[net-next,PATCH v7 0/8] Series to deliver Ethernet for STM32MP13

[net-next,PATCH v7 0/8] Series to deliver Ethernet for STM32MP13

[Christophe Roullier]

STM32MP13 is STM32 SOC with 2 GMACs instances
    GMAC IP version is SNPS 4.20.
    GMAC IP configure with 1 RX and 1 TX queue.
    DMA HW capability register supported
    RX Checksum Offload Engine supported
    TX Checksum insertion supported
    Wake-Up On Lan supported
    TSO supported
Rework dwmac glue to simplify management for next stm32 (integrate RFC from Marek)

V2: - Remark from Rob Herring (add Krzysztof's ack in patch 02/11, update in yaml)
      Remark from Serge Semin (upate commits msg)
V3: - Remove PHY regulator patch and Ethernet2 DT because need to clarify how to
      manage PHY regulator (in glue or PHY side)
    - Integrate RFC from Marek
    - Remark from Rob Herring in YAML documentation
V4: - Remark from Marek (remove max-speed, extra space in DT, update commit msg)
    - Remark from Rasmus (add sign-off, add base-commit)
    - Remark from Sai Krishna Gajula
V5: - Fix warning during build CHECK_DTBS
    - Remark from Marek (glue + DT update)
    - Remark from Krzysztof about YAML (Make it symmetric)
V6: - Replace pr_debug by dev_dbg
    - Split serie driver/DTs separately
V7: - Remark from Marek (update sysconfig register mask)

Christophe Roullier (3):
  dt-bindings: net: add STM32MP13 compatible in documentation for stm32
  net: stmmac: dwmac-stm32: Mask support for PMCR configuration
  net: stmmac: dwmac-stm32: add management of stm32mp13 for stm32

Marek Vasut (5):
  net: stmmac: dwmac-stm32: Separate out external clock rate validation
  net: stmmac: dwmac-stm32: Separate out external clock selector
  net: stmmac: dwmac-stm32: Extract PMCR configuration
  net: stmmac: dwmac-stm32: Clean up the debug prints
  net: stmmac: dwmac-stm32: Fix Mhz to MHz

 .../devicetree/bindings/net/stm32-dwmac.yaml  |  43 ++++-
 .../net/ethernet/stmicro/stmmac/dwmac-stm32.c | 178 ++++++++++++++----
 2 files changed, 173 insertions(+), 48 deletions(-)


base-commit: bb678f01804ccaa861b012b2b9426d69673d8a84
-- 
2.25.1

[net-next,PATCH v7 1/8] dt-bindings: net: add STM32MP13 compatible in documentation for stm32

[Christophe Roullier]

New STM32 SOC have 2 GMACs instances.
GMAC IP version is SNPS 4.20.

Signed-off-by: Christophe Roullier <christophe.roullier@foss.st.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
---
 .../devicetree/bindings/net/stm32-dwmac.yaml  | 43 ++++++++++++++++---
 1 file changed, 36 insertions(+), 7 deletions(-)

diff --git a/Documentation/devicetree/bindings/net/stm32-dwmac.yaml b/Documentation/devicetree/bindings/net/stm32-dwmac.yaml
index 7ccf75676b6d5..f6e5e0626a3fb 100644
--- a/Documentation/devicetree/bindings/net/stm32-dwmac.yaml
+++ b/Documentation/devicetree/bindings/net/stm32-dwmac.yaml
@@ -22,18 +22,17 @@ select:
         enum:
           - st,stm32-dwmac
           - st,stm32mp1-dwmac
+          - st,stm32mp13-dwmac
   required:
     - compatible
 
-allOf:
-  - $ref: snps,dwmac.yaml#
-
 properties:
   compatible:
     oneOf:
       - items:
           - enum:
               - st,stm32mp1-dwmac
+              - st,stm32mp13-dwmac
           - const: snps,dwmac-4.20a
       - items:
           - enum:
@@ -75,12 +74,15 @@ properties:
   st,syscon:
     $ref: /schemas/types.yaml#/definitions/phandle-array
     items:
-      - items:
+      - minItems: 2
+        items:
           - description: phandle to the syscon node which encompases the glue register
           - description: offset of the control register
+          - description: field to set mask in register
     description:
       Should be phandle/offset pair. The phandle to the syscon node which
-      encompases the glue register, and the offset of the control register
+      encompases the glue register, the offset of the control register and
+      the mask to set bitfield in control register
 
   st,ext-phyclk:
     description:
@@ -112,12 +114,39 @@ required:
 
 unevaluatedProperties: false
 
+allOf:
+  - $ref: snps,dwmac.yaml#
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - st,stm32mp1-dwmac
+              - st,stm32-dwmac
+    then:
+      properties:
+        st,syscon:
+          items:
+            minItems: 2
+            maxItems: 2
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - st,stm32mp13-dwmac
+    then:
+      properties:
+        st,syscon:
+          items:
+            minItems: 3
+            maxItems: 3
+
 examples:
   - |
     #include <dt-bindings/interrupt-controller/arm-gic.h>
     #include <dt-bindings/clock/stm32mp1-clks.h>
-    #include <dt-bindings/reset/stm32mp1-resets.h>
-    #include <dt-bindings/mfd/stm32h7-rcc.h>
     //Example 1
      ethernet0: ethernet@5800a000 {
            compatible = "st,stm32mp1-dwmac", "snps,dwmac-4.20a";
-- 
2.25.1

[net-next,PATCH v7 2/8] net: stmmac: dwmac-stm32: Separate out external clock rate validation

[Christophe Roullier]

From: Marek Vasut <marex@denx.de>

Pull the external clock frequency validation into a separate function,
to avoid conflating it with external clock DT property decoding and
clock mux register configuration. This should make the code easier to
read and understand.

This does change the code behavior slightly. The clock mux PMCR register
setting now depends solely on the DT properties which configure the clock
mux between external clock and internal RCC generated clock. The mux PMCR
register settings no longer depend on the supplied clock frequency, that
supplied clock frequency is now only validated, and if the clock frequency
is invalid for a mode, it is rejected.

Previously, the code would switch the PMCR register clock mux to internal
RCC generated clock if external clock couldn't provide suitable frequency,
without checking whether the RCC generated clock frequency is correct. Such
behavior is risky at best, user should have configured their clock correctly
in the first place, so this behavior is removed here.

