[PATCH V3 00/15] Add Battery and USB Supply for AXP717

[PATCH V3 00/15] Add Battery and USB Supply for AXP717

[Chris Morgan]

From: Chris Morgan <macromorgan@hotmail.com>

Add support for monitoring the USB charger and battery charger on the
AXP717 PMIC. This required some driver refactoring of the axp20x USB
and battery charger as the AXP717 is somewhat different but can still
benefit from some common elements.

Note that as of now the charging current now value may be incorrect as
the scale and offsets were not documented in the datasheet. I suspect
the scale is 1 and the offset is somewhere around 450mA though.

Changes from V2:
 - Added constraints for input-current-limit-microamp constraints for
   x-powers,axp20x-usb-power-supply.yaml.
 - Used FIELD_GET() and removed unnecessary -EINVAL per comments from
   Jonathan Cameron.

Changes from V1:
 - Refactored against mainline to remove BOOST pre-requisite.
 - Corrected commit subjects for DT bindings.
 - Split refactoring and AXP717 support into different patches.
 - Added IRQ for VBUS over voltage. There appears to be a bug
   with the VBUS fault IRQ because it is assigned IRQ num 0.
 - Corrected battery driver to report POWER_SUPPLY_PROP_VOLTAGE_MIN
   and POWER_SUPPLY_PROP_VOLTAGE_MAX instead of *_DESIGN.

Chris Morgan (15):
  iio: adc: axp20x_adc: Add adc_en1 and adc_en1 to axp_data
  power: supply: axp20x_battery: Remove design from min and max voltage
  power: supply: axp20x_battery: Make iio and battery config per device
  power: supply: axp20x_usb_power: Make VBUS and IIO config per device
  dt-bindings: power: supply: axp20x: Add input-current-limit-microamp
  power: supply: axp20x_usb_power: add input-current-limit-microamp
  dt-bindings: power: supply: axp20x-battery: Add monitored-battery
  dt-bindings: iio: adc: Add AXP717 compatible
  dt-bindings: power: supply: axp20x: Add AXP717 compatible
  dt-bindings: power: supply: axp20x: Add AXP717 compatible
  mfd: axp20x: Add ADC, BAT, and USB cells for AXP717
  iio: adc: axp20x_adc: add support for AXP717 ADC
  power: supply: axp20x_usb_power: Add support for AXP717
  power: supply: axp20x_battery: add support for AXP717
  arm64: dts: allwinner: h700: Add charger for Anbernic RG35XX

 .../bindings/iio/adc/x-powers,axp209-adc.yaml |  12 +
 .../x-powers,axp20x-battery-power-supply.yaml |   7 +
 .../x-powers,axp20x-usb-power-supply.yaml     |  70 ++-
 .../sun50i-h700-anbernic-rg35xx-2024.dts      |  21 +
 drivers/iio/adc/axp20x_adc.c                  | 182 +++++-
 drivers/mfd/axp20x.c                          |  25 +-
 drivers/power/supply/axp20x_battery.c         | 590 ++++++++++++++++--
 drivers/power/supply/axp20x_usb_power.c       | 353 ++++++++++-
 include/linux/mfd/axp20x.h                    |  27 +
 9 files changed, 1186 insertions(+), 101 deletions(-)

-- 
2.34.1

[PATCH V3 01/15] iio: adc: axp20x_adc: Add adc_en1 and adc_en1 to axp_data

[Chris Morgan]

From: Chris Morgan <macromorgan@hotmail.com>

Add the register for adc_en1 and adc_en2 to the axp_data struct. This
allows us to specify a different register to enable the adc channels
for different devices such as the AXP717.

Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
---
 drivers/iio/adc/axp20x_adc.c | 22 +++++++++++++++-------
 1 file changed, 15 insertions(+), 7 deletions(-)

diff --git a/drivers/iio/adc/axp20x_adc.c b/drivers/iio/adc/axp20x_adc.c
index b487e577befb..368ba6ee7a80 100644
--- a/drivers/iio/adc/axp20x_adc.c
+++ b/drivers/iio/adc/axp20x_adc.c
@@ -889,7 +889,9 @@ struct axp_data {
 	const struct iio_info		*iio_info;
 	int				num_channels;
 	struct iio_chan_spec const	*channels;
+	unsigned long			adc_en1;
 	unsigned long			adc_en1_mask;
+	unsigned long			adc_en2;
 	unsigned long			adc_en2_mask;
 	int				(*adc_rate)(struct axp20x_adc_iio *info,
 						    int rate);
@@ -910,7 +912,9 @@ static const struct axp_data axp20x_data = {
 	.iio_info = &axp20x_adc_iio_info,
 	.num_channels = ARRAY_SIZE(axp20x_adc_channels),
 	.channels = axp20x_adc_channels,
+	.adc_en1 = AXP20X_ADC_EN1,
 	.adc_en1_mask = AXP20X_ADC_EN1_MASK,
+	.adc_en2 = AXP20X_ADC_EN2,
 	.adc_en2_mask = AXP20X_ADC_EN2_MASK,
 	.adc_rate = axp20x_adc_rate,
 	.maps = axp20x_maps,
@@ -920,6 +924,7 @@ static const struct axp_data axp22x_data = {
 	.iio_info = &axp22x_adc_iio_info,
 	.num_channels = ARRAY_SIZE(axp22x_adc_channels),
 	.channels = axp22x_adc_channels,
+	.adc_en1 = AXP20X_ADC_EN1,
 	.adc_en1_mask = AXP22X_ADC_EN1_MASK,
 	.adc_rate = axp22x_adc_rate,
 	.maps = axp22x_maps,
@@ -929,6 +934,7 @@ static const struct axp_data axp813_data = {
 	.iio_info = &axp813_adc_iio_info,
 	.num_channels = ARRAY_SIZE(axp813_adc_channels),
 	.channels = axp813_adc_channels,
+	.adc_en1 = AXP20X_ADC_EN1,
 	.adc_en1_mask = AXP22X_ADC_EN1_MASK,
 	.adc_rate = axp813_adc_rate,
 	.maps = axp22x_maps,
@@ -988,14 +994,16 @@ static int axp20x_probe(struct platform_device *pdev)
 	indio_dev->channels = info->data->channels;
 
 	/* Enable the ADCs on IP */
-	regmap_write(info->regmap, AXP20X_ADC_EN1, info->data->adc_en1_mask);
+	regmap_write(info->regmap, info->data->adc_en1,
+		     info->data->adc_en1_mask);
 
 	if (info->data->adc_en2_mask)
-		regmap_set_bits(info->regmap, AXP20X_ADC_EN2,
+		regmap_set_bits(info->regmap, info->data->adc_en2,
 				info->data->adc_en2_mask);
 
 	/* Configure ADCs rate */
-	info->data->adc_rate(info, 100);
+	if (info->data->adc_rate)
+		info->data->adc_rate(info, 100);
 
 	ret = iio_map_array_register(indio_dev, info->data->maps);
 	if (ret < 0) {
@@ -1015,10 +1023,10 @@ static int axp20x_probe(struct platform_device *pdev)
 	iio_map_array_unregister(indio_dev);
 
 fail_map:
-	regmap_write(info->regmap, AXP20X_ADC_EN1, 0);
+	regmap_write(info->regmap, info->data->adc_en1, 0);
 
 	if (info->data->adc_en2_mask)
-		regmap_write(info->regmap, AXP20X_ADC_EN2, 0);
+		regmap_write(info->regmap, info->data->adc_en2, 0);
 
 	return ret;
 }
@@ -1031,10 +1039,10 @@ static void axp20x_remove(struct platform_device *pdev)
 	iio_device_unregister(indio_dev);
 	iio_map_array_unregister(indio_dev);
 
-	regmap_write(info->regmap, AXP20X_ADC_EN1, 0);
+	regmap_write(info->regmap, info->data->adc_en1, 0);
 
 	if (info->data->adc_en2_mask)
-		regmap_write(info->regmap, AXP20X_ADC_EN2, 0);
+		regmap_write(info->regmap, info->data->adc_en2, 0);
 }
 
 static struct platform_driver axp20x_adc_driver = {
-- 
2.34.1

[PATCH V3 02/15] power: supply: axp20x_battery: Remove design from min and max voltage

[Chris Morgan]

From: Chris Morgan <macromorgan@hotmail.com>

The POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN and
POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN values should be immutable
properties of the battery, but for this driver they are writable values
and used as the minimum and maximum values for charging. Remove the
DESIGN designation from these values.

Fixes: 46c202b5f25f ("power: supply: add battery driver for AXP20X and AXP22X PMICs")
Suggested-by: Chen-Yu Tsai <wens@kernel.org>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
---
 drivers/power/supply/axp20x_battery.c | 16 ++++++++--------
 1 file changed, 8 insertions(+), 8 deletions(-)

diff --git a/drivers/power/supply/axp20x_battery.c b/drivers/power/supply/axp20x_battery.c
index 6ac5c80cfda2..7520b599eb3d 100644
--- a/drivers/power/supply/axp20x_battery.c
+++ b/drivers/power/supply/axp20x_battery.c
@@ -303,11 +303,11 @@ static int axp20x_battery_get_prop(struct power_supply *psy,
 		val->intval = reg & AXP209_FG_PERCENT;
 		break;
 
-	case POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN:
+	case POWER_SUPPLY_PROP_VOLTAGE_MAX:
 		return axp20x_batt->data->get_max_voltage(axp20x_batt,
 							  &val->intval);
 
-	case POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN:
+	case POWER_SUPPLY_PROP_VOLTAGE_MIN:
 		ret = regmap_read(axp20x_batt->regmap, AXP20X_V_OFF, &reg);
 		if (ret)
 			return ret;
@@ -455,10 +455,10 @@ static int axp20x_battery_set_prop(struct power_supply *psy,
 	struct axp20x_batt_ps *axp20x_batt = power_supply_get_drvdata(psy);
 
 	switch (psp) {
-	case POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN:
+	case POWER_SUPPLY_PROP_VOLTAGE_MIN:
 		return axp20x_set_voltage_min_design(axp20x_batt, val->intval);
 
-	case POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN:
+	case POWER_SUPPLY_PROP_VOLTAGE_MAX:
 		return axp20x_batt->data->set_max_voltage(axp20x_batt, val->intval);
 
 	case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT:
@@ -493,8 +493,8 @@ static enum power_supply_property axp20x_battery_props[] = {
 	POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT,
 	POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX,
 	POWER_SUPPLY_PROP_HEALTH,
-	POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN,
-	POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN,
+	POWER_SUPPLY_PROP_VOLTAGE_MAX,
+	POWER_SUPPLY_PROP_VOLTAGE_MIN,
 	POWER_SUPPLY_PROP_CAPACITY,
 };
 
@@ -502,8 +502,8 @@ static int axp20x_battery_prop_writeable(struct power_supply *psy,
 					 enum power_supply_property psp)
 {
 	return psp == POWER_SUPPLY_PROP_STATUS ||
-	       psp == POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN ||
-	       psp == POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN ||
+	       psp == POWER_SUPPLY_PROP_VOLTAGE_MIN ||
+	       psp == POWER_SUPPLY_PROP_VOLTAGE_MAX ||
 	       psp == POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT ||
 	       psp == POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX;
 }
-- 
2.34.1

[PATCH V3 03/15] power: supply: axp20x_battery: Make iio and battery config per device

[Chris Morgan]

From: Chris Morgan <macromorgan@hotmail.com>

Move the configuration of battery specific information and available
iio channels from the probe function to a device specific routine,
allowing us to use this driver for devices with slightly different
configurations (such as the AXP717).

Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
---
 drivers/power/supply/axp20x_battery.c | 137 +++++++++++++++++---------
 1 file changed, 88 insertions(+), 49 deletions(-)

diff --git a/drivers/power/supply/axp20x_battery.c b/drivers/power/supply/axp20x_battery.c
index 7520b599eb3d..c903c588b361 100644
--- a/drivers/power/supply/axp20x_battery.c
+++ b/drivers/power/supply/axp20x_battery.c
@@ -58,11 +58,19 @@
 struct axp20x_batt_ps;
 
 struct axp_data {
-	int	ccc_scale;
-	int	ccc_offset;
-	bool	has_fg_valid;
+	int		ccc_scale;
+	int		ccc_offset;
+	unsigned int	ccc_reg;
+	unsigned int	ccc_mask;
+	bool		has_fg_valid;
+	const struct	power_supply_desc *bat_ps_desc;
 	int	(*get_max_voltage)(struct axp20x_batt_ps *batt, int *val);
 	int	(*set_max_voltage)(struct axp20x_batt_ps *batt, int val);
+	int	(*cfg_iio_chan)(struct platform_device *pdev,
+				struct axp20x_batt_ps *axp_batt);
+	void	(*set_bat_info)(struct platform_device *pdev,
+				struct axp20x_batt_ps *axp_batt,
+				struct power_supply_battery_info *info);
 };
 
 struct axp20x_batt_ps {
@@ -508,7 +516,7 @@ static int axp20x_battery_prop_writeable(struct power_supply *psy,
 	       psp == POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX;
 }
 
-static const struct power_supply_desc axp20x_batt_ps_desc = {
+static const struct power_supply_desc axp209_batt_ps_desc = {
 	.name = "axp20x-battery",
 	.type = POWER_SUPPLY_TYPE_BATTERY,
 	.properties = axp20x_battery_props,
@@ -518,27 +526,94 @@ static const struct power_supply_desc axp20x_batt_ps_desc = {
 	.set_property = axp20x_battery_set_prop,
 };
 
