From: Alex Soo <yuklin.soo@starfivetech.com>
To: Linus Walleij <linus.walleij@linaro.org>,
Bartosz Golaszewski <bartosz.golaszewski@linaro.org>,
Hal Feng <hal.feng@starfivetech.com>,
Ley Foon Tan <leyfoon.tan@starfivetech.com>,
Jianlong Huang <jianlong.huang@starfivetech.com>,
Emil Renner Berthing <kernel@esmil.dk>,
Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
Conor Dooley <conor+dt@kernel.org>,
Drew Fustini <drew@beagleboard.org>
Cc: linux-gpio@vger.kernel.org, linux-kernel@vger.kernel.org,
devicetree@vger.kernel.org, linux-riscv@lists.infradead.org,
Paul Walmsley <paul.walmsley@sifive.com>,
Palmer Dabbelt <palmer@dabbelt.com>,
Albert Ou <aou@eecs.berkeley.edu>,
Alex Soo <yuklin.soo@starfivetech.com>
Subject: [RFC PATCH v2 3/6] pinctrl: starfive: jh8100: add pinctrl driver for sys_west domain
Date: Tue, 20 Feb 2024 14:42:43 +0800 [thread overview]
Message-ID: <20240220064246.467216-4-yuklin.soo@starfivetech.com> (raw)
In-Reply-To: <20240220064246.467216-1-yuklin.soo@starfivetech.com>
Add pinctrl driver for sys_west domain.
Signed-off-by: Alex Soo <yuklin.soo@starfivetech.com>
---
drivers/pinctrl/starfive/Kconfig | 12 ++
drivers/pinctrl/starfive/Makefile | 1 +
.../pinctrl-starfive-jh8100-sys-west.c | 168 ++++++++++++++++++
.../starfive/pinctrl-starfive-jh8100.h | 4 +
4 files changed, 185 insertions(+)
create mode 100644 drivers/pinctrl/starfive/pinctrl-starfive-jh8100-sys-west.c
diff --git a/drivers/pinctrl/starfive/Kconfig b/drivers/pinctrl/starfive/Kconfig
index afcbf9d4dc8d..d78f161a636c 100644
--- a/drivers/pinctrl/starfive/Kconfig
+++ b/drivers/pinctrl/starfive/Kconfig
@@ -70,3 +70,15 @@ config PINCTRL_STARFIVE_JH8100_SYS_EAST
This also provides an interface to the GPIO pins not used by other
peripherals supporting inputs, outputs, configuring pull-up/pull-down
and interrupts on input changes.
+
+config PINCTRL_STARFIVE_JH8100_SYS_WEST
+ tristate "StarFive JH8100 SoC System IOMUX-West pinctrl and GPIO driver"
+ depends on ARCH_STARFIVE || COMPILE_TEST
+ depends on OF
+ select PINCTRL_STARFIVE_JH8100
+ default ARCH_STARFIVE
+ help
+ Say yes here to support system iomux-west pin control on the StarFive JH8100 SoC.
+ This also provides an interface to the GPIO pins not used by other
+ peripherals supporting inputs, outputs, configuring pull-up/pull-down
+ and interrupts on input changes.
diff --git a/drivers/pinctrl/starfive/Makefile b/drivers/pinctrl/starfive/Makefile
index 45698c502b48..784465157ae2 100644
--- a/drivers/pinctrl/starfive/Makefile
+++ b/drivers/pinctrl/starfive/Makefile
@@ -8,3 +8,4 @@ obj-$(CONFIG_PINCTRL_STARFIVE_JH7110_AON) += pinctrl-starfive-jh7110-aon.o
obj-$(CONFIG_PINCTRL_STARFIVE_JH8100) += pinctrl-starfive-jh8100.o
obj-$(CONFIG_PINCTRL_STARFIVE_JH8100_SYS_EAST) += pinctrl-starfive-jh8100-sys-east.o
+obj-$(CONFIG_PINCTRL_STARFIVE_JH8100_SYS_WEST) += pinctrl-starfive-jh8100-sys-west.o
diff --git a/drivers/pinctrl/starfive/pinctrl-starfive-jh8100-sys-west.c b/drivers/pinctrl/starfive/pinctrl-starfive-jh8100-sys-west.c
new file mode 100644
index 000000000000..0aebb30596af
--- /dev/null
+++ b/drivers/pinctrl/starfive/pinctrl-starfive-jh8100-sys-west.c
@@ -0,0 +1,168 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Pinctrl / GPIO driver for StarFive JH8100 SoC sys west controller
+ *
+ * Copyright (C) 2023-2024 StarFive Technology Co., Ltd.
