[PATCH v6 0/7] arm64: dts: add description for solidrun am642 som and hummingboard evb

[PATCH v6 0/7] arm64: dts: add description for solidrun am642 som and hummingboard evb

[Josua Mayer]

This series adds DT bindings and dts descriptions for SolidRun AM642
based SoM and Hummingboard EVB.

Additionally a commit from downstream vendor kernel are included,
enhancing support for pru based ethernet.
I wasn't sure how to properly annotate it in commit description /
signed-off area ...:

1. add description for "Industrial Ethernet Peripherals" (IEP) to am64
   https://git.ti.com/cgit/ti-linux-kernel/ti-linux-kernel/commit/arch/arm64/boot/dts/ti/k3-am64-main.dtsi?h=ti-linux-6.1.y-cicd&id=5afb73d82a014b59462162d960b350b8c58e5ae6
   IEP is already supported in-tree by a driver, and used in
   k3-am65-main.dtsi.

Unfortunately dtbs_check still reports one problem:

- 'mux-controller' does not match any of the regexes
  The expectation seems to be that a mux-controller at minimum has an
  address, something to put behind an @, e.g. "mux-controller@7".
  However this mux is not on a bus, it is just a gpio-mux,
  not sure how to name it better.

Signed-off-by: Josua Mayer <josua@solid-run.com>
---
Changes in v6:
- renamed pinctrl nodes to *-default-pins
  (reported by Vignesh Raghavendra <vigneshr@ti.com>)
  (dropped Reviewed-by: Andrew Davis <afd@ti.com>)
- removed tabs from pinctrl comments to shorten lines
- updated humidity sensor yaml with interrupts property
- updated spi-nor flash yaml with interrupts property
- Link to v5: https://lore.kernel.org/r/20240211-add-am64-som-v5-0-790ed7121249@solid-run.com

Changes in v5:
- abracon,abx80x.yaml:
  - reworded 'compatible' description
  - removed $ref to interrupts.yaml
  - nested example in fake i2c
  - changed maintainer to rtc list
  (reported by Conor Dooley <conor@kernel.org>)
- patch 4/5 dts:
  - re-added status properties for sdhci nodes
    k3-am64-main.dtsi has been changed in-tree since v1
    such that sdhci nodes are explicitly status disabled now.
  - picked up reviewed-by
  (reported by Andrew Davis <afd@ti.com>)
- Link to v4: https://lore.kernel.org/r/20240202-add-am64-som-v4-0-5f8b12af5e71@solid-run.com

Changes in v4:
- abracon,abx80x.yaml: fixed dtc error in example irq reference
- Link to v3: https://lore.kernel.org/r/20240202-add-am64-som-v3-0-2f44023d50e9@solid-run.com

Changes in v3:
- removed lots more status properties, double-checked against soc dtsi
  (reported by Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>)
  (reported by Andrew Davis <afd@ti.com>)
- removed intentionally-disabled pcie node from dts
- rewrote yaml bindings to use enum instead of anyof+const+description
  (reported by Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>)
- abracon yaml
  - added missing maintainer
  - added diode type property type
  - added example
  (reported by Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>)
  - added reference to /schemas/interrupts.yaml#
- use generic name for pru ethernet controller node
  (reported by Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>)
- removed unnamed dmas from pru ethernet controller node
- moved pcie/usb3 features to dtb overlays
- Link to v2: https://lore.kernel.org/r/20240112-add-am64-som-v2-0-1385246c428c@solid-run.com

Changes in v2:
- reordered patchset to drop separate patch adding iep handle to som
- moved dtbs_check warnings to cover letter
- converted abracon abx80x rtc bindings to yaml
- updated dts:
  - remove unnecessary status properties
  - changed non-generic node names
  - use color property for led descriptions,
    they have no default function on evaluation board
  - drop earlycon bootargs from chosen node
  (reported by Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>)
- converted charger node to comment, part not assembled, has no bindings
- picked up acked-by on board bindings patch
- Link to v1: https://lore.kernel.org/r/20240103-add-am64-som-v1-0-dda1f9227aef@solid-run.com

---
Josua Mayer (6):
      dt-bindings: arm: ti: Add bindings for SolidRun AM642 HummingBoard-T
      dt-bindings: rtc: abx80x: convert to yaml
      dt-bindings: iio: humidity: hdc20x0: add optional interrupts property
      dt-bindings: mtd: spi-nor: add optional interrupts property
      arm64: dts: add description for solidrun am642 som and evaluation board
      arm64: dts: ti: hummingboard-t: add overlays for m.2 pci-e and usb-3

Suman Anna (1):
      arm64: dts: ti: k3-am64-main: Add ICSSG IEP nodes

 Documentation/devicetree/bindings/arm/ti/k3.yaml   |   7 +
 .../bindings/iio/humidity/ti,hdc2010.yaml          |   3 +
 .../devicetree/bindings/mtd/jedec,spi-nor.yaml     |   3 +
 .../devicetree/bindings/rtc/abracon,abx80x.txt     |  31 --
 .../devicetree/bindings/rtc/abracon,abx80x.yaml    |  79 +++
 arch/arm64/boot/dts/ti/Makefile                    |   7 +
 arch/arm64/boot/dts/ti/k3-am64-main.dtsi           |  24 +
 .../boot/dts/ti/k3-am642-hummingboard-t-pcie.dtso  |  45 ++
 .../boot/dts/ti/k3-am642-hummingboard-t-usb3.dtso  |  44 ++
 arch/arm64/boot/dts/ti/k3-am642-hummingboard-t.dts | 292 ++++++++++
 arch/arm64/boot/dts/ti/k3-am642-sr-som.dtsi        | 594 +++++++++++++++++++++
 11 files changed, 1098 insertions(+), 31 deletions(-)
---
base-commit: 83d0ff463b50d2395e05339a34e35d14ba82043f
change-id: 20240101-add-am64-som-51a1ca47edf3

Sincerely,
-- 
Josua Mayer <josua@solid-run.com>

[PATCH v6 1/7] dt-bindings: arm: ti: Add bindings for SolidRun AM642 HummingBoard-T

[Josua Mayer]

Add bindings for SolidRun AM642 HummingBoard-T Board, which is the
evaluation board for SolidRun AM642 SoM.

Signed-off-by: Josua Mayer <josua@solid-run.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 Documentation/devicetree/bindings/arm/ti/k3.yaml | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/ti/k3.yaml b/Documentation/devicetree/bindings/arm/ti/k3.yaml
index c6506bccfe88..0233a8b0b6fc 100644
--- a/Documentation/devicetree/bindings/arm/ti/k3.yaml
+++ b/Documentation/devicetree/bindings/arm/ti/k3.yaml
@@ -87,6 +87,13 @@ properties:
           - const: tq,am642-tqma6442l
           - const: ti,am642
 
+      - description: K3 AM642 SoC SolidRun SoM based boards
+        items:
+          - enum:
+              - solidrun,am642-hummingboard-t
+          - const: solidrun,am642-sr-som
+          - const: ti,am642
+
       - description: K3 AM654 SoC
         items:
           - enum:

-- 
2.35.3

[PATCH v6 2/7] dt-bindings: rtc: abx80x: convert to yaml

[Josua Mayer]

Convert the abracon abx80x rtc text bindings to dt-schema format.

In addition to the text description reference generic interrupts
properties and add an example.

Signed-off-by: Josua Mayer <josua@solid-run.com>
---
 .../devicetree/bindings/rtc/abracon,abx80x.txt     | 31 ---------
 .../devicetree/bindings/rtc/abracon,abx80x.yaml    | 79 ++++++++++++++++++++++
 2 files changed, 79 insertions(+), 31 deletions(-)