+static int axp209_bat_cfg_iio_channels(struct platform_device *pdev,
+				       struct axp20x_batt_ps *axp_batt)
+{
+	axp_batt->batt_v = devm_iio_channel_get(&pdev->dev, "batt_v");
+	if (IS_ERR(axp_batt->batt_v)) {
+		if (PTR_ERR(axp_batt->batt_v) == -ENODEV)
+			return -EPROBE_DEFER;
+		return PTR_ERR(axp_batt->batt_v);
+	}
+
+	axp_batt->batt_chrg_i = devm_iio_channel_get(&pdev->dev,
+							"batt_chrg_i");
+	if (IS_ERR(axp_batt->batt_chrg_i)) {
+		if (PTR_ERR(axp_batt->batt_chrg_i) == -ENODEV)
+			return -EPROBE_DEFER;
+		return PTR_ERR(axp_batt->batt_chrg_i);
+	}
+
+	axp_batt->batt_dischrg_i = devm_iio_channel_get(&pdev->dev,
+							   "batt_dischrg_i");
+	if (IS_ERR(axp_batt->batt_dischrg_i)) {
+		if (PTR_ERR(axp_batt->batt_dischrg_i) == -ENODEV)
+			return -EPROBE_DEFER;
+		return PTR_ERR(axp_batt->batt_dischrg_i);
+	}
+
+	return 0;
+}
+
+static void axp209_set_battery_info(struct platform_device *pdev,
+				    struct axp20x_batt_ps *axp_batt,
+				    struct power_supply_battery_info *info)
+{
+	int vmin = info->voltage_min_design_uv;
+	int ccc = info->constant_charge_current_max_ua;
+
+	if (vmin > 0 && axp20x_set_voltage_min_design(axp_batt, vmin))
+		dev_err(&pdev->dev,
+			"couldn't set voltage_min_design\n");
+
+	/* Set max to unverified value to be able to set CCC */
+	axp_batt->max_ccc = ccc;
+
+	if (ccc <= 0 || axp20x_set_constant_charge_current(axp_batt, ccc)) {
+		dev_err(&pdev->dev,
+			"couldn't set ccc from DT: fallback to min value\n");
+		ccc = 300000;
+		axp_batt->max_ccc = ccc;
+		axp20x_set_constant_charge_current(axp_batt, ccc);
+	}
+}
+
 static const struct axp_data axp209_data = {
 	.ccc_scale = 100000,
 	.ccc_offset = 300000,
+	.ccc_reg = AXP20X_CHRG_CTRL1,
+	.ccc_mask = AXP20X_CHRG_CTRL1_TGT_CURR,
+	.bat_ps_desc = &axp209_batt_ps_desc,
 	.get_max_voltage = axp20x_battery_get_max_voltage,
 	.set_max_voltage = axp20x_battery_set_max_voltage,
+	.cfg_iio_chan = axp209_bat_cfg_iio_channels,
+	.set_bat_info = axp209_set_battery_info,
 };
 
 static const struct axp_data axp221_data = {
 	.ccc_scale = 150000,
 	.ccc_offset = 300000,
+	.ccc_reg = AXP20X_CHRG_CTRL1,
+	.ccc_mask = AXP20X_CHRG_CTRL1_TGT_CURR,
 	.has_fg_valid = true,
+	.bat_ps_desc = &axp209_batt_ps_desc,
 	.get_max_voltage = axp22x_battery_get_max_voltage,
 	.set_max_voltage = axp22x_battery_set_max_voltage,
+	.cfg_iio_chan = axp209_bat_cfg_iio_channels,
+	.set_bat_info = axp209_set_battery_info,
 };
 
 static const struct axp_data axp813_data = {
 	.ccc_scale = 200000,
 	.ccc_offset = 200000,
+	.ccc_reg = AXP20X_CHRG_CTRL1,
+	.ccc_mask = AXP20X_CHRG_CTRL1_TGT_CURR,
 	.has_fg_valid = true,
+	.bat_ps_desc = &axp209_batt_ps_desc,
 	.get_max_voltage = axp813_battery_get_max_voltage,
 	.set_max_voltage = axp20x_battery_set_max_voltage,
+	.cfg_iio_chan = axp209_bat_cfg_iio_channels,
+	.set_bat_info = axp209_set_battery_info,
 };
 
 static const struct of_device_id axp20x_battery_ps_id[] = {
@@ -561,6 +636,7 @@ static int axp20x_power_probe(struct platform_device *pdev)
 	struct power_supply_config psy_cfg = {};
 	struct power_supply_battery_info *info;
 	struct device *dev = &pdev->dev;
+	int ret;
 
 	if (!of_device_is_available(pdev->dev.of_node))
 		return -ENODEV;
@@ -572,29 +648,6 @@ static int axp20x_power_probe(struct platform_device *pdev)
 
 	axp20x_batt->dev = &pdev->dev;
 
-	axp20x_batt->batt_v = devm_iio_channel_get(&pdev->dev, "batt_v");
-	if (IS_ERR(axp20x_batt->batt_v)) {
-		if (PTR_ERR(axp20x_batt->batt_v) == -ENODEV)
-			return -EPROBE_DEFER;
-		return PTR_ERR(axp20x_batt->batt_v);
-	}
-
-	axp20x_batt->batt_chrg_i = devm_iio_channel_get(&pdev->dev,
-							"batt_chrg_i");
-	if (IS_ERR(axp20x_batt->batt_chrg_i)) {
-		if (PTR_ERR(axp20x_batt->batt_chrg_i) == -ENODEV)
-			return -EPROBE_DEFER;
-		return PTR_ERR(axp20x_batt->batt_chrg_i);
-	}
-
-	axp20x_batt->batt_dischrg_i = devm_iio_channel_get(&pdev->dev,
-							   "batt_dischrg_i");
-	if (IS_ERR(axp20x_batt->batt_dischrg_i)) {
-		if (PTR_ERR(axp20x_batt->batt_dischrg_i) == -ENODEV)
-			return -EPROBE_DEFER;
-		return PTR_ERR(axp20x_batt->batt_dischrg_i);
-	}
-
 	axp20x_batt->regmap = dev_get_regmap(pdev->dev.parent, NULL);
 	platform_set_drvdata(pdev, axp20x_batt);
 
@@ -603,8 +656,12 @@ static int axp20x_power_probe(struct platform_device *pdev)
 
 	axp20x_batt->data = (struct axp_data *)of_device_get_match_data(dev);
 
+	ret = axp20x_batt->data->cfg_iio_chan(pdev, axp20x_batt);
+	if (ret)
+		return ret;
+
 	axp20x_batt->batt = devm_power_supply_register(&pdev->dev,
-						       &axp20x_batt_ps_desc,
+						       axp20x_batt->data->bat_ps_desc,
 						       &psy_cfg);
 	if (IS_ERR(axp20x_batt->batt)) {
 		dev_err(&pdev->dev, "failed to register power supply: %ld\n",
@@ -613,33 +670,15 @@ static int axp20x_power_probe(struct platform_device *pdev)
 	}
 
 	if (!power_supply_get_battery_info(axp20x_batt->batt, &info)) {
-		int vmin = info->voltage_min_design_uv;
-		int ccc = info->constant_charge_current_max_ua;
-
-		if (vmin > 0 && axp20x_set_voltage_min_design(axp20x_batt,
-							      vmin))
-			dev_err(&pdev->dev,
-				"couldn't set voltage_min_design\n");
-
-		/* Set max to unverified value to be able to set CCC */
-		axp20x_batt->max_ccc = ccc;
-
-		if (ccc <= 0 || axp20x_set_constant_charge_current(axp20x_batt,
-								   ccc)) {
-			dev_err(&pdev->dev,
-				"couldn't set constant charge current from DT: fallback to minimum value\n");
-			ccc = 300000;
-			axp20x_batt->max_ccc = ccc;
-			axp20x_set_constant_charge_current(axp20x_batt, ccc);
-		}
+		axp20x_batt->data->set_bat_info(pdev, axp20x_batt, info);
+		power_supply_put_battery_info(axp20x_batt->batt, info);
 	}
 
 	/*
 	 * Update max CCC to a valid value if battery info is present or set it
 	 * to current register value by default.
 	 */
-	axp20x_get_constant_charge_current(axp20x_batt,
-					   &axp20x_batt->max_ccc);
+	axp20x_get_constant_charge_current(axp20x_batt, &axp20x_batt->max_ccc);
 
 	return 0;
 }
-- 
2.34.1

[PATCH V3 04/15] power: supply: axp20x_usb_power: Make VBUS and IIO config per device

[Chris Morgan]

From: Chris Morgan <macromorgan@hotmail.com>

Make reading of the vbus value and configuring of the iio channels
device specific, to allow additional devices (such as the AXP717) to
be supported by this driver.

Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
---
 drivers/power/supply/axp20x_usb_power.c | 87 +++++++++++++++----------
 1 file changed, 54 insertions(+), 33 deletions(-)

diff --git a/drivers/power/supply/axp20x_usb_power.c b/drivers/power/supply/axp20x_usb_power.c
index dae7e5cfc54e..cd9e92f2ce71 100644
--- a/drivers/power/supply/axp20x_usb_power.c
+++ b/drivers/power/supply/axp20x_usb_power.c
@@ -45,6 +45,8 @@
  */
 #define DEBOUNCE_TIME			msecs_to_jiffies(50)
 
+struct axp20x_usb_power;
+
 struct axp_data {
 	const struct power_supply_desc	*power_desc;
 	const char * const		*irq_names;
@@ -58,6 +60,10 @@ struct axp_data {
 	struct reg_field		usb_bc_det_fld;
 	struct reg_field		vbus_disable_bit;
 	bool				vbus_needs_polling: 1;
+	void (*axp20x_read_vbus)(struct work_struct *work);
+	int (*axp20x_cfg_iio_chan)(struct platform_device *pdev,
+				   struct axp20x_usb_power *power);
+	int (*axp20x_cfg_adc_reg)(struct axp20x_usb_power *power);
 };
 
 struct axp20x_usb_power {
@@ -385,6 +391,36 @@ static int axp20x_usb_power_prop_writeable(struct power_supply *psy,
 	       psp == POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT;
 }
 
+static int axp20x_configure_iio_channels(struct platform_device *pdev,
+					 struct axp20x_usb_power *power)
+{
+	power->vbus_v = devm_iio_channel_get(&pdev->dev, "vbus_v");
+	if (IS_ERR(power->vbus_v)) {
+		if (PTR_ERR(power->vbus_v) == -ENODEV)
+			return -EPROBE_DEFER;
+		return PTR_ERR(power->vbus_v);
+	}
+
+	power->vbus_i = devm_iio_channel_get(&pdev->dev, "vbus_i");
+	if (IS_ERR(power->vbus_i)) {
+		if (PTR_ERR(power->vbus_i) == -ENODEV)
+			return -EPROBE_DEFER;
+		return PTR_ERR(power->vbus_i);
+	}
+
+	return 0;
+}
+
+static int axp20x_configure_adc_registers(struct axp20x_usb_power *power)
+{
+	/* Enable vbus voltage and current measurement */
+	return regmap_update_bits(power->regmap, AXP20X_ADC_EN1,
+				  AXP20X_ADC_EN1_VBUS_CURR |
+				  AXP20X_ADC_EN1_VBUS_VOLT,
+				  AXP20X_ADC_EN1_VBUS_CURR |
+				  AXP20X_ADC_EN1_VBUS_VOLT);
+}
+
 static enum power_supply_property axp20x_usb_power_properties[] = {
 	POWER_SUPPLY_PROP_HEALTH,
 	POWER_SUPPLY_PROP_PRESENT,
@@ -505,6 +541,9 @@ static const struct axp_data axp192_data = {
 	.curr_lim_fld   = REG_FIELD(AXP20X_VBUS_IPSOUT_MGMT, 0, 1),
 	.vbus_valid_bit = REG_FIELD(AXP192_USB_OTG_STATUS, 2, 2),
 	.vbus_mon_bit   = REG_FIELD(AXP20X_VBUS_MON, 3, 3),
+	.axp20x_read_vbus = &axp20x_usb_power_poll_vbus,
+	.axp20x_cfg_iio_chan = axp20x_configure_iio_channels,
+	.axp20x_cfg_adc_reg = axp20x_configure_adc_registers,
 };
 
 static const struct axp_data axp202_data = {
@@ -516,6 +555,9 @@ static const struct axp_data axp202_data = {
 	.curr_lim_fld   = REG_FIELD(AXP20X_VBUS_IPSOUT_MGMT, 0, 1),
 	.vbus_valid_bit = REG_FIELD(AXP20X_USB_OTG_STATUS, 2, 2),
 	.vbus_mon_bit   = REG_FIELD(AXP20X_VBUS_MON, 3, 3),
+	.axp20x_read_vbus = &axp20x_usb_power_poll_vbus,
+	.axp20x_cfg_iio_chan = axp20x_configure_iio_channels,
+	.axp20x_cfg_adc_reg = axp20x_configure_adc_registers,
 };
 
 static const struct axp_data axp221_data = {
@@ -526,6 +568,9 @@ static const struct axp_data axp221_data = {
 	.curr_lim_table_size = ARRAY_SIZE(axp221_usb_curr_lim_table),
 	.curr_lim_fld   = REG_FIELD(AXP20X_VBUS_IPSOUT_MGMT, 0, 1),
 	.vbus_needs_polling = true,
+	.axp20x_read_vbus = &axp20x_usb_power_poll_vbus,
+	.axp20x_cfg_iio_chan = axp20x_configure_iio_channels,
+	.axp20x_cfg_adc_reg = axp20x_configure_adc_registers,
 };
 
 static const struct axp_data axp223_data = {
@@ -536,6 +581,9 @@ static const struct axp_data axp223_data = {
 	.curr_lim_table_size = ARRAY_SIZE(axp20x_usb_curr_lim_table),
 	.curr_lim_fld   = REG_FIELD(AXP20X_VBUS_IPSOUT_MGMT, 0, 1),
 	.vbus_needs_polling = true,
+	.axp20x_read_vbus = &axp20x_usb_power_poll_vbus,
+	.axp20x_cfg_iio_chan = axp20x_configure_iio_channels,
+	.axp20x_cfg_adc_reg = axp20x_configure_adc_registers,
 };
 
 static const struct axp_data axp813_data = {
@@ -549,6 +597,9 @@ static const struct axp_data axp813_data = {
 	.usb_bc_det_fld = REG_FIELD(AXP288_BC_DET_STAT, 5, 7),
 	.vbus_disable_bit = REG_FIELD(AXP20X_VBUS_IPSOUT_MGMT, 7, 7),
 	.vbus_needs_polling = true,
+	.axp20x_read_vbus = &axp20x_usb_power_poll_vbus,
+	.axp20x_cfg_iio_chan = axp20x_configure_iio_channels,
+	.axp20x_cfg_adc_reg = axp20x_configure_adc_registers,
 };
 
 #ifdef CONFIG_PM_SLEEP
@@ -590,36 +641,6 @@ static int axp20x_usb_power_resume(struct device *dev)
 static SIMPLE_DEV_PM_OPS(axp20x_usb_power_pm_ops, axp20x_usb_power_suspend,
 						  axp20x_usb_power_resume);
 
-static int configure_iio_channels(struct platform_device *pdev,
-				  struct axp20x_usb_power *power)
-{
-	power->vbus_v = devm_iio_channel_get(&pdev->dev, "vbus_v");
-	if (IS_ERR(power->vbus_v)) {
-		if (PTR_ERR(power->vbus_v) == -ENODEV)
-			return -EPROBE_DEFER;
-		return PTR_ERR(power->vbus_v);
-	}
-
-	power->vbus_i = devm_iio_channel_get(&pdev->dev, "vbus_i");
-	if (IS_ERR(power->vbus_i)) {
-		if (PTR_ERR(power->vbus_i) == -ENODEV)
-			return -EPROBE_DEFER;
-		return PTR_ERR(power->vbus_i);
-	}
-
-	return 0;
-}
-
-static int configure_adc_registers(struct axp20x_usb_power *power)
-{
-	/* Enable vbus voltage and current measurement */
-	return regmap_update_bits(power->regmap, AXP20X_ADC_EN1,
-				  AXP20X_ADC_EN1_VBUS_CURR |
-				  AXP20X_ADC_EN1_VBUS_VOLT,
-				  AXP20X_ADC_EN1_VBUS_CURR |
-				  AXP20X_ADC_EN1_VBUS_VOLT);
-}
-
 static int axp20x_regmap_field_alloc_optional(struct device *dev,
 					      struct regmap *regmap,
 					      struct reg_field fdesc,
@@ -707,7 +728,7 @@ static int axp20x_usb_power_probe(struct platform_device *pdev)
 		return ret;
 
 	ret = devm_delayed_work_autocancel(&pdev->dev, &power->vbus_detect,
-					   axp20x_usb_power_poll_vbus);
+					   axp_data->axp20x_read_vbus);
 	if (ret)
 		return ret;
 
@@ -718,9 +739,9 @@ static int axp20x_usb_power_probe(struct platform_device *pdev)
 			return ret;
 
 		if (IS_ENABLED(CONFIG_AXP20X_ADC))
-			ret = configure_iio_channels(pdev, power);
+			ret = axp_data->axp20x_cfg_iio_chan(pdev, power);
 		else
-			ret = configure_adc_registers(power);
+			ret = axp_data->axp20x_cfg_adc_reg(power);
 
 		if (ret)
 			return ret;
-- 
2.34.1

[PATCH V3 05/15] dt-bindings: power: supply: axp20x: Add input-current-limit-microamp

[Chris Morgan]

From: Chris Morgan <macromorgan@hotmail.com>

Allow specifying a hard limit of the maximum input current. Some PMICs
such as the AXP717 can pull up to 3.25A, so allow a value to be
specified that clamps this in the event the hardware is not designed
for it.

Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
---
 .../x-powers,axp20x-usb-power-supply.yaml     | 69 ++++++++++++++++++-
 1 file changed, 66 insertions(+), 3 deletions(-)

diff --git a/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-usb-power-supply.yaml b/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-usb-power-supply.yaml
index 34b7959d6772..9cc300e78f60 100644
--- a/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-usb-power-supply.yaml
+++ b/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-usb-power-supply.yaml
@@ -15,9 +15,6 @@ maintainers:
   - Chen-Yu Tsai <wens@csie.org>
   - Sebastian Reichel <sre@kernel.org>
 
-allOf:
-  - $ref: power-supply.yaml#
-
 properties:
   compatible:
     oneOf:
@@ -31,8 +28,74 @@ properties:
           - const: x-powers,axp803-usb-power-supply
           - const: x-powers,axp813-usb-power-supply
 
+  input-current-limit-microamp:
+    description:
+      Optional value to clamp the maximum input current limit to for
+      the device. If omitted, the programmed value from the EFUSE will
+      be used.
 
 required:
   - compatible
 
+allOf:
+  - $ref: power-supply.yaml#
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - x-powers,axp192-usb-power-supply
+    then:
+      properties:
+        input-current-limit-microamp:
+          enum: [100000, 500000]
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - x-powers,axp202-usb-power-supply
+              - x-powers,axp223-usb-power-supply
+    then:
+      properties:
+        input-current-limit-microamp:
+          enum: [100000, 500000, 900000]
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - x-powers,axp221-usb-power-supply
+    then:
+      properties:
+        input-current-limit-microamp:
+          enum: [500000, 900000]
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - x-powers,axp717-usb-power-supply
+    then:
+      properties:
+        input-current-limit-microamp:
+          description: Maximum input current in increments of 50000 uA.
+          minimum: 100000
+          maximum: 3250000
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - x-powers,axp813-usb-power-supply
+    then:
+      properties:
+        input-current-limit-microamp:
+          enum: [100000, 500000, 900000, 1500000, 2000000, 2500000,
+                 3000000, 3500000, 4000000]
+
 additionalProperties: false
-- 
2.34.1

Re: [PATCH V3 05/15] dt-bindings: power: supply: axp20x: Add input-current-limit-microamp

[Krzysztof Kozlowski]

On Mon, Aug 19, 2024 at 11:46:09AM -0500, Chris Morgan wrote:
> From: Chris Morgan <macromorgan@hotmail.com>
> 
> Allow specifying a hard limit of the maximum input current. Some PMICs
> such as the AXP717 can pull up to 3.25A, so allow a value to be
> specified that clamps this in the event the hardware is not designed
> for it.
> 
> Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
> ---
>  .../x-powers,axp20x-usb-power-supply.yaml     | 69 ++++++++++++++++++-
>  1 file changed, 66 insertions(+), 3 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-usb-power-supply.yaml b/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-usb-power-supply.yaml
> index 34b7959d6772..9cc300e78f60 100644
> --- a/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-usb-power-supply.yaml
> +++ b/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-usb-power-supply.yaml
> @@ -15,9 +15,6 @@ maintainers:
>    - Chen-Yu Tsai <wens@csie.org>
>    - Sebastian Reichel <sre@kernel.org>
>  
> -allOf:
> -  - $ref: power-supply.yaml#
> -
>  properties:
>    compatible:
>      oneOf:
> @@ -31,8 +28,74 @@ properties:
>            - const: x-powers,axp803-usb-power-supply
>            - const: x-powers,axp813-usb-power-supply
>  
> +  input-current-limit-microamp:
> +    description:
> +      Optional value to clamp the maximum input current limit to for
> +      the device. If omitted, the programmed value from the EFUSE will
> +      be used.

minimum: 100000
maximum: 4000000
(or whatever the values are)

Best regards,
Krzysztof

Re: [PATCH V3 05/15] dt-bindings: power: supply: axp20x: Add input-current-limit-microamp

[Chris Morgan]

On Tue, Aug 20, 2024 at 09:42:06AM +0200, Krzysztof Kozlowski wrote:
> On Mon, Aug 19, 2024 at 11:46:09AM -0500, Chris Morgan wrote:
> > From: Chris Morgan <macromorgan@hotmail.com>
> > 
> > Allow specifying a hard limit of the maximum input current. Some PMICs
> > such as the AXP717 can pull up to 3.25A, so allow a value to be
> > specified that clamps this in the event the hardware is not designed
> > for it.
> > 
> > Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
> > ---
> >  .../x-powers,axp20x-usb-power-supply.yaml     | 69 ++++++++++++++++++-
> >  1 file changed, 66 insertions(+), 3 deletions(-)
> > 
> > diff --git a/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-usb-power-supply.yaml b/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-usb-power-supply.yaml
> > index 34b7959d6772..9cc300e78f60 100644
> > --- a/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-usb-power-supply.yaml
> > +++ b/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-usb-power-supply.yaml
> > @@ -15,9 +15,6 @@ maintainers:
> >    - Chen-Yu Tsai <wens@csie.org>
> >    - Sebastian Reichel <sre@kernel.org>
> >  
> > -allOf:
> > -  - $ref: power-supply.yaml#
> > -
> >  properties:
> >    compatible:
> >      oneOf:
> > @@ -31,8 +28,74 @@ properties:
> >            - const: x-powers,axp803-usb-power-supply
> >            - const: x-powers,axp813-usb-power-supply
> >  
> > +  input-current-limit-microamp:
> > +    description:
> > +      Optional value to clamp the maximum input current limit to for
> > +      the device. If omitted, the programmed value from the EFUSE will
> > +      be used.
> 
> minimum: 100000
> maximum: 4000000
> (or whatever the values are)

It varies based on the compatible string. I've added all of the
restrictions below. Basically all but the axp717 have a table
of values available (as an enum), and the axp717 which is added
in a subsequent commit gets added as a minimum/maximum with a
description noting that steps are in values of 50000.

Thank you.

> 
> Best regards,
> Krzysztof
> 

Re: [PATCH V3 05/15] dt-bindings: power: supply: axp20x: Add input-current-limit-microamp

[Krzysztof Kozlowski]

On 20/08/2024 22:15, Chris Morgan wrote:
> On Tue, Aug 20, 2024 at 09:42:06AM +0200, Krzysztof Kozlowski wrote:
>> On Mon, Aug 19, 2024 at 11:46:09AM -0500, Chris Morgan wrote:
>>> From: Chris Morgan <macromorgan@hotmail.com>
>>>
>>> Allow specifying a hard limit of the maximum input current. Some PMICs
>>> such as the AXP717 can pull up to 3.25A, so allow a value to be
>>> specified that clamps this in the event the hardware is not designed
>>> for it.
>>>
>>> Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
>>> ---
>>>  .../x-powers,axp20x-usb-power-supply.yaml     | 69 ++++++++++++++++++-
>>>  1 file changed, 66 insertions(+), 3 deletions(-)
>>>
>>> diff --git a/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-usb-power-supply.yaml b/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-usb-power-supply.yaml
>>> index 34b7959d6772..9cc300e78f60 100644
>>> --- a/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-usb-power-supply.yaml
>>> +++ b/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-usb-power-supply.yaml
>>> @@ -15,9 +15,6 @@ maintainers:
>>>    - Chen-Yu Tsai <wens@csie.org>
>>>    - Sebastian Reichel <sre@kernel.org>
>>>  
>>> -allOf:
>>> -  - $ref: power-supply.yaml#
>>> -
>>>  properties:
>>>    compatible:
>>>      oneOf:
>>> @@ -31,8 +28,74 @@ properties:
>>>            - const: x-powers,axp803-usb-power-supply
>>>            - const: x-powers,axp813-usb-power-supply
>>>  
>>> +  input-current-limit-microamp:
>>> +    description:
>>> +      Optional value to clamp the maximum input current limit to for
>>> +      the device. If omitted, the programmed value from the EFUSE will
>>> +      be used.
>>
>> minimum: 100000
>> maximum: 4000000
>> (or whatever the values are)
> 
> It varies based on the compatible string. I've added all of the
> restrictions below. Basically all but the axp717 have a table
> of values available (as an enum), and the axp717 which is added
> in a subsequent commit gets added as a minimum/maximum with a
> description noting that steps are in values of 50000.

And you still need widest constraints here, because there is no final
"else" for all not-matched ifs, right?

Best regards,
Krzysztof

Re: [PATCH V3 05/15] dt-bindings: power: supply: axp20x: Add input-current-limit-microamp

[Chris Morgan]

On Wed, Aug 21, 2024 at 08:37:59AM +0200, Krzysztof Kozlowski wrote:
> On 20/08/2024 22:15, Chris Morgan wrote:
> > On Tue, Aug 20, 2024 at 09:42:06AM +0200, Krzysztof Kozlowski wrote:
> >> On Mon, Aug 19, 2024 at 11:46:09AM -0500, Chris Morgan wrote:
> >>> From: Chris Morgan <macromorgan@hotmail.com>
> >>>
> >>> Allow specifying a hard limit of the maximum input current. Some PMICs
> >>> such as the AXP717 can pull up to 3.25A, so allow a value to be
> >>> specified that clamps this in the event the hardware is not designed
> >>> for it.
> >>>
> >>> Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
> >>> ---
> >>>  .../x-powers,axp20x-usb-power-supply.yaml     | 69 ++++++++++++++++++-
> >>>  1 file changed, 66 insertions(+), 3 deletions(-)
> >>>
> >>> diff --git a/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-usb-power-supply.yaml b/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-usb-power-supply.yaml
> >>> index 34b7959d6772..9cc300e78f60 100644
> >>> --- a/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-usb-power-supply.yaml
> >>> +++ b/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-usb-power-supply.yaml
> >>> @@ -15,9 +15,6 @@ maintainers:
> >>>    - Chen-Yu Tsai <wens@csie.org>
> >>>    - Sebastian Reichel <sre@kernel.org>
> >>>  
> >>> -allOf:
> >>> -  - $ref: power-supply.yaml#
> >>> -
> >>>  properties:
> >>>    compatible:
> >>>      oneOf:
> >>> @@ -31,8 +28,74 @@ properties:
> >>>            - const: x-powers,axp803-usb-power-supply
> >>>            - const: x-powers,axp813-usb-power-supply
> >>>  
> >>> +  input-current-limit-microamp:
> >>> +    description:
> >>> +      Optional value to clamp the maximum input current limit to for
> >>> +      the device. If omitted, the programmed value from the EFUSE will
> >>> +      be used.
> >>
> >> minimum: 100000
> >> maximum: 4000000
> >> (or whatever the values are)
> > 
> > It varies based on the compatible string. I've added all of the
> > restrictions below. Basically all but the axp717 have a table
> > of values available (as an enum), and the axp717 which is added
> > in a subsequent commit gets added as a minimum/maximum with a
> > description noting that steps are in values of 50000.
> 
> And you still need widest constraints here, because there is no final
> "else" for all not-matched ifs, right?
> 
> Best regards,
> Krzysztof
> 

That makes sense, thank you.
Chris

[PATCH V3 06/15] power: supply: axp20x_usb_power: add input-current-limit-microamp

[Chris Morgan]

From: Chris Morgan <macromorgan@hotmail.com>

Allow users to specify a maximum input current for the device. Some
devices allow up to 3.25A of input current (such as the AXP717), which
may be too much for some implementations.

Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
---
 drivers/power/supply/axp20x_usb_power.c | 22 ++++++++++++++++++++++
 1 file changed, 22 insertions(+)

diff --git a/drivers/power/supply/axp20x_usb_power.c b/drivers/power/supply/axp20x_usb_power.c
index cd9e92f2ce71..69fbb5861934 100644
--- a/drivers/power/supply/axp20x_usb_power.c
+++ b/drivers/power/supply/axp20x_usb_power.c
@@ -80,6 +80,7 @@ struct axp20x_usb_power {
 	struct iio_channel *vbus_v;
 	struct iio_channel *vbus_i;
 	struct delayed_work vbus_detect;
+	int max_input_cur;
 	unsigned int old_status;
 	unsigned int online;
 	unsigned int num_irqs;
@@ -323,6 +324,13 @@ static int axp20x_usb_power_set_input_current_limit(struct axp20x_usb_power *pow
 	if (intval == -1)
 		return -EINVAL;
 
+	if (power->max_input_cur && (intval > power->max_input_cur)) {
+		dev_warn(power->dev,
+			 "reqested current %d clamped to max current %d\n",
+			 intval, power->max_input_cur);
+		intval = power->max_input_cur;
+	}
+
 	/*
 	 * BC1.2 detection can cause a race condition if we try to set a current
 	 * limit while it's in progress. When it finishes it will overwrite the
@@ -661,6 +669,18 @@ static int axp20x_regmap_field_alloc_optional(struct device *dev,
 	return 0;
 }
 
+/* Optionally allow users to specify a maximum charging current. */
+static void axp20x_usb_power_parse_dt(struct device *dev,
+				      struct axp20x_usb_power *power)
+{
+	int ret;
+
+	ret = device_property_read_u32(dev, "input-current-limit-microamp",
+				       &power->max_input_cur);
+	if (ret)
+		dev_dbg(dev, "%s() no input-current-limit specified\n", __func__);
+}
+
 static int axp20x_usb_power_probe(struct platform_device *pdev)
 {
 	struct axp20x_dev *axp20x = dev_get_drvdata(pdev->dev.parent);
@@ -697,6 +717,8 @@ static int axp20x_usb_power_probe(struct platform_device *pdev)
 	if (IS_ERR(power->curr_lim_fld))
 		return PTR_ERR(power->curr_lim_fld);
 
+	axp20x_usb_power_parse_dt(&pdev->dev, power);
+
 	ret = axp20x_regmap_field_alloc_optional(&pdev->dev, power->regmap,
 						 axp_data->vbus_valid_bit,
 						 &power->vbus_valid_bit);
-- 
2.34.1

[PATCH V3 07/15] dt-bindings: power: supply: axp20x-battery: Add monitored-battery

[Chris Morgan]

From: Chris Morgan <macromorgan@hotmail.com>

Document the monitored-battery property, which the existing driver can
use to set certain properties.

