From: Ryan Walklin <ryan@testtoast.com>
To: dri-devel@lists.freedesktop.org, devicetree@vger.kernel.org
Cc: Neil Armstrong <neil.armstrong@linaro.org>,
Jessica Zhang <quic_jesszhan@quicinc.com>,
Sam Ravnborg <sam@ravnborg.org>, David Airlie <airlied@gmail.com>,
Daniel Vetter <daniel@ffwll.ch>,
Maarten Lankhorst <maarten.lankhorst@linux.intel.com>,
Maxime Ripard <mripard@kernel.org>,
Thomas Zimmermann <tzimmermann@suse.de>,
Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>,
Hironori KIKUCHI <kikuchan98@gmail.com>,
Chris Morgan <macroalpha82@gmail.com>,
Andre Przywara <andre.przywara@arm.com>,
John Watts <contact@jookia.org>,
Ryan Walklin <ryan@testtoast.com>
Subject: [PATCH v3 2/2] drm: panel: nv3052c: Add WL-355608-A8 panel
Date: Fri, 31 May 2024 09:12:15 +1200 [thread overview]
Message-ID: <20240530211415.44201-4-ryan@testtoast.com> (raw)
In-Reply-To: <20240530211415.44201-1-ryan@testtoast.com>
The WL-355608-A8 is a 3.5" 640x480@60Hz RGB LCD display from an unknown
OEM used in a number of handheld gaming devices made by Anbernic.
Limited information is available online however the panel timing values
(below) have been obtained from the vendor BSP. The panel appears to
integrate a NV3052C LCD driver (or clone). Available devices address it
in SPI/RGB mode, with the timing signals generated from the device
SoC (Allwinner H700) and passed through.
Add a panel definition and display mode to the existing NV3502C driver.
It was assumed during bringup that the initialisation sequence was the
same as the existing Fascontek FS035VG158 panel, proved working during
experimentation, however subsequent dumping of the init sequence with a
logic analyser confirms one small change to VCOM_ADJ3 from 0x4a to 0x44,
therefore a separate set of registers is also added.
Timings:
| Active | FP | Sync | BP | Total
-----------|--------|------|------|------|-------
Horizontal | 640 | 64 | 20 | 46 | 770
Vertical | 480 | 21 | 4 | 15 | 520
Signed-off-by: Ryan Walklin <ryan@testtoast.com>
Co-developed-by: Hironori KIKUCHI <kikuchan98@gmail.com>
Signed-off-by: Hironori KIKUCHI <kikuchan98@gmail.com>
Reviewed-by: John Watts <contact@jookia.org>
---
Changelog v1..v2:
- Update .compatible string to match dt-binding
- Add co-developer sign-off and review tags
Changelog v2..v3:
- Trailing whitespace as per checkpatch.pl (no functional changes)
---
.../gpu/drm/panel/panel-newvision-nv3052c.c | 225 ++++++++++++++++++
