Re: [PATCH 1/3] dt-bindings: pwm: add support for MC33XS2410

[Dimitri Fedrau <dima.fedrau@gmail.com>]

Am Wed, Feb 28, 2024 at 02:59:48PM +0100 schrieb Krzysztof Kozlowski:
> On 28/02/2024 14:32, Dimitri Fedrau wrote:
> > Adding documentation for MC33XS2410 pwm driver.
> 
> Driver as Linux driver? If so, please rephrase to describe hardware.
> 
Will fix it.
> > 
> > Signed-off-by: Dimitri Fedrau <dima.fedrau@gmail.com>
> > ---
> >  .../bindings/pwm/nxp,mc33xs2410.yaml          | 105 ++++++++++++++++++
> >  1 file changed, 105 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/pwm/nxp,mc33xs2410.yaml
> > 
> > diff --git a/Documentation/devicetree/bindings/pwm/nxp,mc33xs2410.yaml b/Documentation/devicetree/bindings/pwm/nxp,mc33xs2410.yaml
> > new file mode 100644
> > index 000000000000..bd387dbe69be
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/pwm/nxp,mc33xs2410.yaml
> > @@ -0,0 +1,105 @@
> > +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
> > +%YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/pwm/nxp,mc33xs2410.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: MC33XS2410 PWM driver
> 
> Driver as Linux driver? If so, please rephrase to describe hardware.
>
Will fix it.
> > +
> > +maintainers:
> > +  - Dimitri Fedrau <dima.fedrau@gmail.com>
> > +
> > +allOf:
> > +  - $ref: pwm.yaml#
> > +  - $ref: /schemas/spi/spi-peripheral-props.yaml#
> > +
> > +properties:
> > +  compatible:
> > +    const: nxp,mc33xs2410
> > +
> > +  reg:
> > +    maxItems: 1
> > +
> > +  spi-max-frequency:
> > +    maximum: 10000000
> > +
> > +  spi-cpha: true
> > +
> > +  spi-cs-setup-delay-ns:
> > +    minimum: 100
> > +    default: 100
> > +
> > +  spi-cs-hold-delay-ns:
> > +    minimum: 10
> > +    default: 10
> > +
> > +  spi-cs-inactive-delay-ns:
> > +    minimum: 300
> > +    default: 300
> > +
> > +  reset-gpios:
> > +    description:
> > +      GPIO connected to the active low reset pin.
> > +    maxItems: 1
> > +
> > +  "#pwm-cells":
> > +    const: 3
> > +
> > +  pwms:
> > +    description:
> > +      Direct inputs(di0-3) are used to directly turn-on or turn-off the
> > +      outputs. The external PWM clock can be used if the internal clock
> > +      doesn't meet timing requirements.
> 
> pwm is input for pwm?
> 
Yes.
> > +    maxItems: 5
> > +
> > +  pwm-names:
> > +    items:
> > +      - const: di0
> > +      - const: di1
> > +      - const: di2
> > +      - const: di3
> > +      - const: ext_clk
> 
> Aren't these clocks?
> 
di0-3 are PWM input signals which are translated to output voltage "vpwr".
ext_clk is described as PWM clock in the datasheet. Didn't used it, just
mentioned it here for completeness.
> > +
> > +  vdd-supply:
> > +    description:
> > +      Logic supply voltage
> > +
> > +  vspi-supply:
> > +    description:
> > +      Supply voltage for SPI
> > +
> > +  vpwr-supply:
> > +    description:
> > +      Power switch supply
> > +
> > +  interrupts:
> > +    maxItems: 1
> > +
> > +required:
> > +  - compatible
> > +  - reg
> > +
> > +additionalProperties: false
> 
> Instead:
> unevaluatedProperties: false
> 
Will fix it.
> > +
> > +examples:
> > +  - |
> > +    #include <dt-bindings/gpio/gpio.h>
> > +    spi {
> > +        #address-cells = <1>;
> > +        #size-cells = <0>;
> > +
> > +       pwm@0 {
> > +           compatible = "nxp,mc33xs2410";
> > +           reg = <0x0>;
> > +           spi-max-frequency = <4000000>;
> > +           spi-cpha;
> > +           spi-cs-setup-delay-ns = <100>;
> > +           spi-cs-hold-delay-ns = <10>;
> > +           spi-cs-inactive-delay-ns = <300>;
> > +           reset-gpios = <&gpio3 22 GPIO_ACTIVE_LOW>;
> > +           #pwm-cells = <3>;
> 
> Make example complete, so provide all properties, like interrupts, pwms
> and whatever you have in the binding.
> 
I could make the binding complete, but I haven't used all properties nor
does the driver supports them.
> Best regards,
> Krzysztof
> 
Best regards,
Dimitri