[PATCH V2 1/2] arm64: dts: ti: k3-am69-sk: Enable CAN interfaces for AM69 SK board

[sabiya.d@mistralsolutions.com]

From: Dasnavis Sabiya <sabiya.d@ti.com>

AM69 SK board has several CAN bus interfaces on both MCU and MAIN domains.
This enables the CAN interfaces on MCU and MAIN domain.

Signed-off-by: Dasnavis Sabiya <sabiya.d@ti.com>
---
 arch/arm64/boot/dts/ti/k3-am69-sk.dts | 81 +++++++++++++++++++++++++++
 1 file changed, 81 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am69-sk.dts b/arch/arm64/boot/dts/ti/k3-am69-sk.dts
index 8da591579868..64c737cc3d49 100644
--- a/arch/arm64/boot/dts/ti/k3-am69-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am69-sk.dts
@@ -321,6 +321,31 @@ tfp410_out: endpoint {
 			};
 		};
 	};
+
+	transceiver1: can-phy0 {
+		compatible = "ti,tcan1042";
+		#phy-cells = <0>;
+		max-bitrate = <5000000>;
+	};
+
+	transceiver2: can-phy1 {
+		compatible = "ti,tcan1042";
+		#phy-cells = <0>;
+		max-bitrate = <5000000>;
+	};
+
+	transceiver3: can-phy2 {
+		compatible = "ti,tcan1042";
+		#phy-cells = <0>;
+		max-bitrate = <5000000>;
+	};
+
+	transceiver4: can-phy3 {
+		compatible = "ti,tcan1042";
+		#phy-cells = <0>;
+		max-bitrate = <5000000>;
+	};
+
 };
 
 &main_pmx0 {
@@ -429,6 +454,20 @@ hdmi_hpd_pins_default: hdmi-hpd-default-pins {
 			J784S4_IOPAD(0x000, PIN_INPUT, 7) /* (AN35) EXTINTN.GPIO0_0 */
 		>;
 	};
+
+	main_mcan6_pins_default: main-mcan6-default-pins {
+		pinctrl-single,pins = <
+			J784S4_IOPAD(0x098, PIN_INPUT, 0) /* (AH36) MCAN6_RX */
+			J784S4_IOPAD(0x094, PIN_OUTPUT, 0) /* (AG35) MCAN6_TX */
+		>;
+	};
+
+	main_mcan7_pins_default: main-mcan7-default-pins {
+		pinctrl-single,pins = <
+			J784S4_IOPAD(0x0A0, PIN_INPUT, 0) /* (AD34) MCAN7_RX */
+			J784S4_IOPAD(0x09C, PIN_OUTPUT, 0) /* (AF35) MCAN7_TX */
+		>;
+	};
 };
 
 &wkup_pmx2 {
@@ -525,6 +564,20 @@ hdmi_pdn_pins_default: hdmi-pdn-default-pins {
 			J784S4_WKUP_IOPAD(0x090, PIN_INPUT, 7) /* (H37) WKUP_GPIO0_14 */
 		>;
 	};
+
+	mcu_mcan0_pins_default: mcu-mcan0-default-pins {
+		pinctrl-single,pins = <
+			J784S4_WKUP_IOPAD(0x054, PIN_INPUT, 0) /* (F38) MCU_MCAN0_RX */
+			J784S4_WKUP_IOPAD(0x050, PIN_OUTPUT, 0) /* (K33) MCU_MCAN0_TX */
+		>;
+	};
+
+	mcu_mcan1_pins_default: mcu-mcan1-default-pins {
+		pinctrl-single,pins = <
+			J784S4_WKUP_IOPAD(0x06c, PIN_INPUT, 0) /* (K36) WKUP_GPIO0_5.MCU_MCAN1_RX */
+			J784S4_WKUP_IOPAD(0x068, PIN_OUTPUT, 0)/* (H35) WKUP_GPIO0_4.MCU_MCAN1_TX */
+		>;
+	};
 };
 
 &wkup_pmx3 {
@@ -992,3 +1045,31 @@ dp0_out: endpoint {
 		};
 	};
 };
+
+&mcu_mcan0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_mcan0_pins_default>;
+	phys = <&transceiver1>;
+};
+
+&mcu_mcan1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_mcan1_pins_default>;
+	phys = <&transceiver2>;
+};
+
+&main_mcan6 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_mcan6_pins_default>;
+	phys = <&transceiver3>;
+};
+
+&main_mcan7 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_mcan7_pins_default>;
+	phys = <&transceiver4>;
+};
-- 
2.34.1