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
---
 .../power/supply/x-powers,axp20x-battery-power-supply.yaml  | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-battery-power-supply.yaml b/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-battery-power-supply.yaml
index e0b95ecbbebd..f196bf70b248 100644
--- a/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-battery-power-supply.yaml
+++ b/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-battery-power-supply.yaml
@@ -28,6 +28,12 @@ properties:
           - const: x-powers,axp813-battery-power-supply
       - const: x-powers,axp813-battery-power-supply
 
+  monitored-battery:
+    description:
+      Specifies the phandle of an optional simple-battery connected to
+      this gauge.
+    $ref: /schemas/types.yaml#/definitions/phandle
+
 required:
   - compatible
 
-- 
2.34.1

[PATCH V3 08/15] dt-bindings: iio: adc: Add AXP717 compatible

[Chris Morgan]

From: Chris Morgan <macromorgan@hotmail.com>

Add compatible binding for the axp717.

Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
---
 .../bindings/iio/adc/x-powers,axp209-adc.yaml        | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/Documentation/devicetree/bindings/iio/adc/x-powers,axp209-adc.yaml b/Documentation/devicetree/bindings/iio/adc/x-powers,axp209-adc.yaml
index d40689f233f2..1caa896fce82 100644
--- a/Documentation/devicetree/bindings/iio/adc/x-powers,axp209-adc.yaml
+++ b/Documentation/devicetree/bindings/iio/adc/x-powers,axp209-adc.yaml
@@ -37,6 +37,17 @@ description: |
    3 | batt_dischrg_i
    4 | ts_v
 
+  AXP717
+  ------
+   0 | batt_v
+   1 | ts_v
+   2 | vbus_v
+   3 | vsys_v
+   4 | pmic_temp
+   5 | batt_chrg_i
+   6 | vmid_v
+   7 | bkup_batt_v
+
   AXP813
   ------
    0 | pmic_temp
@@ -52,6 +63,7 @@ properties:
     oneOf:
       - const: x-powers,axp209-adc
       - const: x-powers,axp221-adc
+      - const: x-powers,axp717-adc
       - const: x-powers,axp813-adc
 
       - items:
-- 
2.34.1

[PATCH V3 09/15] dt-bindings: power: supply: axp20x: Add AXP717 compatible

[Chris Morgan]

From: Chris Morgan <macromorgan@hotmail.com>

Add support for the AXP717. It has BC 1.2 detection like the AXP813
and uses ADC channels like all other AXP devices, but otherwise is
very different requiring new registers for most functions.

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
---
 .../bindings/power/supply/x-powers,axp20x-usb-power-supply.yaml  | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-usb-power-supply.yaml b/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-usb-power-supply.yaml
index 9cc300e78f60..0a3b3d743d71 100644
--- a/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-usb-power-supply.yaml
+++ b/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-usb-power-supply.yaml
@@ -23,6 +23,7 @@ properties:
           - x-powers,axp202-usb-power-supply
           - x-powers,axp221-usb-power-supply
           - x-powers,axp223-usb-power-supply
+          - x-powers,axp717-usb-power-supply
           - x-powers,axp813-usb-power-supply
       - items:
           - const: x-powers,axp803-usb-power-supply
-- 
2.34.1

[PATCH V3 10/15] dt-bindings: power: supply: axp20x: Add AXP717 compatible

[Chris Morgan]

From: Chris Morgan <macromorgan@hotmail.com>

Add binding information for AXP717.

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
---
 .../power/supply/x-powers,axp20x-battery-power-supply.yaml       | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-battery-power-supply.yaml b/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-battery-power-supply.yaml
index f196bf70b248..5ccd375eb294 100644
--- a/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-battery-power-supply.yaml
+++ b/Documentation/devicetree/bindings/power/supply/x-powers,axp20x-battery-power-supply.yaml
@@ -23,6 +23,7 @@ properties:
       - const: x-powers,axp202-battery-power-supply
       - const: x-powers,axp209-battery-power-supply
       - const: x-powers,axp221-battery-power-supply
+      - const: x-powers,axp717-battery-power-supply
       - items:
           - const: x-powers,axp803-battery-power-supply
           - const: x-powers,axp813-battery-power-supply
-- 
2.34.1

[PATCH V3 11/15] mfd: axp20x: Add ADC, BAT, and USB cells for AXP717

[Chris Morgan]

From: Chris Morgan <macromorgan@hotmail.com>

Add support for the AXP717 PMIC to utilize the ADC (for reading
voltage, current, and temperature information from the PMIC) as well
as the USB charger and battery.

Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
---
 drivers/mfd/axp20x.c       | 25 ++++++++++++++++++++++++-
 include/linux/mfd/axp20x.h | 27 +++++++++++++++++++++++++++
 2 files changed, 51 insertions(+), 1 deletion(-)

diff --git a/drivers/mfd/axp20x.c b/drivers/mfd/axp20x.c
index dacd3c96c9f5..4051551757f2 100644
--- a/drivers/mfd/axp20x.c
+++ b/drivers/mfd/axp20x.c
@@ -209,13 +209,23 @@ static const struct regmap_access_table axp313a_volatile_table = {
 };
 
 static const struct regmap_range axp717_writeable_ranges[] = {
+	regmap_reg_range(AXP717_PMU_FAULT, AXP717_MODULE_EN_CONTROL_1),
+	regmap_reg_range(AXP717_MIN_SYS_V_CONTROL, AXP717_BOOST_CONTROL),
+	regmap_reg_range(AXP717_VSYS_V_POWEROFF, AXP717_VSYS_V_POWEROFF),
 	regmap_reg_range(AXP717_IRQ0_EN, AXP717_IRQ4_EN),
 	regmap_reg_range(AXP717_IRQ0_STATE, AXP717_IRQ4_STATE),
+	regmap_reg_range(AXP717_ICC_CHG_SET, AXP717_CV_CHG_SET),
 	regmap_reg_range(AXP717_DCDC_OUTPUT_CONTROL, AXP717_CPUSLDO_CONTROL),
+	regmap_reg_range(AXP717_ADC_CH_EN_CONTROL, AXP717_ADC_CH_EN_CONTROL),
+	regmap_reg_range(AXP717_ADC_DATA_SEL, AXP717_ADC_DATA_SEL),
 };
 
 static const struct regmap_range axp717_volatile_ranges[] = {
+	regmap_reg_range(AXP717_ON_INDICATE, AXP717_PMU_FAULT),
 	regmap_reg_range(AXP717_IRQ0_STATE, AXP717_IRQ4_STATE),
+	regmap_reg_range(AXP717_BATT_PERCENT_DATA, AXP717_BATT_PERCENT_DATA),
+	regmap_reg_range(AXP717_BATT_V_H, AXP717_BATT_CHRG_I_L),
+	regmap_reg_range(AXP717_ADC_DATA_H, AXP717_ADC_DATA_L),
 };
 
 static const struct regmap_access_table axp717_writeable_table = {
@@ -308,6 +318,12 @@ static const struct resource axp22x_usb_power_supply_resources[] = {
 	DEFINE_RES_IRQ_NAMED(AXP22X_IRQ_VBUS_REMOVAL, "VBUS_REMOVAL"),
 };
 
+static const struct resource axp717_usb_power_supply_resources[] = {
+	DEFINE_RES_IRQ_NAMED(AXP717_IRQ_VBUS_OVER_V, "VBUS_OVER_V"),
+	DEFINE_RES_IRQ_NAMED(AXP717_IRQ_VBUS_PLUGIN, "VBUS_PLUGIN"),
+	DEFINE_RES_IRQ_NAMED(AXP717_IRQ_VBUS_REMOVAL, "VBUS_REMOVAL"),
+};
+
 /* AXP803 and AXP813/AXP818 share the same interrupts */
 static const struct resource axp803_usb_power_supply_resources[] = {
 	DEFINE_RES_IRQ_NAMED(AXP803_IRQ_VBUS_PLUGIN, "VBUS_PLUGIN"),
@@ -422,7 +438,7 @@ static const struct regmap_config axp717_regmap_config = {
 	.val_bits = 8,
 	.wr_table = &axp717_writeable_table,
 	.volatile_table = &axp717_volatile_table,
-	.max_register = AXP717_CPUSLDO_CONTROL,
+	.max_register = AXP717_ADC_DATA_L,
 	.cache_type = REGCACHE_MAPLE,
 };
 
@@ -1024,6 +1040,13 @@ static struct mfd_cell axp313a_cells[] = {
 static struct mfd_cell axp717_cells[] = {
 	MFD_CELL_NAME("axp20x-regulator"),
 	MFD_CELL_RES("axp20x-pek", axp717_pek_resources),
+	MFD_CELL_OF("axp717-adc",
+		    NULL, NULL, 0, 0, "x-powers,axp717-adc"),
+	MFD_CELL_OF("axp20x-usb-power-supply",
+		    axp717_usb_power_supply_resources, NULL, 0, 0,
+		    "x-powers,axp717-usb-power-supply"),
+	MFD_CELL_OF("axp20x-battery-power-supply",
+		    NULL, NULL, 0, 0, "x-powers,axp717-battery-power-supply"),
 };
 
 static const struct resource axp288_adc_resources[] = {
diff --git a/include/linux/mfd/axp20x.h b/include/linux/mfd/axp20x.h
index 8c0a33a2e9ce..f4dfc1871a95 100644
--- a/include/linux/mfd/axp20x.h
+++ b/include/linux/mfd/axp20x.h
@@ -115,6 +115,16 @@ enum axp20x_variants {
 #define AXP313A_IRQ_STATE		0x21
 
 #define AXP717_ON_INDICATE		0x00
+#define AXP717_PMU_STATUS_2		0x01
+#define AXP717_BC_DETECT		0x05
+#define AXP717_PMU_FAULT		0x08
+#define AXP717_MODULE_EN_CONTROL_1	0x0b
+#define AXP717_MIN_SYS_V_CONTROL	0x15
+#define AXP717_INPUT_VOL_LIMIT_CTRL	0x16
+#define AXP717_INPUT_CUR_LIMIT_CTRL	0x17
+#define AXP717_MODULE_EN_CONTROL_2	0x19
+#define AXP717_BOOST_CONTROL		0x1e
+#define AXP717_VSYS_V_POWEROFF		0x24
 #define AXP717_IRQ0_EN			0x40
 #define AXP717_IRQ1_EN			0x41
 #define AXP717_IRQ2_EN			0x42
@@ -125,6 +135,9 @@ enum axp20x_variants {
 #define AXP717_IRQ2_STATE		0x4a
 #define AXP717_IRQ3_STATE		0x4b
 #define AXP717_IRQ4_STATE		0x4c
+#define AXP717_ICC_CHG_SET		0x62
+#define AXP717_ITERM_CHG_SET		0x63
+#define AXP717_CV_CHG_SET		0x64
 #define AXP717_DCDC_OUTPUT_CONTROL	0x80
 #define AXP717_DCDC1_CONTROL		0x83
 #define AXP717_DCDC2_CONTROL		0x84
@@ -145,6 +158,19 @@ enum axp20x_variants {
 #define AXP717_CLDO3_CONTROL		0x9d
 #define AXP717_CLDO4_CONTROL		0x9e
 #define AXP717_CPUSLDO_CONTROL		0x9f
+#define AXP717_BATT_PERCENT_DATA	0xa4
+#define AXP717_ADC_CH_EN_CONTROL	0xc0
+#define AXP717_BATT_V_H			0xc4
+#define AXP717_BATT_V_L			0xc5
+#define AXP717_VBUS_V_H			0xc6
+#define AXP717_VBUS_V_L			0xc7
+#define AXP717_VSYS_V_H			0xc8
+#define AXP717_VSYS_V_L			0xc9
+#define AXP717_BATT_CHRG_I_H		0xca
+#define AXP717_BATT_CHRG_I_L		0xcb
+#define AXP717_ADC_DATA_SEL		0xcd
+#define AXP717_ADC_DATA_H		0xce
+#define AXP717_ADC_DATA_L		0xcf
 
 #define AXP806_STARTUP_SRC		0x00
 #define AXP806_CHIP_ID			0x03
@@ -484,6 +510,7 @@ enum {
 	AXP717_CLDO3,
 	AXP717_CLDO4,
 	AXP717_CPUSLDO,
+	AXP717_BOOST,
 	AXP717_REG_ID_MAX,
 };
 
-- 
2.34.1

[PATCH V3 12/15] iio: adc: axp20x_adc: add support for AXP717 ADC

[Chris Morgan]

From: Chris Morgan <macromorgan@hotmail.com>

Add support for the AXP717 ADC. The AXP717 differs from other ADCs
in this series by utilizing a 14 bit ADC for all channels (a full 16
bits with the first 2 digits reserved). It also differs by lacking a
battery discharge current channel.

Note that while the current charge channel itself is included in this
driver for the AXP717 and listed in the datasheet, no scale or offset
was given for this channel. For now no scale or offset is provided in
this driver.

Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
---
 drivers/iio/adc/axp20x_adc.c | 160 +++++++++++++++++++++++++++++++++++
 1 file changed, 160 insertions(+)

diff --git a/drivers/iio/adc/axp20x_adc.c b/drivers/iio/adc/axp20x_adc.c
index 368ba6ee7a80..d43c8d124a0c 100644
--- a/drivers/iio/adc/axp20x_adc.c
+++ b/drivers/iio/adc/axp20x_adc.c
@@ -5,6 +5,7 @@
  *	Quentin Schulz <quentin.schulz@free-electrons.com>
  */
 
+#include <asm/unaligned.h>
 #include <linux/bitfield.h>
 #include <linux/completion.h>
 #include <linux/interrupt.h>
@@ -30,6 +31,8 @@
 
 #define AXP22X_ADC_EN1_MASK			(GENMASK(7, 5) | BIT(0))
 
+#define AXP717_ADC_EN1_MASK			GENMASK(7, 0)
+
 #define AXP192_GPIO30_IN_RANGE_GPIO0		BIT(0)
 #define AXP192_GPIO30_IN_RANGE_GPIO1		BIT(1)
 #define AXP192_GPIO30_IN_RANGE_GPIO2		BIT(2)
@@ -43,6 +46,13 @@
 
 #define AXP22X_ADC_RATE_HZ(x)			((ilog2((x) / 100) << 6) & AXP20X_ADC_RATE_MASK)
 
+#define AXP717_ADC_DATA_TS			0x00
+#define AXP717_ADC_DATA_TEMP			0x01
+#define AXP717_ADC_DATA_VMID			0x02
+#define AXP717_ADC_DATA_BKUP_BATT		0x03
+
+#define AXP717_ADC_DATA_MASK			GENMASK(13, 0)
+
 #define AXP813_V_I_ADC_RATE_MASK		GENMASK(5, 4)
 #define AXP813_ADC_RATE_MASK			(AXP20X_ADC_RATE_MASK | AXP813_V_I_ADC_RATE_MASK)
 #define AXP813_TS_GPIO0_ADC_RATE_HZ(x)		AXP20X_ADC_RATE_HZ(x)
@@ -125,6 +135,20 @@ enum axp22x_adc_channel_i {
 	AXP22X_BATT_DISCHRG_I,
 };
 
+enum axp717_adc_channel_v {
+	AXP717_BATT_V = 0,
+	AXP717_TS_IN,
+	AXP717_VBUS_V,
+	AXP717_VSYS_V,
+	AXP717_DIE_TEMP_V,
+	AXP717_VMID_V = 6,
+	AXP717_BKUP_BATT_V,
+};
+
+enum axp717_adc_channel_i {
+	AXP717_BATT_CHRG_I = 5,
+};
+
 enum axp813_adc_channel_v {
 	AXP813_TS_IN = 0,
 	AXP813_GPIO0_V,
@@ -179,6 +203,22 @@ static struct iio_map axp22x_maps[] = {
 	}, { /* sentinel */ }
 };
 
+static struct iio_map axp717_maps[] = {
+	{
+		.consumer_dev_name = "axp20x-usb-power-supply",
+		.consumer_channel = "vbus_v",
+		.adc_channel_label = "vbus_v",
+	}, {
+		.consumer_dev_name = "axp20x-battery-power-supply",
+		.consumer_channel = "batt_v",
+		.adc_channel_label = "batt_v",
+	}, {
+		.consumer_dev_name = "axp20x-battery-power-supply",
+		.consumer_channel = "batt_chrg_i",
+		.adc_channel_label = "batt_chrg_i",
+	},
+};
+
 /*
  * Channels are mapped by physical system. Their channels share the same index.
  * i.e. acin_i is in_current0_raw and acin_v is in_voltage0_raw.
@@ -274,6 +314,29 @@ static const struct iio_chan_spec axp22x_adc_channels[] = {
 			   AXP22X_TS_ADC_H),
 };
 
+/*
+ * Scale and offset is unknown for temp, ts, batt_chrg_i, vmid_v, and
+ * bkup_batt_v channels. Leaving scale and offset undefined for now.
+ */
+static const struct iio_chan_spec axp717_adc_channels[] = {
+	AXP20X_ADC_CHANNEL(AXP717_BATT_V, "batt_v", IIO_VOLTAGE,
+			   AXP717_BATT_V_H),
+	AXP20X_ADC_CHANNEL(AXP717_TS_IN, "ts_v", IIO_VOLTAGE,
+			   AXP717_ADC_DATA_H),
+	AXP20X_ADC_CHANNEL(AXP717_VBUS_V, "vbus_v", IIO_VOLTAGE,
+			   AXP717_VBUS_V_H),
+	AXP20X_ADC_CHANNEL(AXP717_VSYS_V, "vsys_v", IIO_VOLTAGE,
+			   AXP717_VSYS_V_H),
+	AXP20X_ADC_CHANNEL(AXP717_DIE_TEMP_V, "pmic_temp", IIO_TEMP,
+			   AXP717_ADC_DATA_H),
+	AXP20X_ADC_CHANNEL(AXP717_BATT_CHRG_I, "batt_chrg_i", IIO_CURRENT,
+			   AXP717_BATT_CHRG_I_H),
+	AXP20X_ADC_CHANNEL(AXP717_VMID_V, "vmid_v", IIO_VOLTAGE,
+			   AXP717_ADC_DATA_H),
+	AXP20X_ADC_CHANNEL(AXP717_BKUP_BATT_V, "bkup_batt_v", IIO_VOLTAGE,
+			   AXP717_ADC_DATA_H),
+};
+
 static const struct iio_chan_spec axp813_adc_channels[] = {
 	{
 		.type = IIO_TEMP,
@@ -354,6 +417,51 @@ static int axp22x_adc_raw(struct iio_dev *indio_dev,
 	return IIO_VAL_INT;
 }
 
+static int axp717_adc_raw(struct iio_dev *indio_dev,
+			  struct iio_chan_spec const *chan, int *val)
+{
+	struct axp20x_adc_iio *info = iio_priv(indio_dev);
+	u8 bulk_reg[2];
+	int ret;
+
+	/*
+	 * A generic "ADC data" channel is used for TS, tdie, vmid,
+	 * and vbackup. This channel must both first be enabled and
+	 * also selected before it can be read.
+	 */
+	switch (chan->channel) {
+	case AXP717_TS_IN:
+		regmap_write(info->regmap, AXP717_ADC_DATA_SEL,
+			     AXP717_ADC_DATA_TS);
+		break;
+	case AXP717_DIE_TEMP_V:
+		regmap_write(info->regmap, AXP717_ADC_DATA_SEL,
+			     AXP717_ADC_DATA_TEMP);
+		break;
+	case AXP717_VMID_V:
+		regmap_write(info->regmap, AXP717_ADC_DATA_SEL,
+			     AXP717_ADC_DATA_VMID);
+		break;
+	case AXP717_BKUP_BATT_V:
+		regmap_write(info->regmap, AXP717_ADC_DATA_SEL,
+			     AXP717_ADC_DATA_BKUP_BATT);
+		break;
+	default:
+		break;
+	}
+
+	/*
+	 * All channels are 14 bits, with the first 2 bits on the high
+	 * register reserved and the remaining bits as the ADC value.
+	 */
+	ret = regmap_bulk_read(info->regmap, chan->address, bulk_reg, 2);
+	if (ret < 0)
+		return ret;
+
+	*val = FIELD_GET(AXP717_ADC_DATA_MASK, get_unaligned_be16(bulk_reg));
+	return IIO_VAL_INT;
+}
+
 static int axp813_adc_raw(struct iio_dev *indio_dev,
 			  struct iio_chan_spec const *chan, int *val)
 {
@@ -571,6 +679,27 @@ static int axp22x_adc_scale(struct iio_chan_spec const *chan, int *val,
 	}
 }
 
+static int axp717_adc_scale(struct iio_chan_spec const *chan, int *val,
+			    int *val2)
+{
+	switch (chan->type) {
+	case IIO_VOLTAGE:
+		*val = 1;
+		return IIO_VAL_INT;
+
+	case IIO_CURRENT:
+		*val = 1;
+		return IIO_VAL_INT;
+
+	case IIO_TEMP:
+		*val = 100;
+		return IIO_VAL_INT;
+
+	default:
+		return -EINVAL;
+	}
+}
+
 static int axp813_adc_scale(struct iio_chan_spec const *chan, int *val,
 			    int *val2)
 {
@@ -746,6 +875,22 @@ static int axp22x_read_raw(struct iio_dev *indio_dev,
 	}
 }
 
+static int axp717_read_raw(struct iio_dev *indio_dev,
+			   struct iio_chan_spec const *chan, int *val,
+			   int *val2, long mask)
+{
+	switch (mask) {
+	case IIO_CHAN_INFO_SCALE:
+		return axp717_adc_scale(chan, val, val2);
+
+	case IIO_CHAN_INFO_RAW:
+		return axp717_adc_raw(indio_dev, chan, val);
+
+	default:
+		return -EINVAL;
+	}
+}
+
 static int axp813_read_raw(struct iio_dev *indio_dev,
 			   struct iio_chan_spec const *chan, int *val,
 			   int *val2, long mask)
@@ -860,6 +1005,10 @@ static const struct iio_info axp22x_adc_iio_info = {
 	.read_raw = axp22x_read_raw,
 };
 
+static const struct iio_info axp717_adc_iio_info = {
+	.read_raw = axp717_read_raw,
+};
+
 static const struct iio_info axp813_adc_iio_info = {
 	.read_raw = axp813_read_raw,
 };
@@ -930,6 +1079,15 @@ static const struct axp_data axp22x_data = {
 	.maps = axp22x_maps,
 };
 
+static const struct axp_data axp717_data = {
+	.iio_info = &axp717_adc_iio_info,
+	.num_channels = ARRAY_SIZE(axp717_adc_channels),
+	.channels = axp717_adc_channels,
+	.adc_en1 = AXP717_ADC_CH_EN_CONTROL,
+	.adc_en1_mask = AXP717_ADC_EN1_MASK,
+	.maps = axp717_maps,
+};
+
 static const struct axp_data axp813_data = {
 	.iio_info = &axp813_adc_iio_info,
 	.num_channels = ARRAY_SIZE(axp813_adc_channels),
@@ -944,6 +1102,7 @@ static const struct of_device_id axp20x_adc_of_match[] = {
 	{ .compatible = "x-powers,axp192-adc", .data = (void *)&axp192_data, },
 	{ .compatible = "x-powers,axp209-adc", .data = (void *)&axp20x_data, },
 	{ .compatible = "x-powers,axp221-adc", .data = (void *)&axp22x_data, },
+	{ .compatible = "x-powers,axp717-adc", .data = (void *)&axp717_data, },
 	{ .compatible = "x-powers,axp813-adc", .data = (void *)&axp813_data, },
 	{ /* sentinel */ }
 };
@@ -953,6 +1112,7 @@ static const struct platform_device_id axp20x_adc_id_match[] = {
 	{ .name = "axp192-adc", .driver_data = (kernel_ulong_t)&axp192_data, },
 	{ .name = "axp20x-adc", .driver_data = (kernel_ulong_t)&axp20x_data, },
 	{ .name = "axp22x-adc", .driver_data = (kernel_ulong_t)&axp22x_data, },
+	{ .name = "axp717-adc", .driver_data = (kernel_ulong_t)&axp717_data, },
 	{ .name = "axp813-adc", .driver_data = (kernel_ulong_t)&axp813_data, },
 	{ /* sentinel */ },
 };
-- 
2.34.1

[PATCH V3 13/15] power: supply: axp20x_usb_power: Add support for AXP717

[Chris Morgan]

From: Chris Morgan <macromorgan@hotmail.com>

Add support for the AXP717 PMIC. The AXP717 PMIC allows for detection
of USB type like the AXP813, but has little in common otherwise with
the other AXP PMICs. The USB charger is able to provide between
100000uA and 3250000uA of power, and can measure the VBUS input in mV
with up to 14 bits of precision.

Tested-by: Philippe Simons <simons.philippe@gmail.com>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
---
 drivers/power/supply/axp20x_usb_power.c | 244 ++++++++++++++++++++++++
 1 file changed, 244 insertions(+)

diff --git a/drivers/power/supply/axp20x_usb_power.c b/drivers/power/supply/axp20x_usb_power.c
index 69fbb5861934..41426fca8cfc 100644
--- a/drivers/power/supply/axp20x_usb_power.c
+++ b/drivers/power/supply/axp20x_usb_power.c
@@ -30,8 +30,13 @@
 #define AXP20X_PWR_STATUS_VBUS_PRESENT	BIT(5)
 #define AXP20X_PWR_STATUS_VBUS_USED	BIT(4)
 
+#define AXP717_PWR_STATUS_VBUS_GOOD	BIT(5)
+
 #define AXP20X_USB_STATUS_VBUS_VALID	BIT(2)
 
+#define AXP717_PMU_FAULT_VBUS		BIT(5)
+#define AXP717_PMU_FAULT_VSYS		BIT(3)
+
 #define AXP20X_VBUS_VHOLD_uV(b)		(4000000 + (((b) >> 3) & 7) * 100000)
 #define AXP20X_VBUS_VHOLD_MASK		GENMASK(5, 3)
 #define AXP20X_VBUS_VHOLD_OFFSET	3
@@ -39,6 +44,12 @@
 #define AXP20X_ADC_EN1_VBUS_CURR	BIT(2)
 #define AXP20X_ADC_EN1_VBUS_VOLT	BIT(3)
 
+#define AXP717_INPUT_VOL_LIMIT_MASK	GENMASK(3, 0)
+#define AXP717_INPUT_CUR_LIMIT_MASK	GENMASK(5, 0)
+#define AXP717_ADC_DATA_MASK		GENMASK(14, 0)
+
+#define AXP717_ADC_EN_VBUS_VOLT		BIT(2)
+
 /*
  * Note do not raise the debounce time, we must report Vusb high within
  * 100ms otherwise we get Vbus errors in musb.
@@ -143,6 +154,24 @@ static void axp20x_usb_power_poll_vbus(struct work_struct *work)
 		mod_delayed_work(system_power_efficient_wq, &power->vbus_detect, DEBOUNCE_TIME);
 }
 
+static void axp717_usb_power_poll_vbus(struct work_struct *work)
+{
+	struct axp20x_usb_power *power =
+		container_of(work, struct axp20x_usb_power, vbus_detect.work);
+	unsigned int val;
+	int ret;
+
+	ret = regmap_read(power->regmap, AXP717_ON_INDICATE, &val);
+	if (ret)
+		return;
+
+	val &= AXP717_PWR_STATUS_VBUS_GOOD;
+	if (val != power->old_status)
+		power_supply_changed(power->supply);
+
+	power->old_status = val;
+}
+
 static int axp20x_get_usb_type(struct axp20x_usb_power *power,
 			       union power_supply_propval *val)
 {
@@ -288,6 +317,91 @@ static int axp20x_usb_power_get_property(struct power_supply *psy,
 	return 0;
 }
 
