[PATCH v1 1/2] riscv: dts: starfive: visionfive 2: Remove non-existing TDM hardware

[Hannah Peuckmann <hannah.peuckmann@canonical.com>]

This partially reverts
commit e7c304c0346d ("riscv: dts: starfive: jh7110: add the node and pins configuration for tdm")

This added device tree nodes for TDM hardware that is not actually on the
VisionFive 2 board, but connected on the 40pin header. Many different extension
boards could be added on those pins, so this should be handled by overlays
instead.
This also conflicts with the I2S node which also attempts to grab GPIO 44:

  starfive-jh7110-sys-pinctrl 13040000.pinctrl: pin GPIO44 already requested by 10090000.tdm; cannot claim for 120c0000.i2s

Fixes: e7c304c0346d ("riscv: dts: starfive: jh7110: add the node and pins configuration for tdm")
Signed-off-by: Hannah Peuckmann <hannah.peuckmann@canonical.com>
---
 .../jh7110-starfive-visionfive-2.dtsi         | 40 -------------------
 1 file changed, 40 deletions(-)

diff --git a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
index 45b58b6f3df8..d89eef6e2633 100644
--- a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
+++ b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
@@ -622,40 +622,6 @@ GPOEN_ENABLE,
 		};
 	};
 
-	tdm_pins: tdm-0 {
-		tx-pins {
-			pinmux = <GPIOMUX(44, GPOUT_SYS_TDM_TXD,
-					      GPOEN_ENABLE,
-					      GPI_NONE)>;
-			bias-pull-up;
-			drive-strength = <2>;
-			input-disable;
-			input-schmitt-disable;
-			slew-rate = <0>;
-		};
-
-		rx-pins {
-			pinmux = <GPIOMUX(61, GPOUT_HIGH,
-					      GPOEN_DISABLE,
-					      GPI_SYS_TDM_RXD)>;
-			input-enable;
-		};
-
-		sync-pins {
-			pinmux = <GPIOMUX(63, GPOUT_HIGH,
-					      GPOEN_DISABLE,
-					      GPI_SYS_TDM_SYNC)>;
-			input-enable;
-		};
-
-		pcmclk-pins {
-			pinmux = <GPIOMUX(38, GPOUT_HIGH,
-					      GPOEN_DISABLE,
-					      GPI_SYS_TDM_CLK)>;
-			input-enable;
-		};
-	};
-
 	uart0_pins: uart0-0 {
 		tx-pins {
 			pinmux = <GPIOMUX(5, GPOUT_SYS_UART0_TX,
@@ -681,12 +647,6 @@ GPOEN_DISABLE,
 	};
 };
 
-&tdm {
-	pinctrl-names = "default";
-	pinctrl-0 = <&tdm_pins>;
-	status = "okay";
-};
-
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pins>;
-- 
2.40.1