From: Udit Kumar <u-kumar1@ti.com>
To: <nm@ti.com>, <vigneshr@ti.com>,
<linux-arm-kernel@lists.infradead.org>,
<devicetree@vger.kernel.org>
Cc: <kristo@kernel.org>, <robh@kernel.org>, <krzk+dt@kernel.org>,
<conor+dt@kernel.org>, <linux-kernel@vger.kernel.org>,
Udit Kumar <u-kumar1@ti.com>
Subject: [PATCH 1/4] arm64: dts: ti: k3-j784s4-evm: Arranging mux and macro update
Date: Mon, 15 Apr 2024 12:03:26 +0530 [thread overview]
Message-ID: <20240415063329.3286600-2-u-kumar1@ti.com> (raw)
In-Reply-To: <20240415063329.3286600-1-u-kumar1@ti.com>
Updating J784S4 macro for pin mux instead of J721S2.
Also arranging pin mux in order of main_pmx0/1, wkup_pmx0/1/2/3
along with fixing pin type for TX as output of wkup_uart.
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
---
arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 116 +++++++++++------------
1 file changed, 56 insertions(+), 60 deletions(-)
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
index 81fd7afac8c5..1424c6be8e39 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
@@ -338,21 +338,73 @@ J784S4_IOPAD(0x010, PIN_INPUT_PULLUP, 8) /* (AH33) MCAN13_RX.I2C4_SDA */
};
};
+&wkup_pmx0 {
+ bootph-all;
+ mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-default-pins {
+ bootph-all;
+ pinctrl-single,pins = <
+ J784S4_WKUP_IOPAD(0x000, PIN_OUTPUT, 0) /* (E32) MCU_OSPI0_CLK */
+ J784S4_WKUP_IOPAD(0x02c, PIN_OUTPUT, 0) /* (A32) MCU_OSPI0_CSn0 */
+ J784S4_WKUP_IOPAD(0x00c, PIN_INPUT, 0) /* (B33) MCU_OSPI0_D0 */
+ J784S4_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (B32) MCU_OSPI0_D1 */
+ J784S4_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (C33) MCU_OSPI0_D2 */
+ J784S4_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (C35) MCU_OSPI0_D3 */
+ J784S4_WKUP_IOPAD(0x01c, PIN_INPUT, 0) /* (D33) MCU_OSPI0_D4 */
+ J784S4_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (D34) MCU_OSPI0_D5 */
+ J784S4_WKUP_IOPAD(0x024, PIN_INPUT, 0) /* (E34) MCU_OSPI0_D6 */
+ J784S4_WKUP_IOPAD(0x028, PIN_INPUT, 0) /* (E33) MCU_OSPI0_D7 */
+ J784S4_WKUP_IOPAD(0x008, PIN_INPUT, 0) /* (C34) MCU_OSPI0_DQS */
+ >;
+ };
+};
+
+&wkup_pmx1 {
+ bootph-all;
+ mcu_fss0_ospi0_1_pins_default: mcu-fss0-ospi0-1-default-pins {
+ bootph-all;
+ pinctrl-single,pins = <
+ J784S4_WKUP_IOPAD(0x004, PIN_OUTPUT, 6) /* (C32) MCU_OSPI0_ECC_FAIL */
+ J784S4_WKUP_IOPAD(0x000, PIN_OUTPUT, 6) /* (B34) MCU_OSPI0_RESET_OUT0 */
+ >;
+ };
+
+ pmic_irq_pins_default: pmic-irq-default-pins {
+ pinctrl-single,pins = <
+ /* (G33) MCU_OSPI1_CSn1.WKUP_GPIO0_39 */
+ J784S4_WKUP_IOPAD(0x028, PIN_INPUT, 7)
+ >;
+ };
+
+ mcu_fss0_ospi1_pins_default: mcu-fss0-ospi1-default-pins {
+ bootph-all;
+ pinctrl-single,pins = <
+ J784S4_WKUP_IOPAD(0x008, PIN_OUTPUT, 0) /* (F32) MCU_OSPI1_CLK */
+ J784S4_WKUP_IOPAD(0x024, PIN_OUTPUT, 0) /* (G32) MCU_OSPI1_CSn0 */
+ J784S4_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (E35) MCU_OSPI1_D0 */
+ J784S4_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (D31) MCU_OSPI1_D1 */
+ J784S4_WKUP_IOPAD(0x01C, PIN_INPUT, 0) /* (G31) MCU_OSPI1_D2 */
+ J784S4_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (F33) MCU_OSPI1_D3 */
+ J784S4_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (F31) MCU_OSPI1_DQS */
+ J784S4_WKUP_IOPAD(0x00C, PIN_INPUT, 0) /* (C31) MCU_OSPI1_LBCLKO */
+ >;
+ };
+};
+
&wkup_pmx2 {
bootph-all;
wkup_uart0_pins_default: wkup-uart0-default-pins {
bootph-all;
pinctrl-single,pins = <
- J721S2_WKUP_IOPAD(0x048, PIN_INPUT, 0) /* (K35) WKUP_UART0_RXD */
- J721S2_WKUP_IOPAD(0x04c, PIN_INPUT, 0) /* (K34) WKUP_UART0_TXD */
+ J784S4_WKUP_IOPAD(0x048, PIN_INPUT, 0) /* (K35) WKUP_UART0_RXD */
+ J784S4_WKUP_IOPAD(0x04c, PIN_OUTPUT, 0) /* (K34) WKUP_UART0_TXD */