+static int axp717_usb_power_get_property(struct power_supply *psy,
+	enum power_supply_property psp, union power_supply_propval *val)
+{
+	struct axp20x_usb_power *power = power_supply_get_drvdata(psy);
+	unsigned int v;
+	int ret;
+
+	switch (psp) {
+	case POWER_SUPPLY_PROP_HEALTH:
+		val->intval = POWER_SUPPLY_HEALTH_GOOD;
+		ret = regmap_read(power->regmap, AXP717_ON_INDICATE, &v);
+		if (ret)
+			return ret;
+
+		if (!(v & AXP717_PWR_STATUS_VBUS_GOOD))
+			val->intval = POWER_SUPPLY_HEALTH_UNKNOWN;
+
+		ret = regmap_read(power->regmap, AXP717_PMU_FAULT_VBUS, &v);
+		if (ret)
+			return ret;
+
+		v &= (AXP717_PMU_FAULT_VBUS | AXP717_PMU_FAULT_VSYS);
+		if (v) {
+			val->intval = POWER_SUPPLY_HEALTH_OVERVOLTAGE;
+			regmap_write(power->regmap, AXP717_PMU_FAULT_VBUS, v);
+		}
+
+		break;
+	case POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT:
+		ret = regmap_read(power->regmap, AXP717_INPUT_CUR_LIMIT_CTRL, &v);
+		if (ret)
+			return ret;
+
+		/* 50ma step size with 100ma offset. */
+		v &= AXP717_INPUT_CUR_LIMIT_MASK;
+		val->intval = (v * 50000) + 100000;
+		break;
+	case POWER_SUPPLY_PROP_ONLINE:
+	case POWER_SUPPLY_PROP_PRESENT:
+		ret = regmap_read(power->regmap, AXP717_ON_INDICATE, &v);
+		if (ret)
+			return ret;
+		val->intval = !!(v & AXP717_PWR_STATUS_VBUS_GOOD);
+		break;
+	case POWER_SUPPLY_PROP_USB_TYPE:
+		return axp20x_get_usb_type(power, val);
+	case POWER_SUPPLY_PROP_VOLTAGE_MIN:
+		ret = regmap_read(power->regmap, AXP717_INPUT_VOL_LIMIT_CTRL, &v);
+		if (ret)
+			return ret;
+
+		/* 80mv step size with 3.88v offset. */
+		v &= AXP717_INPUT_VOL_LIMIT_MASK;
+		val->intval = (v * 80000) + 3880000;
+		break;
+	case POWER_SUPPLY_PROP_VOLTAGE_NOW:
+		if (IS_ENABLED(CONFIG_AXP20X_ADC)) {
+			ret = iio_read_channel_processed(power->vbus_v,
+							 &val->intval);
+			if (ret)
+				return ret;
+
+			/*
+			 * IIO framework gives mV but Power Supply framework
+			 * gives uV.
+			 */
+			val->intval *= 1000;
+			return 0;
+		}
+
+		ret = axp20x_read_variable_width(power->regmap,
+						 AXP717_VBUS_V_H, 16);
+		if (ret < 0)
+			return ret;
+
+		val->intval = (ret % AXP717_ADC_DATA_MASK) * 1000;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+
+}
+
 static int axp20x_usb_power_set_voltage_min(struct axp20x_usb_power *power,
 					    int intval)
 {
@@ -314,6 +428,22 @@ static int axp20x_usb_power_set_voltage_min(struct axp20x_usb_power *power,
 	return -EINVAL;
 }
 
+static int axp717_usb_power_set_voltage_min(struct axp20x_usb_power *power,
+					    int intval)
+{
+	int val;
+
+	/* Minimum value of 3.88v and maximum of 5.08v. */
+	if (intval < 3880000 || intval > 5080000)
+		return -EINVAL;
+
+	/* step size of 80ma with 3.88v offset. */
+	val = (intval - 3880000) / 80000;
+	return regmap_update_bits(power->regmap,
+				  AXP717_INPUT_VOL_LIMIT_CTRL,
+				  AXP717_INPUT_VOL_LIMIT_MASK, val);
+}
+
 static int axp20x_usb_power_set_input_current_limit(struct axp20x_usb_power *power,
 						    int intval)
 {
@@ -354,6 +484,29 @@ static int axp20x_usb_power_set_input_current_limit(struct axp20x_usb_power *pow
 	return regmap_field_write(power->curr_lim_fld, reg);
 }
 
+static int axp717_usb_power_set_input_current_limit(struct axp20x_usb_power *power,
+						    int intval)
+{
+	int tmp;
+
+	/* Minimum value of 100mA and maximum value of 3.25A*/
+	if (intval < 100000 || intval > 3250000)
+		return -EINVAL;
+
+	if (power->max_input_cur && (intval > power->max_input_cur)) {
+		dev_warn(power->dev,
+			 "reqested current %d clamped to max current %d\n",
+			 intval, power->max_input_cur);
+		intval = power->max_input_cur;
+	}
+
+	/* Minimum value of 100mA with step size of 50mA. */
+	tmp = (intval - 100000) / 50000;
+	return regmap_update_bits(power->regmap,
+				  AXP717_INPUT_CUR_LIMIT_CTRL,
+				  AXP717_INPUT_CUR_LIMIT_MASK, tmp);
+}
+
 static int axp20x_usb_power_set_property(struct power_supply *psy,
 					 enum power_supply_property psp,
 					 const union power_supply_propval *val)
@@ -376,6 +529,24 @@ static int axp20x_usb_power_set_property(struct power_supply *psy,
 	default:
 		return -EINVAL;
 	}
+}
+
+static int axp717_usb_power_set_property(struct power_supply *psy,
+					 enum power_supply_property psp,
+					 const union power_supply_propval *val)
+{
+	struct axp20x_usb_power *power = power_supply_get_drvdata(psy);
+
+	switch (psp) {
+	case POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT:
+		return axp717_usb_power_set_input_current_limit(power, val->intval);
+
+	case POWER_SUPPLY_PROP_VOLTAGE_MIN:
+		return axp717_usb_power_set_voltage_min(power, val->intval);
+
+	default:
+		return -EINVAL;
+	}
 
 	return -EINVAL;
 }
@@ -399,6 +570,13 @@ static int axp20x_usb_power_prop_writeable(struct power_supply *psy,
 	       psp == POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT;
 }
 
+static int axp717_usb_power_prop_writeable(struct power_supply *psy,
+					   enum power_supply_property psp)
+{
+	return psp == POWER_SUPPLY_PROP_VOLTAGE_MIN ||
+	       psp == POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT;
+}
+
 static int axp20x_configure_iio_channels(struct platform_device *pdev,
 					 struct axp20x_usb_power *power)
 {
@@ -419,6 +597,19 @@ static int axp20x_configure_iio_channels(struct platform_device *pdev,
 	return 0;
 }
 
+static int axp717_configure_iio_channels(struct platform_device *pdev,
+					 struct axp20x_usb_power *power)
+{
+	power->vbus_v = devm_iio_channel_get(&pdev->dev, "vbus_v");
+	if (IS_ERR(power->vbus_v)) {
+		if (PTR_ERR(power->vbus_v) == -ENODEV)
+			return -EPROBE_DEFER;
+		return PTR_ERR(power->vbus_v);
+	}
+
+	return 0;
+}
+
 static int axp20x_configure_adc_registers(struct axp20x_usb_power *power)
 {
 	/* Enable vbus voltage and current measurement */
@@ -429,6 +620,14 @@ static int axp20x_configure_adc_registers(struct axp20x_usb_power *power)
 				  AXP20X_ADC_EN1_VBUS_VOLT);
 }
 
+static int axp717_configure_adc_registers(struct axp20x_usb_power *power)
+{
+	/* Enable vbus voltage measurement  */
+	return regmap_update_bits(power->regmap, AXP717_ADC_CH_EN_CONTROL,
+				  AXP717_ADC_EN_VBUS_VOLT,
+				  AXP717_ADC_EN_VBUS_VOLT);
+}
+
 static enum power_supply_property axp20x_usb_power_properties[] = {
 	POWER_SUPPLY_PROP_HEALTH,
 	POWER_SUPPLY_PROP_PRESENT,
@@ -447,6 +646,16 @@ static enum power_supply_property axp22x_usb_power_properties[] = {
 	POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT,
 };
 
+static enum power_supply_property axp717_usb_power_properties[] = {
+	POWER_SUPPLY_PROP_HEALTH,
+	POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT,
+	POWER_SUPPLY_PROP_ONLINE,
+	POWER_SUPPLY_PROP_PRESENT,
+	POWER_SUPPLY_PROP_USB_TYPE,
+	POWER_SUPPLY_PROP_VOLTAGE_MIN,
+	POWER_SUPPLY_PROP_VOLTAGE_NOW,
+};
+
 static enum power_supply_property axp813_usb_power_properties[] = {
 	POWER_SUPPLY_PROP_HEALTH,
 	POWER_SUPPLY_PROP_PRESENT,
@@ -483,6 +692,18 @@ static const struct power_supply_desc axp22x_usb_power_desc = {
 	.set_property = axp20x_usb_power_set_property,
 };
 
+static const struct power_supply_desc axp717_usb_power_desc = {
+	.name = "axp20x-usb",
+	.type = POWER_SUPPLY_TYPE_USB,
+	.properties = axp717_usb_power_properties,
+	.num_properties = ARRAY_SIZE(axp717_usb_power_properties),
+	.property_is_writeable = axp717_usb_power_prop_writeable,
+	.get_property = axp717_usb_power_get_property,
+	.set_property = axp717_usb_power_set_property,
+	.usb_types = axp813_usb_types,
+	.num_usb_types = ARRAY_SIZE(axp813_usb_types),
+};
+
 static const struct power_supply_desc axp813_usb_power_desc = {
 	.name = "axp20x-usb",
 	.type = POWER_SUPPLY_TYPE_USB,
@@ -507,6 +728,12 @@ static const char * const axp22x_irq_names[] = {
 	"VBUS_REMOVAL",
 };
 
+static const char * const axp717_irq_names[] = {
+	"VBUS_PLUGIN",
+	"VBUS_REMOVAL",
+	"VBUS_OVER_V",
+};
+
 static int axp192_usb_curr_lim_table[] = {
 	-1,
 	-1,
@@ -594,6 +821,20 @@ static const struct axp_data axp223_data = {
 	.axp20x_cfg_adc_reg = axp20x_configure_adc_registers,
 };
 
+static const struct axp_data axp717_data = {
+	.power_desc     = &axp717_usb_power_desc,
+	.irq_names      = axp717_irq_names,
+	.num_irq_names  = ARRAY_SIZE(axp717_irq_names),
+	.curr_lim_fld   = REG_FIELD(AXP717_INPUT_CUR_LIMIT_CTRL, 0, 5),
+	.usb_bc_en_bit  = REG_FIELD(AXP717_MODULE_EN_CONTROL_1, 4, 4),
+	.usb_bc_det_fld = REG_FIELD(AXP717_BC_DETECT, 5, 7),
+	.vbus_mon_bit   = REG_FIELD(AXP717_ADC_CH_EN_CONTROL, 2, 2),
+	.vbus_needs_polling = false,
+	.axp20x_read_vbus = &axp717_usb_power_poll_vbus,
+	.axp20x_cfg_iio_chan = axp717_configure_iio_channels,
+	.axp20x_cfg_adc_reg = axp717_configure_adc_registers,
+};
+
 static const struct axp_data axp813_data = {
 	.power_desc	= &axp813_usb_power_desc,
 	.irq_names	= axp22x_irq_names,
@@ -821,6 +1062,9 @@ static const struct of_device_id axp20x_usb_power_match[] = {
 	}, {
 		.compatible = "x-powers,axp223-usb-power-supply",
 		.data = &axp223_data,
+	}, {
+		.compatible = "x-powers,axp717-usb-power-supply",
+		.data = &axp717_data,
 	}, {
 		.compatible = "x-powers,axp813-usb-power-supply",
 		.data = &axp813_data,
-- 
2.34.1

[PATCH V3 14/15] power: supply: axp20x_battery: add support for AXP717

[Chris Morgan]

From: Chris Morgan <macromorgan@hotmail.com>

Add support for the AXP717 PMIC battery charger. The AXP717 differs
greatly from existing AXP battery chargers in that it cannot measure
the discharge current. The datasheet does not document the current
value's offset or scale, so the POWER_SUPPLY_PROP_CURRENT_NOW is left
unscaled.

Tested-by: Philippe Simons <simons.philippe@gmail.com>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
---
 drivers/power/supply/axp20x_battery.c | 437 ++++++++++++++++++++++++++
 1 file changed, 437 insertions(+)

diff --git a/drivers/power/supply/axp20x_battery.c b/drivers/power/supply/axp20x_battery.c
index c903c588b361..d43c11f27de6 100644
--- a/drivers/power/supply/axp20x_battery.c
+++ b/drivers/power/supply/axp20x_battery.c
@@ -32,9 +32,19 @@
 #include <linux/mfd/axp20x.h>
 
 #define AXP20X_PWR_STATUS_BAT_CHARGING	BIT(2)
+#define AXP717_PWR_STATUS_MASK		GENMASK(6, 5)
+#define AXP717_PWR_STATUS_BAT_STANDBY	0
+#define AXP717_PWR_STATUS_BAT_CHRG	1
+#define AXP717_PWR_STATUS_BAT_DISCHRG	2
 
 #define AXP20X_PWR_OP_BATT_PRESENT	BIT(5)
 #define AXP20X_PWR_OP_BATT_ACTIVATED	BIT(3)
+#define AXP717_PWR_OP_BATT_PRESENT	BIT(3)
+
+#define AXP717_BATT_PMU_FAULT_MASK	GENMASK(2, 0)
+#define AXP717_BATT_UVLO_2_5V		BIT(2)
+#define AXP717_BATT_OVER_TEMP		BIT(1)
+#define AXP717_BATT_UNDER_TEMP		BIT(0)
 
 #define AXP209_FG_PERCENT		GENMASK(6, 0)
 #define AXP22X_FG_VALID			BIT(7)
@@ -49,11 +59,34 @@
 #define AXP22X_CHRG_CTRL1_TGT_4_22V	(1 << 5)
 #define AXP22X_CHRG_CTRL1_TGT_4_24V	(3 << 5)
 
+#define AXP717_CHRG_ENABLE		BIT(1)
+#define AXP717_CHRG_CV_VOLT_MASK	GENMASK(2, 0)
+#define AXP717_CHRG_CV_4_0V		0
+#define AXP717_CHRG_CV_4_1V		1
+#define AXP717_CHRG_CV_4_2V		2
+#define AXP717_CHRG_CV_4_35V		3
+#define AXP717_CHRG_CV_4_4V		4
+/* Values 5 and 6 reserved. */
+#define AXP717_CHRG_CV_5_0V		7
+
 #define AXP813_CHRG_CTRL1_TGT_4_35V	(3 << 5)
 
 #define AXP20X_CHRG_CTRL1_TGT_CURR	GENMASK(3, 0)
+#define AXP717_ICC_CHARGER_LIM_MASK	GENMASK(5, 0)
+
+#define AXP717_ITERM_CHG_LIM_MASK	GENMASK(3, 0)
+#define AXP717_ITERM_CC_STEP		64000
 
 #define AXP20X_V_OFF_MASK		GENMASK(2, 0)
+#define AXP717_V_OFF_MASK		GENMASK(6, 4)
+
+#define AXP717_BAT_VMIN_MIN_UV		2600000
+#define AXP717_BAT_VMIN_MAX_UV		3300000
+#define AXP717_BAT_VMIN_STEP		100000
+#define AXP717_BAT_CV_MIN_UV		4000000
+#define AXP717_BAT_CV_MAX_UV		5000000
+#define AXP717_BAT_CC_MIN_UA		0
+#define AXP717_BAT_CC_MAX_UA		3008000
 
 struct axp20x_batt_ps;
 
@@ -143,6 +176,39 @@ static int axp22x_battery_get_max_voltage(struct axp20x_batt_ps *axp20x_batt,
 	return 0;
 }
 