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Christophe Roullier <christophe.roullier@foss.st.com>
---
 .../net/ethernet/stmicro/stmmac/dwmac-stm32.c | 51 +++++++++++++++----
 1 file changed, 41 insertions(+), 10 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c
index c92dfc4ecf570..2fd2620ebed69 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c
@@ -157,25 +157,54 @@ static int stm32_dwmac_init(struct plat_stmmacenet_data *plat_dat, bool resume)
 	return stm32_dwmac_clk_enable(dwmac, resume);
 }
 
+static int stm32mp1_validate_ethck_rate(struct plat_stmmacenet_data *plat_dat)
+{
+	struct stm32_dwmac *dwmac = plat_dat->bsp_priv;
+	const u32 clk_rate = clk_get_rate(dwmac->clk_eth_ck);
+
+	switch (plat_dat->mac_interface) {
+	case PHY_INTERFACE_MODE_MII:
+	case PHY_INTERFACE_MODE_GMII:
+		if (clk_rate == ETH_CK_F_25M)
+			return 0;
+		break;
+	case PHY_INTERFACE_MODE_RMII:
+		if (clk_rate == ETH_CK_F_25M || clk_rate == ETH_CK_F_50M)
+			return 0;
+		break;
+	case PHY_INTERFACE_MODE_RGMII:
+	case PHY_INTERFACE_MODE_RGMII_ID:
+	case PHY_INTERFACE_MODE_RGMII_RXID:
+	case PHY_INTERFACE_MODE_RGMII_TXID:
+		if (clk_rate == ETH_CK_F_25M || clk_rate == ETH_CK_F_125M)
+			return 0;
+		break;
+	default:
+		break;
+	}
+
+	dev_err(dwmac->dev, "Mode %s does not match eth-ck frequency %d Hz",
+		phy_modes(plat_dat->mac_interface), clk_rate);
+	return -EINVAL;
+}
+
 static int stm32mp1_set_mode(struct plat_stmmacenet_data *plat_dat)
 {
 	struct stm32_dwmac *dwmac = plat_dat->bsp_priv;
-	u32 reg = dwmac->mode_reg, clk_rate;
-	int val;
+	u32 reg = dwmac->mode_reg;
+	int val, ret;
 
-	clk_rate = clk_get_rate(dwmac->clk_eth_ck);
 	dwmac->enable_eth_ck = false;
 	switch (plat_dat->mac_interface) {
 	case PHY_INTERFACE_MODE_MII:
-		if (clk_rate == ETH_CK_F_25M && dwmac->ext_phyclk)
+		if (dwmac->ext_phyclk)
 			dwmac->enable_eth_ck = true;
 		val = SYSCFG_PMCR_ETH_SEL_MII;
 		pr_debug("SYSCFG init : PHY_INTERFACE_MODE_MII\n");
 		break;
 	case PHY_INTERFACE_MODE_GMII:
 		val = SYSCFG_PMCR_ETH_SEL_GMII;
-		if (clk_rate == ETH_CK_F_25M &&
-		    (dwmac->eth_clk_sel_reg || dwmac->ext_phyclk)) {
+		if (dwmac->eth_clk_sel_reg || dwmac->ext_phyclk) {
 			dwmac->enable_eth_ck = true;
 			val |= SYSCFG_PMCR_ETH_CLK_SEL;
 		}
@@ -183,8 +212,7 @@ static int stm32mp1_set_mode(struct plat_stmmacenet_data *plat_dat)
 		break;
 	case PHY_INTERFACE_MODE_RMII:
 		val = SYSCFG_PMCR_ETH_SEL_RMII;
-		if ((clk_rate == ETH_CK_F_25M || clk_rate == ETH_CK_F_50M) &&
-		    (dwmac->eth_ref_clk_sel_reg || dwmac->ext_phyclk)) {
+		if (dwmac->eth_ref_clk_sel_reg || dwmac->ext_phyclk) {
 			dwmac->enable_eth_ck = true;
 			val |= SYSCFG_PMCR_ETH_REF_CLK_SEL;
 		}
@@ -195,8 +223,7 @@ static int stm32mp1_set_mode(struct plat_stmmacenet_data *plat_dat)
 	case PHY_INTERFACE_MODE_RGMII_RXID:
 	case PHY_INTERFACE_MODE_RGMII_TXID:
 		val = SYSCFG_PMCR_ETH_SEL_RGMII;
-		if ((clk_rate == ETH_CK_F_25M || clk_rate == ETH_CK_F_125M) &&
-		    (dwmac->eth_clk_sel_reg || dwmac->ext_phyclk)) {
+		if (dwmac->eth_clk_sel_reg || dwmac->ext_phyclk) {
 			dwmac->enable_eth_ck = true;
 			val |= SYSCFG_PMCR_ETH_CLK_SEL;
 		}
@@ -209,6 +236,10 @@ static int stm32mp1_set_mode(struct plat_stmmacenet_data *plat_dat)
 		return -EINVAL;
 	}
 
+	ret = stm32mp1_validate_ethck_rate(plat_dat);
+	if (ret)
+		return ret;
+
 	/* Need to update PMCCLRR (clear register) */
 	regmap_write(dwmac->regmap, reg + SYSCFG_PMCCLRR_OFFSET,
 		     dwmac->ops->syscfg_eth_mask);
-- 
2.25.1

[net-next,PATCH v7 3/8] net: stmmac: dwmac-stm32: Separate out external clock selector

[Christophe Roullier]

From: Marek Vasut <marex@denx.de>

Pull the external clock selector into a separate function, to avoid
conflating it with external clock rate validation and clock mux
register configuration. This should make the code easier to read and
understand.

The dwmac->enable_eth_ck variable in the end indicates whether the MAC
clock are supplied by external oscillator (true) or internal RCC clock
IP (false). The dwmac->enable_eth_ck value is set based on multiple DT
properties, some of them deprecated, some of them specific to bus mode.

The following DT properties and variables are taken into account. In
each case, if the property is present or true, MAC clock is supplied
by external oscillator.
- "st,ext-phyclk", assigned to variable dwmac->ext_phyclk
  - Used in any mode (MII/RMII/GMII/RGMII)
  - The only non-deprecated DT property of the three
- "st,eth-clk-sel", assigned to variable dwmac->eth_clk_sel_reg
  - Valid only in GMII/RGMII mode
  - Deprecated property, backward compatibility only
- "st,eth-ref-clk-sel", assigned to variable dwmac->eth_ref_clk_sel_reg
  - Valid only in RMII mode
  - Deprecated property, backward compatibility only

The stm32mp1_select_ethck_external() function handles the aforementioned
DT properties and sets dwmac->enable_eth_ck accordingly.

The stm32mp1_set_mode() is adjusted to call stm32mp1_select_ethck_external()
first and then only use dwmac->enable_eth_ck to determine hardware clock mux
settings.

No functional change intended.

