 +313,19 @@ MX8MM_IOMUXC_SAI5_MCLK_GPIO3_IO25 0x19 pinctrl_uart1: uart1grp { fsl,pins = < - MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX 0x140 - MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX 0x140 - MX8MM_IOMUXC_SAI2_RXD0_UART1_DCE_RTS_B 0x140 - MX8MM_IOMUXC_SAI2_TXFS_UART1_DCE_CTS_B 0x140 + MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX 0x0 + MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX 0x0 + MX8MM_IOMUXC_SAI2_RXD0_UART1_DCE_RTS_B 0x0 + MX8MM_IOMUXC_SAI2_TXFS_UART1_DCE_CTS_B 0x0 >; }; pinctrl_uart2: uart2grp { fsl,pins = < - MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX 0x140 - MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX 0x140 - MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B 0x140 - MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B 0x140 + MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX 0x0 + MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX 0x0 + MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B 0x0 + MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B 0x0 >; }; -- 2.43.0 ^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH v4 04/12] arm64: dts: imx8mm-kontron: Disable pullups for onboard UART signals on BL board 2024-01-08 8:48 [PATCH v4 00/12] arm64: dts: imx8mm-kontron: DT updates Frieder Schrempf ` (2 preceding siblings ...) 2024-01-08 8:49 ` [PATCH v4 03/12] arm64: dts: imx8mm-kontron: Disable pullups for onboard UART signals on BL OSM-S board Frieder Schrempf @ 2024-01-08 8:49 ` Frieder Schrempf 2024-01-08 8:49 ` [PATCH v4 05/12] arm64: dts: imx8mm-kontron: Disable pull resistors for SD card signals on BL OSM-S board Frieder Schrempf ` (8 subsequent siblings) 12 siblings, 0 replies; 14+ messages in thread From: Frieder Schrempf @ 2024-01-08 8:49 UTC (permalink / raw) To: Conor Dooley, devicetree, Frieder Schrempf, Krzysztof Kozlowski, linux-arm-kernel, linux-kernel, Rob Herring, Sascha Hauer, Shawn Guo Cc: Fabio Estevam, Krzysztof Kozlowski, NXP Linux Team, Pengutronix Kernel Team From: Frieder Schrempf <frieder.schrempf@kontron.de> These signals are actively driven by the SoC or by the onboard transceiver. There's no need to enable the internal pull resistors and due to silicon errata ERR050080 let's disable the internal ones to prevent any unwanted behavior in case they wear out. Fixes: 8668d8b2e67f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards") Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> --- Changes for v3: * none Changes for v2: * none --- .../boot/dts/freescale/imx8mm-kontron-bl.dts | 16 ++++++++-------- 1 file changed, 8 insertions(+), 8 deletions(-) diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts index 5fd2e45258b11..ee93db11c0d06 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts @@ -292,19 +292,19 @@ MX8MM_IOMUXC_SPDIF_RX_PWM2_OUT 0x19 pinctrl_uart1: uart1grp { fsl,pins = < - MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX 0x140 - MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX 0x140 - MX8MM_IOMUXC_SAI2_RXD0_UART1_DCE_RTS_B 0x140 - MX8MM_IOMUXC_SAI2_TXFS_UART1_DCE_CTS_B 0x140 + MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX 0x0 + MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX 0x0 + MX8MM_IOMUXC_SAI2_RXD0_UART1_DCE_RTS_B 0x0 + MX8MM_IOMUXC_SAI2_TXFS_UART1_DCE_CTS_B 0x0 >; }; pinctrl_uart2: uart2grp { fsl,pins = < - MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX 0x140 - MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX 0x140 - MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B 0x140 - MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B 0x140 + MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX 0x0 + MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX 0x0 + MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B 0x0 + MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B 0x0 >; }; -- 2.43.0 ^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH v4 05/12] arm64: dts: imx8mm-kontron: Disable pull resistors for SD card signals on BL OSM-S board 2024-01-08 8:48 [PATCH v4 00/12] arm64: dts: imx8mm-kontron: DT updates Frieder Schrempf ` (3 preceding siblings ...) 2024-01-08 8:49 ` [PATCH v4 04/12] arm64: dts: imx8mm-kontron: Disable pullups for onboard UART signals on BL board Frieder Schrempf @ 2024-01-08 8:49 ` Frieder Schrempf 2024-01-08 8:49 ` [PATCH v4 06/12] arm64: dts: imx8mm-kontron: Disable pull resistors for SD card signals on BL board Frieder Schrempf ` (7 subsequent siblings) 12 siblings, 0 replies; 14+ messages in thread From: Frieder Schrempf @ 2024-01-08 8:49 UTC (permalink / raw) To: Conor Dooley, devicetree, Frieder Schrempf, Krzysztof Kozlowski, linux-arm-kernel, linux-kernel, Rob Herring, Sascha Hauer, Shawn Guo Cc: Fabio Estevam, NXP Linux Team, Pengutronix Kernel Team From: Frieder Schrempf <frieder.schrempf@kontron.de> Some signals have external pullup resistors on the board and don't need the internal ones to be enabled. Due to silicon errata ERR050080 let's disable the internal pull resistors whererever possible and prevent any unwanted behavior in case they wear out. Fixes: de9618e84f76 ("arm64: dts: Add support for Kontron SL/BL i.MX8MM OSM-S") Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> --- Changes for v3: * none Changes for v2: * none --- .../dts/freescale/imx8mm-kontron-bl-osm-s.dts | 18 +++++++++--------- 1 file changed, 9 insertions(+), 9 deletions(-) diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts index 1dd03ef0a7835..d9fa0deea7002 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts @@ -337,40 +337,40 @@ MX8MM_IOMUXC_NAND_CE1_B_GPIO3_IO2 0x19 pinctrl_usdhc2: usdhc2grp { fsl,pins = < - MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x190 + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x90 MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0 MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0 MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0 MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0 MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0 - MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x019 - MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 + MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x19 + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xd0 >; }; pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp { fsl,pins = < - MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x194 + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x94 MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4 MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4 MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4 MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4 MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4 - MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x019 - MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 + MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x19 + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xd0 >; }; pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp { fsl,pins = < - MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x196 + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x96 MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6 MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6 MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6 MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6 MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6 - MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x019 - MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 + MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x19 + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xd0 >; }; }; -- 2.43.0 ^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH v4 06/12] arm64: dts: imx8mm-kontron: Disable pull resistors for SD card signals on BL board 2024-01-08 8:48 [PATCH v4 00/12] arm64: dts: imx8mm-kontron: DT updates Frieder Schrempf ` (4 preceding siblings ...) 