+static int axp717_battery_get_max_voltage(struct axp20x_batt_ps *axp20x_batt,
+					  int *val)
+{
+	int ret, reg;
+
+	ret = regmap_read(axp20x_batt->regmap, AXP717_CV_CHG_SET, &reg);
+	if (ret)
+		return ret;
+
+	switch (reg & AXP717_CHRG_CV_VOLT_MASK) {
+	case AXP717_CHRG_CV_4_0V:
+		*val = 4000000;
+		return 0;
+	case AXP717_CHRG_CV_4_1V:
+		*val = 4100000;
+		return 0;
+	case AXP717_CHRG_CV_4_2V:
+		*val = 4200000;
+		return 0;
+	case AXP717_CHRG_CV_4_35V:
+		*val = 4350000;
+		return 0;
+	case AXP717_CHRG_CV_4_4V:
+		*val = 4400000;
+		return 0;
+	case AXP717_CHRG_CV_5_0V:
+		*val = 5000000;
+		return 0;
+	default:
+		return -EINVAL;
+	}
+}
+
 static int axp813_battery_get_max_voltage(struct axp20x_batt_ps *axp20x_batt,
 					  int *val)
 {
@@ -188,6 +254,21 @@ static int axp20x_get_constant_charge_current(struct axp20x_batt_ps *axp,
 	return 0;
 }
 
+static int axp717_get_constant_charge_current(struct axp20x_batt_ps *axp,
+					      int *val)
+{
+	int ret;
+
+	ret = regmap_read(axp->regmap, AXP717_ICC_CHG_SET, val);
+	if (ret)
+		return ret;
+
+	*val = FIELD_GET(AXP717_ICC_CHARGER_LIM_MASK, *val) *
+		axp->data->ccc_scale;
+
+	return 0;
+}
+
 static int axp20x_battery_get_prop(struct power_supply *psy,
 				   enum power_supply_property psp,
 				   union power_supply_propval *val)
@@ -340,6 +421,171 @@ static int axp20x_battery_get_prop(struct power_supply *psy,
 	return 0;
 }
 
+static int axp717_battery_get_prop(struct power_supply *psy,
+				   enum power_supply_property psp,
+				   union power_supply_propval *val)
+{
+	struct axp20x_batt_ps *axp20x_batt = power_supply_get_drvdata(psy);
+	int ret = 0, reg;
+
+	switch (psp) {
+	case POWER_SUPPLY_PROP_PRESENT:
+	case POWER_SUPPLY_PROP_ONLINE:
+		ret = regmap_read(axp20x_batt->regmap, AXP717_ON_INDICATE,
+				  &reg);
+		if (ret)
+			return ret;
+
+		val->intval = FIELD_GET(AXP717_PWR_OP_BATT_PRESENT, reg);
+		return 0;
+
+	case POWER_SUPPLY_PROP_STATUS:
+		ret = regmap_read(axp20x_batt->regmap, AXP717_PMU_STATUS_2,
+				  &reg);
+		if (ret)
+			return ret;
+
+		switch (FIELD_GET(AXP717_PWR_STATUS_MASK, reg)) {
+		case AXP717_PWR_STATUS_BAT_STANDBY:
+			val->intval = POWER_SUPPLY_STATUS_NOT_CHARGING;
+			return 0;
+
+		case AXP717_PWR_STATUS_BAT_CHRG:
+			val->intval = POWER_SUPPLY_STATUS_CHARGING;
+			return 0;
+
+		case AXP717_PWR_STATUS_BAT_DISCHRG:
+			val->intval = POWER_SUPPLY_STATUS_DISCHARGING;
+			return 0;
+
+		default:
+			val->intval = POWER_SUPPLY_STATUS_UNKNOWN;
+			return 0;
+		}
+
+	/*
+	 * If a fault is detected it must also be cleared; if the
+	 * condition persists it should reappear (This is an
+	 * assumption, it's actually not documented). A restart was
+	 * not sufficient to clear the bit in testing despite the
+	 * register listed as POR.
+	 */
+	case POWER_SUPPLY_PROP_HEALTH:
+		ret = regmap_read(axp20x_batt->regmap, AXP717_PMU_FAULT,
+				  &reg);
+		if (ret)
+			return ret;
+
+		switch (reg & AXP717_BATT_PMU_FAULT_MASK) {
+		case AXP717_BATT_UVLO_2_5V:
+			val->intval = POWER_SUPPLY_HEALTH_DEAD;
+			regmap_update_bits(axp20x_batt->regmap,
+					   AXP717_PMU_FAULT,
+					   AXP717_BATT_UVLO_2_5V,
+					   AXP717_BATT_UVLO_2_5V);
+			return 0;
+
+		case AXP717_BATT_OVER_TEMP:
+			val->intval = POWER_SUPPLY_HEALTH_HOT;
+			regmap_update_bits(axp20x_batt->regmap,
+					   AXP717_PMU_FAULT,
+					   AXP717_BATT_OVER_TEMP,
+					   AXP717_BATT_OVER_TEMP);
+			return 0;
+
+		case AXP717_BATT_UNDER_TEMP:
+			val->intval = POWER_SUPPLY_HEALTH_COLD;
+			regmap_update_bits(axp20x_batt->regmap,
+					   AXP717_PMU_FAULT,
+					   AXP717_BATT_UNDER_TEMP,
+					   AXP717_BATT_UNDER_TEMP);
+			return 0;
+
+		default:
+			val->intval = POWER_SUPPLY_HEALTH_GOOD;
+			return 0;
+		}
+
+	case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX:
+		ret = axp717_get_constant_charge_current(axp20x_batt,
+							 &val->intval);
+		if (ret)
+			return ret;
+		return 0;
+
+	case POWER_SUPPLY_PROP_CURRENT_NOW:
+		/*
+		 * The offset of this value is currently unknown and is
+		 * not documented in the datasheet. Based on
+		 * observation it's assumed to be somewhere around
+		 * 450ma. I will leave the value raw for now.
+		 */
+		ret = iio_read_channel_processed(axp20x_batt->batt_chrg_i, &val->intval);
+		if (ret)
+			return ret;
+		/* IIO framework gives mA but Power Supply framework gives uA */
+		val->intval *= 1000;
+		return 0;
+
+	case POWER_SUPPLY_PROP_CAPACITY:
+		ret = regmap_read(axp20x_batt->regmap, AXP717_ON_INDICATE,
+				  &reg);
+		if (ret)
+			return ret;
+
+		if (!FIELD_GET(AXP717_PWR_OP_BATT_PRESENT, reg))
+			return -ENODEV;
+
+		ret = regmap_read(axp20x_batt->regmap,
+				  AXP717_BATT_PERCENT_DATA, &reg);
+		if (ret)
+			return ret;
+
+		/*
+		 * Fuel Gauge data takes 7 bits but the stored value seems to be
+		 * directly the raw percentage without any scaling to 7 bits.
+		 */
+		val->intval = reg & AXP209_FG_PERCENT;
+		return 0;
+
+	case POWER_SUPPLY_PROP_VOLTAGE_MAX:
+		return axp20x_batt->data->get_max_voltage(axp20x_batt,
+							  &val->intval);
+
+	case POWER_SUPPLY_PROP_VOLTAGE_MIN:
+		ret = regmap_read(axp20x_batt->regmap,
+				  AXP717_VSYS_V_POWEROFF, &reg);
+		if (ret)
+			return ret;
+
+		val->intval = AXP717_BAT_VMIN_MIN_UV + AXP717_BAT_VMIN_STEP *
+			(reg & AXP717_V_OFF_MASK);
+		return 0;
+
+	case POWER_SUPPLY_PROP_VOLTAGE_NOW:
+		ret = iio_read_channel_processed(axp20x_batt->batt_v,
+						 &val->intval);
+		if (ret)
+			return ret;
+
+		/* IIO framework gives mV but Power Supply framework gives uV */
+		val->intval *= 1000;
+		return 0;
+
+	case POWER_SUPPLY_PROP_CHARGE_TERM_CURRENT:
+		ret = regmap_read(axp20x_batt->regmap,
+				  AXP717_ITERM_CHG_SET, &reg);
+		if (ret)
+			return ret;
+
+		val->intval = (reg & AXP717_ITERM_CHG_LIM_MASK) * AXP717_ITERM_CC_STEP;
+		return 0;
+
+	default:
+		return -EINVAL;
+	}
+}
+
 static int axp22x_battery_set_max_voltage(struct axp20x_batt_ps *axp20x_batt,
 					  int val)
 {
@@ -396,6 +642,35 @@ static int axp20x_battery_set_max_voltage(struct axp20x_batt_ps *axp20x_batt,
 				  AXP20X_CHRG_CTRL1_TGT_VOLT, val);
 }
 
+static int axp717_battery_set_max_voltage(struct axp20x_batt_ps *axp20x_batt,
+					  int val)
+{
+	switch (val) {
+	case 4000000:
+		val = AXP717_CHRG_CV_4_0V;
+		break;
+
+	case 4100000:
+		val = AXP717_CHRG_CV_4_1V;
+		break;
+
+	case 4200000:
+		val = AXP717_CHRG_CV_4_2V;
+		break;
+
+	default:
+		/*
+		 * AXP717 can go up to 4.35, 4.4, and 5.0 volts which
+		 * seem too high for lithium batteries, so do not allow.
+		 */
+		return -EINVAL;
+	}
+
+	return regmap_update_bits(axp20x_batt->regmap,
+				  AXP717_CV_CHG_SET,
+				  AXP717_CHRG_CV_VOLT_MASK, val);
+}
+
 static int axp20x_set_constant_charge_current(struct axp20x_batt_ps *axp_batt,
 					      int charge_current)
 {
@@ -412,6 +687,24 @@ static int axp20x_set_constant_charge_current(struct axp20x_batt_ps *axp_batt,
 				  AXP20X_CHRG_CTRL1_TGT_CURR, charge_current);
 }
 
+static int axp717_set_constant_charge_current(struct axp20x_batt_ps *axp,
+					      int charge_current)
+{
+	int val;
+
+	if (charge_current > axp->max_ccc)
+		return -EINVAL;
+
+	if (charge_current > AXP717_BAT_CC_MAX_UA || charge_current < 0)
+		return -EINVAL;
+
+	val = (charge_current - axp->data->ccc_offset) /
+		axp->data->ccc_scale;
+
+	return regmap_update_bits(axp->regmap, AXP717_ICC_CHG_SET,
+				  AXP717_ICC_CHARGER_LIM_MASK, val);
+}
+
 static int axp20x_set_max_constant_charge_current(struct axp20x_batt_ps *axp,
 						  int charge_current)
 {
@@ -456,6 +749,19 @@ static int axp20x_set_voltage_min_design(struct axp20x_batt_ps *axp_batt,
 				  AXP20X_V_OFF_MASK, val1);
 }
 
+static int axp717_set_voltage_min_design(struct axp20x_batt_ps *axp_batt,
+					 int min_voltage)
+{
+	int val1 = (min_voltage - AXP717_BAT_VMIN_MIN_UV) / AXP717_BAT_VMIN_STEP;
+
+	if (val1 < 0 || val1 > AXP717_V_OFF_MASK)
+		return -EINVAL;
+
+	return regmap_update_bits(axp_batt->regmap,
+				  AXP717_VSYS_V_POWEROFF,
+				  AXP717_V_OFF_MASK, val1);
+}
+
 static int axp20x_battery_set_prop(struct power_supply *psy,
 				   enum power_supply_property psp,
 				   const union power_supply_propval *val)
@@ -492,6 +798,42 @@ static int axp20x_battery_set_prop(struct power_supply *psy,
 	}
 }
 
+static int axp717_battery_set_prop(struct power_supply *psy,
+				   enum power_supply_property psp,
+				   const union power_supply_propval *val)
+{
+	struct axp20x_batt_ps *axp20x_batt = power_supply_get_drvdata(psy);
+
+	switch (psp) {
+	case POWER_SUPPLY_PROP_VOLTAGE_MIN:
+		return axp717_set_voltage_min_design(axp20x_batt, val->intval);
+
+	case POWER_SUPPLY_PROP_VOLTAGE_MAX:
+		return axp20x_batt->data->set_max_voltage(axp20x_batt, val->intval);
+
+	case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX:
+		return axp717_set_constant_charge_current(axp20x_batt,
+							  val->intval);
+	case POWER_SUPPLY_PROP_STATUS:
+		switch (val->intval) {
+		case POWER_SUPPLY_STATUS_CHARGING:
+			return regmap_update_bits(axp20x_batt->regmap,
+						  AXP717_MODULE_EN_CONTROL_2,
+						  AXP717_CHRG_ENABLE,
+						  AXP717_CHRG_ENABLE);
+
+		case POWER_SUPPLY_STATUS_DISCHARGING:
+		case POWER_SUPPLY_STATUS_NOT_CHARGING:
+			return regmap_update_bits(axp20x_batt->regmap,
+						  AXP717_MODULE_EN_CONTROL_2,
+						  AXP717_CHRG_ENABLE, 0);
+		}
+		return -EINVAL;
+	default:
+		return -EINVAL;
+	}
+}
+
 static enum power_supply_property axp20x_battery_props[] = {
 	POWER_SUPPLY_PROP_PRESENT,
 	POWER_SUPPLY_PROP_ONLINE,
@@ -506,6 +848,20 @@ static enum power_supply_property axp20x_battery_props[] = {
 	POWER_SUPPLY_PROP_CAPACITY,
 };
 
+static enum power_supply_property axp717_battery_props[] = {
+	POWER_SUPPLY_PROP_PRESENT,
+	POWER_SUPPLY_PROP_ONLINE,
+	POWER_SUPPLY_PROP_STATUS,
+	POWER_SUPPLY_PROP_VOLTAGE_NOW,
+	POWER_SUPPLY_PROP_CURRENT_NOW,
+	POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX,
+	POWER_SUPPLY_PROP_HEALTH,
+	POWER_SUPPLY_PROP_VOLTAGE_MAX,
+	POWER_SUPPLY_PROP_VOLTAGE_MIN,
+	POWER_SUPPLY_PROP_CAPACITY,
+	POWER_SUPPLY_PROP_CHARGE_TERM_CURRENT,
+};
+
 static int axp20x_battery_prop_writeable(struct power_supply *psy,
 					 enum power_supply_property psp)
 {
@@ -516,6 +872,15 @@ static int axp20x_battery_prop_writeable(struct power_supply *psy,
 	       psp == POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX;
 }
 
+static int axp717_battery_prop_writeable(struct power_supply *psy,
+					 enum power_supply_property psp)
+{
+	return psp == POWER_SUPPLY_PROP_STATUS ||
+	       psp == POWER_SUPPLY_PROP_VOLTAGE_MIN ||
+	       psp == POWER_SUPPLY_PROP_VOLTAGE_MAX ||
+	       psp == POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX;
+}
+
 static const struct power_supply_desc axp209_batt_ps_desc = {
 	.name = "axp20x-battery",
 	.type = POWER_SUPPLY_TYPE_BATTERY,
@@ -526,6 +891,16 @@ static const struct power_supply_desc axp209_batt_ps_desc = {
 	.set_property = axp20x_battery_set_prop,
 };
 
+static const struct power_supply_desc axp717_batt_ps_desc = {
+	.name = "axp20x-battery",
+	.type = POWER_SUPPLY_TYPE_BATTERY,
+	.properties = axp717_battery_props,
+	.num_properties = ARRAY_SIZE(axp717_battery_props),
+	.property_is_writeable = axp717_battery_prop_writeable,
+	.get_property = axp717_battery_get_prop,
+	.set_property = axp717_battery_set_prop,
+};
+
 static int axp209_bat_cfg_iio_channels(struct platform_device *pdev,
 				       struct axp20x_batt_ps *axp_batt)
 {
@@ -555,6 +930,27 @@ static int axp209_bat_cfg_iio_channels(struct platform_device *pdev,
 	return 0;
 }
 
+static int axp717_bat_cfg_iio_channels(struct platform_device *pdev,
+				       struct axp20x_batt_ps *axp_batt)
+{
+	axp_batt->batt_v = devm_iio_channel_get(&pdev->dev, "batt_v");
+	if (IS_ERR(axp_batt->batt_v)) {
+		if (PTR_ERR(axp_batt->batt_v) == -ENODEV)
+			return -EPROBE_DEFER;
+		return PTR_ERR(axp_batt->batt_v);
+	}
+
+	axp_batt->batt_chrg_i = devm_iio_channel_get(&pdev->dev,
+							"batt_chrg_i");
+	if (IS_ERR(axp_batt->batt_chrg_i)) {
+		if (PTR_ERR(axp_batt->batt_chrg_i) == -ENODEV)
+			return -EPROBE_DEFER;
+		return PTR_ERR(axp_batt->batt_chrg_i);
+	}
+
+	return 0;
+}
+
 static void axp209_set_battery_info(struct platform_device *pdev,
 				    struct axp20x_batt_ps *axp_batt,
 				    struct power_supply_battery_info *info)
@@ -578,6 +974,32 @@ static void axp209_set_battery_info(struct platform_device *pdev,
 	}
 }
 
+static void axp717_set_battery_info(struct platform_device *pdev,
+				    struct axp20x_batt_ps *axp_batt,
+				    struct power_supply_battery_info *info)
+{
+	int vmin = info->voltage_min_design_uv;
+	int vmax = info->voltage_max_design_uv;
+	int ccc = info->constant_charge_current_max_ua;
+	int val;
+
+	if (vmin > 0 && axp717_set_voltage_min_design(axp_batt, vmin))
+		dev_err(&pdev->dev,
+			"couldn't set voltage_min_design\n");
+
+	if (vmax > 0 && axp717_battery_set_max_voltage(axp_batt, vmax))
+		dev_err(&pdev->dev,
+			"couldn't set voltage_max_design\n");
+
+	axp717_get_constant_charge_current(axp_batt, &val);
+	axp_batt->max_ccc = ccc;
+	if (ccc <= 0 || axp717_set_constant_charge_current(axp_batt, ccc)) {
+		dev_err(&pdev->dev,
+			"couldn't set ccc from DT: current ccc is %d\n",
+			val);
+	}
+}
+
 static const struct axp_data axp209_data = {
 	.ccc_scale = 100000,
 	.ccc_offset = 300000,
@@ -603,6 +1025,18 @@ static const struct axp_data axp221_data = {
 	.set_bat_info = axp209_set_battery_info,
 };
 
+static const struct axp_data axp717_data = {
+	.ccc_scale = 64000,
+	.ccc_offset = 0,
+	.ccc_reg = AXP717_ICC_CHG_SET,
+	.ccc_mask = AXP717_ICC_CHARGER_LIM_MASK,
+	.bat_ps_desc = &axp717_batt_ps_desc,
+	.get_max_voltage = axp717_battery_get_max_voltage,
+	.set_max_voltage = axp717_battery_set_max_voltage,
+	.cfg_iio_chan = axp717_bat_cfg_iio_channels,
+	.set_bat_info = axp717_set_battery_info,
+};
+
 static const struct axp_data axp813_data = {
 	.ccc_scale = 200000,
 	.ccc_offset = 200000,
@@ -623,6 +1057,9 @@ static const struct of_device_id axp20x_battery_ps_id[] = {
 	}, {
 		.compatible = "x-powers,axp221-battery-power-supply",
 		.data = (void *)&axp221_data,
+	}, {
+		.compatible = "x-powers,axp717-battery-power-supply",
+		.data = (void *)&axp717_data,
 	}, {
 		.compatible = "x-powers,axp813-battery-power-supply",
 		.data = (void *)&axp813_data,
-- 
2.34.1

Re: [PATCH V3 14/15] power: supply: axp20x_battery: add support for AXP717

[kernel test robot]

Hi Chris,

kernel test robot noticed the following build errors:

[auto build test ERROR on sre-power-supply/for-next]
[also build test ERROR on jic23-iio/togreg lee-mfd/for-mfd-next linus/master v6.11-rc4 next-20240819]
[cannot apply to lee-mfd/for-mfd-fixes]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch#_base_tree_information]

url:    https://github.com/intel-lab-lkp/linux/commits/Chris-Morgan/iio-adc-axp20x_adc-Add-adc_en1-and-adc_en1-to-axp_data/20240820-005144
base:   https://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply.git for-next
patch link:    https://lore.kernel.org/r/20240819164619.556309-15-macroalpha82%40gmail.com
patch subject: [PATCH V3 14/15] power: supply: axp20x_battery: add support for AXP717
config: i386-buildonly-randconfig-005-20240820 (https://download.01.org/0day-ci/archive/20240820/202408201228.Hee4eSYl-lkp@intel.com/config)
compiler: clang version 18.1.5 (https://github.com/llvm/llvm-project 617a15a9eac96088ae5e9134248d8236e34b91b1)
reproduce (this is a W=1 build): (https://download.01.org/0day-ci/archive/20240820/202408201228.Hee4eSYl-lkp@intel.com/reproduce)

If you fix the issue in a separate patch/commit (i.e. not just a new version of
the same patch/commit), kindly add following tags
| Reported-by: kernel test robot <lkp@intel.com>
| Closes: https://lore.kernel.org/oe-kbuild-all/202408201228.Hee4eSYl-lkp@intel.com/

All errors (new ones prefixed by >>):

>> drivers/power/supply/axp20x_battery.c:266:9: error: call to undeclared function 'FIELD_GET'; ISO C99 and later do not support implicit function declarations [-Wimplicit-function-declaration]
     266 |         *val = FIELD_GET(AXP717_ICC_CHARGER_LIM_MASK, *val) *
         |                ^
   drivers/power/supply/axp20x_battery.c:439:17: error: call to undeclared function 'FIELD_GET'; ISO C99 and later do not support implicit function declarations [-Wimplicit-function-declaration]
     439 |                 val->intval = FIELD_GET(AXP717_PWR_OP_BATT_PRESENT, reg);
         |                               ^
   2 errors generated.


vim +/FIELD_GET +266 drivers/power/supply/axp20x_battery.c

   256	
   257	static int axp717_get_constant_charge_current(struct axp20x_batt_ps *axp,
   258						      int *val)
   259	{
   260		int ret;
   261	
   262		ret = regmap_read(axp->regmap, AXP717_ICC_CHG_SET, val);
   263		if (ret)
   264			return ret;
   265	
 > 266		*val = FIELD_GET(AXP717_ICC_CHARGER_LIM_MASK, *val) *
   267			axp->data->ccc_scale;
   268	
   269		return 0;
   270	}
   271	

-- 
0-DAY CI Kernel Test Service
https://github.com/intel/lkp-tests/wiki

Re: [PATCH V3 14/15] power: supply: axp20x_battery: add support for AXP717

[kernel test robot]

Hi Chris,

kernel test robot noticed the following build errors:

[auto build test ERROR on sre-power-supply/for-next]
[also build test ERROR on jic23-iio/togreg lee-mfd/for-mfd-next linus/master v6.11-rc4 next-20240819]
[cannot apply to lee-mfd/for-mfd-fixes]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch#_base_tree_information]

url:    https://github.com/intel-lab-lkp/linux/commits/Chris-Morgan/iio-adc-axp20x_adc-Add-adc_en1-and-adc_en1-to-axp_data/20240820-005144
base:   https://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply.git for-next
patch link:    https://lore.kernel.org/r/20240819164619.556309-15-macroalpha82%40gmail.com
patch subject: [PATCH V3 14/15] power: supply: axp20x_battery: add support for AXP717
config: arc-randconfig-001-20240820 (https://download.01.org/0day-ci/archive/20240820/202408201232.lgLOd5Nu-lkp@intel.com/config)
compiler: arceb-elf-gcc (GCC) 13.2.0
reproduce (this is a W=1 build): (https://download.01.org/0day-ci/archive/20240820/202408201232.lgLOd5Nu-lkp@intel.com/reproduce)

If you fix the issue in a separate patch/commit (i.e. not just a new version of
the same patch/commit), kindly add following tags
| Reported-by: kernel test robot <lkp@intel.com>
| Closes: https://lore.kernel.org/oe-kbuild-all/202408201232.lgLOd5Nu-lkp@intel.com/

All errors (new ones prefixed by >>):

   drivers/power/supply/axp20x_battery.c: In function 'axp717_get_constant_charge_current':
>> drivers/power/supply/axp20x_battery.c:266:16: error: implicit declaration of function 'FIELD_GET' [-Werror=implicit-function-declaration]
     266 |         *val = FIELD_GET(AXP717_ICC_CHARGER_LIM_MASK, *val) *
         |                ^~~~~~~~~
   cc1: some warnings being treated as errors


vim +/FIELD_GET +266 drivers/power/supply/axp20x_battery.c

   256	
   257	static int axp717_get_constant_charge_current(struct axp20x_batt_ps *axp,
   258						      int *val)
   259	{
   260		int ret;
   261	
   262		ret = regmap_read(axp->regmap, AXP717_ICC_CHG_SET, val);
   263		if (ret)
   264			return ret;
   265	
 > 266		*val = FIELD_GET(AXP717_ICC_CHARGER_LIM_MASK, *val) *
   267			axp->data->ccc_scale;
   268	
   269		return 0;
   270	}
   271	

-- 
0-DAY CI Kernel Test Service
https://github.com/intel/lkp-tests/wiki

Re: [PATCH V3 14/15] power: supply: axp20x_battery: add support for AXP717

[Chris Morgan]

On Tue, Aug 20, 2024 at 01:37:02PM +0800, kernel test robot wrote:
> Hi Chris,
> 
> kernel test robot noticed the following build errors:
> 
> [auto build test ERROR on sre-power-supply/for-next]
> [also build test ERROR on jic23-iio/togreg lee-mfd/for-mfd-next linus/master v6.11-rc4 next-20240819]
> [cannot apply to lee-mfd/for-mfd-fixes]
> [If your patch is applied to the wrong git tree, kindly drop us a note.
> And when submitting patch, we suggest to use '--base' as documented in
> https://git-scm.com/docs/git-format-patch#_base_tree_information]
> 
> url:    https://github.com/intel-lab-lkp/linux/commits/Chris-Morgan/iio-adc-axp20x_adc-Add-adc_en1-and-adc_en1-to-axp_data/20240820-005144
> base:   https://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply.git for-next
> patch link:    https://lore.kernel.org/r/20240819164619.556309-15-macroalpha82%40gmail.com
> patch subject: [PATCH V3 14/15] power: supply: axp20x_battery: add support for AXP717
> config: arc-randconfig-001-20240820 (https://download.01.org/0day-ci/archive/20240820/202408201232.lgLOd5Nu-lkp@intel.com/config)
> compiler: arceb-elf-gcc (GCC) 13.2.0
> reproduce (this is a W=1 build): (https://download.01.org/0day-ci/archive/20240820/202408201232.lgLOd5Nu-lkp@intel.com/reproduce)
> 
> If you fix the issue in a separate patch/commit (i.e. not just a new version of
> the same patch/commit), kindly add following tags
> | Reported-by: kernel test robot <lkp@intel.com>
> | Closes: https://lore.kernel.org/oe-kbuild-all/202408201232.lgLOd5Nu-lkp@intel.com/

Acknowledged. It looks like I need to explicitly include
<linux/bitfield.h>. I'll include that in the next revision.

Thank you,
Chris

> 
> All errors (new ones prefixed by >>):
> 
>    drivers/power/supply/axp20x_battery.c: In function 'axp717_get_constant_charge_current':
> >> drivers/power/supply/axp20x_battery.c:266:16: error: implicit declaration of function 'FIELD_GET' [-Werror=implicit-function-declaration]
>      266 |         *val = FIELD_GET(AXP717_ICC_CHARGER_LIM_MASK, *val) *
>          |                ^~~~~~~~~
>    cc1: some warnings being treated as errors
> 
> 
> vim +/FIELD_GET +266 drivers/power/supply/axp20x_battery.c
> 
>    256	
>    257	static int axp717_get_constant_charge_current(struct axp20x_batt_ps *axp,
>    258						      int *val)
>    259	{
>    260		int ret;
>    261	
>    262		ret = regmap_read(axp->regmap, AXP717_ICC_CHG_SET, val);
>    263		if (ret)
>    264			return ret;
>    265	
>  > 266		*val = FIELD_GET(AXP717_ICC_CHARGER_LIM_MASK, *val) *
>    267			axp->data->ccc_scale;
>    268	
>    269		return 0;
>    270	}
>    271	
> 
> -- 
> 0-DAY CI Kernel Test Service
> https://github.com/intel/lkp-tests/wiki

[PATCH V3 15/15] arm64: dts: allwinner: h700: Add charger for Anbernic RG35XX

[Chris Morgan]

From: Chris Morgan <macromorgan@hotmail.com>

Add the necessary nodes for the AXP717 to allow for monitoring the USB
and battery charger.

Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
---
 .../sun50i-h700-anbernic-rg35xx-2024.dts      | 21 +++++++++++++++++++
 1 file changed, 21 insertions(+)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h700-anbernic-rg35xx-2024.dts b/arch/arm64/boot/dts/allwinner/sun50i-h700-anbernic-rg35xx-2024.dts
index 078b9ea3d9d0..18b63efae083 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h700-anbernic-rg35xx-2024.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h700-anbernic-rg35xx-2024.dts
@@ -21,6 +21,12 @@ aliases {
 		serial0 = &uart0;
 	};
 
+	battery: battery {
+		compatible = "simple-battery";
+		constant-charge-current-max-microamp = <1024000>;
+		voltage-max-design-microvolt = <4200000>;
+	};
+
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
@@ -217,6 +223,16 @@ axp717: pmic@34 {
 		vin3-supply = <&reg_vcc5v>;
 		vin4-supply = <&reg_vcc5v>;
 
+		axp_adc: adc {
+			compatible = "x-powers,axp717-adc";
+			#io-channel-cells = <1>;
+		};
+
+		battery_power: battery-power {
+			compatible = "x-powers,axp717-battery-power-supply";
+			monitored-battery = <&battery>;
+		};
+
 		regulators {
 			reg_dcdc1: dcdc1 {
 				regulator-always-on;
@@ -307,6 +323,11 @@ reg_cpusldo: cpusldo {
 				/* unused */
 			};
 		};
+
+		usb_power: usb-power {
+			compatible = "x-powers,axp717-usb-power-supply";
+			input-current-limit-microamp = <1500000>;
+		};
 	};
 };
 
-- 
2.34.1