1 file changed, 225 insertions(+)
diff --git a/drivers/gpu/drm/panel/panel-newvision-nv3052c.c b/drivers/gpu/drm/panel/panel-newvision-nv3052c.c
index 1aab0c9ae5..e986d98235 100644
--- a/drivers/gpu/drm/panel/panel-newvision-nv3052c.c
+++ b/drivers/gpu/drm/panel/panel-newvision-nv3052c.c
@@ -433,6 +433,202 @@ static const struct nv3052c_reg fs035vg158_panel_regs[] = {
{ 0x36, 0x0a }, // bgr = 1, ss = 1, gs = 0
};
+
+static const struct nv3052c_reg wl_355608_a8_panel_regs[] = {
+ // EXTC Command set enable, select page 1
+ { 0xff, 0x30 }, { 0xff, 0x52 }, { 0xff, 0x01 },
+ // Mostly unknown registers
+ { 0xe3, 0x00 },
+ { 0x40, 0x00 },
+ { 0x03, 0x40 },
+ { 0x04, 0x00 },
+ { 0x05, 0x03 },
+ { 0x08, 0x00 },
+ { 0x09, 0x07 },
+ { 0x0a, 0x01 },
+ { 0x0b, 0x32 },
+ { 0x0c, 0x32 },
+ { 0x0d, 0x0b },
+ { 0x0e, 0x00 },
+ { 0x23, 0xa0 },
+ { 0x24, 0x0c },
+ { 0x25, 0x06 },
+ { 0x26, 0x14 },
+ { 0x27, 0x14 },
+ { 0x38, 0xcc }, // VCOM_ADJ1
+ { 0x39, 0xd7 }, // VCOM_ADJ2
+ { 0x3a, 0x44 }, // VCOM_ADJ3
+ { 0x28, 0x40 },
+ { 0x29, 0x01 },
+ { 0x2a, 0xdf },
+ { 0x49, 0x3c },
+ { 0x91, 0x77 }, // EXTPW_CTRL2
+ { 0x92, 0x77 }, // EXTPW_CTRL3
+ { 0xa0, 0x55 },
+ { 0xa1, 0x50 },
+ { 0xa4, 0x9c },
+ { 0xa7, 0x02 },
+ { 0xa8, 0x01 },
+ { 0xa9, 0x01 },
+ { 0xaa, 0xfc },
+ { 0xab, 0x28 },
+ { 0xac, 0x06 },
+ { 0xad, 0x06 },
+ { 0xae, 0x06 },
+ { 0xaf, 0x03 },
+ { 0xb0, 0x08 },
+ { 0xb1, 0x26 },
+ { 0xb2, 0x28 },
+ { 0xb3, 0x28 },
+ { 0xb4, 0x33 },
+ { 0xb5, 0x08 },
+ { 0xb6, 0x26 },
+ { 0xb7, 0x08 },
+ { 0xb8, 0x26 },
+ { 0xf0, 0x00 },
+ { 0xf6, 0xc0 },
+ // EXTC Command set enable, select page 2
+ { 0xff, 0x30 }, { 0xff, 0x52 }, { 0xff, 0x02 },
+ // Set gray scale voltage to adjust gamma
+ { 0xb0, 0x0b }, // PGAMVR0
+ { 0xb1, 0x16 }, // PGAMVR1
+ { 0xb2, 0x17 }, // PGAMVR2
+ { 0xb3, 0x2c }, // PGAMVR3
+ { 0xb4, 0x32 }, // PGAMVR4
+ { 0xb5, 0x3b }, // PGAMVR5
+ { 0xb6, 0x29 }, // PGAMPR0
+ { 0xb7, 0x40 }, // PGAMPR1
+ { 0xb8, 0x0d }, // PGAMPK0
+ { 0xb9, 0x05 }, // PGAMPK1
+ { 0xba, 0x12 }, // PGAMPK2
+ { 0xbb, 0x10 }, // PGAMPK3
+ { 0xbc, 0x12 }, // PGAMPK4
+ { 0xbd, 0x15 }, // PGAMPK5
+ { 0xbe, 0x19 }, // PGAMPK6
+ { 0xbf, 0x0e }, // PGAMPK7
+ { 0xc0, 0x16 }, // PGAMPK8
+ { 0xc1, 0x0a }, // PGAMPK9
+ // Set gray scale voltage to adjust gamma
+ { 0xd0, 0x0c }, // NGAMVR0
+ { 0xd1, 0x17 }, // NGAMVR0
+ { 0xd2, 0x14 }, // NGAMVR1
+ { 0xd3, 0x2e }, // NGAMVR2