diff --git a/Documentation/devicetree/bindings/rtc/abracon,abx80x.txt b/Documentation/devicetree/bindings/rtc/abracon,abx80x.txt
deleted file mode 100644
index 2405e35a1bc0..000000000000
--- a/Documentation/devicetree/bindings/rtc/abracon,abx80x.txt
+++ /dev/null
@@ -1,31 +0,0 @@
-Abracon ABX80X I2C ultra low power RTC/Alarm chip
-
-The Abracon ABX80X family consist of the ab0801, ab0803, ab0804, ab0805, ab1801,
-ab1803, ab1804 and ab1805. The ab0805 is the superset of ab080x and the ab1805
-is the superset of ab180x.
-
-Required properties:
-
- - "compatible": should one of:
-        "abracon,abx80x"
-        "abracon,ab0801"
-        "abracon,ab0803"
-        "abracon,ab0804"
-        "abracon,ab0805"
-        "abracon,ab1801"
-        "abracon,ab1803"
-        "abracon,ab1804"
-        "abracon,ab1805"
-        "microcrystal,rv1805"
-	Using "abracon,abx80x" will enable chip autodetection.
- - "reg": I2C bus address of the device
-
-Optional properties:
-
-The abx804 and abx805 have a trickle charger that is able to charge the
-connected battery or supercap. Both the following properties have to be defined
-and valid to enable charging:
-
- - "abracon,tc-diode": should be "standard" (0.6V) or "schottky" (0.3V)
- - "abracon,tc-resistor": should be <0>, <3>, <6> or <11>. 0 disables the output
-                          resistor, the other values are in kOhm.
diff --git a/Documentation/devicetree/bindings/rtc/abracon,abx80x.yaml b/Documentation/devicetree/bindings/rtc/abracon,abx80x.yaml
new file mode 100644
index 000000000000..58dbbca27deb
--- /dev/null
+++ b/Documentation/devicetree/bindings/rtc/abracon,abx80x.yaml
@@ -0,0 +1,79 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/rtc/abracon,abx80x.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Abracon ABX80X I2C ultra low power RTC/Alarm chip
+
+maintainers:
+  - linux-rtc@vger.kernel.org
+
+allOf:
+  - $ref: rtc.yaml#
+
+properties:
+  compatible:
+    description:
+      The wildcard 'abracon,abx80x' may be used to support a mix
+      of different abracon rtc`s. In this case the driver
+      must perform auto-detection from ID register.
+    enum:
+      - abracon,abx80x
+      - abracon,ab0801
+      - abracon,ab0803
+      - abracon,ab0804
+      - abracon,ab0805
+      - abracon,ab1801
+      - abracon,ab1803
+      - abracon,ab1804
+      - abracon,ab1805
+      - microcrystal,rv1805
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  abracon,tc-diode:
+    description:
+      Trickle-charge diode type.
+      Required to enable charging backup battery.
+
+      Supported are 'standard' diodes with a 0.6V drop
+      and 'schottky' diodes with a 0.3V drop.
+    $ref: /schemas/types.yaml#/definitions/string
+    enum:
+      - standard
+      - schottky
+
+  abracon,tc-resistor:
+    description:
+      Trickle-charge resistor value in kOhm.
+      Required to enable charging backup battery.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [0, 3, 6, 11]
+
+required:
+  - compatible
+  - reg
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        rtc@69 {
+            compatible = "abracon,abx80x";
+            reg = <0x69>;
+            abracon,tc-diode = "schottky";
+            abracon,tc-resistor = <3>;
+            interrupts = <44 IRQ_TYPE_EDGE_FALLING>;
+        };
+    };

-- 
2.35.3

[PATCH v6 3/7] dt-bindings: iio: humidity: hdc20x0: add optional interrupts property

[Josua Mayer]

HDC2010 and HDC2080 humidity sensors both have an interrupt / data-ready
signal which can be used for signaling to the host.

Add binding for "interrupts" property so that boards wiring this signal
may describe the connection.

Signed-off-by: Josua Mayer <josua@solid-run.com>
---
 Documentation/devicetree/bindings/iio/humidity/ti,hdc2010.yaml | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/Documentation/devicetree/bindings/iio/humidity/ti,hdc2010.yaml b/Documentation/devicetree/bindings/iio/humidity/ti,hdc2010.yaml
index 79e75a8675cb..e3eca8917517 100644
--- a/Documentation/devicetree/bindings/iio/humidity/ti,hdc2010.yaml
+++ b/Documentation/devicetree/bindings/iio/humidity/ti,hdc2010.yaml
@@ -27,6 +27,9 @@ properties:
   reg:
     maxItems: 1
 
+  interrupts:
+    maxItems: 1
+
 required:
   - compatible
   - reg

-- 
2.35.3

[PATCH v6 4/7] dt-bindings: mtd: spi-nor: add optional interrupts property

[Josua Mayer]

Some spi flash memories have an interrupt signal which can be used for
signalling on-chip events such as busy status or ecc errors to the host.

Add binding for "interrupts" property so that boards wiring this signal
may describe the connection.

Signed-off-by: Josua Mayer <josua@solid-run.com>
---
 Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml
index 58f0cea160ef..6e3afb42926e 100644
--- a/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml
+++ b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml
@@ -52,6 +52,9 @@ properties:
     minItems: 1
     maxItems: 2
 
+  interrupts:
+    maxItems: 1
+
   m25p,fast-read:
     type: boolean
     description:

-- 
2.35.3

[PATCH v6 5/7] arm64: dts: ti: k3-am64-main: Add ICSSG IEP nodes

[Josua Mayer]

From: Suman Anna <s-anna@ti.com>

The ICSSG IP on AM64x SoCs have two Industrial Ethernet Peripherals (IEPs)
to manage/generate Industrial Ethernet functions such as time stamping.
Each IEP sub-module is sourced from an internal clock mux that can be
derived from either of the IP instance's ICSSG_IEP_GCLK or from another
internal ICSSG CORE_CLK mux. Add both the IEP nodes for both the ICSSG
instances. The IEP clock is currently configured to be derived
indirectly from the ICSSG_ICLK running at 250 MHz.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: Josua Mayer <josua@solid-run.com>
---
 arch/arm64/boot/dts/ti/k3-am64-main.dtsi | 24 ++++++++++++++++++++++++
 1 file changed, 24 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am64-main.dtsi b/arch/arm64/boot/dts/ti/k3-am64-main.dtsi
index e348114f42e0..9d2dad8ae8df 100644
--- a/arch/arm64/boot/dts/ti/k3-am64-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am64-main.dtsi
@@ -1244,6 +1244,18 @@ icssg0_iepclk_mux: iepclk-mux@30 {
 			};
 		};
 
+		icssg0_iep0: iep@2e000 {
+			compatible = "ti,am654-icss-iep";
+			reg = <0x2e000 0x1000>;
+			clocks = <&icssg0_iepclk_mux>;
+		};
+
+		icssg0_iep1: iep@2f000 {
+			compatible = "ti,am654-icss-iep";
+			reg = <0x2f000 0x1000>;
+			clocks = <&icssg0_iepclk_mux>;
+		};
+
 		icssg0_mii_rt: mii-rt@32000 {
 			compatible = "ti,pruss-mii", "syscon";
 			reg = <0x32000 0x100>;
@@ -1385,6 +1397,18 @@ icssg1_iepclk_mux: iepclk-mux@30 {
 			};
 		};
 
+		icssg1_iep0: iep@2e000 {
+			compatible = "ti,am654-icss-iep";
+			reg = <0x2e000 0x1000>;
+			clocks = <&icssg1_iepclk_mux>;
+		};
+
+		icssg1_iep1: iep@2f000 {
+			compatible = "ti,am654-icss-iep";
+			reg = <0x2f000 0x1000>;
+			clocks = <&icssg1_iepclk_mux>;
+		};
+
 		icssg1_mii_rt: mii-rt@32000 {
 			compatible = "ti,pruss-mii", "syscon";
 			reg = <0x32000 0x100>;

-- 
2.35.3

[PATCH v6 6/7] arm64: dts: add description for solidrun am642 som and evaluation board

[Josua Mayer]

Add description for the SolidRun AM642 SoM, and HummingBoard-T
evaluation board.

The SoM features:
- 1x cpsw ethernet with phy
- 2x pru ethernet with phy
- eMMC
- spi flash (assembly option)

Additionally microSD and usb-2.0 otg are included in the SoM
description as they are supported boot sources for the SOC boot-rom.

The Carrier provides:
- 3x RJ45 connector
- 2x M.2 connector
- USB-2.0 Hub
- USB-A Connector
- LEDs
- 2x CAN transceiver
- 1x RS485 transceiver
- sensors

The M.2 connectors support either USB-3.1 or PCI-E depending on status
of a mux. By default the mux is switched off.

Signed-off-by: Josua Mayer <josua@solid-run.com>
---
 arch/arm64/boot/dts/ti/Makefile                    |   1 +
 arch/arm64/boot/dts/ti/k3-am642-hummingboard-t.dts | 292 ++++++++++
 arch/arm64/boot/dts/ti/k3-am642-sr-som.dtsi        | 594 +++++++++++++++++++++
 3 files changed, 887 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
index 52c1dc910308..bd73ce06acba 100644
--- a/arch/arm64/boot/dts/ti/Makefile
+++ b/arch/arm64/boot/dts/ti/Makefile
@@ -38,6 +38,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-am62x-sk-hdmi-audio.dtbo
 