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Christophe Roullier <christophe.roullier@foss.st.com>
---
 .../net/ethernet/stmicro/stmmac/dwmac-stm32.c | 50 ++++++++++++++-----
 1 file changed, 38 insertions(+), 12 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c
index 2fd2620ebed69..767994061ea82 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c
@@ -157,6 +157,37 @@ static int stm32_dwmac_init(struct plat_stmmacenet_data *plat_dat, bool resume)
 	return stm32_dwmac_clk_enable(dwmac, resume);
 }
 
+static int stm32mp1_select_ethck_external(struct plat_stmmacenet_data *plat_dat)
+{
+	struct stm32_dwmac *dwmac = plat_dat->bsp_priv;
+
+	switch (plat_dat->mac_interface) {
+	case PHY_INTERFACE_MODE_MII:
+		dwmac->enable_eth_ck = dwmac->ext_phyclk;
+		return 0;
+	case PHY_INTERFACE_MODE_GMII:
+		dwmac->enable_eth_ck = dwmac->eth_clk_sel_reg ||
+				       dwmac->ext_phyclk;
+		return 0;
+	case PHY_INTERFACE_MODE_RMII:
+		dwmac->enable_eth_ck = dwmac->eth_ref_clk_sel_reg ||
+				       dwmac->ext_phyclk;
+		return 0;
+	case PHY_INTERFACE_MODE_RGMII:
+	case PHY_INTERFACE_MODE_RGMII_ID:
+	case PHY_INTERFACE_MODE_RGMII_RXID:
+	case PHY_INTERFACE_MODE_RGMII_TXID:
+		dwmac->enable_eth_ck = dwmac->eth_clk_sel_reg ||
+				       dwmac->ext_phyclk;
+		return 0;
+	default:
+		dwmac->enable_eth_ck = false;
+		dev_err(dwmac->dev, "Mode %s not supported",
+			phy_modes(plat_dat->mac_interface));
+		return -EINVAL;
+	}
+}
+
 static int stm32mp1_validate_ethck_rate(struct plat_stmmacenet_data *plat_dat)
 {
 	struct stm32_dwmac *dwmac = plat_dat->bsp_priv;
@@ -194,28 +225,25 @@ static int stm32mp1_set_mode(struct plat_stmmacenet_data *plat_dat)
 	u32 reg = dwmac->mode_reg;
 	int val, ret;
 
-	dwmac->enable_eth_ck = false;
+	ret = stm32mp1_select_ethck_external(plat_dat);
+	if (ret)
+		return ret;
+
 	switch (plat_dat->mac_interface) {
 	case PHY_INTERFACE_MODE_MII:
-		if (dwmac->ext_phyclk)
-			dwmac->enable_eth_ck = true;
 		val = SYSCFG_PMCR_ETH_SEL_MII;
 		pr_debug("SYSCFG init : PHY_INTERFACE_MODE_MII\n");
 		break;
 	case PHY_INTERFACE_MODE_GMII:
 		val = SYSCFG_PMCR_ETH_SEL_GMII;
-		if (dwmac->eth_clk_sel_reg || dwmac->ext_phyclk) {
-			dwmac->enable_eth_ck = true;
+		if (dwmac->enable_eth_ck)
 			val |= SYSCFG_PMCR_ETH_CLK_SEL;
-		}
 		pr_debug("SYSCFG init : PHY_INTERFACE_MODE_GMII\n");
 		break;
 	case PHY_INTERFACE_MODE_RMII:
 		val = SYSCFG_PMCR_ETH_SEL_RMII;
-		if (dwmac->eth_ref_clk_sel_reg || dwmac->ext_phyclk) {
-			dwmac->enable_eth_ck = true;
+		if (dwmac->enable_eth_ck)
 			val |= SYSCFG_PMCR_ETH_REF_CLK_SEL;
-		}
 		pr_debug("SYSCFG init : PHY_INTERFACE_MODE_RMII\n");
 		break;
 	case PHY_INTERFACE_MODE_RGMII:
@@ -223,10 +251,8 @@ static int stm32mp1_set_mode(struct plat_stmmacenet_data *plat_dat)
 	case PHY_INTERFACE_MODE_RGMII_RXID:
 	case PHY_INTERFACE_MODE_RGMII_TXID:
 		val = SYSCFG_PMCR_ETH_SEL_RGMII;
-		if (dwmac->eth_clk_sel_reg || dwmac->ext_phyclk) {
-			dwmac->enable_eth_ck = true;
+		if (dwmac->enable_eth_ck)
 			val |= SYSCFG_PMCR_ETH_CLK_SEL;
-		}
 		pr_debug("SYSCFG init : PHY_INTERFACE_MODE_RGMII\n");
 		break;
 	default:
-- 
2.25.1

[net-next,PATCH v7 4/8] net: stmmac: dwmac-stm32: Extract PMCR configuration

[Christophe Roullier]

From: Marek Vasut <marex@denx.de>

Pull the PMCR clock mux configuration into a separate function. This is
the final change of three, which moves external clock rate validation,
external clock selector decoding, and clock mux configuration into
separate functions. This should make the code easier to understand.
No functional change intended.

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Christophe Roullier <christophe.roullier@foss.st.com>
---
 .../net/ethernet/stmicro/stmmac/dwmac-stm32.c | 27 ++++++++++++-------
 1 file changed, 17 insertions(+), 10 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c
index 767994061ea82..aa413edd1ef71 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c
@@ -219,15 +219,11 @@ static int stm32mp1_validate_ethck_rate(struct plat_stmmacenet_data *plat_dat)
 	return -EINVAL;
 }
 
-static int stm32mp1_set_mode(struct plat_stmmacenet_data *plat_dat)
+static int stm32mp1_configure_pmcr(struct plat_stmmacenet_data *plat_dat)
 {
 	struct stm32_dwmac *dwmac = plat_dat->bsp_priv;
 	u32 reg = dwmac->mode_reg;
-	int val, ret;
-
-	ret = stm32mp1_select_ethck_external(plat_dat);
-	if (ret)
-		return ret;
+	int val;
 
 	switch (plat_dat->mac_interface) {
 	case PHY_INTERFACE_MODE_MII:
@@ -262,10 +258,6 @@ static int stm32mp1_set_mode(struct plat_stmmacenet_data *plat_dat)
 		return -EINVAL;
 	}
 
-	ret = stm32mp1_validate_ethck_rate(plat_dat);
-	if (ret)
-		return ret;
-
 	/* Need to update PMCCLRR (clear register) */
 	regmap_write(dwmac->regmap, reg + SYSCFG_PMCCLRR_OFFSET,
 		     dwmac->ops->syscfg_eth_mask);
@@ -275,6 +267,21 @@ static int stm32mp1_set_mode(struct plat_stmmacenet_data *plat_dat)
 				 dwmac->ops->syscfg_eth_mask, val);
 }
 
+static int stm32mp1_set_mode(struct plat_stmmacenet_data *plat_dat)
+{
+	int ret;
+
+	ret = stm32mp1_select_ethck_external(plat_dat);
+	if (ret)
+		return ret;
+
+	ret = stm32mp1_validate_ethck_rate(plat_dat);
+	if (ret)
+		return ret;
+
+	return stm32mp1_configure_pmcr(plat_dat);
+}
+
 static int stm32mcu_set_mode(struct plat_stmmacenet_data *plat_dat)
 {
 	struct stm32_dwmac *dwmac = plat_dat->bsp_priv;
-- 
2.25.1

[net-next,PATCH v7 5/8] net: stmmac: dwmac-stm32: Clean up the debug prints

[Christophe Roullier]

From: Marek Vasut <marex@denx.de>

Use dev_err()/dev_dbg() and phy_modes() to print PHY mode instead of
pr_debug() and hand-written PHY mode decoding. This way, each debug
print has associated device with it and duplicated mode decoding is
removed.

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Christophe Roullier <christophe.roullier@foss.st.com>
---
 .../net/ethernet/stmicro/stmmac/dwmac-stm32.c  | 18 ++++++++----------
 1 file changed, 8 insertions(+), 10 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c
index aa413edd1ef71..75981ac2cbb56 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c
@@ -228,19 +228,16 @@ static int stm32mp1_configure_pmcr(struct plat_stmmacenet_data *plat_dat)
 	switch (plat_dat->mac_interface) {
 	case PHY_INTERFACE_MODE_MII:
 		val = SYSCFG_PMCR_ETH_SEL_MII;
-		pr_debug("SYSCFG init : PHY_INTERFACE_MODE_MII\n");
 		break;
 	case PHY_INTERFACE_MODE_GMII:
 		val = SYSCFG_PMCR_ETH_SEL_GMII;
 		if (dwmac->enable_eth_ck)
 			val |= SYSCFG_PMCR_ETH_CLK_SEL;
-		pr_debug("SYSCFG init : PHY_INTERFACE_MODE_GMII\n");
 		break;
 	case PHY_INTERFACE_MODE_RMII:
 		val = SYSCFG_PMCR_ETH_SEL_RMII;
 		if (dwmac->enable_eth_ck)
 			val |= SYSCFG_PMCR_ETH_REF_CLK_SEL;
-		pr_debug("SYSCFG init : PHY_INTERFACE_MODE_RMII\n");
 		break;
 	case PHY_INTERFACE_MODE_RGMII:
 	case PHY_INTERFACE_MODE_RGMII_ID:
@@ -249,15 +246,16 @@ static int stm32mp1_configure_pmcr(struct plat_stmmacenet_data *plat_dat)
 		val = SYSCFG_PMCR_ETH_SEL_RGMII;
 		if (dwmac->enable_eth_ck)
 			val |= SYSCFG_PMCR_ETH_CLK_SEL;
-		pr_debug("SYSCFG init : PHY_INTERFACE_MODE_RGMII\n");
 		break;
 	default:
-		pr_debug("SYSCFG init :  Do not manage %d interface\n",
-			 plat_dat->mac_interface);
+		dev_err(dwmac->dev, "Mode %s not supported",
+			phy_modes(plat_dat->mac_interface));
 		/* Do not manage others interfaces */
 		return -EINVAL;
 	}
 
+	dev_dbg(dwmac->dev, "Mode %s", phy_modes(plat_dat->mac_interface));
+
 	/* Need to update PMCCLRR (clear register) */
 	regmap_write(dwmac->regmap, reg + SYSCFG_PMCCLRR_OFFSET,
 		     dwmac->ops->syscfg_eth_mask);
@@ -291,19 +289,19 @@ static int stm32mcu_set_mode(struct plat_stmmacenet_data *plat_dat)
 	switch (plat_dat->mac_interface) {
 	case PHY_INTERFACE_MODE_MII:
 		val = SYSCFG_MCU_ETH_SEL_MII;
-		pr_debug("SYSCFG init : PHY_INTERFACE_MODE_MII\n");
 		break;
 	case PHY_INTERFACE_MODE_RMII:
 		val = SYSCFG_MCU_ETH_SEL_RMII;
-		pr_debug("SYSCFG init : PHY_INTERFACE_MODE_RMII\n");
 		break;
 	default:
-		pr_debug("SYSCFG init :  Do not manage %d interface\n",
-			 plat_dat->mac_interface);
+		dev_err(dwmac->dev, "Mode %s not supported",
+			phy_modes(plat_dat->mac_interface));
 		/* Do not manage others interfaces */
 		return -EINVAL;
 	}
 
+	dev_dbg(dwmac->dev, "Mode %s", phy_modes(plat_dat->mac_interface));
+
 	return regmap_update_bits(dwmac->regmap, reg,
 				 dwmac->ops->syscfg_eth_mask, val << 23);
 }
-- 
2.25.1

[net-next,PATCH v7 6/8] net: stmmac: dwmac-stm32: Fix Mhz to MHz

[Christophe Roullier]

From: Marek Vasut <marex@denx.de>

Trivial, fix up the comments using 'Mhz' to 'MHz'.
No functional change.

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Christophe Roullier <christophe.roullier@foss.st.com>
---
 drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c
index 75981ac2cbb56..bed2be129b2d2 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c
@@ -58,7 +58,7 @@
  * Below table summarizes the clock requirement and clock sources for
  * supported phy interface modes.
  * __________________________________________________________________________
- *|PHY_MODE | Normal | PHY wo crystal|   PHY wo crystal   |No 125Mhz from PHY|
+ *|PHY_MODE | Normal | PHY wo crystal|   PHY wo crystal   |No 125MHz from PHY|
  *|         |        |      25MHz    |        50MHz       |                  |
  * ---------------------------------------------------------------------------
  *|  MII    |	 -   |     eth-ck    |	      n/a	  |	  n/a        |
@@ -367,7 +367,7 @@ static int stm32mp1_parse_data(struct stm32_dwmac *dwmac,
 	/* Gigabit Ethernet 125MHz clock selection. */
 	dwmac->eth_clk_sel_reg = of_property_read_bool(np, "st,eth-clk-sel");
 
-	/* Ethernet 50Mhz RMII clock selection */
+	/* Ethernet 50MHz RMII clock selection */
 	dwmac->eth_ref_clk_sel_reg =
 		of_property_read_bool(np, "st,eth-ref-clk-sel");
 
-- 
2.25.1

[net-next,PATCH v7 7/8] net: stmmac: dwmac-stm32: Mask support for PMCR configuration

[Christophe Roullier]

Add possibility to have second argument in syscon property to manage
mask. This mask will be used to address right BITFIELDS of PMCR register.

Signed-off-by: Christophe Roullier <christophe.roullier@foss.st.com>
---
 .../net/ethernet/stmicro/stmmac/dwmac-stm32.c | 28 +++++++++++++------
 1 file changed, 19 insertions(+), 9 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c
index bed2be129b2d2..09ff0be0bdcdc 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c
@@ -90,6 +90,7 @@ struct stm32_dwmac {
 	int eth_ref_clk_sel_reg;
 	int irq_pwr_wakeup;
 	u32 mode_reg;		 /* MAC glue-logic mode register */
+	u32 mode_mask;
 	struct regmap *regmap;
 	u32 speed;
 	const struct stm32_ops *ops;
@@ -102,8 +103,8 @@ struct stm32_ops {
 	void (*resume)(struct stm32_dwmac *dwmac);
 	int (*parse_data)(struct stm32_dwmac *dwmac,
 			  struct device *dev);
-	u32 syscfg_eth_mask;
 	bool clk_rx_enable_in_suspend;
+	u32 syscfg_clr_off;
 };
 
 static int stm32_dwmac_clk_enable(struct stm32_dwmac *dwmac, bool resume)
@@ -256,13 +257,16 @@ static int stm32mp1_configure_pmcr(struct plat_stmmacenet_data *plat_dat)
 
 	dev_dbg(dwmac->dev, "Mode %s", phy_modes(plat_dat->mac_interface));
 
