[PATCH] arm64: dts: imx8mm: Update Data Modul i.MX8M Mini eDM SBC DT to rev.A01

[Marek Vasut <marex@denx.de>]

Update the DT to match newest Data Modul i.MX8M Mini eDM SBC rev.A01
board which implements PHY changes. Keep some of the rev.900 PHY node
in the DT so that a DTO can be used to support rev.900 boards easily.

Signed-off-by: Marek Vasut <marex@denx.de>
---
Cc: Conor Dooley <conor+dt@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Krzysztof Kozlowski <krzk+dt@kernel.org>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Rob Herring <robh@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: devicetree@vger.kernel.org
Cc: imx@lists.linux.dev
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
---
 .../freescale/imx8mm-data-modul-edm-sbc.dts   | 19 +++++++++++++++++--
 1 file changed, 17 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-data-modul-edm-sbc.dts b/arch/arm64/boot/dts/freescale/imx8mm-data-modul-edm-sbc.dts
index b1f2beb40a98f..472c584fb3bd2 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-data-modul-edm-sbc.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-data-modul-edm-sbc.dts
@@ -168,7 +168,7 @@ &fec1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_fec1>;
 	phy-mode = "rgmii-id";
-	phy-handle = <&fec1_phy>;
+	phy-handle = <&fec1_phy_bcm>;
 	phy-supply = <&buck4_reg>;
 	fsl,magic-packet;
 	status = "okay";
@@ -178,7 +178,7 @@ mdio {
 		#size-cells = <0>;
 
 		/* Atheros AR8031 PHY */
-		fec1_phy: ethernet-phy@0 {
+		fec1_phy_ath: ethernet-phy@0 {
 			compatible = "ethernet-phy-ieee802.3-c22";
 			reg = <0>;
 			/*
@@ -191,6 +191,7 @@ fec1_phy: ethernet-phy@0 {
 			reset-deassert-us = <10000>;
 			qca,keep-pll-enabled;
 			vddio-supply = <&vddio>;
+			status = "disabled";
 
 			vddio: vddio-regulator {
 				regulator-name = "VDDIO";
@@ -202,6 +203,20 @@ vddh: vddh-regulator {
 				regulator-name = "VDDH";
 			};
 		};
+
+		/* Broadcom BCM54213PE PHY */
+		fec1_phy_bcm: ethernet-phy@1 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <1>;
+			/*
+			 * Dedicated ENET_INT# and ENET_WOL# signals are
+			 * unused, the PHY does not provide cable detect
+			 * interrupt.
+			 */
+			reset-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <10000>;
+		};
 	};
 };
 
-- 
2.43.0