 # Boards with AM64x SoC
 dtb-$(CONFIG_ARCH_K3) += k3-am642-evm.dtb
+dtb-$(CONFIG_ARCH_K3) += k3-am642-hummingboard-t.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-am642-phyboard-electra-rdk.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-am642-sk.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-am642-tqma64xxl-mbax4xxl.dtb
diff --git a/arch/arm64/boot/dts/ti/k3-am642-hummingboard-t.dts b/arch/arm64/boot/dts/ti/k3-am642-hummingboard-t.dts
new file mode 100644
index 000000000000..234d76e4e944
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am642-hummingboard-t.dts
@@ -0,0 +1,292 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2023 Josua Mayer <josua@solid-run.com>
+ *
+ * DTS for SolidRun AM642 HummingBoard-T,
+ * running on Cortex A53.
+ *
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/phy/phy.h>
+
+#include "k3-am642.dtsi"
+#include "k3-am642-sr-som.dtsi"
+
+/ {
+	model = "SolidRun AM642 HummingBoard-T";
+	compatible = "solidrun,am642-hummingboard-t", "solidrun,am642-sr-som", "ti,am642";
+
+	aliases {
+		serial5 = &main_uart3;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&leds_default_pins>;
+
+		/* D24 */
+		led1: led-1 {
+			label = "led1";
+			gpios = <&main_gpio0 29 GPIO_ACTIVE_HIGH>;
+			color = <LED_COLOR_ID_GREEN>;
+		};
+
+		/* D25 */
+		led2: led-2 {
+			label = "led2";
+			gpios = <&main_gpio0 30 GPIO_ACTIVE_HIGH>;
+			color = <LED_COLOR_ID_GREEN>;
+		};
+
+		/* D26 */
+		led3: led-3 {
+			label = "led3";
+			gpios = <&main_gpio0 33 GPIO_ACTIVE_HIGH>;
+			color = <LED_COLOR_ID_GREEN>;
+		};
+	};
+
+	regulator-m2-3v3 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&regulator_pcie_3v3_default_pins>;
+		regulator-name = "m2-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&main_gpio1 17 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	regulator-vpp-1v8 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&regulator_vpp_1v8_default_pins>;
+		regulator-name = "vpp-1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&main_gpio1 78 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	serdes_mux: mux-controller {
+		compatible = "gpio-mux";
+		pinctrl-names = "default";
+		pinctrl-0 = <&serdes_mux_default_pins>;
+		#mux-control-cells = <0>;
+		/*
+		 * Mux has 2 IOs:
+		 * - select: 0 = USB-3 (M2); 1 = PCIE (M1)
+		 * - shutdown: 0 = active; 1 = disabled (high impedance)
+		 */
+		mux-gpios = <&main_gpio1 40 GPIO_ACTIVE_HIGH>, <&main_gpio1 41 GPIO_ACTIVE_HIGH>;
+		/* default disabled */
+		idle-state = <2>;
+	};
+};
+
+&main_gpio0 {
+	m2-reset-hog {
+		gpio-hog;
+		gpios = <12 GPIO_ACTIVE_LOW>;
+		output-low; /* deasserted */
+		line-name = "m2-reset";
+	};
+
+	m1-m2-w-disable1-hog {
+		gpio-hog;
+		gpios = <32 GPIO_ACTIVE_LOW>;
+		output-low; /* deasserted */
+		line-name = "m1-m2-pcie-w-disable1";
+	};
+
+	m1-m2-w-disable2-hog {
+		gpio-hog;
+		gpios = <34 GPIO_ACTIVE_LOW>;
+		output-low; /* deasserted */
+		line-name = "m1-m2-pcie-w-disable2";
+	};
+};
+
+&main_gpio1 {
+	m1-pcie-clkreq0-hog {
+		gpio-hog;
+		gpios = <11 GPIO_ACTIVE_LOW>;
+		input;
+		line-name = "m1-pcie-clkreq0";
+	};
+
+	m2-pcie-clkreq-hog {
+		gpio-hog;
+		gpios = <35 GPIO_ACTIVE_LOW>;
+		input;
+		line-name = "m2-pcie-clkreq";
+	};
+};
+
+&main_i2c0 {
+	pinctrl-0 = <&main_i2c0_default_pins>, <&main_i2c0_int_default_pins>;
+
+	humidity-sensor@41 {
+		compatible = "ti,hdc2010";
+		reg = <0x41>;
+		interrupt-parent = <&main_gpio0>;
+		interrupts = <37 IRQ_TYPE_EDGE_FALLING>;
+	};
+
+	light-sensor@44 {
+		compatible = "ti,opt3001";
+		reg = <0x44>;
+		interrupt-parent = <&main_gpio0>;
+		interrupts = <37 IRQ_TYPE_EDGE_FALLING>;
+	};
+
+	/* charger@6a */
+};
+
+&main_i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_i2c1_default_pins>;
+	status = "okay";
+
+	rtc@69 {
+		compatible = "abracon,abx80x";
+		reg = <0x69>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&rtc_int_default_pins>;
+		abracon,tc-diode = "schottky";
+		abracon,tc-resistor = <3>;
+		interrupt-parent = <&main_gpio0>;
+		interrupts = <44 IRQ_TYPE_EDGE_FALLING>;
+	};
+};
+
+&main_mcan0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_mcan0_default_pins>;
+	status = "okay";
+
+	can-transceiver {
+		max-bitrate = <8000000>;
+	};
+};
+
+&main_mcan1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_mcan1_default_pins>;
+	status = "okay";
+
+	can-transceiver {
+		max-bitrate = <8000000>;
+	};
+};
+
+&main_pmx0 {
+	leds_default_pins: leds-default-pins {
+		pinctrl-single,pins = <
+			AM64X_IOPAD(0x0074, PIN_OUTPUT, 7) /* GPMC0_AD14.GPIO0_29 */
+			AM64X_IOPAD(0x0078, PIN_OUTPUT, 7) /* GPMC0_AD15.GPIO0_30 */
+			AM64X_IOPAD(0x0088, PIN_OUTPUT, 7) /* GPMC0_OEn_REn.GPIO0_33 */
+		>;
+	};
+
+	main_i2c0_int_default_pins: main-i2c0-int-default-pins {
+		pinctrl-single,pins = <
+			/* external pull-up on Carrier */
+			AM64X_IOPAD(0x0098, PIN_INPUT, 7) /* GPMC0_WAIT0.GPIO0_37 */
+		>;
+	};
+
+	main_i2c1_default_pins: main-i2c1-default-pins {
+		pinctrl-single,pins = <
+			/* external pull-up on SoM */
+			AM64X_IOPAD(0x0268, PIN_INPUT, 0) /* I2C1_SCL.I2C1_SCL */
+			AM64X_IOPAD(0x026c, PIN_INPUT, 0) /* I2C1_SDA.I2C1_SDA */
+		>;
+	};
+
+	main_mcan0_default_pins: main-mcan0-default-pins {
+		pinctrl-single,pins = <
+			AM64X_IOPAD(0x0254, PIN_INPUT, 0) /* MCAN0_RX.MCAN0_RX */
+			AM64X_IOPAD(0x0250, PIN_OUTPUT, 0) /* MCAN0_TX.MCAN0_TX */
+		>;
+	};
+
+	main_mcan1_default_pins: main-mcan1-default-pins {
+		pinctrl-single,pins = <
+			AM64X_IOPAD(0x025c, PIN_INPUT, 0) /* MCAN1_RX.MCAN1_RX */
+			AM64X_IOPAD(0x0258, PIN_OUTPUT, 0) /* MCAN1_TX.MCAN1_TX */
+		>;
+	};
+
+	main_uart3_default_pins: main-uart3-default-pins {
+		pinctrl-single,pins = <
+			AM64X_IOPAD(0x016c, PIN_INPUT, 10) /* PRG0_PRU0_GPO3.UART3_CTSn */
+			AM64X_IOPAD(0x0170, PIN_OUTPUT, 10) /* PRG0_PRU0_GPO4.UART3_TXD */
+			AM64X_IOPAD(0x0174, PIN_OUTPUT, 10) /* PRG0_PRU0_GPO5.UART3_RTSn */
+			AM64X_IOPAD(0x01ac, PIN_INPUT, 10) /* PRG0_PRU0_GPO19.UART3_RXD */
+		>;
+	};
+
+	pcie0_default_pins: pcie0-default-pins {
+		pinctrl-single,pins = <
+			/* connector M2 RESET */
+			AM64X_IOPAD(0x0030, PIN_OUTPUT, 7) /* OSPI0_CSn1.GPIO0_12 */
+			/* connectors M1 & M2 W_DISABLE1 */
+			AM64X_IOPAD(0x0084, PIN_OUTPUT, 7) /* GPMC0_ADVN_ALE.GPIO0_32 */
+			/* connectors M1 & M2 W_DISABLE2 */
+			AM64X_IOPAD(0x008c, PIN_OUTPUT, 7) /* GPMC0_WEN.GPIO0_34 */
+			/* connectors M1 & M2 PERST0 (PCI Reset) */
+			AM64X_IOPAD(0x019c, PIN_OUTPUT, 7) /* PRG0_PRU0_GPO15.GPIO1_15 */
+			/* connector M1 CLKREQ0 */
+			AM64X_IOPAD(0x018c, PIN_INPUT, 7) /* PRG0_PRU0_GPO11.GPIO1_11 */