+	/* Shift value at correct ethernet MAC offset in SYSCFG_PMCSETR */
+	val <<= ffs(dwmac->mode_mask) - ffs(SYSCFG_MP1_ETH_MASK);
+
 	/* Need to update PMCCLRR (clear register) */
-	regmap_write(dwmac->regmap, reg + SYSCFG_PMCCLRR_OFFSET,
-		     dwmac->ops->syscfg_eth_mask);
+	regmap_write(dwmac->regmap, dwmac->ops->syscfg_clr_off,
+		     dwmac->mode_mask);
 
 	/* Update PMCSETR (set register) */
 	return regmap_update_bits(dwmac->regmap, reg,
-				 dwmac->ops->syscfg_eth_mask, val);
+				 dwmac->mode_mask, val);
 }
 
 static int stm32mp1_set_mode(struct plat_stmmacenet_data *plat_dat)
@@ -303,7 +307,7 @@ static int stm32mcu_set_mode(struct plat_stmmacenet_data *plat_dat)
 	dev_dbg(dwmac->dev, "Mode %s", phy_modes(plat_dat->mac_interface));
 
 	return regmap_update_bits(dwmac->regmap, reg,
-				 dwmac->ops->syscfg_eth_mask, val << 23);
+				 SYSCFG_MCU_ETH_MASK, val << 23);
 }
 
 static void stm32_dwmac_clk_disable(struct stm32_dwmac *dwmac, bool suspend)
@@ -348,8 +352,15 @@ static int stm32_dwmac_parse_data(struct stm32_dwmac *dwmac,
 		return PTR_ERR(dwmac->regmap);
 
 	err = of_property_read_u32_index(np, "st,syscon", 1, &dwmac->mode_reg);
-	if (err)
+	if (err) {
 		dev_err(dev, "Can't get sysconfig mode offset (%d)\n", err);
+		return err;
+	}
+
+	dwmac->mode_mask = SYSCFG_MP1_ETH_MASK;
+	err = of_property_read_u32_index(np, "st,syscon", 2, &dwmac->mode_mask);
+	if (err)
+		dev_dbg(dev, "Warning sysconfig register mask not set\n");
 
 	return err;
 }
@@ -540,8 +551,7 @@ static SIMPLE_DEV_PM_OPS(stm32_dwmac_pm_ops,
 	stm32_dwmac_suspend, stm32_dwmac_resume);
 
 static struct stm32_ops stm32mcu_dwmac_data = {
-	.set_mode = stm32mcu_set_mode,
-	.syscfg_eth_mask = SYSCFG_MCU_ETH_MASK
+	.set_mode = stm32mcu_set_mode
 };
 
 static struct stm32_ops stm32mp1_dwmac_data = {
@@ -549,7 +559,7 @@ static struct stm32_ops stm32mp1_dwmac_data = {
 	.suspend = stm32mp1_suspend,
 	.resume = stm32mp1_resume,
 	.parse_data = stm32mp1_parse_data,
-	.syscfg_eth_mask = SYSCFG_MP1_ETH_MASK,
+	.syscfg_clr_off = 0x44,
 	.clk_rx_enable_in_suspend = true
 };
 
-- 
2.25.1

[net-next,PATCH v7 8/8] net: stmmac: dwmac-stm32: add management of stm32mp13 for stm32

[Christophe Roullier]

Add Ethernet support for STM32MP13.
STM32MP13 is STM32 SOC with 2 GMACs instances.
GMAC IP version is SNPS 4.20.
GMAC IP configure with 1 RX and 1 TX queue.
DMA HW capability register supported
RX Checksum Offload Engine supported
TX Checksum insertion supported
Wake-Up On Lan supported
TSO supported

Signed-off-by: Christophe Roullier <christophe.roullier@foss.st.com>
---
 .../net/ethernet/stmicro/stmmac/dwmac-stm32.c | 32 ++++++++++++++++---
 1 file changed, 28 insertions(+), 4 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c
index 09ff0be0bdcdc..b2db0e26c4e45 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c
@@ -104,6 +104,7 @@ struct stm32_ops {
 	int (*parse_data)(struct stm32_dwmac *dwmac,
 			  struct device *dev);
 	bool clk_rx_enable_in_suspend;
+	bool is_mp13;
 	u32 syscfg_clr_off;
 };
 
@@ -224,11 +225,18 @@ static int stm32mp1_configure_pmcr(struct plat_stmmacenet_data *plat_dat)
 {
 	struct stm32_dwmac *dwmac = plat_dat->bsp_priv;
 	u32 reg = dwmac->mode_reg;
-	int val;
+	int val = 0;
 
 	switch (plat_dat->mac_interface) {
 	case PHY_INTERFACE_MODE_MII:
-		val = SYSCFG_PMCR_ETH_SEL_MII;
+		/*
+		 * STM32MP15xx supports both MII and GMII, STM32MP13xx MII only.
+		 * SYSCFG_PMCSETR ETH_SELMII is present only on STM32MP15xx and
+		 * acts as a selector between 0:GMII and 1:MII. As STM32MP13xx
+		 * supports only MII, ETH_SELMII is not present.
+		 */
+		if (!dwmac->ops->is_mp13)  /* Select MII mode on STM32MP15xx */
+			val |= SYSCFG_PMCR_ETH_SEL_MII;
 		break;
 	case PHY_INTERFACE_MODE_GMII:
 		val = SYSCFG_PMCR_ETH_SEL_GMII;
@@ -359,8 +367,12 @@ static int stm32_dwmac_parse_data(struct stm32_dwmac *dwmac,
 
 	dwmac->mode_mask = SYSCFG_MP1_ETH_MASK;
 	err = of_property_read_u32_index(np, "st,syscon", 2, &dwmac->mode_mask);
-	if (err)
-		dev_dbg(dev, "Warning sysconfig register mask not set\n");
+	if (err) {
+		if (dwmac->ops->is_mp13)
+			dev_err(dev, "Sysconfig register mask must be set (%d)\n", err);
+		else
+			dev_dbg(dev, "Warning sysconfig register mask not set\n");
+	}
 
 	return err;
 }
@@ -560,12 +572,24 @@ static struct stm32_ops stm32mp1_dwmac_data = {
 	.resume = stm32mp1_resume,
 	.parse_data = stm32mp1_parse_data,
 	.syscfg_clr_off = 0x44,
+	.is_mp13 = false,
+	.clk_rx_enable_in_suspend = true
+};
+
+static struct stm32_ops stm32mp13_dwmac_data = {
+	.set_mode = stm32mp1_set_mode,
+	.suspend = stm32mp1_suspend,
+	.resume = stm32mp1_resume,
+	.parse_data = stm32mp1_parse_data,
+	.syscfg_clr_off = 0x08,
+	.is_mp13 = true,
 	.clk_rx_enable_in_suspend = true
 };
 
 static const struct of_device_id stm32_dwmac_match[] = {
 	{ .compatible = "st,stm32-dwmac", .data = &stm32mcu_dwmac_data},
 	{ .compatible = "st,stm32mp1-dwmac", .data = &stm32mp1_dwmac_data},
+	{ .compatible = "st,stm32mp13-dwmac", .data = &stm32mp13_dwmac_data},
 	{ }
 };
 MODULE_DEVICE_TABLE(of, stm32_dwmac_match);
-- 
2.25.1

Re: [net-next,PATCH v7 7/8] net: stmmac: dwmac-stm32: Mask support for PMCR configuration

[Marek Vasut]

On 6/11/24 10:36 AM, Christophe Roullier wrote:

[...]