>;
};
wkup_i2c0_pins_default: wkup-i2c0-default-pins {
bootph-all;
pinctrl-single,pins = <
- J721S2_WKUP_IOPAD(0x98, PIN_INPUT, 0) /* (N33) WKUP_I2C0_SCL */
- J721S2_WKUP_IOPAD(0x9c, PIN_INPUT, 0) /* (N35) WKUP_I2C0_SDA */
+ J784S4_WKUP_IOPAD(0x98, PIN_INPUT, 0) /* (N33) WKUP_I2C0_SCL */
+ J784S4_WKUP_IOPAD(0x9c, PIN_INPUT, 0) /* (N35) WKUP_I2C0_SDA */
>;
};
@@ -417,62 +469,6 @@ J784S4_WKUP_IOPAD(0x108, PIN_INPUT, 0) /* (Y36) MCU_ADC1_AIN7 */
};
};
-&wkup_pmx1 {
- status = "okay";
-
- pmic_irq_pins_default: pmic-irq-default-pins {
- pinctrl-single,pins = <
- /* (G33) MCU_OSPI1_CSn1.WKUP_GPIO0_39 */
- J784S4_WKUP_IOPAD(0x028, PIN_INPUT, 7)
- >;
- };
-};
-
-&wkup_pmx0 {
- bootph-all;
- mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-default-pins {
- bootph-all;
- pinctrl-single,pins = <
- J784S4_WKUP_IOPAD(0x000, PIN_OUTPUT, 0) /* (E32) MCU_OSPI0_CLK */
- J784S4_WKUP_IOPAD(0x02c, PIN_OUTPUT, 0) /* (A32) MCU_OSPI0_CSn0 */
- J784S4_WKUP_IOPAD(0x00c, PIN_INPUT, 0) /* (B33) MCU_OSPI0_D0 */
- J784S4_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (B32) MCU_OSPI0_D1 */
- J784S4_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (C33) MCU_OSPI0_D2 */
- J784S4_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (C35) MCU_OSPI0_D3 */
- J784S4_WKUP_IOPAD(0x01c, PIN_INPUT, 0) /* (D33) MCU_OSPI0_D4 */
- J784S4_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (D34) MCU_OSPI0_D5 */
- J784S4_WKUP_IOPAD(0x024, PIN_INPUT, 0) /* (E34) MCU_OSPI0_D6 */
- J784S4_WKUP_IOPAD(0x028, PIN_INPUT, 0) /* (E33) MCU_OSPI0_D7 */
- J784S4_WKUP_IOPAD(0x008, PIN_INPUT, 0) /* (C34) MCU_OSPI0_DQS */
- >;
- };
-};
-
-&wkup_pmx1 {
- bootph-all;
- mcu_fss0_ospi0_1_pins_default: mcu-fss0-ospi0-1-default-pins {
- bootph-all;
- pinctrl-single,pins = <
- J784S4_WKUP_IOPAD(0x004, PIN_OUTPUT, 6) /* (C32) MCU_OSPI0_ECC_FAIL */
- J784S4_WKUP_IOPAD(0x000, PIN_OUTPUT, 6) /* (B34) MCU_OSPI0_RESET_OUT0 */
- >;
- };
-
- mcu_fss0_ospi1_pins_default: mcu-fss0-ospi1-default-pins {
- bootph-all;
- pinctrl-single,pins = <
- J784S4_WKUP_IOPAD(0x008, PIN_OUTPUT, 0) /* (F32) MCU_OSPI1_CLK */
- J784S4_WKUP_IOPAD(0x024, PIN_OUTPUT, 0) /* (G32) MCU_OSPI1_CSn0 */
- J784S4_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (E35) MCU_OSPI1_D0 */
- J784S4_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (D31) MCU_OSPI1_D1 */
- J784S4_WKUP_IOPAD(0x01C, PIN_INPUT, 0) /* (G31) MCU_OSPI1_D2 */
- J784S4_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (F33) MCU_OSPI1_D3 */
- J784S4_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (F31) MCU_OSPI1_DQS */
- J784S4_WKUP_IOPAD(0x00C, PIN_INPUT, 0) /* (C31) MCU_OSPI1_LBCLKO */
- >;
- };
-};
-
&wkup_uart0 {
/* Firmware usage */
status = "reserved";
--
2.34.1
next prev parent reply other threads:[~2024-04-15 6:33 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-04-15 6:33 [PATCH 0/4] Arranging mux and macro update Udit Kumar
2024-04-15 6:33 ` Udit Kumar [this message]
2024-04-15 7:31 ` [PATCH 1/4] arm64: dts: ti: k3-j784s4-evm: " Francesco Dolcini
2024-04-15 7:38 ` Kumar, Udit
2024-04-15 6:33 ` [PATCH 2/4] arm64: dts: ti: k3-am69-sk: Fix UART pin type " Udit Kumar
2024-04-15 6:33 ` [PATCH 3/4] arm64: dts: ti: k3-j7200: Arranging pin mux in order Udit Kumar
2024-04-15 6:33 ` [PATCH 4/4] arm64: dts: ti: k3-j721s2: " Udit Kumar
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20240415063329.3286600-2-u-kumar1@ti.com \
--to=u-kumar1@ti.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=kristo@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=nm@ti.com \
--cc=robh@kernel.org \
--cc=vigneshr@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox