From: Minda Chen <minda.chen@starfivetech.com>
To: Conor Dooley <conor@kernel.org>, Rob Herring <robh+dt@kernel.org>,
Emil Renner Berthing <emil.renner.berthing@canonical.com>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
Cc: devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
linux-riscv@lists.infradead.org,
Paul Walmsley <paul.walmsley@sifive.com>,
Palmer Dabbelt <palmer@dabbelt.com>,
Albert Ou <aou@eecs.berkeley.edu>,
Minda Chen <minda.chen@starfivetech.com>
Subject: [PATCH v2 1/1] riscv: dts: starfive: add PCIe dts configuration for JH7110
Date: Fri, 21 Jun 2024 16:22:31 +0800 [thread overview]
Message-ID: <20240621082231.92896-2-minda.chen@starfivetech.com> (raw)
In-Reply-To: <20240621082231.92896-1-minda.chen@starfivetech.com>
Add PCIe dts configuraion for JH7110 SoC platform.
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Reviewed-by: Hal Feng <hal.feng@starfivetech.com>
---
.../boot/dts/starfive/jh7110-common.dtsi | 62 +++++++++++++
.../boot/dts/starfive/jh7110-milkv-mars.dts | 7 ++
.../jh7110-starfive-visionfive-2.dtsi | 8 ++
arch/riscv/boot/dts/starfive/jh7110.dtsi | 86 +++++++++++++++++++
4 files changed, 163 insertions(+)
diff --git a/arch/riscv/boot/dts/starfive/jh7110-common.dtsi b/arch/riscv/boot/dts/starfive/jh7110-common.dtsi
index 8ff6ea64f048..f91abc660ae8 100644
--- a/arch/riscv/boot/dts/starfive/jh7110-common.dtsi
+++ b/arch/riscv/boot/dts/starfive/jh7110-common.dtsi
@@ -294,6 +294,20 @@
status = "okay";
};
+&pcie0 {
+ perst-gpios = <&sysgpio 26 GPIO_ACTIVE_LOW>;
+ phys = <&pciephy0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie0_pins>;
+};
+
+&pcie1 {
+ perst-gpios = <&sysgpio 28 GPIO_ACTIVE_LOW>;
+ phys = <&pciephy1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie1_pins>;
+};
+
&pwmdac {
pinctrl-names = "default";
pinctrl-0 = <&pwmdac_pins>;
@@ -476,6 +490,54 @@
};
};
+ pcie0_pins: pcie0-0 {
+ clkreq-pins {
+ pinmux = <GPIOMUX(27, GPOUT_LOW,
+ GPOEN_DISABLE,
+ GPI_NONE)>;
+ bias-pull-down;
+ drive-strength = <2>;
+ input-enable;
+ input-schmitt-disable;
+ slew-rate = <0>;
+ };
+
+ wake-pins {
+ pinmux = <GPIOMUX(32, GPOUT_LOW,
+ GPOEN_DISABLE,
+ GPI_NONE)>;
+ bias-pull-up;
+ drive-strength = <2>;
+ input-enable;
+ input-schmitt-disable;
+ slew-rate = <0>;
+ };
+ };
+
+ pcie1_pins: pcie1-0 {
+ clkreq-pins {
+ pinmux = <GPIOMUX(29, GPOUT_LOW,
+ GPOEN_DISABLE,
+ GPI_NONE)>;
+ bias-pull-down;
+ drive-strength = <2>;
+ input-enable;
+ input-schmitt-disable;
+ slew-rate = <0>;
+ };
+
+ wake-pins {
+ pinmux = <GPIOMUX(21, GPOUT_LOW,
+ GPOEN_DISABLE,
+ GPI_NONE)>;
+ bias-pull-up;
+ drive-strength = <2>;
+ input-enable;
+ input-schmitt-disable;
+ slew-rate = <0>;
+ };
+ };
+
pwmdac_pins: pwmdac-0 {
pwmdac-pins {
pinmux = <GPIOMUX(33, GPOUT_SYS_PWMDAC_LEFT,
diff --git a/arch/riscv/boot/dts/starfive/jh7110-milkv-mars.dts b/arch/riscv/boot/dts/starfive/jh7110-milkv-mars.dts
index fa0eac78e0ba..5cb9e99e1dac 100644
--- a/arch/riscv/boot/dts/starfive/jh7110-milkv-mars.dts
+++ b/arch/riscv/boot/dts/starfive/jh7110-milkv-mars.dts
@@ -17,6 +17,13 @@
assigned-clock-parents = <&aoncrg JH7110_AONCLK_GMAC0_RMII_RTX>;
};
+&pcie0 {
+ status = "okay";
+};
+
+&pcie1 {
+ status = "okay";
+};
&phy0 {
motorcomm,tx-clk-adj-enabled;
diff --git a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
index 9d70f21c86fc..18f38fc790a4 100644
--- a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
+++ b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
@@ -32,3 +32,11 @@
&mmc0 {
non-removable;
};
+
+&pcie0 {
+ status = "okay";
+};
+
+&pcie1 {
+ status = "okay";
+};
diff --git a/arch/riscv/boot/dts/starfive/jh7110.dtsi b/arch/riscv/boot/dts/starfive/jh7110.dtsi
index 18047195c600..5ac70759e0ab 100644
--- a/arch/riscv/boot/dts/starfive/jh7110.dtsi