>   static void stm32_dwmac_clk_disable(struct stm32_dwmac *dwmac, bool suspend)
> @@ -348,8 +352,15 @@ static int stm32_dwmac_parse_data(struct stm32_dwmac *dwmac,
>   		return PTR_ERR(dwmac->regmap);
>   
>   	err = of_property_read_u32_index(np, "st,syscon", 1, &dwmac->mode_reg);
> -	if (err)
> +	if (err) {
>   		dev_err(dev, "Can't get sysconfig mode offset (%d)\n", err);
> +		return err;
> +	}
> +
> +	dwmac->mode_mask = SYSCFG_MP1_ETH_MASK;
> +	err = of_property_read_u32_index(np, "st,syscon", 2, &dwmac->mode_mask);
> +	if (err)
> +		dev_dbg(dev, "Warning sysconfig register mask not set\n");

My comment on V6 was not addressed I think ?

Re: [net-next,PATCH v7 7/8] net: stmmac: dwmac-stm32: Mask support for PMCR configuration

[Christophe ROULLIER]

On 6/11/24 15:07, Marek Vasut wrote:
> On 6/11/24 10:36 AM, Christophe Roullier wrote:
>
> [...]
>
>>   static void stm32_dwmac_clk_disable(struct stm32_dwmac *dwmac, bool 
>> suspend)
>> @@ -348,8 +352,15 @@ static int stm32_dwmac_parse_data(struct 
>> stm32_dwmac *dwmac,
>>           return PTR_ERR(dwmac->regmap);
>>         err = of_property_read_u32_index(np, "st,syscon", 1, 
>> &dwmac->mode_reg);
>> -    if (err)
>> +    if (err) {
>>           dev_err(dev, "Can't get sysconfig mode offset (%d)\n", err);
>> +        return err;
>> +    }
>> +
>> +    dwmac->mode_mask = SYSCFG_MP1_ETH_MASK;
>> +    err = of_property_read_u32_index(np, "st,syscon", 2, 
>> &dwmac->mode_mask);
>> +    if (err)
>> +        dev_dbg(dev, "Warning sysconfig register mask not set\n");
>
> My comment on V6 was not addressed I think ?

Hi Marek,

I put the modification in patch which introduce MP13 (V7 8/8) ;-)

  	err = of_property_read_u32_index(np, "st,syscon", 2, &dwmac->mode_mask);
-	if (err)
-		dev_dbg(dev, "Warning sysconfig register mask not set\n");
+	if (err) {
+		if (dwmac->ops->is_mp13)
+			dev_err(dev, "Sysconfig register mask must be set (%d)\n", err);
+		else
+			dev_dbg(dev, "Warning sysconfig register mask not set\n");
+	}

Re: [net-next,PATCH v7 7/8] net: stmmac: dwmac-stm32: Mask support for PMCR configuration

[Marek Vasut]

On 6/11/24 3:32 PM, Christophe ROULLIER wrote:
> 
> On 6/11/24 15:07, Marek Vasut wrote:
>> On 6/11/24 10:36 AM, Christophe Roullier wrote:
>>
>> [...]
>>
>>>   static void stm32_dwmac_clk_disable(struct stm32_dwmac *dwmac, bool 
>>> suspend)
>>> @@ -348,8 +352,15 @@ static int stm32_dwmac_parse_data(struct 
>>> stm32_dwmac *dwmac,
>>>           return PTR_ERR(dwmac->regmap);
>>>         err = of_property_read_u32_index(np, "st,syscon", 1, 
>>> &dwmac->mode_reg);
>>> -    if (err)
>>> +    if (err) {
>>>           dev_err(dev, "Can't get sysconfig mode offset (%d)\n", err);
>>> +        return err;
>>> +    }
>>> +
>>> +    dwmac->mode_mask = SYSCFG_MP1_ETH_MASK;
>>> +    err = of_property_read_u32_index(np, "st,syscon", 2, 
>>> &dwmac->mode_mask);
>>> +    if (err)
>>> +        dev_dbg(dev, "Warning sysconfig register mask not set\n");
>>
>> My comment on V6 was not addressed I think ?
> 
> Hi Marek,
> 
> I put the modification in patch which introduce MP13 (V7 8/8) ;-)
> 
>       err = of_property_read_u32_index(np, "st,syscon", 2, 
> &dwmac->mode_mask);
> -    if (err)
> -        dev_dbg(dev, "Warning sysconfig register mask not set\n");
> +    if (err) {
> +        if (dwmac->ops->is_mp13)
> +            dev_err(dev, "Sysconfig register mask must be set (%d)\n", 
> err);
> +        else
> +            dev_dbg(dev, "Warning sysconfig register mask not set\n");
> +    }

That isn't right, is it ?

For MP2 , this still checks the presence of syscon , which shouldn't be 
checked at all for MP2 as far as I understand it ?

Re: [net-next,PATCH v7 7/8] net: stmmac: dwmac-stm32: Mask support for PMCR configuration

[Christophe ROULLIER]

Hi Marek,

On 6/11/24 18:16, Marek Vasut wrote:
> On 6/11/24 3:32 PM, Christophe ROULLIER wrote:
>>
>> On 6/11/24 15:07, Marek Vasut wrote:
>>> On 6/11/24 10:36 AM, Christophe Roullier wrote:
>>>
>>> [...]
>>>
>>>>   static void stm32_dwmac_clk_disable(struct stm32_dwmac *dwmac, 
>>>> bool suspend)
>>>> @@ -348,8 +352,15 @@ static int stm32_dwmac_parse_data(struct 
>>>> stm32_dwmac *dwmac,
>>>>           return PTR_ERR(dwmac->regmap);
>>>>         err = of_property_read_u32_index(np, "st,syscon", 1, 
>>>> &dwmac->mode_reg);
>>>> -    if (err)
>>>> +    if (err) {
>>>>           dev_err(dev, "Can't get sysconfig mode offset (%d)\n", err);
>>>> +        return err;
>>>> +    }
>>>> +
>>>> +    dwmac->mode_mask = SYSCFG_MP1_ETH_MASK;
>>>> +    err = of_property_read_u32_index(np, "st,syscon", 2, 
>>>> &dwmac->mode_mask);
>>>> +    if (err)
>>>> +        dev_dbg(dev, "Warning sysconfig register mask not set\n");
>>>
>>> My comment on V6 was not addressed I think ?
>>
>> Hi Marek,
>>
>> I put the modification in patch which introduce MP13 (V7 8/8) ;-)
>>
>>       err = of_property_read_u32_index(np, "st,syscon", 2, 
>> &dwmac->mode_mask);
>> -    if (err)
>> -        dev_dbg(dev, "Warning sysconfig register mask not set\n");
>> +    if (err) {
>> +        if (dwmac->ops->is_mp13)
>> +            dev_err(dev, "Sysconfig register mask must be set 
>> (%d)\n", err);
>> +        else
>> +            dev_dbg(dev, "Warning sysconfig register mask not set\n");
>> +    }
>
> That isn't right, is it ?
>
> For MP2 , this still checks the presence of syscon , which shouldn't 
> be checked at all for MP2 as far as I understand it ?