+			/* connector M2 CLKREQ0 */
+			AM64X_IOPAD(0x01ec, PIN_INPUT, 7) /* PRG0_PRU1_GPO15.GPIO1_35 */
+		>;
+	};
+
+	regulator_pcie_3v3_default_pins: regulator-pcie-3v3-default-pins {
+		pinctrl-single,pins = <
+			AM64X_IOPAD(0x01a4, PIN_OUTPUT, 7) /* PRG0_PRU0_GPO17.GPIO1_17 */
+		>;
+	};
+
+	regulator_vpp_1v8_default_pins: regulator-vpp-1v8-default-pins {
+		pinctrl-single,pins = <
+			AM64X_IOPAD(0x029c, PIN_OUTPUT, 7) /* MMC1_SDWP.GPIO1_78 */
+		>;
+	};
+
+	rtc_int_default_pins: rtc-int-default-pins {
+		pinctrl-single,pins = <
+			/* external pull-up on Carrier */
+			AM64X_IOPAD(0x00b4, PIN_INPUT, 7) /* GPMC0_CSn3.GPIO0_44 */
+		>;
+	};
+
+	serdes_mux_default_pins: serdes-mux-default-pins {
+		pinctrl-single,pins = <
+			/* SEL, 10k pull-down on carrier, 2.2k pullup on SoM */
+			AM64X_IOPAD(0x0200, PIN_OUTPUT, 7) /* PRG0_MDIO0_MDIO.GPIO1_40 */
+			/* EN */
+			AM64X_IOPAD(0x0204, PIN_OUTPUT, 7) /* PRG0_MDIO0_MDC.GPIO1_41 */
+		>;
+	};
+};
+
+&main_uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_uart3_default_pins>;
+	uart-has-rtscts;
+	rs485-rts-active-low;
+	linux,rs485-enabled-at-boot-time;
+	status = "okay";
+};
+
+&usb0 {
+	dr_mode = "host";
+};
diff --git a/arch/arm64/boot/dts/ti/k3-am642-sr-som.dtsi b/arch/arm64/boot/dts/ti/k3-am642-sr-som.dtsi
new file mode 100644
index 000000000000..c19d0b8bbf0f
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am642-sr-som.dtsi
@@ -0,0 +1,594 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2023 Josua Mayer <josua@solid-run.com>
+ *
+ */
+
+#include <dt-bindings/net/ti-dp83869.h>
+
+/ {
+	model = "SolidRun AM642 SoM";
+	compatible = "solidrun,am642-sr-som", "ti,am642";
+
+	aliases {
+		ethernet0 = &cpsw_port1;
+		ethernet1 = &icssg1_emac0;
+		ethernet2 = &icssg1_emac1;
+		mmc0 = &sdhci0;
+		mmc1 = &sdhci1;
+		serial2 = &main_uart0;
+	};
+
+	chosen {
+		/* SoC default UART console */
+		stdout-path = "serial2:115200n8";
+	};
+
+	/* PRU Ethernet Controller */
+	ethernet {
+		compatible = "ti,am642-icssg-prueth";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pru_rgmii1_default_pins>, <&pru_rgmii2_default_pins>;
+
+		sram = <&oc_sram>;
+		ti,prus = <&pru1_0>, <&rtu1_0>, <&tx_pru1_0>, <&pru1_1>, <&rtu1_1>, <&tx_pru1_1>;
+		firmware-name = "ti-pruss/am65x-sr2-pru0-prueth-fw.elf",
+				"ti-pruss/am65x-sr2-rtu0-prueth-fw.elf",
+				"ti-pruss/am65x-sr2-txpru0-prueth-fw.elf",
+				"ti-pruss/am65x-sr2-pru1-prueth-fw.elf",
+				"ti-pruss/am65x-sr2-rtu1-prueth-fw.elf",
+				"ti-pruss/am65x-sr2-txpru1-prueth-fw.elf";
+
+		/* configure internal pinmux for mii mode */
+		ti,pruss-gp-mux-sel = <2>, <2>, <2>, <2>, <2>, <2>;
+
+		ti,mii-g-rt = <&icssg1_mii_g_rt>;
+		ti,mii-rt = <&icssg1_mii_rt>;
+		ti,iep = <&icssg1_iep0>, <&icssg1_iep1>;
+
+		/*
+		 * Configure icssg interrupt controller to map pru-internal
+		 * interrupts 8/9 via channels 0/1 to host interrupts 0/1.
+		 *
+		 * For details see interrupt controller documentation:
+		 * Documentation/devicetree/bindings/interrupt-controller/ti,pruss-intc.yaml
+		 */
+		interrupt-parent = <&icssg1_intc>;
+		interrupts = <24 0 2>, <25 1 3>;
+		interrupt-names = "tx_ts0", "tx_ts1";
+
+		dmas = <&main_pktdma 0xc200 15>, /* egress slice 0 */
+		       <&main_pktdma 0xc201 15>, /* egress slice 0 */
+		       <&main_pktdma 0xc202 15>, /* egress slice 0 */
+		       <&main_pktdma 0xc203 15>, /* egress slice 0 */
+		       <&main_pktdma 0xc204 15>, /* egress slice 1 */
+		       <&main_pktdma 0xc205 15>, /* egress slice 1 */
+		       <&main_pktdma 0xc206 15>, /* egress slice 1 */
+		       <&main_pktdma 0xc207 15>, /* egress slice 1 */
+		       <&main_pktdma 0x4200 15>, /* ingress slice 0 */
+		       <&main_pktdma 0x4201 15>; /* ingress slice 1 */
+		dma-names = "tx0-0", "tx0-1", "tx0-2", "tx0-3",
+			    "tx1-0", "tx1-1", "tx1-2", "tx1-3",
+			    "rx0", "rx1";
+
+		ethernet-ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			icssg1_emac0: port@0 {
+				reg = <0>;
+				ti,syscon-rgmii-delay = <&main_conf 0x4110>;
+				/* Filled in by bootloader */
+				local-mac-address = [00 00 00 00 00 00];
+				phy-handle = <&ethernet_phy2>;
+				phy-mode = "rgmii-id";
+			};
+
+			icssg1_emac1: port@1 {
+				reg = <1>;
+				ti,syscon-rgmii-delay = <&main_conf 0x4114>;
+				/* Filled in by bootloader */
+				local-mac-address = [00 00 00 00 00 00];
+				phy-handle = <&ethernet_phy1>;
+				phy-mode = "rgmii-id";
+			};
+		};
+	};
+
+	/* DDR16SS0:
+	 * - Bank 1 @ 0x080000000-0x0FFFFFFFF: max. 2GB in 32-bit address space
+	 * - Bank 2 @ 0x880000000-0x9FFFFFFFF: max. 6GB in 64-bit address space
+	 */
+	memory@80000000 {
+		reg = <0x00000000 0x80000000 0x00000000 0x80000000>,
+		      <0x00000008 0x80000000 0x00000001 0x80000000>;
+		device_type = "memory";
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		secure_ddr: optee@9e800000 {
+			reg = <0x00 0x9e800000 0x00 0x01800000>; /* for OP-TEE */
+			no-map;
+		};
+
+		main_r5fss0_core0_dma_memory_region: r5f-dma-memory@a0000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa0000000 0x00 0x100000>;
+			no-map;
+		};
+
+		main_r5fss0_core0_memory_region: r5f-memory@a0100000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa0100000 0x00 0xf00000>;
+			no-map;
+		};
+
+		main_r5fss0_core1_dma_memory_region: r5f-dma-memory@a1000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa1000000 0x00 0x100000>;
+			no-map;
+		};
+
+		main_r5fss0_core1_memory_region: r5f-memory@a1100000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa1100000 0x00 0xf00000>;
+			no-map;
+		};
+
+		main_r5fss1_core0_dma_memory_region: r5f-dma-memory@a2000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa2000000 0x00 0x100000>;
+			no-map;
+		};
+
+		main_r5fss1_core0_memory_region: r5f-memory@a2100000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa2100000 0x00 0xf00000>;
+			no-map;
+		};
+
+		main_r5fss1_core1_dma_memory_region: r5f-dma-memory@a3000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa3000000 0x00 0x100000>;
+			no-map;
+		};
+
+		main_r5fss1_core1_memory_region: r5f-memory@a3100000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa3100000 0x00 0xf00000>;
+			no-map;
+		};
+	};
+
+	vdd_mmc0: regulator-vdd-mmc0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd-mmc0";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+};
+
+&cpsw3g {
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii1_default_pins>;
+};
+
+&cpsw3g_mdio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mdio0_default_pins>;