+ * Author: Alex Soo <yuklin.soo@starfivetech.com>
+ *
+ */
+
+#include <linux/gpio/driver.h>
+#include <linux/module.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+
+#include <dt-bindings/pinctrl/starfive,jh8100-pinctrl.h>
+
+#include "../core.h"
+#include "../pinmux.h"
+#include "../pinconf.h"
+#include "pinctrl-starfive-jh8100.h"
+
+#define JH8100_SYS_W_NGPIO 16
+#define JH8100_SYS_W_GC_BASE 0
+
+/* registers */
+#define JH8100_SYS_W_DOEN 0x000
+#define JH8100_SYS_W_DOUT 0x010
+#define JH8100_SYS_W_GPI 0x020
+#define JH8100_SYS_W_GPIOIN 0x068
+
+#define JH8100_SYS_W_GPIOEN 0x048
+#define JH8100_SYS_W_GPIOIS0 0x04c
+#define JH8100_SYS_W_GPIOIC0 0x050
+#define JH8100_SYS_W_GPIOIBE0 0x054
+#define JH8100_SYS_W_GPIOIEV0 0x058
+#define JH8100_SYS_W_GPIOIE0 0x05c
+#define JH8100_SYS_W_GPIORIS0 0x060
+#define JH8100_SYS_W_GPIOMIS0 0x064
+
+static const struct pinctrl_pin_desc jh8100_sys_w_pins[] = {
+ PINCTRL_PIN(PAD_GPIO0_W, "SYS_W_GPIO0"),
+ PINCTRL_PIN(PAD_GPIO1_W, "SYS_W_GPIO1"),
+ PINCTRL_PIN(PAD_GPIO2_W, "SYS_W_GPIO2"),
+ PINCTRL_PIN(PAD_GPIO3_W, "SYS_W_GPIO3"),
+ PINCTRL_PIN(PAD_GPIO4_W, "SYS_W_GPIO4"),
+ PINCTRL_PIN(PAD_GPIO5_W, "SYS_W_GPIO5"),
+ PINCTRL_PIN(PAD_GPIO6_W, "SYS_W_GPIO6"),
+ PINCTRL_PIN(PAD_GPIO7_W, "SYS_W_GPIO7"),
+ PINCTRL_PIN(PAD_GPIO8_W, "SYS_W_GPIO8"),
+ PINCTRL_PIN(PAD_GPIO9_W, "SYS_W_GPIO9"),
+ PINCTRL_PIN(PAD_GPIO10_W, "SYS_W_GPIO10"),
+ PINCTRL_PIN(PAD_GPIO11_W, "SYS_W_GPIO11"),
+ PINCTRL_PIN(PAD_GPIO12_W, "SYS_W_GPIO12"),
+ PINCTRL_PIN(PAD_GPIO13_W, "SYS_W_GPIO13"),
+ PINCTRL_PIN(PAD_GPIO14_W, "SYS_W_GPIO14"),
+ PINCTRL_PIN(PAD_GPIO15_W, "SYS_W_GPIO15"),
+};
+
+static const struct jh8100_gpio_func_sel
+ jh8100_sys_w_func_sel[ARRAY_SIZE(jh8100_sys_w_pins)] = {
+ [PAD_GPIO0_W] = { 0xb4, 0, 2 },
+ [PAD_GPIO1_W] = { 0xb4, 12, 2 },
+ [PAD_GPIO2_W] = { 0xb4, 14, 2 },
+ [PAD_GPIO3_W] = { 0xb4, 16, 2 },
+ [PAD_GPIO4_W] = { 0xb4, 18, 2 },
+ [PAD_GPIO5_W] = { 0xb4, 20, 2 },
+ [PAD_GPIO6_W] = { 0xb4, 22, 2 },
+ [PAD_GPIO7_W] = { 0xb4, 24, 2 },
+ [PAD_GPIO8_W] = { 0xb4, 26, 2 },
+ [PAD_GPIO9_W] = { 0xb4, 28, 2 },
+ [PAD_GPIO10_W] = { 0xb4, 2, 2 },
+ [PAD_GPIO11_W] = { 0xb4, 4, 2 },
+ [PAD_GPIO12_W] = { 0xb4, 6, 2 },
+ [PAD_GPIO13_W] = { 0xb4, 8, 2 },
+ [PAD_GPIO14_W] = { 0xb4, 10, 2 },
+};
+
+#ifdef CONFIG_PM_SLEEP
+static int jh8100_sys_w_pinctrl_suspend(struct device *dev)
+{
+ struct jh8100_pinctrl *sfp;
+ int i;
+
+ sfp = dev_get_drvdata(dev);
+ if (!sfp)
+ return -EINVAL;
+
+ for (i = 0; i < sfp->info->nregs; i++)
+ sfp->jh8100_sys_west_regs[i] = readl_relaxed(sfp->base + (i * 4));