When I will push MP2 serie, I will bypass the check of mask syscfg. I 
will push MP2 after MP13 ack.

Thanks

Re: [net-next,PATCH v7 7/8] net: stmmac: dwmac-stm32: Mask support for PMCR configuration

[Marek Vasut]

On 6/11/24 10:36 AM, Christophe Roullier wrote:
> Add possibility to have second argument in syscon property to manage
> mask. This mask will be used to address right BITFIELDS of PMCR register.
> 
> Signed-off-by: Christophe Roullier <christophe.roullier@foss.st.com>

Reviewed-by: Marek Vasut <marex@denx.de>

Re: [net-next,PATCH v7 8/8] net: stmmac: dwmac-stm32: add management of stm32mp13 for stm32

[Marek Vasut]

On 6/11/24 10:36 AM, Christophe Roullier wrote:
> Add Ethernet support for STM32MP13.
> STM32MP13 is STM32 SOC with 2 GMACs instances.
> GMAC IP version is SNPS 4.20.
> GMAC IP configure with 1 RX and 1 TX queue.
> DMA HW capability register supported
> RX Checksum Offload Engine supported
> TX Checksum insertion supported
> Wake-Up On Lan supported
> TSO supported
> 
> Signed-off-by: Christophe Roullier <christophe.roullier@foss.st.com>

Reviewed-by: Marek Vasut <marex@denx.de>

Re: [net-next,PATCH v7 0/8] Series to deliver Ethernet for STM32MP13

[patchwork-bot+netdevbpf]

Hello:

This series was applied to netdev/net-next.git (main)
by Paolo Abeni <pabeni@redhat.com>:

On Tue, 11 Jun 2024 10:35:58 +0200 you wrote:
> STM32MP13 is STM32 SOC with 2 GMACs instances
>     GMAC IP version is SNPS 4.20.
>     GMAC IP configure with 1 RX and 1 TX queue.
>     DMA HW capability register supported
>     RX Checksum Offload Engine supported
>     TX Checksum insertion supported
>     Wake-Up On Lan supported
>     TSO supported
> Rework dwmac glue to simplify management for next stm32 (integrate RFC from Marek)
> 
> [...]

Here is the summary with links:
  - [net-next,v7,1/8] dt-bindings: net: add STM32MP13 compatible in documentation for stm32
    https://git.kernel.org/netdev/net-next/c/8a9044e5169b
  - [net-next,v7,2/8] net: stmmac: dwmac-stm32: Separate out external clock rate validation
    https://git.kernel.org/netdev/net-next/c/582ac134963e
  - [net-next,v7,3/8] net: stmmac: dwmac-stm32: Separate out external clock selector
    https://git.kernel.org/netdev/net-next/c/63b0aa8ea73f
  - [net-next,v7,4/8] net: stmmac: dwmac-stm32: Extract PMCR configuration
    https://git.kernel.org/netdev/net-next/c/92704f8c0e7a
  - [net-next,v7,5/8] net: stmmac: dwmac-stm32: Clean up the debug prints
    https://git.kernel.org/netdev/net-next/c/c60a54b52026
  - [net-next,v7,6/8] net: stmmac: dwmac-stm32: Fix Mhz to MHz
    https://git.kernel.org/netdev/net-next/c/cbfad55322ce
  - [net-next,v7,7/8] net: stmmac: dwmac-stm32: Mask support for PMCR configuration
    https://git.kernel.org/netdev/net-next/c/4f37dc467ffe
  - [net-next,v7,8/8] net: stmmac: dwmac-stm32: add management of stm32mp13 for stm32
    https://git.kernel.org/netdev/net-next/c/50bbc0393114

You are awesome, thank you!
-- 
Deet-doot-dot, I am a bot.
https://korg.docs.kernel.org/patchwork/pwbot.html

Re: [net-next,PATCH v7 2/8] net: stmmac: dwmac-stm32: Separate out external clock rate validation

[Mark Brown]

[-- Attachment #1: Type: text/plain, Size: 3893 bytes --]

On Tue, Jun 11, 2024 at 10:36:00AM +0200, Christophe Roullier wrote:
> From: Marek Vasut <marex@denx.de>
> 
> Pull the external clock frequency validation into a separate function,
> to avoid conflating it with external clock DT property decoding and
> clock mux register configuration. This should make the code easier to
> read and understand.

For the past few days networking has been broken on the Avenger 96, a
stm32mp157a based platform.  The stm32-dwmac driver fails to probe:

<6>[    1.894271] stm32-dwmac 5800a000.ethernet: IRQ eth_wake_irq not found
<6>[    1.899694] stm32-dwmac 5800a000.ethernet: IRQ eth_lpi not found
<6>[    1.905849] stm32-dwmac 5800a000.ethernet: IRQ sfty not found
<3>[    1.912304] stm32-dwmac 5800a000.ethernet: Unable to parse OF data
<3>[    1.918393] stm32-dwmac 5800a000.ethernet: probe with driver stm32-dwmac failed with error -75

which looks a bit odd given the commit contents but I didn't look at the
driver code at all.

Full boot log here:

   https://lava.sirena.org.uk/scheduler/job/467150

A working equivalent is here:

   https://lava.sirena.org.uk/scheduler/job/466518

A bisection identified this commit as being responsible, log below:

git bisect start
# status: waiting for both good and bad commits
# bad: [0fc4bfab2cd45f9acb86c4f04b5191e114e901ed] Add linux-next specific files for 20240625
git bisect bad 0fc4bfab2cd45f9acb86c4f04b5191e114e901ed
# status: waiting for good commit(s), bad commit known
# good: [3d9217c41c07b72af3a5c147cb82c75f757f4200] Merge branch 'for-linux-next-fixes' of https://gitlab.freedesktop.org/drm/misc/kernel.git
git bisect good 3d9217c41c07b72af3a5c147cb82c75f757f4200
# bad: [5699faecf4e2347f81eea62db0455feb4d794537] Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/cryptodev-2.6.git
git bisect bad 5699faecf4e2347f81eea62db0455feb4d794537
# good: [ba73da675606373565868962ad8c615f175662ed] Merge branch 'fs-next' of linux-next
git bisect good ba73da675606373565868962ad8c615f175662ed
# bad: [7e7c714a36a5b10e391168e7e8145060e041ea12] Merge branch 'af_unix-remove-spin_lock_nested-and-convert-to-lock_cmp_fn'
git bisect bad 7e7c714a36a5b10e391168e7e8145060e041ea12
# good: [93d4e8bb3f137e8037a65ea96f175f81c25c50e5] Merge tag 'wireless-next-2024-06-07' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
git bisect good 93d4e8bb3f137e8037a65ea96f175f81c25c50e5
# bad: [4314175af49668ab20c0d60d7d7657986e1d0c7c] Merge branch 'net-smc-IPPROTO_SMC'
git bisect bad 4314175af49668ab20c0d60d7d7657986e1d0c7c
# good: [811efc06e5f30a57030451b2d1998aa81273baf8] net/tcp: Move tcp_inbound_hash() from headers
git bisect good 811efc06e5f30a57030451b2d1998aa81273baf8
# good: [5f703ce5c981ee02c00e210d5b155bbbfbf11263] net: hsr: Send supervisory frames to HSR network with ProxyNodeTable data
git bisect good 5f703ce5c981ee02c00e210d5b155bbbfbf11263
# bad: [6c3282a6b296385bee2c383442c39f507b0d51dd] net: stmmac: add select_pcs() platform method
git bisect bad 6c3282a6b296385bee2c383442c39f507b0d51dd
# bad: [404dbd26322f50c8123bf5bff9a409356889035f] net: qrtr: ns: Ignore ENODEV failures in ns
git bisect bad 404dbd26322f50c8123bf5bff9a409356889035f
# bad: [c60a54b52026bd2c9a88ae00f2aac7a67fed8e38] net: stmmac: dwmac-stm32: Clean up the debug prints
git bisect bad c60a54b52026bd2c9a88ae00f2aac7a67fed8e38
# bad: [582ac134963e2d5cf6c45db027e156fcfb7f7678] net: stmmac: dwmac-stm32: Separate out external clock rate validation
git bisect bad 582ac134963e2d5cf6c45db027e156fcfb7f7678
# good: [8a9044e5169bab7a8edadb4ceb748391657f0d7f] dt-bindings: net: add STM32MP13 compatible in documentation for stm32
git bisect good 8a9044e5169bab7a8edadb4ceb748391657f0d7f
# first bad commit: [582ac134963e2d5cf6c45db027e156fcfb7f7678] net: stmmac: dwmac-stm32: Separate out external clock rate validation

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 488 bytes --]

Re: [net-next,PATCH v7 2/8] net: stmmac: dwmac-stm32: Separate out external clock rate validation

[Christophe ROULLIER]

Hi Mark,

Sorry, issue found, I will push fix this morning.

Regards.

Christophe.

On 6/26/24 12:38, Mark Brown wrote:
> On Tue, Jun 11, 2024 at 10:36:00AM +0200, Christophe Roullier wrote:
>> From: Marek Vasut <marex@denx.de>
>>
>> Pull the external clock frequency validation into a separate function,
>> to avoid conflating it with external clock DT property decoding and
>> clock mux register configuration. This should make the code easier to
>> read and understand.
> For the past few days networking has been broken on the Avenger 96, a
> stm32mp157a based platform.  The stm32-dwmac driver fails to probe:
>
> <6>[    1.894271] stm32-dwmac 5800a000.ethernet: IRQ eth_wake_irq not found
> <6>[    1.899694] stm32-dwmac 5800a000.ethernet: IRQ eth_lpi not found
> <6>[    1.905849] stm32-dwmac 5800a000.ethernet: IRQ sfty not found
> <3>[    1.912304] stm32-dwmac 5800a000.ethernet: Unable to parse OF data
> <3>[    1.918393] stm32-dwmac 5800a000.ethernet: probe with driver stm32-dwmac failed with error -75
>
> which looks a bit odd given the commit contents but I didn't look at the
> driver code at all.
>
> Full boot log here:
>
>     https://lava.sirena.org.uk/scheduler/job/467150
>
> A working equivalent is here:
>
>     https://lava.sirena.org.uk/scheduler/job/466518
>
> A bisection identified this commit as being responsible, log below:
>
> git bisect start
> # status: waiting for both good and bad commits
> # bad: [0fc4bfab2cd45f9acb86c4f04b5191e114e901ed] Add linux-next specific files for 20240625
> git bisect bad 0fc4bfab2cd45f9acb86c4f04b5191e114e901ed
> # status: waiting for good commit(s), bad commit known
> # good: [3d9217c41c07b72af3a5c147cb82c75f757f4200] Merge branch 'for-linux-next-fixes' of https://gitlab.freedesktop.org/drm/misc/kernel.git
> git bisect good 3d9217c41c07b72af3a5c147cb82c75f757f4200
> # bad: [5699faecf4e2347f81eea62db0455feb4d794537] Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/cryptodev-2.6.git
> git bisect bad 5699faecf4e2347f81eea62db0455feb4d794537
> # good: [ba73da675606373565868962ad8c615f175662ed] Merge branch 'fs-next' of linux-next
> git bisect good ba73da675606373565868962ad8c615f175662ed
> # bad: [7e7c714a36a5b10e391168e7e8145060e041ea12] Merge branch 'af_unix-remove-spin_lock_nested-and-convert-to-lock_cmp_fn'
> git bisect bad 7e7c714a36a5b10e391168e7e8145060e041ea12
> # good: [93d4e8bb3f137e8037a65ea96f175f81c25c50e5] Merge tag 'wireless-next-2024-06-07' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
> git bisect good 93d4e8bb3f137e8037a65ea96f175f81c25c50e5
> # bad: [4314175af49668ab20c0d60d7d7657986e1d0c7c] Merge branch 'net-smc-IPPROTO_SMC'
> git bisect bad 4314175af49668ab20c0d60d7d7657986e1d0c7c
> # good: [811efc06e5f30a57030451b2d1998aa81273baf8] net/tcp: Move tcp_inbound_hash() from headers
> git bisect good 811efc06e5f30a57030451b2d1998aa81273baf8
> # good: [5f703ce5c981ee02c00e210d5b155bbbfbf11263] net: hsr: Send supervisory frames to HSR network with ProxyNodeTable data
> git bisect good 5f703ce5c981ee02c00e210d5b155bbbfbf11263
> # bad: [6c3282a6b296385bee2c383442c39f507b0d51dd] net: stmmac: add select_pcs() platform method
> git bisect bad 6c3282a6b296385bee2c383442c39f507b0d51dd
> # bad: [404dbd26322f50c8123bf5bff9a409356889035f] net: qrtr: ns: Ignore ENODEV failures in ns
> git bisect bad 404dbd26322f50c8123bf5bff9a409356889035f
> # bad: [c60a54b52026bd2c9a88ae00f2aac7a67fed8e38] net: stmmac: dwmac-stm32: Clean up the debug prints
> git bisect bad c60a54b52026bd2c9a88ae00f2aac7a67fed8e38
> # bad: [582ac134963e2d5cf6c45db027e156fcfb7f7678] net: stmmac: dwmac-stm32: Separate out external clock rate validation
> git bisect bad 582ac134963e2d5cf6c45db027e156fcfb7f7678
> # good: [8a9044e5169bab7a8edadb4ceb748391657f0d7f] dt-bindings: net: add STM32MP13 compatible in documentation for stm32
> git bisect good 8a9044e5169bab7a8edadb4ceb748391657f0d7f
> # first bad commit: [582ac134963e2d5cf6c45db027e156fcfb7f7678] net: stmmac: dwmac-stm32: Separate out external clock rate validation