Re: [PATCH 2/2] arm64: dts: rockchip: rock-pi-e: fix location of snps properties

[Trevor Woerner <twoerner@gmail.com>]

On Thu 2024-01-18 @ 08:31:30 AM, Jonas Karlman wrote:
> On 2024-01-17 09:15, Jonas Karlman wrote:
> > On 2024-01-17 06:47, Trevor Woerner wrote:
> >> On Wed 2024-01-17 @ 12:38:39 PM, Chen-Yu Tsai wrote:
> >>> On Wed, Jan 17, 2024 at 4:41 AM Trevor Woerner <twoerner@gmail.com> wrote:
> >>>>
> >>>> A number of snps (Synopsys) properties are not in their correct location.
> >>>
> >>> Nope. If you read the snps,dwmac.yaml binding file, you'll see that these
> >>> properties have been deprecated. They are properties pertaining to the PHY
> >>> and should be described under the PHY node. Support for reset GPIOs on PHY
> >>> devices in phylib has been there since v4.16. The snps prefixed properties
> >>> were deprecated in v5.3.
> >>
> >> If that's the case, then the bindings and the drivers are out of sync in both
> >> U-Boot and Linux. I discovered this issue while working with older and newer
> >> revisions of the rock-pi-e board. The first three spins of the rock-pi-e have
> >> the rtl8211e PHY but the last one (v1.21) has the rtl8211f PHY.
> >>
> >> With the existing layout nothing works in U-Boot and in Linux the rtl8211e
> >> works but not the rtl8211f. With this patch both the rtl8211e and the rtl8211f
> >> PHYs work using the exact same device trees on both older and newer rock-pi-e
> >> boards in both U-Boot and Linux.
> > 
> > For linux this is probably related to the same chicken-and-egg reset
> > issue outlined at [1]. The phy is not reset before it is probed and
> > cannot be probed because it is not reset.
> > 
> > As for U-Boot the designware/gmac_rockchip ethernet driver may need some
> > adjustments to properly integrate with eth-phy uclass to properly reset
> > the phy described in a ethernet-phy node before it can be probed.
> > 
> > Following config options is disabled for rock-pi-e-rk3328 defconfig:
> > 
> > # CONFIG_DM_ETH_PHY is not set
> > # CONFIG_PHY_REALTEK is not set
> > 
> > Also the driver needs to be updated to make use eth-phy uclass for it to
> > work correctly. More similar to how the dwc_eth_qos driver works related
> > to ethernet phy.
> 
> I have just sent out a U-Boot series that fix ethernet on the v1.21
> revision of the ROCK Pi E board, see [2].

Thank you! I have tested your patches both in U-Boot and Linux and they work
perfectly.

> Would expect that ethernet also starts to work in linux with those
> patches applied to U-Boot. I only tested and verified ethernet in U-Boot.
> 
> Hopefully someone can take a closer look at the issue on linux side
> so that it does not need to depend on PHY being reset by the bootloader.

Yes, as you suspected this is exactly what happened: providing a fix in U-Boot
caused everything to work again in Linux. It would appear as though Linux is
expecting the PHY to be reset/setup/configured by the bootloader in the case
of this board/SoC/PHY.

> [2] https://lore.kernel.org/u-boot/20240118071949.927089-1-jonas@kwiboo.se/T/
> 
> Regards,
> Jonas
> 
> > 
> > [1] https://lore.kernel.org/linux-rockchip/47d55aca-bee6-810f-379f-9431649fefa6@kwiboo.se/
> > 
> > Regards,
> > Jonas
> > 
> >>
> >> Comparing the rock-pi-e's dts file with the one from the roc-rk3328-cc board,
> >> which also uses the layout in this patch, and which also uses the rtl8211e
> >> external PHY, is what led me in this direction.
> >>
> >>>
> >>> ChenYu
> >>>
> >>>> Fixes: b918e81f2145 ("arm64: dts: rockchip: rk3328: Add Radxa ROCK Pi E")
> >>>> Signed-off-by: Trevor Woerner <twoerner@gmail.com>
> >>>> ---
> >>>>  arch/arm64/boot/dts/rockchip/rk3328-rock-pi-e.dts | 10 +++++-----
> >>>>  1 file changed, 5 insertions(+), 5 deletions(-)
> >>>>
> >>>> diff --git a/arch/arm64/boot/dts/rockchip/rk3328-rock-pi-e.dts b/arch/arm64/boot/dts/rockchip/rk3328-rock-pi-e.dts
> >>>> index 096cfa19036e..0739b8fec86e 100644
> >>>> --- a/arch/arm64/boot/dts/rockchip/rk3328-rock-pi-e.dts
> >>>> +++ b/arch/arm64/boot/dts/rockchip/rk3328-rock-pi-e.dts
> >>>> @@ -150,8 +150,11 @@ &gmac2io {
> >>>>         phy-mode = "rgmii";
> >>>>         phy-supply = <&vcc_io>;
> >>>>         pinctrl-names = "default";
> >>>> -       pinctrl-0 = <&rgmiim1_pins>;
> >>>> +       pinctrl-0 = <&rgmiim1_pins>, <&eth_phy_reset_pin>;
> >>>>         snps,aal;
> >>>> +       snps,reset-gpio = <&gpio1 RK_PC2 GPIO_ACTIVE_LOW>;
> >>>> +       snps,reset-active-low;
> >>>> +       snps,reset-delays-us = <0 10000 50000>;
> >>>>         snps,rxpbl = <0x4>;
> >>>>         snps,txpbl = <0x4>;
> >>>>         tx_delay = <0x26>;
> >>>> @@ -165,13 +168,10 @@ mdio {
> >>>>
> >>>>                 rtl8211: ethernet-phy@1 {
> >>>>                         reg = <1>;
> >>>> -                       pinctrl-0 = <&eth_phy_int_pin>, <&eth_phy_reset_pin>;
> >>>> +                       pinctrl-0 = <&eth_phy_int_pin>;
> >>>>                         pinctrl-names = "default";
> >>>>                         interrupt-parent = <&gpio1>;
> >>>>                         interrupts = <24 IRQ_TYPE_LEVEL_LOW>;
> >>>> -                       reset-assert-us = <10000>;
> >>>> -                       reset-deassert-us = <50000>;
> >>>> -                       reset-gpios = <&gpio1 RK_PC2 GPIO_ACTIVE_LOW>;
> >>>>                 };
> >>>>         };
> >>>>  };
> >>>> --
> >>>> 2.43.0.76.g1a87c842ece3
> >>>>
>