2024-01-08 8:49 ` [PATCH v4 05/12] arm64: dts: imx8mm-kontron: Disable pull resistors for SD card signals on BL OSM-S board Frieder Schrempf @ 2024-01-08 8:49 ` Frieder Schrempf 2024-01-08 8:49 ` [PATCH v4 07/12] arm64: dts: imx8mm-kontron: Fix interrupt for RTC on OSM-S i.MX8MM module Frieder Schrempf ` (6 subsequent siblings) 12 siblings, 0 replies; 14+ messages in thread From: Frieder Schrempf @ 2024-01-08 8:49 UTC (permalink / raw) To: Conor Dooley, devicetree, Frieder Schrempf, Krzysztof Kozlowski, linux-arm-kernel, linux-kernel, Rob Herring, Sascha Hauer, Shawn Guo Cc: Fabio Estevam, Krzysztof Kozlowski, NXP Linux Team, Pengutronix Kernel Team From: Frieder Schrempf <frieder.schrempf@kontron.de> Some signals have external pullup resistors on the board and don't need the internal ones to be enabled. Due to silicon errata ERR050080 let's disable the internal pull resistors whererever possible and prevent any unwanted behavior in case they wear out. Fixes: 8668d8b2e67f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards") Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> --- Changes for v3: * none Changes for v2: * none --- .../boot/dts/freescale/imx8mm-kontron-bl.dts | 18 +++++++++--------- 1 file changed, 9 insertions(+), 9 deletions(-) diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts index ee93db11c0d06..aab8e24216501 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts @@ -316,40 +316,40 @@ MX8MM_IOMUXC_NAND_CE1_B_GPIO3_IO2 0x19 pinctrl_usdhc2: usdhc2grp { fsl,pins = < - MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x190 + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x90 MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0 MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0 MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0 MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0 MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0 - MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x019 - MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 + MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x19 + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xd0 >; }; pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp { fsl,pins = < - MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x194 + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x94 MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4 MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4 MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4 MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4 MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4 - MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x019 - MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 + MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x19 + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xd0 >; }; pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp { fsl,pins = < - MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x196 + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x96 MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6 MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6 MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6 MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6 MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6 - MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x019 - MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 + MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x19 + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xd0 >; }; }; -- 2.43.0 ^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH v4 07/12] arm64: dts: imx8mm-kontron: Fix interrupt for RTC on OSM-S i.MX8MM module 2024-01-08 8:48 [PATCH v4 00/12] arm64: dts: imx8mm-kontron: DT updates Frieder Schrempf ` (5 preceding siblings ...) 2024-01-08 8:49 ` [PATCH v4 06/12] arm64: dts: imx8mm-kontron: Disable pull resistors for SD card signals on BL board Frieder Schrempf @ 2024-01-08 8:49 ` Frieder Schrempf 2024-01-08 8:49 ` [PATCH v4 08/12] arm64: dts: imx8mm-kontron: Fix OSM-S devicetrees to match latest hardware Frieder Schrempf ` (5 subsequent siblings) 12 siblings, 0 replies; 14+ messages in thread From: Frieder Schrempf @ 2024-01-08 8:49 UTC (permalink / raw) To: Conor Dooley, devicetree, Frieder Schrempf, Krzysztof Kozlowski, linux-arm-kernel, linux-kernel, Rob Herring, Sascha Hauer, Shawn Guo Cc: Fabio Estevam, NXP Linux Team, Pengutronix Kernel Team From: Frieder Schrempf <frieder.schrempf@kontron.de> The level of the interrupt signal is active low instead. Fix this. Fixes: de9618e84f76 ("arm64: dts: Add support for Kontron SL/BL i.MX8MM OSM-S") Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> --- Changes for v3: * none Changes for v2: * none --- arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi index 3e7db968f7e64..60abcb636cedf 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi @@ -210,7 +210,7 @@ rv3028: rtc@52 { reg = <0x52>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_rtc>; - interrupts-extended = <&gpio4 1 IRQ_TYPE_LEVEL_HIGH>; + interrupts-extended = <&gpio4 1 IRQ_TYPE_LEVEL_LOW>; trickle-diode-disable; }; }; -- 2.43.0 ^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH v4 08/12] arm64: dts: imx8mm-kontron: Fix OSM-S devicetrees to match latest hardware 2024-01-08 8:48 [PATCH v4 00/12] arm64: dts: imx8mm-kontron: DT updates Frieder Schrempf ` (6 preceding siblings ...) 2024-01-08 8:49 ` [PATCH v4 07/12] arm64: dts: imx8mm-kontron: Fix interrupt for RTC on OSM-S i.MX8MM module Frieder Schrempf @ 2024-01-08 8:49 ` Frieder Schrempf 2024-01-08 8:49 ` [PATCH v4 09/12] arm64: dts: imx8mm-kontron: Disable uneffective PUE bit in SDIO IOMUX Frieder Schrempf ` (4 subsequent siblings) 12 siblings, 0 replies; 14+ messages in thread From: Frieder Schrempf @ 2024-01-08 8:49 UTC (permalink / raw) To: Conor Dooley, devicetree, Frieder Schrempf, Krzysztof Kozlowski, linux-arm-kernel, linux-kernel, Rob Herring, Sascha Hauer, Shawn Guo Cc: Fabio Estevam, NXP Linux Team, Pengutronix Kernel Team From: Frieder Schrempf <frieder.schrempf@kontron.de> The current state of the devicetree for the i.MX8MM OSM-S and the BL baseboard reflects deprecated prototype hardware. Update the board description to match the latest hardware revision. As the old hardware is not available anymore, was only produced in very small quantities and was broken in some ways, we can safely fixup the original devicetree. Fixes: de9618e84f76 ("arm64: dts: Add support for Kontron SL/BL i.MX8MM OSM-S") Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> --- Changes for v3: * none Changes for v2: * none --- .../dts/freescale/imx8mm-kontron-bl-osm-s.dts | 64 ++++++++++++------- 1 file changed, 41 insertions(+), 23 deletions(-) diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts index d9fa0deea7002..7c5586efccc59 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts @@ -30,18 +30,18 @@ leds { led1 { label = "led1"; - gpios = <&gpio1 12 GPIO_ACTIVE_LOW>; + gpios = <&gpio1 5 GPIO_ACTIVE_LOW>; linux,default-trigger = "heartbeat"; }; led2 { label = "led2"; - gpios = <&gpio1 13 GPIO_ACTIVE_LOW>; + gpios = <&gpio3 8 GPIO_ACTIVE_LOW>; }; led3 { label = "led3"; - gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; + gpios = <&gpio3 7 GPIO_ACTIVE_LOW>; }; }; @@ -54,7 +54,7 @@ reg_rst_eth2: regulator-rst-eth2 { compatible = "regulator-fixed"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usb_eth2>; - gpio = <&gpio3 2 GPIO_ACTIVE_HIGH>; + gpio = <&gpio1 1 GPIO_ACTIVE_HIGH>; enable-active-high; regulator-always-on; regulator-name = "rst-usb-eth2"; @@ -91,7 +91,7 @@ can@0 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_can>; clocks = <&osc_can>; - interrupts-extended = <&gpio4 28 IRQ_TYPE_LEVEL_LOW>; + interrupts-extended = <&gpio5 1 IRQ_TYPE_LEVEL_LOW>; /* * Limit the SPI clock to 15 MHz to prevent issues * with corrupted data due to chip errata. @@ -118,7 +118,7 @@ eeram@0 { &fec1 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_enet>; - phy-connection-type = "rgmii-rxid"; + phy-connection-type = "rgmii-id"; phy-handle = <ðphy>; status = "okay"; @@ -127,10 +127,11 @@ mdio { #size-cells = <0>; ethphy: ethernet-phy@0 { + compatible = "ethernet-phy-id4f51.e91b", + "ethernet-phy-ieee802.3-c22"; reg = <0>; - reset-assert-us = <1>; - reset-deassert-us = <15000>; - reset-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>; + reset-assert-us = <10000>; + reset-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>; }; }; }; @@ -153,11 +154,24 @@ &gpio5 { "", "", "", "", "", "", "", ""; }; +&i2c3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; + + usb-hub@2c { + compatible = "microchip,usb2514b"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb_hub>; + reg = <0x2c>; + non-removable-ports = <0>, <3>; + reset-gpios = <&gpio5 2 GPIO_ACTIVE_LOW>; + }; +}; + &i2c4 { - clock-frequency = <100000>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_i2c4>; - status = "okay"; }; &pwm2 { @@ -196,13 +210,13 @@ &usbotg2 { status = "okay"; usb1@1 { - compatible = "usb424,9514"; + compatible = "usb424,2514"; reg = <1>; #address-cells = <1>; #size-cells = <0>; usbnet: ethernet@1 { - compatible = "usb424,ec00"; + compatible = "usbb95,772b"; reg = <1>; local-mac-address = [ 00 00 00 00 00 00 ]; }; @@ -223,7 +237,7 @@ &usdhc2 { &iomuxc { pinctrl_can: cangrp { fsl,pins = < - MX8MM_IOMUXC_SAI3_RXFS_GPIO4_IO28 0x19 + MX8MM_IOMUXC_SAI3_TXD_GPIO5_IO1 0x19 >; }; @@ -261,27 +275,24 @@ MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91 MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91 MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f - MX8MM_IOMUXC_GPIO1_IO01_GPIO1_IO1 0x19 /* PHY RST */ - MX8MM_IOMUXC_GPIO1_IO05_GPIO1_IO5 0x19 /* ETH IRQ */ + MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x19 /* PHY RST */ >; }; pinctrl_gpio_led: gpioledgrp { fsl,pins = < - MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12 0x19 - MX8MM_IOMUXC_GPIO1_IO13_GPIO1_IO13 0x19 - MX8MM_IOMUXC_GPIO1_IO14_GPIO1_IO14 0x19 + MX8MM_IOMUXC_GPIO1_IO05_GPIO1_IO5 0x19 + MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x19 + MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x19 >; }; pinctrl_gpio1: gpio1grp { fsl,pins = < - MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x19 - MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x19 + MX8MM_IOMUXC_GPIO1_IO01_GPIO1_IO1 0x19 MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x19 MX8MM_IOMUXC_GPIO1_IO11_GPIO1_IO11 0x19 MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6 0x19 - MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x19 MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10 0x19 >; }; @@ -292,6 +303,13 @@ MX8MM_IOMUXC_SAI3_MCLK_GPIO5_IO2 0x19 >; }; + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x40000083 + MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x40000083 + >; + }; + pinctrl_i2c4: i2c4grp { fsl,pins = < MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL 0x40000083 @@ -331,7 +349,7 @@ MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B 0x0 pinctrl_usb_eth2: usbeth2grp { fsl,pins = < - MX8MM_IOMUXC_NAND_CE1_B_GPIO3_IO2 0x19 + MX8MM_IOMUXC_GPIO1_IO01_GPIO1_IO1 0x19 >; }; -- 2.43.0 ^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH v4 09/12] arm64: dts: imx8mm-kontron: Disable uneffective PUE bit in SDIO IOMUX 2024-01-08 8:48 [PATCH v4 00/12] arm64: dts: imx8mm-kontron: DT updates Frieder Schrempf ` (7 preceding siblings ...) 2024-01-08 8:49 ` [PATCH v4 08/12] arm64: dts: imx8mm-kontron: Fix OSM-S devicetrees to match latest hardware Frieder Schrempf @ 2024-01-08 8:49 ` Frieder Schrempf 2024-01-08 8:49 ` [PATCH v4 10/12] arm64: dts: imx8mm-kontron: Remove useless trickle-diode-disable from RTC node Frieder Schrempf ` (3 subsequent siblings) 12 siblings, 0 replies; 14+ messages in thread From: Frieder Schrempf @ 2024-01-08 8:49 UTC (permalink / raw) To: Conor Dooley, devicetree, Krzysztof Kozlowski, linux-arm-kernel, linux-kernel, Rob Herring, Sascha Hauer, Shawn Guo Cc: Frieder Schrempf, Fabio Estevam, NXP Linux Team, Pengutronix Kernel Team From: Frieder Schrempf <frieder.schrempf@kontron.de> The PUE bit is only effective if the PE bit is also set. To avoid confusion, disable the PUE bit if it is not needed. Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> --- Changes for v3: * none Changes for v2: * none --- arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts index 7c5586efccc59..12f786a72fbd5 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts @@ -362,7 +362,7 @@ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0 MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0 MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0 MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x19 - MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xd0 + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x90 >; }; @@ -375,7 +375,7 @@ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4 MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4 MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4 MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x19 - MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xd0 + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x90 >; }; @@ -388,7 +388,7 @@ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6 MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6 MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6 MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x19 - MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xd0 + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x90 >; }; }; -- 2.43.0 ^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH v4 10/12] arm64: dts: imx8mm-kontron: Remove useless trickle-diode-disable from RTC node 2024-01-08 8:48 [PATCH v4 00/12] arm64: dts: imx8mm-kontron: DT updates Frieder Schrempf ` (8 preceding siblings ...) 2024-01-08 8:49 ` [PATCH v4 09/12] arm64: dts: imx8mm-kontron: Disable uneffective PUE bit in SDIO IOMUX Frieder Schrempf @ 2024-01-08 8:49 ` Frieder Schrempf 2024-01-08 8:49 ` [PATCH v4 11/12] arm64: dts: imx8mm-kontron: Add I2C EEPROM on OSM-S Kontron i.MX8MM Frieder Schrempf ` (2 subsequent siblings) 12 siblings, 0 replies; 14+ messages in thread From: Frieder Schrempf @ 2024-01-08 8:49 UTC (permalink / raw) To: Conor Dooley, devicetree, Krzysztof Kozlowski, linux-arm-kernel, linux-kernel, Rob Herring, Sascha Hauer, Shawn Guo Cc: Frieder Schrempf, Fabio Estevam, NXP Linux Team, Pengutronix Kernel Team From: Frieder Schrempf <frieder.schrempf@kontron.de> The RV3028 driver doesn't use this property. Remove it. Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> --- Changes for v3: * none Changes for v2: * none --- arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi | 1 - 1 file changed, 1 deletion(-) diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi index 60abcb636cedf..b161b0c85d61e 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi @@ -211,7 +211,6 @@ rv3028: rtc@52 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_rtc>; interrupts-extended = <&gpio4 1 IRQ_TYPE_LEVEL_LOW>; - trickle-diode-disable; }; }; -- 2.43.0 ^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH v4 11/12] arm64: dts: imx8mm-kontron: Add I2C EEPROM on OSM-S Kontron i.MX8MM 2024-01-08 8:48 [PATCH v4 00/12] arm64: dts: imx8mm-kontron: DT updates Frieder Schrempf ` (9 preceding siblings ...) 