+ { 0xd4, 0x32 }, // NGAMVR3
+ { 0xd5, 0x3c }, // NGAMVR4
+ { 0xd6, 0x22 }, // NGAMPR0
+ { 0xd7, 0x3d }, // NGAMPR1
+ { 0xd8, 0x0d }, // NGAMPK0
+ { 0xd9, 0x07 }, // NGAMPK1
+ { 0xda, 0x13 }, // NGAMPK2
+ { 0xdb, 0x13 }, // NGAMPK3
+ { 0xdc, 0x11 }, // NGAMPK4
+ { 0xdd, 0x15 }, // NGAMPK5
+ { 0xde, 0x19 }, // NGAMPK6
+ { 0xdf, 0x10 }, // NGAMPK7
+ { 0xe0, 0x17 }, // NGAMPK8
+ { 0xe1, 0x0a }, // NGAMPK9
+ // EXTC Command set enable, select page 3
+ { 0xff, 0x30 }, { 0xff, 0x52 }, { 0xff, 0x03 },
+ // Set various timing settings
+ { 0x00, 0x2a }, // GIP_VST_1
+ { 0x01, 0x2a }, // GIP_VST_2
+ { 0x02, 0x2a }, // GIP_VST_3
+ { 0x03, 0x2a }, // GIP_VST_4
+ { 0x04, 0x61 }, // GIP_VST_5
+ { 0x05, 0x80 }, // GIP_VST_6
+ { 0x06, 0xc7 }, // GIP_VST_7
+ { 0x07, 0x01 }, // GIP_VST_8
+ { 0x08, 0x03 }, // GIP_VST_9
+ { 0x09, 0x04 }, // GIP_VST_10
+ { 0x70, 0x22 }, // GIP_ECLK1
+ { 0x71, 0x80 }, // GIP_ECLK2
+ { 0x30, 0x2a }, // GIP_CLK_1
+ { 0x31, 0x2a }, // GIP_CLK_2
+ { 0x32, 0x2a }, // GIP_CLK_3
+ { 0x33, 0x2a }, // GIP_CLK_4
+ { 0x34, 0x61 }, // GIP_CLK_5
+ { 0x35, 0xc5 }, // GIP_CLK_6
+ { 0x36, 0x80 }, // GIP_CLK_7
+ { 0x37, 0x23 }, // GIP_CLK_8
+ { 0x40, 0x03 }, // GIP_CLKA_1
+ { 0x41, 0x04 }, // GIP_CLKA_2
+ { 0x42, 0x05 }, // GIP_CLKA_3
+ { 0x43, 0x06 }, // GIP_CLKA_4
+ { 0x44, 0x11 }, // GIP_CLKA_5
+ { 0x45, 0xe8 }, // GIP_CLKA_6
+ { 0x46, 0xe9 }, // GIP_CLKA_7
+ { 0x47, 0x11 }, // GIP_CLKA_8
+ { 0x48, 0xea }, // GIP_CLKA_9
+ { 0x49, 0xeb }, // GIP_CLKA_10
+ { 0x50, 0x07 }, // GIP_CLKB_1
+ { 0x51, 0x08 }, // GIP_CLKB_2
+ { 0x52, 0x09 }, // GIP_CLKB_3
+ { 0x53, 0x0a }, // GIP_CLKB_4
+ { 0x54, 0x11 }, // GIP_CLKB_5
+ { 0x55, 0xec }, // GIP_CLKB_6
+ { 0x56, 0xed }, // GIP_CLKB_7
+ { 0x57, 0x11 }, // GIP_CLKB_8
+ { 0x58, 0xef }, // GIP_CLKB_9
+ { 0x59, 0xf0 }, // GIP_CLKB_10
+ // Map internal GOA signals to GOA output pad
+ { 0xb1, 0x01 }, // PANELD2U2
+ { 0xb4, 0x15 }, // PANELD2U5
+ { 0xb5, 0x16 }, // PANELD2U6
+ { 0xb6, 0x09 }, // PANELD2U7
+ { 0xb7, 0x0f }, // PANELD2U8
+ { 0xb8, 0x0d }, // PANELD2U9
+ { 0xb9, 0x0b }, // PANELD2U10
+ { 0xba, 0x00 }, // PANELD2U11
+ { 0xc7, 0x02 }, // PANELD2U24
+ { 0xca, 0x17 }, // PANELD2U27
+ { 0xcb, 0x18 }, // PANELD2U28
+ { 0xcc, 0x0a }, // PANELD2U29
+ { 0xcd, 0x10 }, // PANELD2U30
+ { 0xce, 0x0e }, // PANELD2U31
+ { 0xcf, 0x0c }, // PANELD2U32
+ { 0xd0, 0x00 }, // PANELD2U33
+ // Map internal GOA signals to GOA output pad
