From: Christophe Roullier <christophe.roullier@foss.st.com>
To: "David S . Miller" <davem@davemloft.net>,
Eric Dumazet <edumazet@google.com>,
Jakub Kicinski <kuba@kernel.org>, Paolo Abeni <pabeni@redhat.com>,
Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
Conor Dooley <conor+dt@kernel.org>,
Maxime Coquelin <mcoquelin.stm32@gmail.com>,
Alexandre Torgue <alexandre.torgue@foss.st.com>,
Richard Cochran <richardcochran@gmail.com>,
Jose Abreu <joabreu@synopsys.com>,
Liam Girdwood <lgirdwood@gmail.com>,
Mark Brown <broonie@kernel.org>,
Christophe Roullier <christophe.roullier@foss.st.com>,
Marek Vasut <marex@denx.de>
Cc: <netdev@vger.kernel.org>, <devicetree@vger.kernel.org>,
<linux-stm32@st-md-mailman.stormreply.com>,
<linux-arm-kernel@lists.infradead.org>,
<linux-kernel@vger.kernel.org>
Subject: [net-next,PATCH v6 8/8] net: stmmac: dwmac-stm32: add management of stm32mp13 for stm32
Date: Mon, 10 Jun 2024 09:14:59 +0200 [thread overview]
Message-ID: <20240610071459.287500-9-christophe.roullier@foss.st.com> (raw)
In-Reply-To: <20240610071459.287500-1-christophe.roullier@foss.st.com>
Add Ethernet support for STM32MP13.
STM32MP13 is STM32 SOC with 2 GMACs instances.
GMAC IP version is SNPS 4.20.
GMAC IP configure with 1 RX and 1 TX queue.
DMA HW capability register supported
RX Checksum Offload Engine supported
TX Checksum insertion supported
Wake-Up On Lan supported
TSO supported
Signed-off-by: Christophe Roullier <christophe.roullier@foss.st.com>
---
.../net/ethernet/stmicro/stmmac/dwmac-stm32.c | 24 +++++++++++++++++--
1 file changed, 22 insertions(+), 2 deletions(-)
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c
index 09ff0be0bdcdc..b8b3e04ca3ec8 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c
@@ -104,6 +104,7 @@ struct stm32_ops {
int (*parse_data)(struct stm32_dwmac *dwmac,
struct device *dev);
bool clk_rx_enable_in_suspend;
+ bool is_mp13;
u32 syscfg_clr_off;
};
@@ -224,11 +225,18 @@ static int stm32mp1_configure_pmcr(struct plat_stmmacenet_data *plat_dat)
{
struct stm32_dwmac *dwmac = plat_dat->bsp_priv;
u32 reg = dwmac->mode_reg;
- int val;
+ int val = 0;
switch (plat_dat->mac_interface) {
case PHY_INTERFACE_MODE_MII:
- val = SYSCFG_PMCR_ETH_SEL_MII;
+ /*
+ * STM32MP15xx supports both MII and GMII, STM32MP13xx MII only.
+ * SYSCFG_PMCSETR ETH_SELMII is present only on STM32MP15xx and
+ * acts as a selector between 0:GMII and 1:MII. As STM32MP13xx
+ * supports only MII, ETH_SELMII is not present.
+ */
+ if (!dwmac->ops->is_mp13) /* Select MII mode on STM32MP15xx */
+ val |= SYSCFG_PMCR_ETH_SEL_MII;
break;
case PHY_INTERFACE_MODE_GMII:
val = SYSCFG_PMCR_ETH_SEL_GMII;
@@ -560,12 +568,24 @@ static struct stm32_ops stm32mp1_dwmac_data = {
.resume = stm32mp1_resume,
.parse_data = stm32mp1_parse_data,
.syscfg_clr_off = 0x44,
+ .is_mp13 = false,
+ .clk_rx_enable_in_suspend = true
+};
+
+static struct stm32_ops stm32mp13_dwmac_data = {
+ .set_mode = stm32mp1_set_mode,
+ .suspend = stm32mp1_suspend,
+ .resume = stm32mp1_resume,
+ .parse_data = stm32mp1_parse_data,
+ .syscfg_clr_off = 0x08,
+ .is_mp13 = true,
.clk_rx_enable_in_suspend = true
};
static const struct of_device_id stm32_dwmac_match[] = {
{ .compatible = "st,stm32-dwmac", .data = &stm32mcu_dwmac_data},
{ .compatible = "st,stm32mp1-dwmac", .data = &stm32mp1_dwmac_data},
+ { .compatible = "st,stm32mp13-dwmac", .data = &stm32mp13_dwmac_data},
{ }
};
MODULE_DEVICE_TABLE(of, stm32_dwmac_match);
--
2.25.1
next prev parent reply other threads:[~2024-06-10 7:18 UTC|newest]
Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-06-10 7:14 [net-next,PATCH v6 0/8] Series to deliver Ethernet for STM32MP13 Christophe Roullier
2024-06-10 7:14 ` [net-next,PATCH v6 1/8] dt-bindings: net: add STM32MP13 compatible in documentation for stm32 Christophe Roullier
2024-06-10 16:26 ` Conor Dooley
2024-06-10 7:14 ` [net-next,PATCH v6 2/8] net: stmmac: dwmac-stm32: Separate out external clock rate validation Christophe Roullier
2024-06-10 7:14 ` [net-next,PATCH v6 3/8] net: stmmac: dwmac-stm32: Separate out external clock selector Christophe Roullier
2024-06-10 7:14 ` [net-next,PATCH v6 4/8] net: stmmac: dwmac-stm32: Extract PMCR configuration Christophe Roullier
2024-06-10 7:14 ` [net-next,PATCH v6 5/8] net: stmmac: dwmac-stm32: Clean up the debug prints Christophe Roullier
2024-06-10 7:14 ` [net-next,PATCH v6 6/8] net: stmmac: dwmac-stm32: Fix Mhz to MHz Christophe Roullier
2024-06-10 7:14 ` [net-next,PATCH v6 7/8] net: stmmac: dwmac-stm32: Mask support for PMCR configuration Christophe Roullier
2024-06-10 10:39 ` Marek Vasut
2024-06-10 11:45 ` Christophe ROULLIER
2024-06-10 13:43 ` Marek Vasut
2024-06-10 13:49 ` Christophe ROULLIER
2024-06-10 17:29 ` Marek Vasut
2024-06-11 6:42 ` Christophe ROULLIER
2024-06-10 7:14 ` Christophe Roullier [this message]
2024-06-10 10:40 ` [net-next,PATCH v6 8/8] net: stmmac: dwmac-stm32: add management of stm32mp13 for stm32 Marek Vasut
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20240610071459.287500-9-christophe.roullier@foss.st.com \
--to=christophe.roullier@foss.st.com \
--cc=alexandre.torgue@foss.st.com \
--cc=broonie@kernel.org \
--cc=conor+dt@kernel.org \
--cc=davem@davemloft.net \
--cc=devicetree@vger.kernel.org \
--cc=edumazet@google.com \
--cc=joabreu@synopsys.com \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=kuba@kernel.org \
--cc=lgirdwood@gmail.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-stm32@st-md-mailman.stormreply.com \
--cc=marex@denx.de \
--cc=mcoquelin.stm32@gmail.com \
--cc=netdev@vger.kernel.org \
--cc=pabeni@redhat.com \
--cc=richardcochran@gmail.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).