[PATCH v5 1/1] arm64: dts: ti: k3-am62-wakeup: Configure ti-sysc for wkup_uart0

[PATCH v5 1/1] arm64: dts: ti: k3-am62-wakeup: Configure ti-sysc for wkup_uart0

[Tony Lindgren]

The devices in the wkup domain are capable of waking up the system from
suspend. We can configure the wkup domain devices in a generic way using
the ti-sysc interconnect target module driver like we have done with the
earlier TI SoCs.

As ti-sysc manages the SYSCONFIG related registers independent of the
child hardware device, the wake-up configuration is also set even if
wkup_uart0 is reserved by sysfw.

The wkup_uart0 device has interconnect target module register mapping like
dra7 wkup uart. There is a 1 MB interconnect target range with one uart IP
block in the target module. The power domain and clock affects the whole
interconnect target module.

Note we change the functional clock name to follow the ti-sysc binding
and use "fck" instead of "fclk".

Also note that we need to disable the target module reset as noted by
Markus. Otherwise the sysfw using wkup_uart0 can get confused on some
devices leading to boot time issues such as mbox timeouts.

Tested-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Markus Schneider-Pargmann <msp@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
Changes since v4:

- Add ti,no-reset-on-init as noted by Markus

Changes since v3:

- Use the first reg for the target module node name to avoid a
  make W=1 dtbs warning as noted by Nishanth

Changes since v2:

- Fix node name for 8250 IP, it's at offset 0 from the target module

- Added Kevin's Reviewed-by from v2 as the node name change is mostly
  cosmetic

Changes since v1:

- Added Tested-by from Dhruva
---
 arch/arm64/boot/dts/ti/k3-am62-wakeup.dtsi | 34 ++++++++++++++++++----
 1 file changed, 28 insertions(+), 6 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am62-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-am62-wakeup.dtsi
--- a/arch/arm64/boot/dts/ti/k3-am62-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62-wakeup.dtsi
@@ -5,6 +5,8 @@
  * Copyright (C) 2020-2022 Texas Instruments Incorporated - https://www.ti.com/
  */
 
+#include <dt-bindings/bus/ti-sysc.h>
+
 &cbass_wakeup {
 	wkup_conf: syscon@43000000 {
 		bootph-all;
@@ -21,14 +23,34 @@ chipid: chipid@14 {
 		};
 	};
 
-	wkup_uart0: serial@2b300000 {
-		compatible = "ti,am64-uart", "ti,am654-uart";
-		reg = <0x00 0x2b300000 0x00 0x100>;
-		interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>;
+	target-module@2b300050 {
+		compatible = "ti,sysc-omap2", "ti,sysc";
+		reg = <0 0x2b300050 0 0x4>,
+		      <0 0x2b300054 0 0x4>,
+		      <0 0x2b300058 0 0x4>;
+		reg-names = "rev", "sysc", "syss";
+		ti,sysc-mask = <(SYSC_OMAP2_ENAWAKEUP |
+				 SYSC_OMAP2_SOFTRESET |
+				 SYSC_OMAP2_AUTOIDLE)>;
+		ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+				<SYSC_IDLE_NO>,
+				<SYSC_IDLE_SMART>,
+				<SYSC_IDLE_SMART_WKUP>;
+		ti,syss-mask = <1>;
+		ti,no-reset-on-init;
 		power-domains = <&k3_pds 114 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 114 0>;
-		clock-names = "fclk";
-		status = "disabled";
+		clock-names = "fck";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0 0x2b300000 0x100000>;
+
+		wkup_uart0: serial@0 {
+			compatible = "ti,am64-uart", "ti,am654-uart";
+			reg = <0 0x100>;
+			interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
 	};
 
 	wkup_i2c0: i2c@2b200000 {
-- 
2.43.1

Re: [PATCH v5 1/1] arm64: dts: ti: k3-am62-wakeup: Configure ti-sysc for wkup_uart0

[Vignesh Raghavendra]

Hi Tony Lindgren,

On Tue, 13 Feb 2024 13:25:08 +0200, Tony Lindgren wrote:
> The devices in the wkup domain are capable of waking up the system from
> suspend. We can configure the wkup domain devices in a generic way using
> the ti-sysc interconnect target module driver like we have done with the
> earlier TI SoCs.
> 
> As ti-sysc manages the SYSCONFIG related registers independent of the
> child hardware device, the wake-up configuration is also set even if
> wkup_uart0 is reserved by sysfw.
> 
> [...]

I have applied the following to branch ti-k3-dts-next on [1].
Thank you!

[1/1] arm64: dts: ti: k3-am62-wakeup: Configure ti-sysc for wkup_uart0
      commit: 403ffe31494f38196628f26c570430bdaabcf617

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent up the chain during
the next merge window (or sooner if it is a relevant bug fix), however if
problems are discovered then the patch may be dropped or reverted.

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

[1] https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux.git
--
Vignesh