2024-01-08 8:49 ` [PATCH v4 10/12] arm64: dts: imx8mm-kontron: Remove useless trickle-diode-disable from RTC node Frieder Schrempf @ 2024-01-08 8:49 ` Frieder Schrempf 2024-01-08 8:49 ` [PATCH v4 12/12] arm64: dts: imx8mm-kontron: Refactor devicetree for OSM-S module and board Frieder Schrempf 2024-02-01 7:42 ` [PATCH v4 00/12] arm64: dts: imx8mm-kontron: DT updates Shawn Guo 12 siblings, 0 replies; 14+ messages in thread From: Frieder Schrempf @ 2024-01-08 8:49 UTC (permalink / raw) To: Conor Dooley, devicetree, Krzysztof Kozlowski, linux-arm-kernel, linux-kernel, Rob Herring, Sascha Hauer, Shawn Guo Cc: Frieder Schrempf, Fabio Estevam, NXP Linux Team, Pengutronix Kernel Team From: Frieder Schrempf <frieder.schrempf@kontron.de> There is an EEPROM on the SoM module. Add it to the description. Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> --- Changes for v3: * none Changes for v2: * none --- arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi index b161b0c85d61e..6b9058fc53332 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi @@ -205,6 +205,14 @@ reg_nvcc_sd: LDO5 { }; }; + eeprom: eeprom@50 { + compatible = "atmel,24c64"; + reg = <0x50>; + address-width = <16>; + pagesize = <32>; + size = <8192>; + }; + rv3028: rtc@52 { compatible = "microcrystal,rv3028"; reg = <0x52>; -- 2.43.0 ^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH v4 12/12] arm64: dts: imx8mm-kontron: Refactor devicetree for OSM-S module and board 2024-01-08 8:48 [PATCH v4 00/12] arm64: dts: imx8mm-kontron: DT updates Frieder Schrempf ` (10 preceding siblings ...) 2024-01-08 8:49 ` [PATCH v4 11/12] arm64: dts: imx8mm-kontron: Add I2C EEPROM on OSM-S Kontron i.MX8MM Frieder Schrempf @ 2024-01-08 8:49 ` Frieder Schrempf 2024-02-01 7:42 ` [PATCH v4 00/12] arm64: dts: imx8mm-kontron: DT updates Shawn Guo 12 siblings, 0 replies; 14+ messages in thread From: Frieder Schrempf @ 2024-01-08 8:49 UTC (permalink / raw) To: Conor Dooley, devicetree, Krzysztof Kozlowski, linux-arm-kernel, linux-kernel, Rob Herring, Sascha Hauer, Shawn Guo Cc: Frieder Schrempf, Fabio Estevam, NXP Linux Team, Pengutronix Kernel Team From: Frieder Schrempf <frieder.schrempf@kontron.de> The OSM spec defines dedicated functions for all pads of the SoM. Therefore we can assume that carrier board designs stick to these definitions and extend the SoM devicetree include with matching default nodes and pinmux settings. This way we can reduce the overhead and redundancy in the carrier board devicetrees while still sticking to the policy of separating board and module description. Even if the carrier board design deviates slightly from the spec it can define its own pinmux definitions and use them as necessary or even disable unused nodes from the SoM devicetree. Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> --- Changes for v3: * Address Shawn's review comments (thanks!) Changes for v2: * none --- .../dts/freescale/imx8mm-kontron-bl-osm-s.dts | 269 +++------ .../dts/freescale/imx8mm-kontron-osm-s.dtsi | 552 +++++++++++++++++- 2 files changed, 616 insertions(+), 205 deletions(-) diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts index 12f786a72fbd5..efadfdff00af1 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts @@ -25,8 +25,6 @@ osc_can: clock-osc-can { leds { compatible = "gpio-leds"; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_gpio_led>; led1 { label = "led1"; @@ -52,24 +50,12 @@ pwm-beeper { reg_rst_eth2: regulator-rst-eth2 { compatible = "regulator-fixed"; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_usb_eth2>; gpio = <&gpio1 1 GPIO_ACTIVE_HIGH>; enable-active-high; regulator-always-on; regulator-name = "rst-usb-eth2"; }; - reg_usb1_vbus: regulator-usb1-vbus { - compatible = "regulator-fixed"; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_reg_usb1_vbus>; - gpio = <&gpio3 25 GPIO_ACTIVE_LOW>; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - regulator-name = "usb1-vbus"; - }; - reg_vdd_5v: regulator-5v { compatible = "regulator-fixed"; regulator-always-on; @@ -80,9 +66,6 @@ reg_vdd_5v: regulator-5v { }; &ecspi2 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_ecspi2>; - cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>; status = "okay"; can@0 { @@ -103,9 +86,6 @@ can@0 { }; &ecspi3 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_ecspi3>; - cs-gpios = <&gpio5 25 GPIO_ACTIVE_LOW>; status = "okay"; eeram@0 { @@ -117,7 +97,7 @@ eeram@0 { &fec1 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_enet>; + pinctrl-0 = <&pinctrl_enet_rgmii>; phy-connection-type = "rgmii-id"; phy-handle = <ðphy>; status = "okay"; @@ -136,27 +116,59 @@ ethphy: ethernet-phy@0 { }; }; +/* + * Rename SoM signals according to board usage: + * GPIO_B_0 -> DIO1_OUT + * GPIO_B_1 -> DIO2_OUT + */ &gpio1 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_gpio1>; - gpio-line-names = "", "", "", "dio1-out", "", "", "dio1-in", "dio2-out", - "dio2-in", "dio3-out", "dio3-in", "dio4-out", "", "", "", "", - "", "", "", "", "", "", "", "", - "", "", "", "", "", "", "", ""; + gpio-line-names = "", "GPIO_A_0", "", "GPIO_A_1", + "", "GPIO_A_2", "GPIO_A_3", "GPIO_A_4", + "GPIO_A_5", "GPIO_A_6", "GPIO_A_7", "DIO1_OUT", + "DIO2_OUT", "USB_A_OC#", "CAM_MCK", "USB_B_OC#", + "ETH_MDC", "ETH_MDIO", "ETH_A_(S)(R)(G)MII_TXD3", + "ETH_A_(S)(R)(G)MII_TXD2", "ETH_A_(S)(R)(G)MII_TXD1", + "ETH_A_(S)(R)(G)MII_TXD0", "ETH_A_(R)(G)MII_TX_EN(_ER)", + "ETH_A_(R)(G)MII_TX_CLK", "ETH_A_(R)(G)MII_RX_DV(_ER)", + "ETH_A_(R)(G)MII_RX_CLK", "ETH_A_(S)(R)(G)MII_RXD0", + "ETH_A_(S)(R)(G)MII_RXD1", "ETH_A_(R)(G)MII_RXD2", + "ETH_A_(R)(G)MII_RXD3"; }; -&gpio5 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_gpio5>; - gpio-line-names = "", "", "dio4-in", "", "", "", "", "", - "", "", "", "", "", "", "", "", - "", "", "", "", "", "", "", "", - "", "", "", "", "", "", "", ""; +/* + * Rename SoM signals according to board usage: + * GPIO_B_2 -> DIO3_OUT + * GPIO_B_3 -> DIO4_OUT + */ +&gpio3 { + gpio-line-names = "GPIO_C_5", "GPIO_C_4", "SDIO_B_CD#", "SDIO_B_D5", + "SDIO_B_D6", "SDIO_B_D7", "GPIO_C_0", "GPIO_C_1", + "GPIO_C_2", "GPIO_C_3", "SDIO_B_D0", "SDIO_B_D1", + "SDIO_B_D2", "SDIO_B_D3", "", "SDIO_B_D4", + "CARRIER_PWR_EN", "SDIO_B_CLK", "SDIO_B_CMD", "DIO3_OUT", + "USB_B_EN", "DIO4_OUT", "PCIe_CLKREQ#", "PCIe_A_PERST#", + "PCIe_WAKE#", "USB_A_EN"; +}; + +/* + * Rename SoM signals according to board usage: + * GPIO_B_4 -> DIO1_IN + * GPIO_B_5 -> DIO2_IN + * GPIO_B_6 -> DIO3_IN + * GPIO_B_7 -> DIO4_IN + */ +&gpio4 { + gpio-line-names = "GPIO_C_7", "", "I2S_A_DATA_IN", "I2S_B_DATA_IN", + "DIO1_IN", "BOOT_SEL0#", "BOOT_SEL1#", "", + "", "", "I2S_LRCLK", "I2S_BITCLK", + "I2S_A_DATA_OUT", "I2S_B_DATA_OUT", "DIO2_IN", "DIO3_IN", + "DIO4_IN", "SPI_A_/WP_(IO2)", "SPI_A_/HOLD_(IO3)", "GPIO_C_6", + "I2S_MCLK", "UART_A_TX", "UART_A_RX", "UART_A_CTS", + "UART_A_RTS", "", "", "", + "PCIe_SM_ALERT", "UART_B_RTS", "UART_B_CTS", "UART_B_RX"; }; &i2c3 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c3>; status = "okay"; usb-hub@2c { @@ -169,27 +181,28 @@ usb-hub@2c { }; }; -&i2c4 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c4>; -}; - &pwm2 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_pwm2>; status = "okay"; }; +®_usb2_vbus { + status = "disabled"; +}; + +®_usdhc2_vcc { + status = "disabled"; +}; + +®_usdhc3_vcc { + status = "disabled"; +}; + &uart1 