+	status = "okay";
+
+	ethernet_phy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-id2000.a0f1";
+		reg = <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ethernet_phy0_default_pins>;
+		ti,clk-output-sel = <DP83869_CLK_O_SEL_REF_CLK>;
+		ti,op-mode = <DP83869_RGMII_COPPER_ETHERNET>;
+		/*
+		 * Disable interrupts because ISR never clears 0x0040
+		 *
+		 * interrupt-parent = <&main_gpio1>;
+		 * interrupts = <70 IRQ_TYPE_LEVEL_LOW>;
+		 */
+		/*
+		 * Disable HW Reset because clock signal is daisy-chained
+		 *
+		 * reset-gpios = <&main_gpio0 84 GPIO_ACTIVE_LOW>;
+		 * reset-assert-us = <1>;
+		 * reset-deassert-us = <30>;
+		 */
+	};
+};
+
+&cpsw_port1 {
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethernet_phy0>;
+};
+
+&cpsw_port2 {
+	status = "disabled";
+};
+
+&icssg1_mdio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pru1_mdio0_default_pins>;
+	status = "okay";
+
+	ethernet_phy1: ethernet-phy@3 {
+		compatible = "ethernet-phy-id2000.a0f1";
+		reg = <3>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ethernet_phy1_default_pins>;
+		ti,clk-output-sel = <DP83869_CLK_O_SEL_REF_CLK>;
+		ti,op-mode = <DP83869_RGMII_COPPER_ETHERNET>;
+		/*
+		 * Disable interrupts because ISR never clears 0x0040
+		 *
+		 * interrupt-parent = <&main_gpio1>;
+		 * interrupts = <70 IRQ_TYPE_LEVEL_LOW>;
+		 */
+		/*
+		 * Disable HW Reset because clock signal is daisy-chained
+		 *
+		 * reset-gpios = <&main_gpio0 20 GPIO_ACTIVE_LOW>;
+		 * reset-assert-us = <1>;
+		 * reset-deassert-us = <30>;
+		 */
+	};
+
+	ethernet_phy2: ethernet-phy@f {
+		compatible = "ethernet-phy-id2000.a0f1";
+		reg = <0xf>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ethernet_phy2_default_pins>;
+		ti,op-mode = <DP83869_RGMII_COPPER_ETHERNET>;
+		/*
+		 * Disable interrupts because ISR never clears 0x0040
+		 *
+		 * interrupt-parent = <&main_gpio1>;
+		 * interrupts = <70 IRQ_TYPE_LEVEL_LOW>;
+		 */
+		/*
+		 * Disable HW Reset because clock signal is daisy-chained
+		 *
+		 * reset-gpios = <&main_gpio0 52 GPIO_ACTIVE_LOW>;
+		 * reset-assert-us = <1>;
+		 * reset-deassert-us = <30>;
+		 */
+	};
+};
+
+&mailbox0_cluster2 {
+	status = "okay";
+
+	mbox_main_r5fss0_core0: mbox-main-r5fss0-core0 {
+		ti,mbox-rx = <0 0 2>;
+		ti,mbox-tx = <1 0 2>;
+	};
+
+	mbox_main_r5fss0_core1: mbox-main-r5fss0-core1 {
+		ti,mbox-rx = <2 0 2>;
+		ti,mbox-tx = <3 0 2>;
+	};
+};
+
+&mailbox0_cluster4 {
+	status = "okay";
+
+	mbox_main_r5fss1_core0: mbox-main-r5fss1-core0 {
+		ti,mbox-rx = <0 0 2>;
+		ti,mbox-tx = <1 0 2>;
+	};
+
+	mbox_main_r5fss1_core1: mbox-main-r5fss1-core1 {
+		ti,mbox-rx = <2 0 2>;
+		ti,mbox-tx = <3 0 2>;
+	};
+};
+
+&main_i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_i2c0_default_pins>;
+	status = "okay";
+
+	som_eeprom: eeprom@50 {
+		compatible = "atmel,24c01";
+		reg = <0x50>;
+		pagesize = <8>;
+	};
+};
+
+&main_pmx0 {
+	/* hog global functions */
+	pinctrl-names = "default";
+	pinctrl-0 = <&ethernet_phy_default_pins>;
+
+	ethernet_phy_default_pins: ethernet-phy-default-pins {
+		pinctrl-single,pins = <
+			/* interrupt / power-down, external pull-up on SoM */
+			AM64X_IOPAD(0x0278, PIN_INPUT, 7) /* EXTINTn.GPIO1_70 */
+		>;
+	};
+
+	ethernet_phy0_default_pins: ethernet-phy0-default-pins {
+		pinctrl-single,pins = <
+			/* reset */
+			AM64X_IOPAD(0x0154, PIN_OUTPUT, 7) /* PRG1_PRU1_GPO19.GPIO0_84 */
+			/* reference clock */
+			AM64X_IOPAD(0x0274, PIN_OUTPUT, 5) /* EXT_REFCLK1.CLKOUT0 */
+		>;
+	};
+
+	ethernet_phy1_default_pins: ethernet-phy1-default-pins {
+		pinctrl-single,pins = <
+			/* reset */
+			AM64X_IOPAD(0x0150, PIN_OUTPUT, 7) /* PRG1_PRU1_GPO18.GPIO0_20 */
+			/* led0, external pull-down on SoM */
+			AM64X_IOPAD(0x0128, PIN_INPUT, 7) /* PRG1_PRU1_GPO8.GPIO0_73 */
+			/* led1/rxer */
+			AM64X_IOPAD(0x011c, PIN_INPUT, 7) /* PRG1_PRU1_GPO5.GPIO0_70 */
+		>;
+	};
+
+	ethernet_phy2_default_pins: ethernet-phy2-default-pins {
+		pinctrl-single,pins = <
+			/* reset */
+			AM64X_IOPAD(0x00d4, PIN_OUTPUT, 7) /* PRG1_PRU0_GPO7.GPIO0_52 */
+			/* led0, external pull-down on SoM */
+			AM64X_IOPAD(0x00d8, PIN_INPUT, 7) /* PRG1_PRU0_GPO8.GPIO0_53 */
+			/* led1/rxer */
+			AM64X_IOPAD(0x00cc, PIN_INPUT, 7) /* PRG1_PRU0_GPO5.GPIO0_50 */
+		>;
+	};
+
+	main_i2c0_default_pins: main-i2c0-default-pins {
+		pinctrl-single,pins = <
+			/* external pull-up on SoM */
+			AM64X_IOPAD(0x0260, PIN_INPUT, 0) /* I2C0_SCL.I2C0_SCL */
+			AM64X_IOPAD(0x0264, PIN_INPUT, 0) /* I2C0_SDA.I2C0_SDA */
+		>;
+	};
+
+	/*
+	 * main_mmc0_default_pins: main-mmc0-default-pins
+	 *
+	 * MMC0_CMD: no padconfig
+	 * MMC0_CLK: no padconfig, external pull-up on SoM
+	 * MMC0_DAT0: no padconfig
+	 * MMC0_DAT1: no padconfig
+	 * MMC0_DAT2: no padconfig
+	 * MMC0_DAT3: no padconfig
+	 * MMC0_DAT4: no padconfig
+	 * MMC0_DAT5: no padconfig
+	 * MMC0_DAT6: no padconfig
+	 * MMC0_DAT7: no padconfig
+	 * MMC0_DS: no padconfig, external pull-down on SoM
+	 */
+
+	main_mmc1_default_pins: main-mmc1-default-pins {
+		pinctrl-single,pins = <
+			AM64X_IOPAD(0x0294, PIN_INPUT_PULLUP, 0) /* (J19) MMC1_CMD */
+			AM64X_IOPAD(0x028c, PIN_INPUT, 0) /* MMC1_CLK.MMC1_CLK */
+			AM64X_IOPAD(0x0288, PIN_INPUT_PULLUP, 0) /* MMC1_DAT0.MMC1_DAT0 */
+			AM64X_IOPAD(0x0284, PIN_INPUT_PULLUP, 0) /* MMC1_DAT1.MMC1_DAT1 */
+			AM64X_IOPAD(0x0280, PIN_INPUT_PULLUP, 0) /* MMC1_DAT2.MMC1_DAT2 */
+			AM64X_IOPAD(0x027c, PIN_INPUT_PULLUP, 0) /* MMC1_DAT3.MMC1_DAT3 */
+			/* external pull-down on SoM & Carrier */
+			AM64X_IOPAD(0x0298, PIN_INPUT_PULLUP, 0) /* MMC1_SDCD.MMC1_SDCD */
+			AM64X_IOPAD(0x0290, PIN_INPUT, 0) /* MMC1_CLKLB: clock loopback */
+		>;
+	};
+
+	main_uart0_default_pins: main-uart0-default-pins {
+		pinctrl-single,pins = <
+			AM64X_IOPAD(0x0230, PIN_INPUT, 0) /* UART0_RXD.UART0_RXD */
+			AM64X_IOPAD(0x0234, PIN_OUTPUT, 0) /* UART0_TXD.UART0_TXD */
+		>;
+	};
+
+	mdio0_default_pins: mdio0-default-pins {
+		pinctrl-single,pins = <
+			AM64X_IOPAD(0x01fc, PIN_OUTPUT, 4) /* PRG0_PRU1_GPO19.MDIO0_MDC */
+			AM64X_IOPAD(0x01f8, PIN_INPUT, 4) /* PRG0_PRU1_GPO18.MDIO0_MDIO */
+		>;
+	};
+
+	ospi0_default_pins: ospi0-default-pins {
+		pinctrl-single,pins = <
+			/* external pull-down on SoM */
+			AM64X_IOPAD(0x0000, PIN_OUTPUT, 0) /* OSPI0_CLK.OSPI0_CLK */
+			AM64X_IOPAD(0x0008, PIN_OUTPUT, 0) /* OSPI0_DQS.OSPI0_DQS */
+			/* external pull-up on SoM */
+			AM64X_IOPAD(0x002c, PIN_OUTPUT, 0) /* OSPI0_CSn0.OSPI0_CSn0 */
+			AM64X_IOPAD(0x000c, PIN_INPUT, 0) /* OSPI0_D0.OSPI0_D0 */
+			AM64X_IOPAD(0x0010, PIN_INPUT, 0) /* OSPI0_D1.OSPI0_D1 */