+
+ return pinctrl_force_sleep(sfp->pctl);
+}
+
+static int jh8100_sys_w_pinctrl_resume(struct device *dev)
+{
+ struct jh8100_pinctrl *sfp;
+ int i;
+
+ sfp = dev_get_drvdata(dev);
+ if (!sfp)
+ return -EINVAL;
+
+ for (i = 0; i < sfp->info->nregs; i++)
+ writel_relaxed(sfp->jh8100_sys_west_regs[i], sfp->base + (i * 4));
+
+ return pinctrl_force_default(sfp->pctl);
+}
+#endif
+
+static SIMPLE_DEV_PM_OPS(jh8100_sys_w_pinctrl_dev_pm_ops,
+ jh8100_sys_w_pinctrl_suspend,
+ jh8100_sys_w_pinctrl_resume);
+
+static const struct jh8100_gpio_irq_reg jh8100_sys_w_irq_reg = {
+ .is_reg_base = JH8100_SYS_W_GPIOIS0,
+ .ic_reg_base = JH8100_SYS_W_GPIOIC0,
+ .ibe_reg_base = JH8100_SYS_W_GPIOIBE0,
+ .iev_reg_base = JH8100_SYS_W_GPIOIEV0,
+ .ie_reg_base = JH8100_SYS_W_GPIOIE0,
+ .ris_reg_base = JH8100_SYS_W_GPIORIS0,
+ .mis_reg_base = JH8100_SYS_W_GPIOMIS0,
+ .ien_reg_base = JH8100_SYS_W_GPIOEN,
+};
+
+static const struct jh8100_pinctrl_domain_info jh8100_sys_w_pinctrl_info = {
+ .pins = jh8100_sys_w_pins,
+ .npins = ARRAY_SIZE(jh8100_sys_w_pins),
+ .ngpios = JH8100_SYS_W_NGPIO,
+ .gc_base = JH8100_SYS_W_GC_BASE,
+ .name = JH8100_SYS_W_DOMAIN_NAME,
+ .nregs = JH8100_SYS_W_REG_NUM,
+ .dout_reg_base = JH8100_SYS_W_DOUT,
+ .dout_mask = GENMASK(5, 0),
+ .doen_reg_base = JH8100_SYS_W_DOEN,
+ .doen_mask = GENMASK(4, 0),
+ .gpi_reg_base = JH8100_SYS_W_GPI,
+ .gpi_mask = GENMASK(4, 0),
+ .gpioin_reg_base = JH8100_SYS_W_GPIOIN,
+ .func_sel = jh8100_sys_w_func_sel,
+ .irq_reg = &jh8100_sys_w_irq_reg,
+ .mis_pin_num = JH8100_SYS_W_NGPIO,
+};
+
+static const struct of_device_id jh8100_sys_w_pinctrl_of_match[] = {
+ {
+ .compatible = "starfive,jh8100-sys-pinctrl-west",
+ .data = &jh8100_sys_w_pinctrl_info,
+ },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, jh8100_sys_w_pinctrl_of_match);
+
+static struct platform_driver jh8100_sys_w_pinctrl_driver = {
+ .probe = jh8100_pinctrl_probe,
+ .driver = {
+ .name = "starfive-jh8100-sys-pinctrl-west",
+#ifdef CONFIG_PM_SLEEP
+ .pm = &jh8100_sys_w_pinctrl_dev_pm_ops,
+#endif
+ .of_match_table = jh8100_sys_w_pinctrl_of_match,
+ },
+};
+module_platform_driver(jh8100_sys_w_pinctrl_driver);
+
+MODULE_DESCRIPTION("Pinctrl driver for StarFive JH8100 SoC sys west controller");
+MODULE_AUTHOR("Alex Soo <yuklin.soo@starfivetech.com>");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/pinctrl/starfive/pinctrl-starfive-jh8100.h b/drivers/pinctrl/starfive/pinctrl-starfive-jh8100.h
index 920cdd8b6376..92d3b5d6de40 100644
--- a/drivers/pinctrl/starfive/pinctrl-starfive-jh8100.h