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart1>; uart-has-rtscts; status = "okay"; }; &uart2 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart2>; linux,rs485-enabled-at-boot-time; uart-has-rtscts; status = "okay"; @@ -197,8 +210,6 @@ &uart2 { &usbotg1 { dr_mode = "otg"; - disable-over-current; - vbus-supply = <®_usb1_vbus>; status = "okay"; }; @@ -209,6 +220,9 @@ &usbotg2 { #size-cells = <0>; status = "okay"; + /* VBUS is controlled by the hub */ + /delete-property/ vbus-supply; + usb1@1 { compatible = "usb424,2514"; reg = <1>; @@ -224,171 +238,20 @@ usbnet: ethernet@1 { }; &usdhc2 { - pinctrl-names = "default", "state_100mhz", "state_200mhz"; - pinctrl-0 = <&pinctrl_usdhc2>; - pinctrl-1 = <&pinctrl_usdhc2_100mhz>; - pinctrl-2 = <&pinctrl_usdhc2_200mhz>; vmmc-supply = <®_vdd_3v3>; - vqmmc-supply = <®_nvcc_sd>; - cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>; status = "okay"; }; &iomuxc { pinctrl_can: cangrp { fsl,pins = < - MX8MM_IOMUXC_SAI3_TXD_GPIO5_IO1 0x19 - >; - }; - - pinctrl_ecspi2: ecspi2grp { - fsl,pins = < - MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO 0x82 - MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0x82 - MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0x82 - MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13 0x19 - >; - }; - - pinctrl_ecspi3: ecspi3grp { - fsl,pins = < - MX8MM_IOMUXC_UART2_RXD_ECSPI3_MISO 0x82 - MX8MM_IOMUXC_UART1_TXD_ECSPI3_MOSI 0x82 - MX8MM_IOMUXC_UART1_RXD_ECSPI3_SCLK 0x82 - MX8MM_IOMUXC_UART2_TXD_GPIO5_IO25 0x19 - >; - }; - - pinctrl_enet: enetgrp { - fsl,pins = < - MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x3 - MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x3 - MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f - MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f - MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f - MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f - MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91 - MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91 - MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91 - MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91 - MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f - MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91 - MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91 - MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f - MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x19 /* PHY RST */ - >; - }; - - pinctrl_gpio_led: gpioledgrp { - fsl,pins = < - MX8MM_IOMUXC_GPIO1_IO05_GPIO1_IO5 0x19 - MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x19 - MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x19 - >; - }; - - pinctrl_gpio1: gpio1grp { - fsl,pins = < - MX8MM_IOMUXC_GPIO1_IO01_GPIO1_IO1 0x19 - MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x19 - MX8MM_IOMUXC_GPIO1_IO11_GPIO1_IO11 0x19 - MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6 0x19 - MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10 0x19 - >; - }; - - pinctrl_gpio5: gpio5grp { - fsl,pins = < - MX8MM_IOMUXC_SAI3_MCLK_GPIO5_IO2 0x19 - >; - }; - - pinctrl_i2c3: i2c3grp { - fsl,pins = < - MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x40000083 - MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x40000083 - >; - }; - - pinctrl_i2c4: i2c4grp { - fsl,pins = < - MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL 0x40000083 - MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA 0x40000083 - >; - }; - - pinctrl_pwm2: pwm2grp { - fsl,pins = < - MX8MM_IOMUXC_SPDIF_RX_PWM2_OUT 0x19 - >; - }; - - pinctrl_reg_usb1_vbus: regusb1vbusgrp { - fsl,pins = < - MX8MM_IOMUXC_SAI5_MCLK_GPIO3_IO25 0x19 - >; - }; - - pinctrl_uart1: uart1grp { - fsl,pins = < - MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX 0x0 - MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX 0x0 - MX8MM_IOMUXC_SAI2_RXD0_UART1_DCE_RTS_B 0x0 - MX8MM_IOMUXC_SAI2_TXFS_UART1_DCE_CTS_B 0x0 - >; - }; - - pinctrl_uart2: uart2grp { - fsl,pins = < - MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX 0x0 - MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX 0x0 - MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B 0x0 - MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B 0x0 - >; - }; - - pinctrl_usb_eth2: usbeth2grp { - fsl,pins = < - MX8MM_IOMUXC_GPIO1_IO01_GPIO1_IO1 0x19 - >; - }; - - pinctrl_usdhc2: usdhc2grp { - fsl,pins = < - MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x90 - MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0 - MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0 - MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0 - MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0 - MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0 - MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x19 - MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x90 - >; - }; - - pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp { - fsl,pins = < - MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x94 - MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4 - MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4 - MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4 - MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4 - MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4 - MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x19 - MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x90 + MX8MM_IOMUXC_SAI3_TXD_GPIO5_IO1 0x19 /* SDIO_B_PWR_EN */ >; }; - pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp { + pinctrl_usb_hub: usbhubgrp { fsl,pins = < - MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x96 - MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6 - MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6 - MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6 - MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6 - MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6 - MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x19 - MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x90 + MX8MM_IOMUXC_SAI3_MCLK_GPIO5_IO2 0x19 /* SDIO_B_WP */ >; }; }; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi index 6b9058fc53332..663ae52b48526 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi @@ -3,6 +3,7 @@ * Copyright (C) 2022 Kontron Electronics GmbH */ +#include <dt-bindings/gpio/gpio.h> #include <dt-bindings/interrupt-controller/irq.h> #include "imx8mm.dtsi" @@ -28,6 +29,73 @@ memory@40000000 { chosen { stdout-path = &uart3; }; + + reg_vdd_carrier: regulator-vdd-carrier { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_vdd_carrier>; + gpio = <&gpio3 16 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + regulator-name = "VDD_CARRIER"; + + regulator-state-standby { + regulator-on-in-suspend; + }; + + regulator-state-mem { + regulator-off-in-suspend; + }; + + regulator-state-disk { + regulator-off-in-suspend; + }; + }; + + reg_usb1_vbus: regulator-usb1-vbus { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_usb1_vbus>; + enable-active-high; + gpio = <&gpio3 25 GPIO_ACTIVE_HIGH>; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-name = "VBUS_USB1"; + }; + + reg_usb2_vbus: regulator-usb2-vbus { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_usb2_vbus>; + enable-active-high; + gpio = <&gpio3 20 GPIO_ACTIVE_HIGH>; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-name = "VBUS_USB2"; + }; + + reg_usdhc2_vcc: regulator-usdhc2-vcc { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_usdhc2_vcc>; + enable-active-high; + gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "VCC_SDIO_A"; + }; + + reg_usdhc3_vcc: regulator-usdhc3-vcc { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_usdhc3_vcc>; + enable-active-high; + gpio = <&gpio5 1 GPIO_ACTIVE_HIGH>; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "VCC_SDIO_B"; + }; }; &A53_0 { @@ -96,6 +164,79 @@ partition@1f0000 { }; }; +&ecspi2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi2>, <&pinctrl_ecspi2_gpio>; + cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>; +}; + +&ecspi3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi3>; + cs-gpios = <&gpio5 25 GPIO_ACTIVE_LOW>; +}; + +&gpio1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio1>; + gpio-line-names = "", "GPIO_A_0", "", "GPIO_A_1", + "", "GPIO_A_2", "GPIO_A_3", "GPIO_A_4", + "GPIO_A_5", "GPIO_A_6", "GPIO_A_7", "GPIO_B_0", + "GPIO_B_1", "USB_A_OC#", "CAM_MCK", "USB_B_OC#", + "ETH_MDC", "ETH_MDIO", "ETH_A_(S)(R)(G)MII_TXD3", + "ETH_A_(S)(R)(G)MII_TXD2", "ETH_A_(S)(R)(G)MII_TXD1", + "ETH_A_(S)(R)(G)MII_TXD0", "ETH_A_(R)(G)MII_TX_EN(_ER)", + "ETH_A_(R)(G)MII_TX_CLK", "ETH_A_(R)(G)MII_RX_DV(_ER)", + "ETH_A_(R)(G)MII_RX_CLK", "ETH_A_(S)(R)(G)MII_RXD0", + "ETH_A_(S)(R)(G)MII_RXD1", "ETH_A_(R)(G)MII_RXD2", + "ETH_A_(R)(G)MII_RXD3"; +}; + +&gpio2 { + gpio-line-names = "", "", "", "", + "", "", "", "", + "", "", "", "", + "SDIO_A_CD#", "SDIO_A_CLK", "SDIO_A_CMD", "SDIO_A_D0", + "SDIO_A_D1", "SDIO_A_D2", "SDIO_A_D3", "SDIO_A_PWR_EN", + "SDIO_A_WP"; +}; + +&gpio3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio3>; + gpio-line-names = "GPIO_C_5", "GPIO_C_4", "SDIO_B_CD#", "SDIO_B_D5", + "SDIO_B_D6", "SDIO_B_D7", "GPIO_C_0", "GPIO_C_1", + "GPIO_C_2", "GPIO_C_3", "SDIO_B_D0", "SDIO_B_D1", + "SDIO_B_D2", "SDIO_B_D3", "", "SDIO_B_D4", + "CARRIER_PWR_EN", "SDIO_B_CLK", "SDIO_B_CMD", "GPIO_B_2", + "USB_B_EN", "GPIO_B_3", "PCIe_CLKREQ#", "PCIe_A_PERST#", + "PCIe_WAKE#", "USB_A_EN"; +}; + +&gpio4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio4>; + gpio-line-names = "GPIO_C_7", "", "I2S_A_DATA_IN", "I2S_B_DATA_IN", + "GPIO_B_4", "BOOT_SEL0#", "BOOT_SEL1#", "", + "", "", "I2S_LRCLK", "I2S_BITCLK", + "I2S_A_DATA_OUT", "I2S_B_DATA_OUT", "GPIO_B_5", "GPIO_B_6", + "GPIO_B_7", "SPI_A_/WP_(IO2)", "SPI_A_/HOLD_(IO3)", "GPIO_C_6", + "I2S_MCLK", "UART_A_TX", "UART_A_RX", "UART_A_CTS", + "UART_A_RTS", "", "", "", + "PCIe_SM_ALERT", "UART_B_RTS", "UART_B_CTS", "UART_B_RX"; +}; + +&gpio5 { + gpio-line-names = "UART_B_TX", "SDIO_B_PWR_EN", "SDIO_B_WP", "PWM_2", + "PWM_1", "PWM_0", "", "", + "", "", "SPI_A_SCK", "SPI_A_SDO_(IO1)", + "SPI_A_SCK", "SPI_A_CS0#", "", "", + "I2C_A_SCL", "I2C_A_SDA", "I2C_B_SCL", "I2C_B_SDA", + "PCIe_SMCLK", "PCIe_SMDAT", "SPI_B_SCK", "SPI_B_SDO", + "SPI_B_SDI", "SPI_B_CS0#", "UART_CON_RX", "UART_CON_TX", + "UART_C_RX", "UART_C_TX"; +}; + &i2c1 { clock-frequency = <400000>; pinctrl-names = "default"; @@ -222,12 +363,69 @@ rv3028: rtc@52 { }; }; +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; +}; + +&i2c3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; +}; + +&i2c4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c4>; +}; + +&pwm1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm1>; +}; + +&pwm2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm2>; +}; + +&pwm3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm3>; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; +}; + &uart3 { /* console */ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_uart3>; status = "okay"; }; +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4>; +}; + +&usbotg1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb1>; + vbus-supply = <®_usb1_vbus>; +}; + +&usbotg2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb2>; + vbus-supply = <®_usb2_vbus>; +}; + &usdhc1 { pinctrl-names = "default", "state_100mhz", "state_200mhz"; pinctrl-0 = <&pinctrl_usdhc1>; @@ -240,6 +438,26 @@ &usdhc1 { status = "okay"; }; +&usdhc2 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; + pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>; + pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>; + vmmc-supply = <®_usdhc2_vcc>; + vqmmc-supply = <®_nvcc_sd>; + cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>; +}; + +&usdhc3 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc3>, <&pinctrl_usdhc3_gpio>; + pinctrl-1 = <&pinctrl_usdhc3_100mhz>, <&pinctrl_usdhc3_gpio>; + pinctrl-2 = <&pinctrl_usdhc3_200mhz>, <&pinctrl_usdhc3_gpio>; + vmmc-supply = <®_usdhc3_vcc>; + vqmmc-supply = <®_nvcc_sd>; + cd-gpios = <&gpio3 2 GPIO_ACTIVE_LOW>; +}; + &wdog1 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_wdog>; @@ -248,6 +466,12 @@ &wdog1 { }; &iomuxc { + pinctrl_csi_mck: csimckgrp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO14_CCMSRCGPCMIX_CLKO1 0x59 /* CAM_MCK */ + >; + }; + pinctrl_ecspi1: ecspi1grp { fsl,pins = < MX8MM_IOMUXC_ECSPI1_MISO_ECSPI1_MISO 0x82 @@ -257,6 +481,106 @@ MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9 0x19 >; }; + pinctrl_ecspi2: ecspi2grp { + fsl,pins = < + MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO 0x82 /* SPI_A_SDI_(IO0) */ + MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0x82 /* SPI_A_SDO_(IO1) */ + MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0x82 /* SPI_A_SCK */ + MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13 0x19 /* SPI_A_CS0# */ + >; + }; + + pinctrl_ecspi2_gpio: ecspi2gpiogrp { + fsl,pins = < + MX8MM_IOMUXC_SAI1_TXD5_GPIO4_IO17 0x19 /* SPI_A_/WP_(IO2) */ + MX8MM_IOMUXC_SAI1_TXD6_GPIO4_IO18 0x19 /* SPI_A_/HOLD_(IO3) */ + >; + }; + + pinctrl_ecspi3: ecspi3grp { + fsl,pins = < + MX8MM_IOMUXC_UART2_RXD_ECSPI3_MISO 0x82 /* SPI_B_SDI */ + MX8MM_IOMUXC_UART1_TXD_ECSPI3_MOSI 0x82 /* SPI_B_SDO */ + MX8MM_IOMUXC_UART1_RXD_ECSPI3_SCLK 0x82 /* SPI_B_SCK */ + MX8MM_IOMUXC_UART2_TXD_GPIO5_IO25 0x19 /* SPI_B_CS0# */ + >; + }; + + pinctrl_enet_rgmii: enetrgmiigrp { + fsl,pins = < + MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x03 /* ETH_MDC */ + MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x03 /* ETH_MDIO */ + MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f /* ETH_A_(S)(R)(G)MII_TXD3 */ + MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f /* ETH_A_(S)(R)(G)MII_TXD2 */ + MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f /* ETH_A_(S)(R)(G)MII_TXD1 */ + MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f /* ETH_A_(S)(R)(G)MII_TXD0 */ + MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91 /* ETH_A_(R)(G)MII_RXD3 */ + MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91 /* ETH_A_(R)(G)MII_RXD2 */ + MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91 /* ETH_A_(S)(R)(G)MII_RXD1 */ + MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91 /* ETH_A_(S)(R)(G)MII_RXD0 */ + MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f /* ETH_A_(R)(G)MII_TX_CLK */ + MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91 /* ETH_A_(R)(G)MII_RX_CLK */ + MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91 /* ETH_A_(R)(G)MII_RX_DV(_ER) */ + MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f /* ETH_A_(R)(G)MII_TX_EN(_ER) */ + >; + }; + + pinctrl_enet_rmii: enetrmiigrp { + fsl,pins = < + MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x03 /* ETH_MDC */ + MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x03 /* ETH_MDIO */ + MX8MM_IOMUXC_ENET_TD2_ENET1_TX_CLK 0x4000001f /* ETH_A_(S)(R)(G)MII_TXD2 */ + MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x56 /* ETH_A_(S)(R)(G)MII_TXD1 */ + MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x56 /* ETH_A_(S)(R)(G)MII_TXD0 */ + MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x56 /* ETH_A_(S)(R)(G)MII_RXD1 */ + MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x56 /* ETH_A_(S)(R)(G)MII_RXD0 */ + MX8MM_IOMUXC_ENET_RXC_ENET1_RX_ER 0x56 /* ETH_A_(R)(G)MII_RX_CLK */ + MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x56 /* ETH_A_(R)(G)MII_RX_DV(_ER) */ + MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x56 /* ETH_A_(R)(G)MII_TX_EN(_ER) */ + >; + }; + + pinctrl_gpio1: gpio1grp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO01_GPIO1_IO1 0x19 /* GPIO_A_0 */ + MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x19 /* GPIO_A_1 */ + MX8MM_IOMUXC_GPIO1_IO05_GPIO1_IO5 0x19 /* GPIO_A_2 */ + MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6 0x19 /* GPIO_A_3 */ + MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x19 /* GPIO_A_4 */ + MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x19 /* GPIO_A_5 */ + MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x19 /* GPIO_A_6 */ + MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10 0x19 /* GPIO_A_7 */ + MX8MM_IOMUXC_GPIO1_IO11_GPIO1_IO11 0x19 /* GPIO_B_0 */ + MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12 0x19 /* GPIO_B_1 */ + >; + }; + + pinctrl_gpio3: gpio3grp { + fsl,pins = < + MX8MM_IOMUXC_NAND_ALE_GPIO3_IO0 0x19 /* GPIO_C_5 */ + MX8MM_IOMUXC_NAND_CE0_B_GPIO3_IO1 0x19 /* GPIO_C_4 */ + MX8MM_IOMUXC_NAND_DATA00_GPIO3_IO6 0x19 /* GPIO_C_0 */ + MX8MM_IOMUXC_NAND_DATA01_GPIO3_IO7 0x19 /* GPIO_C_1 */ + MX8MM_IOMUXC_NAND_DATA02_GPIO3_IO8 0x19 /* GPIO_C_2 */ + MX8MM_IOMUXC_NAND_DATA03_GPIO3_IO9 0x19 /* GPIO_C_3 */ + MX8MM_IOMUXC_SAI5_RXFS_GPIO3_IO19 0x19 /* GPIO_B_2 */ + MX8MM_IOMUXC_SAI5_RXD0_GPIO3_IO21 0x19 /* GPIO_B_3 */ + >; + }; + + pinctrl_gpio4: gpio4grp { + fsl,pins = < + MX8MM_IOMUXC_SAI1_RXFS_GPIO4_IO0 0x19 /* GPIO_C_7 */ + MX8MM_IOMUXC_SAI1_RXD2_GPIO4_IO4 0x19 /* GPIO_B_4 */ + MX8MM_IOMUXC_SAI1_RXD3_GPIO4_IO5 0x19 /* BOOT_SEL0# */ + MX8MM_IOMUXC_SAI1_RXD4_GPIO4_IO6 0x19 /* BOOT_SEL1# */ + MX8MM_IOMUXC_SAI1_TXD2_GPIO4_IO14 0x19 /* GPIO_B_5 */ + MX8MM_IOMUXC_SAI1_TXD3_GPIO4_IO15 0x19 /* GPIO_B_6 */ + MX8MM_IOMUXC_SAI1_TXD4_GPIO4_IO16 0x19 /* GPIO_B_7 */ + MX8MM_IOMUXC_SAI1_TXD7_GPIO4_IO19 0x19 /* GPIO_C_6 */ + >; + }; + pinctrl_i2c1: i2c1grp { fsl,pins = < MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x40000083 @@ -264,22 +588,149 @@ MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x40000083 >; }; + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL 0x40000083 /* I2C_A_SCL */ + MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA 0x40000083 /* I2C_A_SDA */ + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x40000083 /* I2C_B_SCL */ + MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x40000083 /* I2C_B_SDA */ + >; + }; + + pinctrl_i2c4: i2c4grp { + fsl,pins = < + MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL 0x40000083 /* PCIe_SMCLK and I2C_CAM_SCL/CSI_TX_P */ + MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA 0x40000083 /* PCIe_SMDAT and I2C_CAM_SDA/CSI_TX_N */ + >; + }; + + pinctrl_pcie: pciegrp { + fsl,pins = < + MX8MM_IOMUXC_SAI5_RXD1_GPIO3_IO22 0x19 /* PCIe_CLKREQ# */ + MX8MM_IOMUXC_SAI5_RXD2_GPIO3_IO23 0x19 /* PCIe_A_PERST# */ + MX8MM_IOMUXC_SAI5_RXD3_GPIO3_IO24 0x19 /* PCIe_WAKE# */ + MX8MM_IOMUXC_SAI3_RXFS_GPIO4_IO28 0x19 /* PCIe_SM_ALERT */ + >; + }; + pinctrl_pmic: pmicgrp { fsl,pins = < MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x141 >; }; + pinctrl_pwm1: pwm1grp { + fsl,pins = < + MX8MM_IOMUXC_SPDIF_EXT_CLK_PWM1_OUT 0x19 /* PWM_0 */ + >; + }; + + pinctrl_pwm2: pwm2grp { + fsl,pins = < + MX8MM_IOMUXC_SPDIF_RX_PWM2_OUT 0x19 /* PWM_1 */ + >; + }; + + pinctrl_pwm3: pwm3grp { + fsl,pins = < + MX8MM_IOMUXC_SPDIF_TX_PWM3_OUT 0x19 /* PWM_2 */ + >; + }; + + pinctrl_reg_usb1_vbus: regusb1vbusgrp { + fsl,pins = < + MX8MM_IOMUXC_SAI5_MCLK_GPIO3_IO25 0x19 /* USB_A_EN */ + >; + }; + + pinctrl_reg_usb2_vbus: regusb2vbusgrp { + fsl,pins = < + MX8MM_IOMUXC_SAI5_RXC_GPIO3_IO20 0x19 /* USB_B_EN */ + >; + }; + + pinctrl_reg_usdhc2_vcc: regusdhc2vccgrp { + fsl,pins = < + MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x19 /* SDIO_A_PWR_EN */ + >; + }; + + pinctrl_reg_usdhc3_vcc: regusdhc3vccgrp { + fsl,pins = < + MX8MM_IOMUXC_SAI3_TXD_GPIO5_IO1 0x19 /* SDIO_B_PWR_EN */ + >; + }; + + pinctrl_reg_vdd_carrier: regvddcarriergrp { + fsl,pins = < + MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16 0x19 /* CARRIER_PWR_EN */ + >; + }; + pinctrl_rtc: rtcgrp { fsl,pins = < MX8MM_IOMUXC_SAI1_RXC_GPIO4_IO1 0x19 >; }; + pinctrl_sai1: sai1grp { + fsl,pins = < + MX8MM_IOMUXC_SAI1_RXD0_SAI1_RX_DATA0 0xd6 /* I2S_A_DATA_IN */ + MX8MM_IOMUXC_SAI1_TXD0_SAI1_TX_DATA0 0xd6 /* I2S_A_DATA_OUT */ + MX8MM_IOMUXC_SAI1_RXD1_SAI1_RX_DATA1 0xd6 /* I2S_B_DATA_IN */ + MX8MM_IOMUXC_SAI1_TXD1_SAI1_TX_DATA1 0xd6 /* I2S_B_DATA_OUT */ + MX8MM_IOMUXC_SAI1_MCLK_SAI1_MCLK 0xd6 /* I2S_MCLK */ + MX8MM_IOMUXC_SAI1_TXFS_SAI1_TX_SYNC 0xd6 /* I2S_LRCLK */ + MX8MM_IOMUXC_SAI1_TXC_SAI1_TX_BCLK 0xd6 /* I2S_BITCLK */ + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX 0x0 /* UART_A_RX */ + MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX 0x0 /* UART_A_TX */ + MX8MM_IOMUXC_SAI2_RXD0_UART1_DCE_RTS_B 0x0 /* UART_A_CTS */ + MX8MM_IOMUXC_SAI2_TXFS_UART1_DCE_CTS_B 0x0 /* UART_A_RTS */ + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX 0x0 /* UART_B_RX */ + MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX 0x0 /* UART_B_TX */ + MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B 0x0 /* UART_B_CTS */ + MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B 0x0 /* UART_B_RTS */ + >; + }; + pinctrl_uart3: uart3grp { fsl,pins = < - MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX 0x140 - MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX 0x140 + MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX 0x140 /* UART_CON_RX */ + MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX 0x140 /* UART_CON_TX */ + >; + }; + + pinctrl_uart4: uart4grp { + fsl,pins = < + MX8MM_IOMUXC_UART4_RXD_UART4_DCE_RX 0x0 /* UART_C_RX */ + MX8MM_IOMUXC_UART4_TXD_UART4_DCE_TX 0x0 /* UART_C_TX */ + >; + }; + + pinctrl_usb1: usb1grp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO13_USB1_OTG_OC 0x19 /* USB_A_OC# */ + >; + }; + + pinctrl_usb2: usb2grp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO15_USB2_OTG_OC 0x19 /* USB_B_OC# */ >; }; @@ -334,6 +785,103 @@ MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x196 >; }; + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x90 /* SDIO_A_CLK */ + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0 /* SDIO_A_CMD */ + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0 /* SDIO_A_D0 */ + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0 /* SDIO_A_D1 */ + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0 /* SDIO_A_D2 */ + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0 /* SDIO_A_D3 */ + MX8MM_IOMUXC_SD2_WP_USDHC2_WP 0x400000d6 /* SDIO_A_WP */ + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x90 + >; + }; + + pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp { + fsl,pins = < + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x94 /* SDIO_A_CLK */ + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4 /* SDIO_A_CMD */ + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4 /* SDIO_A_D0 */ + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4 /* SDIO_A_D1 */ + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4 /* SDIO_A_D2 */ + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4 /* SDIO_A_D3 */ + MX8MM_IOMUXC_SD2_WP_USDHC2_WP 0x400000d6 /* SDIO_A_WP */ + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x90 + >; + }; + + pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp { + fsl,pins = < + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x96 /* SDIO_A_CLK */ + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6 /* SDIO_A_CMD */ + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6 /* SDIO_A_D0 */ + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6 /* SDIO_A_D1 */ + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6 /* SDIO_A_D2 */ + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6 /* SDIO_A_D3 */ + MX8MM_IOMUXC_SD2_WP_USDHC2_WP 0x400000d6 /* SDIO_A_WP */ + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x90 + >; + }; + + pinctrl_usdhc2_gpio: usdhc2gpiogrp { + fsl,pins = < + MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x19 /* SDIO_A_CD# */ + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x90 /* SDIO_B_CLK */ + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x90 /* SDIO_B_CMD */ + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x90 /* SDIO_B_D0 */ + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x90 /* SDIO_B_D1 */ + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x90 /* SDIO_B_D2 */ + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x90 /* SDIO_B_D3 */ + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x90 /* SDIO_B_D4 */ + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x90 /* SDIO_B_D5 */ + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x90 /* SDIO_B_D6 */ + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x90 /* SDIO_B_D7 */ + >; + }; + + pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp { + fsl,pins = < + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x94 /* SDIO_B_CLK */ + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x94 /* SDIO_B_CMD */ + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x94 /* SDIO_B_D0 */ + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x94 /* SDIO_B_D1 */ + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x94 /* SDIO_B_D2 */ + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x94 /* SDIO_B_D3 */ + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x94 /* SDIO_B_D4 */ + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x94 /* SDIO_B_D5 */ + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x94 /* SDIO_B_D6 */ + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x94 /* SDIO_B_D7 */ + >; + }; + + pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp { + fsl,pins = < + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x96 /* SDIO_B_CLK */ + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x96 /* SDIO_B_CMD */ + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x96 /* SDIO_B_D0 */ + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x96 /* SDIO_B_D1 */ + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x96 /* SDIO_B_D2 */ + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x96 /* SDIO_B_D3 */ + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x96 /* SDIO_B_D4 */ + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x96 /* SDIO_B_D5 */ + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x96 /* SDIO_B_D6 */ + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x96 /* SDIO_B_D7 */ + >; + }; + + pinctrl_usdhc3_gpio: usdhc3gpiogrp { + fsl,pins = < + MX8MM_IOMUXC_NAND_CE1_B_GPIO3_IO2 0x19 /* SDIO_B_CD# */ + MX8MM_IOMUXC_SAI3_MCLK_GPIO5_IO2 0x19 /* SDIO_B_WP */ + >; + }; + pinctrl_wdog: wdoggrp { fsl,pins = < MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6 -- 2.43.0 ^ permalink raw reply related [flat|nested] 14+ messages in thread
* Re: [PATCH v4 00/12] arm64: dts: imx8mm-kontron: DT updates 2024-01-08 8:48 [PATCH v4 00/12] arm64: dts: imx8mm-kontron: DT updates Frieder Schrempf ` (11 preceding siblings ...) 2024-01-08 8:49 ` [PATCH v4 12/12] arm64: dts: imx8mm-kontron: Refactor devicetree for OSM-S module and board Frieder Schrempf @ 2024-02-01 7:42 ` Shawn Guo 12 siblings, 0 replies; 14+ messages in thread From: Shawn Guo @ 2024-02-01 7:42 UTC (permalink / raw) To: Frieder Schrempf Cc: Conor Dooley, devicetree, Frieder Schrempf, Krzysztof Kozlowski, linux-arm-kernel, linux-kernel, Rob Herring, Sascha Hauer, Shawn Guo, Fabio Estevam, Krzysztof Kozlowski, NXP Linux Team, Pengutronix Kernel Team On Mon, Jan 08, 2024 at 09:48:57AM +0100, Frieder Schrempf wrote: > From: Frieder Schrempf <frieder.schrempf@kontron.de> > > This patchset contains several improvements and updates for the devicetrees > for the i.MX8MM modules and boards by Kontron Electronics GmbH. > > * Misc cleanups and small fixes > * OSM-S i.MX8MM module refactoring and update to latest HW revision > > Changes in v4: > * Rebase to Shawn's imx/dt64 branch > * Drop patches 1 and 2 (display support) as there are unresolved DTC warnings > and I am not sure how to resolve them at the moment. > > Changes in v3: > * Address Shawn's review comments for patch 1, 2 and 14 (thanks!) > > Changes in v2: > * Rework DSI mux GPIO logic to be compatible with overlay > * Switch from 4 to 2 DSI lanes for LVDS bridge to fix non-working display > > Frieder Schrempf (12): > arm64: dts: imx8mm-kontron: Disable pullups for I2C signals on OSM-S > i.MX8MM > arm64: dts: imx8mm-kontron: Disable pullups for I2C signals on SL/BL > i.MX8MM > arm64: dts: imx8mm-kontron: Disable pullups for onboard UART signals > on BL OSM-S board > arm64: dts: imx8mm-kontron: Disable pullups for onboard UART signals > on BL board > arm64: dts: imx8mm-kontron: Disable pull resistors for SD card signals > on BL OSM-S board > arm64: dts: imx8mm-kontron: Disable pull resistors for SD card signals > on BL board > arm64: dts: imx8mm-kontron: Fix interrupt for RTC on OSM-S i.MX8MM > module > arm64: dts: imx8mm-kontron: Fix OSM-S devicetrees to match latest > hardware > arm64: dts: imx8mm-kontron: Disable uneffective PUE bit in SDIO IOMUX > arm64: dts: imx8mm-kontron: Remove useless trickle-diode-disable from > RTC node > arm64: dts: imx8mm-kontron: Add I2C EEPROM on OSM-S Kontron i.MX8MM > arm64: dts: imx8mm-kontron: Refactor devicetree for OSM-S module and > board Applied all, thanks! ^ permalink raw reply [flat|nested] 14+ messages in thread
end of thread, other threads:[~2024-01-31 23:43 UTC | newest] Thread overview: 14+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2024-01-08 8:48 [PATCH v4 00/12] arm64: dts: imx8mm-kontron: DT updates Frieder Schrempf 2024-01-08 8:48 ` [PATCH v4 01/12] arm64: dts: imx8mm-kontron: Disable pullups for I2C signals on OSM-S i.MX8MM Frieder Schrempf 2024-01-08 8:48 ` [PATCH v4 02/12] arm64: dts: imx8mm-kontron: Disable pullups for I2C signals on SL/BL i.MX8MM Frieder Schrempf 2024-01-08 8:49 ` [PATCH v4 03/12] arm64: dts: imx8mm-kontron: Disable pullups for onboard UART signals on BL OSM-S board Frieder Schrempf 2024-01-08 8:49 ` [PATCH v4 04/12] arm64: dts: imx8mm-kontron: Disable pullups for onboard UART signals on BL board Frieder Schrempf 2024-01-08 8:49 ` [PATCH v4 05/12] arm64: dts: imx8mm-kontron: Disable pull resistors for SD card signals on BL OSM-S board Frieder Schrempf 2024-01-08 8:49 ` [PATCH v4 06/12] arm64: dts: imx8mm-kontron: Disable pull resistors for SD card signals on BL board Frieder Schrempf 2024-01-08 8:49 ` [PATCH v4 07/12] arm64: dts: imx8mm-kontron: Fix interrupt for RTC on OSM-S i.MX8MM module Frieder Schrempf 2024-01-08 8:49 ` [PATCH v4 08/12] arm64: dts: imx8mm-kontron: Fix OSM-S devicetrees to match latest hardware Frieder Schrempf 2024-01-08 8:49 ` [PATCH v4 09/12] arm64: dts: imx8mm-kontron: Disable uneffective PUE bit in SDIO IOMUX Frieder Schrempf 2024-01-08 8:49 ` [PATCH v4 10/12] arm64: dts: imx8mm-kontron: Remove useless trickle-diode-disable from RTC node Frieder Schrempf 2024-01-08 8:49 ` [PATCH v4 11/12] arm64: dts: imx8mm-kontron: Add I2C EEPROM on OSM-S Kontron i.MX8MM Frieder Schrempf 2024-01-08 8:49 ` [PATCH v4 12/12] arm64: dts: imx8mm-kontron: Refactor devicetree for OSM-S module and board Frieder Schrempf 2024-02-01 7:42 ` [PATCH v4 00/12] arm64: dts: imx8mm-kontron: DT updates Shawn Guo
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).