+			AM64X_IOPAD(0x0014, PIN_INPUT, 0) /* OSPI0_D2.OSPI0_D2 */
+			AM64X_IOPAD(0x0018, PIN_INPUT, 0) /* OSPI0_D3.OSPI0_D3 */
+			AM64X_IOPAD(0x001c, PIN_INPUT, 0) /* OSPI0_D4.OSPI0_D4 */
+			AM64X_IOPAD(0x0020, PIN_INPUT, 0) /* OSPI0_D5.OSPI0_D5 */
+			AM64X_IOPAD(0x0024, PIN_INPUT, 0) /* OSPI0_D6.OSPI0_D6 */
+			AM64X_IOPAD(0x0028, PIN_INPUT, 0) /* OSPI0_D7.OSPI0_D7 */
+		>;
+	};
+
+	ospi0_flash0_default_pins: ospi0-flash0-default-pins {
+		pinctrl-single,pins = <
+			AM64X_IOPAD(0x0034, PIN_OUTPUT, 7) /* OSPI0_CSn2.GPIO0_13 */
+			AM64X_IOPAD(0x0038, PIN_INPUT, 7) /* OSPI0_CSn3.GPIO0_14 */
+		>;
+	};
+
+	pru1_mdio0_default_pins: pru1-mdio0-default-pins {
+		pinctrl-single,pins = <
+			AM64X_IOPAD(0x015c, PIN_OUTPUT, 0) /* PRG1_MDIO0_MDC.PRG1_MDIO0_MDC */
+			AM64X_IOPAD(0x0158, PIN_INPUT, 0) /* PRG1_MDIO0_MDIO.PRG1_MDIO0_MDIO */
+		>;
+	};
+
+	pru_rgmii1_default_pins: pru-rgmii1-default-pins {
+		pinctrl-single,pins = <
+			AM64X_IOPAD(0x00b8, PIN_INPUT, 2) /* (Y7) PRG1_PRU0_GPO0.PRG1_RGMII1_RD0 */
+			AM64X_IOPAD(0x00bc, PIN_INPUT, 2) /* (U8) PRG1_PRU0_GPO1.PRG1_RGMII1_RD1 */
+			AM64X_IOPAD(0x00c0, PIN_INPUT, 2) /* (W8) PRG1_PRU0_GPO2.PRG1_RGMII1_RD2 */
+			AM64X_IOPAD(0x00c4, PIN_INPUT, 2) /* (V8) PRG1_PRU0_GPO3.PRG1_RGMII1_RD3 */
+			AM64X_IOPAD(0x00d0, PIN_INPUT, 2) /* (AA7) PRG1_PRU0_GPO6.PRG1_RGMII1_RXC */
+			AM64X_IOPAD(0x00c8, PIN_INPUT, 2) /* (Y8) PRG1_PRU0_GPO4.PRG1_RGMII1_RX_CTL */
+			AM64X_IOPAD(0x00e4, PIN_OUTPUT, 2) /* (AA8) PRG1_PRU0_GPO11.PRG1_RGMII1_TD0 */
+			AM64X_IOPAD(0x00e8, PIN_OUTPUT, 2) /* (U9) PRG1_PRU0_GPO12.PRG1_RGMII1_TD1 */
+			AM64X_IOPAD(0x00ec, PIN_OUTPUT, 2) /* (W9) PRG1_PRU0_GPO13.PRG1_RGMII1_TD2 */
+			AM64X_IOPAD(0x00f0, PIN_OUTPUT, 2) /* (AA9) PRG1_PRU0_GPO14.PRG1_RGMII1_TD3 */
+			AM64X_IOPAD(0x00f8, PIN_INPUT, 2) /* (V9) PRG1_PRU0_GPO16.PRG1_RGMII1_TXC */
+			AM64X_IOPAD(0x00f4, PIN_OUTPUT, 2) /* (Y9) PRG1_PRU0_GPO15.PRG1_RGMII1_TX_CTL */
+		>;
+	};
+
+	pru_rgmii2_default_pins: pru-rgmii2-default-pins {
+		pinctrl-single,pins = <
+			AM64X_IOPAD(0x0108, PIN_INPUT, 2) /* PRG1_PRU1_GPO0.RGMII2_RD0 */
+			AM64X_IOPAD(0x010c, PIN_INPUT, 2) /* PRG1_PRU1_GPO1.RGMII2_RD1 */
+			AM64X_IOPAD(0x0110, PIN_INPUT, 2) /* PRG1_PRU1_GPO2.RGMII2_RD2 */
+			AM64X_IOPAD(0x0114, PIN_INPUT, 2) /* PRG1_PRU1_GPO3.RGMII2_RD3 */
+			AM64X_IOPAD(0x0120, PIN_INPUT, 2) /* PRG1_PRU1_GPO6.RGMII2_RXC */
+			AM64X_IOPAD(0x0118, PIN_INPUT, 2) /* PRG1_PRU1_GPO4.RGMII2_RX_CTL */
+			AM64X_IOPAD(0x0134, PIN_OUTPUT, 2) /* PRG1_PRU1_GPO11.RGMII2_TD0 */
+			AM64X_IOPAD(0x0138, PIN_OUTPUT, 2) /* PRG1_PRU1_GPO12.RGMII2_TD1 */
+			AM64X_IOPAD(0x013c, PIN_OUTPUT, 2) /* PRG1_PRU1_GPO13.RGMII2_TD2 */
+			AM64X_IOPAD(0x0140, PIN_OUTPUT, 2) /* PRG1_PRU1_GPO14.RGMII2_TD3 */
+			AM64X_IOPAD(0x0148, PIN_INPUT, 2) /* PRG1_PRU1_GPO16.RGMII2_TXC */
+			AM64X_IOPAD(0x0144, PIN_OUTPUT, 2) /* PRG1_PRU1_GPO15.RGMII2_TX_CTL */
+		>;
+	};
+
+	rgmii1_default_pins: rgmii1-default-pins {
+		pinctrl-single,pins = <
+			AM64X_IOPAD(0x01cc, PIN_INPUT, 4) /* PRG0_PRU1_GPO7.RGMII1_RD0 */
+			AM64X_IOPAD(0x01d4, PIN_INPUT, 4) /* PRG0_PRU1_GPO9.RGMII1_RD1 */
+			AM64X_IOPAD(0x01d8, PIN_INPUT, 4) /* PRG0_PRU1_GPO10.RGMII1_RD2 */
+			AM64X_IOPAD(0x01f4, PIN_INPUT, 4) /* PRG0_PRU1_GPO17.RGMII1_RD3 */
+			AM64X_IOPAD(0x0188, PIN_INPUT, 4) /* PRG0_PRU0_GPO10.RGMII1_RXC */
+			AM64X_IOPAD(0x0184, PIN_INPUT, 4) /* PRG0_PRU0_GPO9.RGMII1_RX_CTL */
+			AM64X_IOPAD(0x0124, PIN_OUTPUT, 4) /* PRG1_PRU1_GPO7.RGMII1_TD0 */
+			AM64X_IOPAD(0x012c, PIN_OUTPUT, 4) /* PRG1_PRU1_GPO9.RGMII1_TD1 */
+			AM64X_IOPAD(0x0130, PIN_OUTPUT, 4) /* PRG1_PRU1_GPO10.RGMII1_TD2 */
+			AM64X_IOPAD(0x014c, PIN_OUTPUT, 4) /* PRG1_PRU1_GPO17.RGMII1_TD3 */
+			AM64X_IOPAD(0x00e0, PIN_INPUT, 4) /* PRG1_PRU0_GPO10.RGMII1_TXC */
+			AM64X_IOPAD(0x00dc, PIN_OUTPUT, 4) /* PRG1_PRU0_GPO9.RGMII1_TX_CTL */
+		>;
+	};
+
+	usb0_default_pins: usb0-default-pins {
+		pinctrl-single,pins = <
+			AM64X_IOPAD(0x02a8, PIN_OUTPUT, 0) /* USB0_DRVVBUS.USB0_DRVVBUS */
+		>;
+	};
+};
+
+&main_r5fss0_core0 {
+	mboxes = <&mailbox0_cluster2 &mbox_main_r5fss0_core0>;
+	memory-region = <&main_r5fss0_core0_dma_memory_region>,
+			<&main_r5fss0_core0_memory_region>;
+};
+
+&main_r5fss0_core1 {
+	mboxes = <&mailbox0_cluster2 &mbox_main_r5fss0_core1>;
+	memory-region = <&main_r5fss0_core1_dma_memory_region>,
+			<&main_r5fss0_core1_memory_region>;
+};
+
+&main_r5fss1_core0 {
+	mboxes = <&mailbox0_cluster4 &mbox_main_r5fss1_core0>;
+	memory-region = <&main_r5fss1_core0_dma_memory_region>,
+			<&main_r5fss1_core0_memory_region>;
+};
+
+&main_r5fss1_core1 {
+	mboxes = <&mailbox0_cluster4 &mbox_main_r5fss1_core1>;
+	memory-region = <&main_r5fss1_core1_dma_memory_region>,
+			<&main_r5fss1_core1_memory_region>;
+};
+
+/* SoC default UART console */
+&main_uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_uart0_default_pins>;
+	status = "okay";
+};
+
+&ospi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&ospi0_default_pins>;
+	num-cs = <1>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ospi0_flash0_default_pins>;
+		spi-tx-bus-width = <8>;
+		spi-rx-bus-width = <8>;
+		spi-max-frequency = <200000000>;
+		cdns,tshsl-ns = <50>;
+		cdns,tsd2d-ns = <50>;
+		cdns,tchsh-ns = <4>;
+		cdns,tslch-ns = <4>;
+		cdns,read-delay = <0>;
+		interrupt-parent = <&main_gpio0>;
+		interrupts = <14 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&main_gpio0 13 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&sdhci0 {
+	/* mmc0 pins have no padconfig */
+	bus-width = <8>;
+	ti,driver-strength-ohm = <50>;
+	disable-wp;
+	non-removable;
+	cap-mmc-hw-reset;
+	no-sd;
+	/*
+	 * MMC controller supports switching between 1.8V and 3.3V signalling.
+	 * However MMC0 (unlike MMC1) does not integrate an LDO.
+	 * Explicitly link a regulator node for indicating to the driver which
+	 * voltages are actually usable.
+	 */
+	vqmmc-supply = <&vdd_mmc0>;
+	status = "okay";
+};
+
+/*
+ * microSD is on carrier - however since SoC can boot from it,
+ * configure it just in case.
+ */
+&sdhci1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_mmc1_default_pins>;
+	bus-width = <4>;
+	ti,driver-strength-ohm = <50>;
+	disable-wp;
+	status = "okay";
+};
+
+/*
+ * USB settings are a carrier choice - however since SoC can boot from it,
+ * configure as USB-2.0 OTG here, keeping USB-3 serdes disabled.
+ */
+&usb0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb0_default_pins>;
+	dr_mode = "otg";
+	maximum-speed = "high-speed";
+};
+
+&usbss0 {
+	ti,vbus-divider;
+	ti,usb2-only;
+};