+ { 0x81, 0x00 }, // PANELU2D2
+ { 0x84, 0x15 }, // PANELU2D5
+ { 0x85, 0x16 }, // PANELU2D6
+ { 0x86, 0x10 }, // PANELU2D7
+ { 0x87, 0x0a }, // PANELU2D8
+ { 0x88, 0x0c }, // PANELU2D9
+ { 0x89, 0x0e }, // PANELU2D10
+ { 0x8a, 0x02 }, // PANELU2D11
+ { 0x97, 0x00 }, // PANELU2D24
+ { 0x9a, 0x17 }, // PANELU2D27
+ { 0x9b, 0x18 }, // PANELU2D28
+ { 0x9c, 0x0f }, // PANELU2D29
+ { 0x9d, 0x09 }, // PANELU2D30
+ { 0x9e, 0x0b }, // PANELU2D31
+ { 0x9f, 0x0d }, // PANELU2D32
+ { 0xa0, 0x01 }, // PANELU2D33
+ // EXTC Command set enable, select page 2
+ { 0xff, 0x30 }, { 0xff, 0x52 }, { 0xff, 0x02 },
+ // Unknown registers
+ { 0x01, 0x01 },
+ { 0x02, 0xda },
+ { 0x03, 0xba },
+ { 0x04, 0xa8 },
+ { 0x05, 0x9a },
+ { 0x06, 0x70 },
+ { 0x07, 0xff },
+ { 0x08, 0x91 },
+ { 0x09, 0x90 },
+ { 0x0a, 0xff },
+ { 0x0b, 0x8f },
+ { 0x0c, 0x60 },
+ { 0x0d, 0x58 },
+ { 0x0e, 0x48 },
+ { 0x0f, 0x38 },
+ { 0x10, 0x2b },
+ // EXTC Command set enable, select page 0
+ { 0xff, 0x30 }, { 0xff, 0x52 }, { 0xff, 0x00 },
+ // Display Access Control
+ { 0x36, 0x0a }, // bgr = 1, ss = 1, gs = 0
+};
+
static inline struct nv3052c *to_nv3052c(struct drm_panel *panel)
{
return container_of(panel, struct nv3052c, panel);
@@ -670,6 +866,21 @@ static const struct drm_display_mode fs035vg158_modes[] = {
},
};
+static const struct drm_display_mode wl_355608_a8_mode[] = {
+ {
+ .clock = 24000,
+ .hdisplay = 640,
+ .hsync_start = 640 + 64,
+ .hsync_end = 640 + 64 + 20,
+ .htotal = 640 + 64 + 20 + 46,
+ .vdisplay = 480,
+ .vsync_start = 480 + 21,
+ .vsync_end = 480 + 21 + 4,
+ .vtotal = 480 + 21 + 4 + 15,
+ .flags = DRM_MODE_FLAG_NVSYNC | DRM_MODE_FLAG_NHSYNC,
+ },
+};
+
static const struct nv3052c_panel_info ltk035c5444t_panel_info = {
.display_modes = ltk035c5444t_modes,
.num_modes = ARRAY_SIZE(ltk035c5444t_modes),
@@ -692,9 +903,21 @@ static const struct nv3052c_panel_info fs035vg158_panel_info = {
.panel_regs_len = ARRAY_SIZE(fs035vg158_panel_regs),
};
+static const struct nv3052c_panel_info wl_355608_a8_panel_info = {
+ .display_modes = wl_355608_a8_mode,
+ .num_modes = ARRAY_SIZE(wl_355608_a8_mode),
+ .width_mm = 150,
+ .height_mm = 94,
+ .bus_format = MEDIA_BUS_FMT_RGB888_1X24,
+ .bus_flags = DRM_BUS_FLAG_DE_HIGH | DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE,
+ .panel_regs = wl_355608_a8_panel_regs,
+ .panel_regs_len = ARRAY_SIZE(wl_355608_a8_panel_regs),
+};
+