+++ b/drivers/pinctrl/starfive/pinctrl-starfive-jh8100.h
@@ -13,10 +13,13 @@
#include <linux/pinctrl/pinconf-generic.h>
#include <linux/pinctrl/pinmux.h>
+#define JH8100_SYS_W_DOMAIN_NAME "jh8100-sys-west"
#define JH8100_SYS_E_DOMAIN_NAME "jh8100-sys-east"
+#define JH8100_SYS_W_REG_NUM 44
#define JH8100_SYS_E_REG_NUM 116
+#define JH8100_SYS_W_GPO_PDA_00_15_CFG 0x074
#define JH8100_SYS_E_GPO_PDA_00_47_CFG 0x114
struct jh8100_pinctrl {
@@ -29,6 +32,7 @@ struct jh8100_pinctrl {
/* register read/write mutex */
struct mutex mutex;
const struct jh8100_pinctrl_domain_info *info;
+ unsigned int jh8100_sys_west_regs[JH8100_SYS_W_REG_NUM];
unsigned int jh8100_sys_east_regs[JH8100_SYS_E_REG_NUM];
/* wakeup */
int wakeup_gpio;
--
2.43.0
next prev parent reply other threads:[~2024-02-20 6:44 UTC|newest]
Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-02-20 6:42 [RFC PATCH v2 0/6] Add Pinctrl driver for Starfive JH8100 SoC Alex Soo
2024-02-20 6:42 ` [RFC PATCH v2 1/6] dt-bindings: pinctrl: starfive: Add JH8100 pinctrl Alex Soo
2024-02-20 8:11 ` Krzysztof Kozlowski
2024-02-20 19:10 ` Conor Dooley
2024-02-21 7:24 ` Krzysztof Kozlowski
2024-02-21 19:39 ` Conor Dooley
2024-02-23 0:24 ` Rob Herring
2024-02-24 8:46 ` Krzysztof Kozlowski
2024-02-24 19:20 ` Conor Dooley
2024-02-28 17:03 ` Rob Herring
2024-02-28 19:34 ` Conor Dooley
2024-02-20 6:42 ` [RFC PATCH v2 2/6] pinctrl: starfive: jh8100: add main and sys_east driver Alex Soo
2024-02-29 13:03 ` Linus Walleij
2024-05-03 11:12 ` Yuklin Soo
2024-02-20 6:42 ` Alex Soo [this message]
2024-02-20 6:42 ` [RFC PATCH v2 4/6] pinctrl: starfive: jh8100: add pinctrl driver for sys_gmac domain Alex Soo
2024-02-20 6:42 ` [RFC PATCH v2 5/6] pinctrl: starfive: jh8100: add pinctrl driver for AON domain Alex Soo
2024-02-20 6:42 ` [RFC PATCH v2 6/6] riscv: dts: starfive: jh8100: add pinctrl device tree nodes Alex Soo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20240220064246.467216-4-yuklin.soo@starfivetech.com \
--to=yuklin.soo@starfivetech.com \
--cc=aou@eecs.berkeley.edu \
--cc=bartosz.golaszewski@linaro.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=drew@beagleboard.org \
--cc=hal.feng@starfivetech.com \
--cc=jianlong.huang@starfivetech.com \
--cc=kernel@esmil.dk \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=leyfoon.tan@starfivetech.com \
--cc=linus.walleij@linaro.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-riscv@lists.infradead.org \
--cc=palmer@dabbelt.com \
--cc=paul.walmsley@sifive.com \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).