-- 
2.35.3

[PATCH v6 7/7] arm64: dts: ti: hummingboard-t: add overlays for m.2 pci-e and usb-3

[Josua Mayer]

HummingBoard-T features two M.2 connectors labeled "M1" and "M2".
The single SerDes lane of the SoC can be routed to either M1 pci-e
signals, or M2 usb-3 signals by a gpio-controlled mux.

Add overlays for each configuration.

Signed-off-by: Josua Mayer <josua@solid-run.com>
---
 arch/arm64/boot/dts/ti/Makefile                    |  6 +++
 .../boot/dts/ti/k3-am642-hummingboard-t-pcie.dtso  | 45 ++++++++++++++++++++++
 .../boot/dts/ti/k3-am642-hummingboard-t-usb3.dtso  | 44 +++++++++++++++++++++
 3 files changed, 95 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
index bd73ce06acba..cd12720638c7 100644
--- a/arch/arm64/boot/dts/ti/Makefile
+++ b/arch/arm64/boot/dts/ti/Makefile
@@ -37,8 +37,14 @@ dtb-$(CONFIG_ARCH_K3) += k3-am62x-sk-csi2-imx219.dtbo
 dtb-$(CONFIG_ARCH_K3) += k3-am62x-sk-hdmi-audio.dtbo
 
 # Boards with AM64x SoC
+k3-am642-hummingboard-t-pcie-dtbs := \
+	k3-am642-hummingboard-t.dtb k3-am642-hummingboard-t-pcie.dtbo
+k3-am642-hummingboard-t-usb3-dtbs := \
+	k3-am642-hummingboard-t.dtb k3-am642-hummingboard-t-usb3.dtbo
 dtb-$(CONFIG_ARCH_K3) += k3-am642-evm.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-am642-hummingboard-t.dtb
+dtb-$(CONFIG_ARCH_K3) += k3-am642-hummingboard-t-pcie.dtb
+dtb-$(CONFIG_ARCH_K3) += k3-am642-hummingboard-t-usb3.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-am642-phyboard-electra-rdk.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-am642-sk.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-am642-tqma64xxl-mbax4xxl.dtb
diff --git a/arch/arm64/boot/dts/ti/k3-am642-hummingboard-t-pcie.dtso b/arch/arm64/boot/dts/ti/k3-am642-hummingboard-t-pcie.dtso
new file mode 100644
index 000000000000..bd9a5caf20da
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am642-hummingboard-t-pcie.dtso
@@ -0,0 +1,45 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2023 Josua Mayer <josua@solid-run.com>
+ *
+ * Overlay for SolidRun AM642 HummingBoard-T to enable PCI-E.
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/phy/phy.h>
+
+#include "k3-serdes.h"
+
+&pcie0_rc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie0_default_pins>;
+	reset-gpios = <&main_gpio1 15 GPIO_ACTIVE_HIGH>;
+	phys = <&serdes0_link>;
+	phy-names = "pcie-phy";
+	num-lanes = <1>;
+	status = "okay";
+};
+
+&serdes0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	serdes0_link: phy@0 {
+		reg = <0>;
+		cdns,num-lanes = <1>;
+		cdns,phy-type = <PHY_TYPE_PCIE>;
+		#phy-cells = <0>;
+		resets = <&serdes_wiz0 1>;
+	};
+};
+
+&serdes_ln_ctrl {
+	idle-states = <AM64_SERDES0_LANE0_PCIE0>;
+};
+
+&serdes_mux {
+	idle-state = <1>;
+};
diff --git a/arch/arm64/boot/dts/ti/k3-am642-hummingboard-t-usb3.dtso b/arch/arm64/boot/dts/ti/k3-am642-hummingboard-t-usb3.dtso
new file mode 100644
index 000000000000..ffcc3bd3c7bc
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am642-hummingboard-t-usb3.dtso
@@ -0,0 +1,44 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2023 Josua Mayer <josua@solid-run.com>
+ *
+ * Overlay for SolidRun AM642 HummingBoard-T to enable USB-3.1.
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/phy/phy.h>
+
+#include "k3-serdes.h"
+
+&serdes0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	serdes0_link: phy@0 {
+		reg = <0>;
+		cdns,num-lanes = <1>;
+		cdns,phy-type = <PHY_TYPE_USB3>;
+		#phy-cells = <0>;
+		resets = <&serdes_wiz0 1>;
+	};
+};
+
+&serdes_ln_ctrl {
+	idle-states = <AM64_SERDES0_LANE0_USB>;
+};
+
+&serdes_mux {
+	idle-state = <0>;
+};
+
+&usbss0 {
+	/delete-property/ ti,usb2-only;
+};
+
+&usb0 {
+	maximum-speed = "super-speed";
+	phys = <&serdes0_link>;
+	phy-names = "cdns3,usb3-phy";
+};

-- 
2.35.3

Re: [PATCH v6 2/7] dt-bindings: rtc: abx80x: convert to yaml

[Alexandre Belloni]

On 12/02/2024 18:38:09+0100, Josua Mayer wrote:
> Convert the abracon abx80x rtc text bindings to dt-schema format.
> 
> In addition to the text description reference generic interrupts
> properties and add an example.
> 
> Signed-off-by: Josua Mayer <josua@solid-run.com>

Did something change since v6? If not, why didn't you collect the
reviewed-by tag?

> ---
>  .../devicetree/bindings/rtc/abracon,abx80x.txt     | 31 ---------
>  .../devicetree/bindings/rtc/abracon,abx80x.yaml    | 79 ++++++++++++++++++++++
>  2 files changed, 79 insertions(+), 31 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/rtc/abracon,abx80x.txt b/Documentation/devicetree/bindings/rtc/abracon,abx80x.txt
> deleted file mode 100644
> index 2405e35a1bc0..000000000000
> --- a/Documentation/devicetree/bindings/rtc/abracon,abx80x.txt
> +++ /dev/null
> @@ -1,31 +0,0 @@
> -Abracon ABX80X I2C ultra low power RTC/Alarm chip
> -
> -The Abracon ABX80X family consist of the ab0801, ab0803, ab0804, ab0805, ab1801,
> -ab1803, ab1804 and ab1805. The ab0805 is the superset of ab080x and the ab1805
> -is the superset of ab180x.
> -
> -Required properties:
> -
> - - "compatible": should one of:
> -        "abracon,abx80x"
> -        "abracon,ab0801"
> -        "abracon,ab0803"
> -        "abracon,ab0804"
> -        "abracon,ab0805"
> -        "abracon,ab1801"
> -        "abracon,ab1803"
> -        "abracon,ab1804"
> -        "abracon,ab1805"
> -        "microcrystal,rv1805"
> -	Using "abracon,abx80x" will enable chip autodetection.
> - - "reg": I2C bus address of the device
> -
> -Optional properties:
> -
> -The abx804 and abx805 have a trickle charger that is able to charge the
> -connected battery or supercap. Both the following properties have to be defined
> -and valid to enable charging:
> -
> - - "abracon,tc-diode": should be "standard" (0.6V) or "schottky" (0.3V)
> - - "abracon,tc-resistor": should be <0>, <3>, <6> or <11>. 0 disables the output
> -                          resistor, the other values are in kOhm.
> diff --git a/Documentation/devicetree/bindings/rtc/abracon,abx80x.yaml b/Documentation/devicetree/bindings/rtc/abracon,abx80x.yaml
> new file mode 100644
> index 000000000000..58dbbca27deb
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/rtc/abracon,abx80x.yaml
> @@ -0,0 +1,79 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/rtc/abracon,abx80x.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Abracon ABX80X I2C ultra low power RTC/Alarm chip
> +
> +maintainers:
> +  - linux-rtc@vger.kernel.org
> +
> +allOf:
> +  - $ref: rtc.yaml#
> +
> +properties:
> +  compatible:
> +    description:
> +      The wildcard 'abracon,abx80x' may be used to support a mix
> +      of different abracon rtc`s. In this case the driver
> +      must perform auto-detection from ID register.
> +    enum:
> +      - abracon,abx80x
> +      - abracon,ab0801
> +      - abracon,ab0803
> +      - abracon,ab0804
> +      - abracon,ab0805
> +      - abracon,ab1801
> +      - abracon,ab1803
> +      - abracon,ab1804
> +      - abracon,ab1805
> +      - microcrystal,rv1805
> +
> +  reg:
> +    maxItems: 1
> +
> +  interrupts:
> +    maxItems: 1
> +
> +  abracon,tc-diode:
> +    description:
> +      Trickle-charge diode type.
> +      Required to enable charging backup battery.
> +
> +      Supported are 'standard' diodes with a 0.6V drop
> +      and 'schottky' diodes with a 0.3V drop.
> +    $ref: /schemas/types.yaml#/definitions/string
> +    enum:
> +      - standard
> +      - schottky
> +
> +  abracon,tc-resistor:
> +    description:
> +      Trickle-charge resistor value in kOhm.
> +      Required to enable charging backup battery.
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    enum: [0, 3, 6, 11]
> +
> +required:
> +  - compatible
> +  - reg
> +
> +unevaluatedProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/interrupt-controller/irq.h>
> +
> +    i2c {
> +        #address-cells = <1>;
> +        #size-cells = <0>;
> +
> +        rtc@69 {
> +            compatible = "abracon,abx80x";
> +            reg = <0x69>;
> +            abracon,tc-diode = "schottky";
> +            abracon,tc-resistor = <3>;
> +            interrupts = <44 IRQ_TYPE_EDGE_FALLING>;
> +        };
> +    };
> 
> -- 
> 2.35.3
> 