+++ b/arch/riscv/boot/dts/starfive/jh7110.dtsi
@@ -1214,5 +1214,91 @@
#reset-cells = <1>;
power-domains = <&pwrc JH7110_PD_VOUT>;
};
+
+ pcie0: pcie@940000000 {
+ compatible = "starfive,jh7110-pcie";
+ reg = <0x9 0x40000000 0x0 0x1000000>,
+ <0x0 0x2b000000 0x0 0x100000>;
+ reg-names = "cfg", "apb";
+ linux,pci-domain = <0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges = <0x82000000 0x0 0x30000000 0x0 0x30000000 0x0 0x08000000>,
+ <0xc3000000 0x9 0x00000000 0x9 0x00000000 0x0 0x40000000>;
+ interrupts = <56>;
+ interrupt-map-mask = <0x0 0x0 0x0 0x7>;
+ interrupt-map = <0x0 0x0 0x0 0x1 &pcie_intc0 0x1>,
+ <0x0 0x0 0x0 0x2 &pcie_intc0 0x2>,
+ <0x0 0x0 0x0 0x3 &pcie_intc0 0x3>,
+ <0x0 0x0 0x0 0x4 &pcie_intc0 0x4>;
+ msi-controller;
+ device_type = "pci";
+ starfive,stg-syscon = <&stg_syscon>;
+ bus-range = <0x0 0xff>;
+ clocks = <&syscrg JH7110_SYSCLK_NOC_BUS_STG_AXI>,
+ <&stgcrg JH7110_STGCLK_PCIE0_TL>,
+ <&stgcrg JH7110_STGCLK_PCIE0_AXI_MST0>,
+ <&stgcrg JH7110_STGCLK_PCIE0_APB>;
+ clock-names = "noc", "tl", "axi_mst0", "apb";
+ resets = <&stgcrg JH7110_STGRST_PCIE0_AXI_MST0>,
+ <&stgcrg JH7110_STGRST_PCIE0_AXI_SLV0>,
+ <&stgcrg JH7110_STGRST_PCIE0_AXI_SLV>,
+ <&stgcrg JH7110_STGRST_PCIE0_BRG>,
+ <&stgcrg JH7110_STGRST_PCIE0_CORE>,
+ <&stgcrg JH7110_STGRST_PCIE0_APB>;
+ reset-names = "mst0", "slv0", "slv", "brg",
+ "core", "apb";
+ status = "disabled";
+
+ pcie_intc0: interrupt-controller {
+ #address-cells = <0>;
+ #interrupt-cells = <1>;
+ interrupt-controller;
+ };
+ };
+
+ pcie1: pcie@9c0000000 {
+ compatible = "starfive,jh7110-pcie";
+ reg = <0x9 0xc0000000 0x0 0x1000000>,
+ <0x0 0x2c000000 0x0 0x100000>;
+ reg-names = "cfg", "apb";
+ linux,pci-domain = <1>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges = <0x82000000 0x0 0x38000000 0x0 0x38000000 0x0 0x08000000>,
+ <0xc3000000 0x9 0x80000000 0x9 0x80000000 0x0 0x40000000>;
+ interrupts = <57>;
+ interrupt-map-mask = <0x0 0x0 0x0 0x7>;
+ interrupt-map = <0x0 0x0 0x0 0x1 &pcie_intc1 0x1>,
+ <0x0 0x0 0x0 0x2 &pcie_intc1 0x2>,
+ <0x0 0x0 0x0 0x3 &pcie_intc1 0x3>,
+ <0x0 0x0 0x0 0x4 &pcie_intc1 0x4>;
+ msi-controller;
+ device_type = "pci";
+ starfive,stg-syscon = <&stg_syscon>;
+ bus-range = <0x0 0xff>;
+ clocks = <&syscrg JH7110_SYSCLK_NOC_BUS_STG_AXI>,
+ <&stgcrg JH7110_STGCLK_PCIE1_TL>,
+ <&stgcrg JH7110_STGCLK_PCIE1_AXI_MST0>,
+ <&stgcrg JH7110_STGCLK_PCIE1_APB>;
+ clock-names = "noc", "tl", "axi_mst0", "apb";
+ resets = <&stgcrg JH7110_STGRST_PCIE1_AXI_MST0>,
+ <&stgcrg JH7110_STGRST_PCIE1_AXI_SLV0>,
+ <&stgcrg JH7110_STGRST_PCIE1_AXI_SLV>,
+ <&stgcrg JH7110_STGRST_PCIE1_BRG>,
+ <&stgcrg JH7110_STGRST_PCIE1_CORE>,
+ <&stgcrg JH7110_STGRST_PCIE1_APB>;
+ reset-names = "mst0", "slv0", "slv", "brg",
+ "core", "apb";
+ status = "disabled";
+
+ pcie_intc1: interrupt-controller {
+ #address-cells = <0>;
+ #interrupt-cells = <1>;
+ interrupt-controller;
+ };
+ };
};
};
--
2.17.1
next prev parent reply other threads:[~2024-06-21 8:38 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-06-21 8:22 [PATCH v2 0/1] Add PCIe dts configuration for JH7110 Minda Chen
2024-06-21 8:22 ` Minda Chen [this message]
2024-06-22 12:08 ` [PATCH v2 1/1] riscv: dts: starfive: add " Conor Dooley
2024-06-24 1:18 ` Minda Chen
2024-06-24 16:32 ` Conor Dooley
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20240621082231.92896-2-minda.chen@starfivetech.com \
--to=minda.chen@starfivetech.com \
--cc=aou@eecs.berkeley.edu \
--cc=conor@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=emil.renner.berthing@canonical.com \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-riscv@lists.infradead.org \
--cc=palmer@dabbelt.com \
--cc=paul.walmsley@sifive.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).