[PATCH v3 4/8] ASoC: msm8916-wcd-analog: add pm8953 codec

[Adam Skladowski <a39.skl@gmail.com>]

From: Vladimir Lypak <vladimir.lypak@gmail.com>

Add regs overrides for PM8953 codec.

Signed-off-by: Vladimir Lypak <vladimir.lypak@gmail.com>
[Adam: rename codec]
Signed-off-by: Adam Skladowski <a39.skl@gmail.com>
---
 sound/soc/codecs/msm8916-wcd-analog.c | 29 +++++++++++++++++++++++++++++
 1 file changed, 29 insertions(+)

diff --git a/sound/soc/codecs/msm8916-wcd-analog.c b/sound/soc/codecs/msm8916-wcd-analog.c
index 13df60409857..b9325290c28d 100644
--- a/sound/soc/codecs/msm8916-wcd-analog.c
+++ b/sound/soc/codecs/msm8916-wcd-analog.c
@@ -755,6 +755,34 @@ static const struct wcd_reg_seq pm8950_data = {
 	.seq_size = ARRAY_SIZE(wcd_reg_defaults_pm8950),
 };
 
+static const struct reg_default wcd_reg_defaults_pm8953[] = {
+	{CDC_A_RX_COM_OCP_CTL, 0xd1},
+	{CDC_A_RX_COM_OCP_COUNT, 0xff},
+	{CDC_D_SEC_ACCESS, 0xa5},
+	{CDC_D_PERPH_RESET_CTL3, 0x0f},
+	{CDC_A_TX_1_2_OPAMP_BIAS, 0x4c},
+	{CDC_A_NCP_FBCTRL, 0xa8},
+	{CDC_A_NCP_VCTRL, 0xa4},
+	{CDC_A_SPKR_DRV_CTL, 0x69},
+	{CDC_A_SPKR_DRV_DBG, 0x01},
+	{CDC_A_SEC_ACCESS, 0xa5},
+	{CDC_A_PERPH_RESET_CTL3, 0x0f},
+	{CDC_A_CURRENT_LIMIT, 0xa2},
+	{CDC_A_BYPASS_MODE, 0x18},
+	{CDC_A_SPKR_ANA_BIAS_SET, 0x41},
+	{CDC_A_SPKR_DAC_CTL, 0x03},
+	{CDC_A_SPKR_OCP_CTL, 0xe1},
+	{CDC_A_RX_HPH_BIAS_PA, 0xfa},
+	{CDC_A_RX_EAR_STATUS, 0x10},
+	{CDC_A_MASTER_BIAS_CTL, 0x30},
+	{CDC_A_MICB_1_INT_RBIAS, 0x00},
+};
+
+static const struct wcd_reg_seq pm8953_data = {
+	.seq = wcd_reg_defaults_pm8953,
+	.seq_size = ARRAY_SIZE(wcd_reg_defaults_pm8953),
+};
+
 static int pm8916_wcd_analog_probe(struct snd_soc_component *component)
 {
 	struct pm8916_wcd_analog_priv *priv = dev_get_drvdata(component->dev);
@@ -1304,6 +1332,7 @@ static int pm8916_wcd_analog_spmi_probe(struct platform_device *pdev)
 static const struct of_device_id pm8916_wcd_analog_spmi_match_table[] = {
 	{ .compatible = "qcom,pm8916-wcd-analog-codec", .data = &pm8916_data },
 	{ .compatible = "qcom,pm8950-wcd-analog-codec", .data = &pm8950_data },
+	{ .compatible = "qcom,pm8953-wcd-analog-codec", .data = &pm8953_data },
 	{ }
 };
 

-- 
2.45.2