-- 
Alexandre Belloni, co-owner and COO, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

Re: [PATCH v6 2/7] dt-bindings: rtc: abx80x: convert to yaml

[Josua Mayer]

Am 12.02.24 um 21:06 schrieb Alexandre Belloni:
> On 12/02/2024 18:38:09+0100, Josua Mayer wrote:
>> Convert the abracon abx80x rtc text bindings to dt-schema format.
>>
>> In addition to the text description reference generic interrupts
>> properties and add an example.
>>
>> Signed-off-by: Josua Mayer <josua@solid-run.com>
> Did something change since v6? If not, why didn't you collect the
> reviewed-by tag?
I forgot about seeing the tag by Krzysztof ... which is why I didn't 
collect it.
Nothing changed since v6, so this still valid:

Reviewed-by: Krzysztof Kozlowski<krzysztof.kozlowski@linaro.org>

>
>> ---
>>   .../devicetree/bindings/rtc/abracon,abx80x.txt     | 31 ---------
>>   .../devicetree/bindings/rtc/abracon,abx80x.yaml    | 79 ++++++++++++++++++++++
>>   2 files changed, 79 insertions(+), 31 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/rtc/abracon,abx80x.txt b/Documentation/devicetree/bindings/rtc/abracon,abx80x.txt
>> deleted file mode 100644
>> index 2405e35a1bc0..000000000000
>> --- a/Documentation/devicetree/bindings/rtc/abracon,abx80x.txt
>> +++ /dev/null
>> @@ -1,31 +0,0 @@
>> -Abracon ABX80X I2C ultra low power RTC/Alarm chip
>> -
>> -The Abracon ABX80X family consist of the ab0801, ab0803, ab0804, ab0805, ab1801,
>> -ab1803, ab1804 and ab1805. The ab0805 is the superset of ab080x and the ab1805
>> -is the superset of ab180x.
>> -
>> -Required properties:
>> -
>> - - "compatible": should one of:
>> -        "abracon,abx80x"
>> -        "abracon,ab0801"
>> -        "abracon,ab0803"
>> -        "abracon,ab0804"
>> -        "abracon,ab0805"
>> -        "abracon,ab1801"
>> -        "abracon,ab1803"
>> -        "abracon,ab1804"
>> -        "abracon,ab1805"
>> -        "microcrystal,rv1805"
>> -	Using "abracon,abx80x" will enable chip autodetection.
>> - - "reg": I2C bus address of the device
>> -
>> -Optional properties:
>> -
>> -The abx804 and abx805 have a trickle charger that is able to charge the
>> -connected battery or supercap. Both the following properties have to be defined
>> -and valid to enable charging:
>> -
>> - - "abracon,tc-diode": should be "standard" (0.6V) or "schottky" (0.3V)
>> - - "abracon,tc-resistor": should be <0>, <3>, <6> or <11>. 0 disables the output
>> -                          resistor, the other values are in kOhm.
>> diff --git a/Documentation/devicetree/bindings/rtc/abracon,abx80x.yaml b/Documentation/devicetree/bindings/rtc/abracon,abx80x.yaml
>> new file mode 100644
>> index 000000000000..58dbbca27deb
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/rtc/abracon,abx80x.yaml
>> @@ -0,0 +1,79 @@
>> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/rtc/abracon,abx80x.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: Abracon ABX80X I2C ultra low power RTC/Alarm chip
>> +
>> +maintainers:
>> +  - linux-rtc@vger.kernel.org
>> +
>> +allOf:
>> +  - $ref: rtc.yaml#
>> +
>> +properties:
>> +  compatible:
>> +    description:
>> +      The wildcard 'abracon,abx80x' may be used to support a mix
>> +      of different abracon rtc`s. In this case the driver
>> +      must perform auto-detection from ID register.
>> +    enum:
>> +      - abracon,abx80x
>> +      - abracon,ab0801
>> +      - abracon,ab0803
>> +      - abracon,ab0804
>> +      - abracon,ab0805
>> +      - abracon,ab1801
>> +      - abracon,ab1803
>> +      - abracon,ab1804
>> +      - abracon,ab1805
>> +      - microcrystal,rv1805
>> +
>> +  reg:
>> +    maxItems: 1
>> +
>> +  interrupts:
>> +    maxItems: 1
>> +
>> +  abracon,tc-diode:
>> +    description:
>> +      Trickle-charge diode type.
>> +      Required to enable charging backup battery.
>> +
>> +      Supported are 'standard' diodes with a 0.6V drop
>> +      and 'schottky' diodes with a 0.3V drop.
>> +    $ref: /schemas/types.yaml#/definitions/string
>> +    enum:
>> +      - standard
>> +      - schottky
>> +
>> +  abracon,tc-resistor:
>> +    description:
>> +      Trickle-charge resistor value in kOhm.
>> +      Required to enable charging backup battery.
>> +    $ref: /schemas/types.yaml#/definitions/uint32
>> +    enum: [0, 3, 6, 11]
>> +
>> +required:
>> +  - compatible
>> +  - reg
>> +
>> +unevaluatedProperties: false
>> +
>> +examples:
>> +  - |
>> +    #include <dt-bindings/interrupt-controller/irq.h>
>> +
>> +    i2c {
>> +        #address-cells = <1>;
>> +        #size-cells = <0>;
>> +
>> +        rtc@69 {
>> +            compatible = "abracon,abx80x";
>> +            reg = <0x69>;
>> +            abracon,tc-diode = "schottky";
>> +            abracon,tc-resistor = <3>;
>> +            interrupts = <44 IRQ_TYPE_EDGE_FALLING>;
>> +        };
>> +    };
>>
>> -- 
>> 2.35.3
>>

Re: [PATCH v6 3/7] dt-bindings: iio: humidity: hdc20x0: add optional interrupts property

[Rob Herring]

On Mon, 12 Feb 2024 18:38:10 +0100, Josua Mayer wrote:
> HDC2010 and HDC2080 humidity sensors both have an interrupt / data-ready
> signal which can be used for signaling to the host.
> 
> Add binding for "interrupts" property so that boards wiring this signal
> may describe the connection.
> 
> Signed-off-by: Josua Mayer <josua@solid-run.com>
> ---
>  Documentation/devicetree/bindings/iio/humidity/ti,hdc2010.yaml | 3 +++
>  1 file changed, 3 insertions(+)
> 

Acked-by: Rob Herring <robh@kernel.org>

Re: [PATCH v6 4/7] dt-bindings: mtd: spi-nor: add optional interrupts property

[Rob Herring]

On Mon, 12 Feb 2024 18:38:11 +0100, Josua Mayer wrote:
> Some spi flash memories have an interrupt signal which can be used for
> signalling on-chip events such as busy status or ecc errors to the host.
> 
> Add binding for "interrupts" property so that boards wiring this signal
> may describe the connection.
> 
> Signed-off-by: Josua Mayer <josua@solid-run.com>
> ---
>  Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml | 3 +++
>  1 file changed, 3 insertions(+)
> 

Acked-by: Rob Herring <robh@kernel.org>