static const struct spi_device_id nv3052c_ids[] = {
{ "ltk035c5444t", },
{ "fs035vg158", },
+ { "wl-355608-a8", },
{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(spi, nv3052c_ids);
@@ -702,6 +925,7 @@ MODULE_DEVICE_TABLE(spi, nv3052c_ids);
static const struct of_device_id nv3052c_of_match[] = {
{ .compatible = "leadtek,ltk035c5444t", .data = <k035c5444t_panel_info },
{ .compatible = "fascontek,fs035vg158", .data = &fs035vg158_panel_info },
+ { .compatible = "wl-355608-a8", .data = &wl_355608_a8_panel_info },
{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(of, nv3052c_of_match);
@@ -719,4 +943,5 @@ module_spi_driver(nv3052c_driver);
MODULE_AUTHOR("Paul Cercueil <paul@crapouillou.net>");
MODULE_AUTHOR("Christophe Branchereau <cbranchereau@gmail.com>");
+MODULE_AUTHOR("Ryan Walklin <ryan@testtoast.com");
MODULE_LICENSE("GPL v2");
--
2.45.1
next prev parent reply other threads:[~2024-05-30 21:15 UTC|newest]
Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-05-30 21:12 [PATCH v3 0/2] Add WL-355608-A8 panel Ryan Walklin
2024-05-30 21:12 ` [PATCH v3 1/2] dt-bindings: display: panel: " Ryan Walklin
2024-06-06 9:32 ` Maxime Ripard
2024-06-06 9:37 ` Neil Armstrong
2024-06-06 9:48 ` Ryan Walklin
2024-06-06 11:24 ` Maxime Ripard
2024-06-06 11:23 ` Maxime Ripard
2024-06-06 11:51 ` Conor Dooley
2024-06-18 9:04 ` Maxime Ripard
2024-06-18 11:13 ` Conor Dooley
2024-06-18 12:05 ` Neil Armstrong
2024-06-26 8:56 ` Maxime Ripard
2024-06-26 9:10 ` Ryan Walklin
2024-06-26 9:16 ` Neil Armstrong
2024-06-26 11:00 ` Ryan Walklin
2024-06-06 13:49 ` Neil Armstrong
2024-05-30 21:12 ` Ryan Walklin [this message]
2024-06-03 8:39 ` [PATCH v3 2/2] drm: panel: nv3052c: " Neil Armstrong
2024-06-03 8:46 ` [PATCH v3 0/2] " Neil Armstrong
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20240530211415.44201-4-ryan@testtoast.com \
--to=ryan@testtoast.com \
--cc=airlied@gmail.com \
--cc=andre.przywara@arm.com \
--cc=conor+dt@kernel.org \
--cc=contact@jookia.org \
--cc=daniel@ffwll.ch \
--cc=devicetree@vger.kernel.org \
--cc=dri-devel@lists.freedesktop.org \
--cc=kikuchan98@gmail.com \
--cc=krzk+dt@kernel.org \
--cc=maarten.lankhorst@linux.intel.com \
--cc=macroalpha82@gmail.com \
--cc=mripard@kernel.org \
--cc=neil.armstrong@linaro.org \
--cc=quic_jesszhan@quicinc.com \
--cc=robh@kernel.org \
--cc=sam@ravnborg.org \
--cc=tzimmermann@suse.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).