From: Nishanth Menon <nm@ti.com>
To: Manorit Chawdhry <m-chawdhry@ti.com>
Cc: Vignesh Raghavendra <vigneshr@ti.com>,
Tero Kristo <kristo@kernel.org>, Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
Neha Malcom Francis <n-francis@ti.com>,
Aniket Limaye <a-limaye@ti.com>, Udit Kumar <u-kumar1@ti.com>,
Beleswar Padhi <b-padhi@ti.com>,
Siddharth Vadapalli <s-vadapalli@ti.com>,
Andrew Davis <afd@ti.com>
Subject: Re: [PATCH v4 1/5] arm64: dts: ti: k3-j721s2*: Add bootph-* properties
Date: Sat, 24 Aug 2024 12:50:26 -0500 [thread overview]
Message-ID: <20240824175026.irbm76wgvntdrjm7@footboard> (raw)
In-Reply-To: <20240814-b4-upstream-bootph-all-v4-1-f2b462000f25@ti.com>
On 13:17-20240814, Manorit Chawdhry wrote:
> Adds bootph-* properties to the leaf nodes to enable bootloaders to
> utilise them.
>
> Reviewed-by: Andrew Davis <afd@ti.com>
> Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
> ---
> arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts | 14 ++++++++++++++
> arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi | 4 +++-
> arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi | 17 +++++++++++++++--
> arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi | 2 ++
> 4 files changed, 34 insertions(+), 3 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
> index c5a0b7cbb14f..3b5f8f08cf32 100644
> --- a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
> +++ b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
> @@ -138,6 +138,7 @@ J721S2_IOPAD(0x044, PIN_OUTPUT, 14) /* (Y26) MCASP0_AXR1.UART8_RTSn */
> J721S2_IOPAD(0x0d0, PIN_INPUT, 11) /* (AF26) SPI0_CS1.UART8_RXD */
> J721S2_IOPAD(0x0d4, PIN_OUTPUT, 11) /* (AH27) SPI0_CLK.UART8_TXD */
> >;
> + bootph-all;
> };
>
> main_i2c3_pins_default: main-i2c3-default-pins {
> @@ -165,6 +166,7 @@ J721S2_IOPAD(0x0f4, PIN_INPUT, 0) /* (R24) MMC1_DAT2 */
> J721S2_IOPAD(0x0f0, PIN_INPUT, 0) /* (R22) MMC1_DAT3 */
> J721S2_IOPAD(0x0e8, PIN_INPUT, 8) /* (AE25) TIMER_IO0.MMC1_SDCD */
> >;
> + bootph-all;
> };
>
> vdd_sd_dv_pins_default: vdd-sd-dv-default-pins {
> @@ -177,6 +179,7 @@ main_usbss0_pins_default: main-usbss0-default-pins {
> pinctrl-single,pins = <
> J721S2_IOPAD(0x0ec, PIN_OUTPUT, 6) /* (AG25) TIMER_IO1.USB0_DRVVBUS */
> >;
> + bootph-all;
> };
>
> main_mcan3_pins_default: main-mcan3-default-pins {
> @@ -200,6 +203,7 @@ wkup_uart0_pins_default: wkup-uart0-default-pins {
> J721S2_WKUP_IOPAD(0x048, PIN_INPUT, 0) /* (D28) WKUP_UART0_RXD */
> J721S2_WKUP_IOPAD(0x04c, PIN_OUTPUT, 0) /* (D27) WKUP_UART0_TXD */
> >;
> + bootph-all;
> };
>
> mcu_uart0_pins_default: mcu-uart0-default-pins {
> @@ -209,6 +213,7 @@ J721S2_WKUP_IOPAD(0x094, PIN_OUTPUT, 0) /* (D25) WKUP_GPIO0_15.MCU_UART0_RTSn */
> J721S2_WKUP_IOPAD(0x08c, PIN_INPUT, 0) /* (C24) WKUP_GPIO0_13.MCU_UART0_RXD */
> J721S2_WKUP_IOPAD(0x088, PIN_OUTPUT, 0) /* (C25) WKUP_GPIO0_12.MCU_UART0_TXD */
> >;
> + bootph-all;
> };
>
> mcu_cpsw_pins_default: mcu-cpsw-default-pins {
> @@ -301,6 +306,7 @@ J721S2_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (A20) MCU_OSPI1_D3 */
> J721S2_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (B19) MCU_OSPI1_DQS */
> J721S2_WKUP_IOPAD(0x00c, PIN_INPUT, 0) /* (B20) MCU_OSPI1_LBCLKO */
> >;
> + bootph-all;
> };
> };
>
> @@ -316,12 +322,14 @@ &wkup_uart0 {
> status = "reserved";
> pinctrl-names = "default";
> pinctrl-0 = <&wkup_uart0_pins_default>;
> + bootph-all;
> };
>
> &mcu_uart0 {
> status = "okay";
> pinctrl-names = "default";
> pinctrl-0 = <&mcu_uart0_pins_default>;
> + bootph-all;
> };
>
> &main_uart8 {
> @@ -330,6 +338,7 @@ &main_uart8 {
> pinctrl-0 = <&main_uart8_pins_default>;
> /* Shared with TFA on this platform */
> power-domains = <&k3_pds 357 TI_SCI_PD_SHARED>;
> + bootph-all;
> };
>
> &main_i2c0 {
> @@ -385,6 +394,7 @@ &main_sdhci0 {
> non-removable;
> ti,driver-strength-ohm = <50>;
> disable-wp;
> + bootph-all;
> };
>
> &main_sdhci1 {
> @@ -395,6 +405,7 @@ &main_sdhci1 {
> disable-wp;
> vmmc-supply = <&vdd_mmc1>;
> vqmmc-supply = <&vdd_sd_dv>;
> + bootph-all;
> };
>
> &mcu_cpsw {
> @@ -444,6 +455,7 @@ &usbss0 {
> status = "okay";
> pinctrl-0 = <&main_usbss0_pins_default>;
> pinctrl-names = "default";
> + bootph-all;
> ti,vbus-divider;
> ti,usb2-only;
> };
> @@ -451,6 +463,7 @@ &usbss0 {
> &usb0 {
> dr_mode = "otg";
> maximum-speed = "high-speed";
> + bootph-all;
> };
>
> &ospi1 {
> @@ -464,6 +477,7 @@ flash@0 {
> spi-tx-bus-width = <1>;
> spi-rx-bus-width = <4>;
> spi-max-frequency = <40000000>;
> + bootph-all;
> cdns,tshsl-ns = <60>;
> cdns,tsd2d-ns = <60>;
> cdns,tchsh-ns = <60>;
> diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
> index 9ed6949b40e9..0d72dd0b5033 100644
> --- a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
> @@ -816,6 +816,7 @@ secure_proxy_main: mailbox@32c00000 {
> <0x00 0x32800000 0x00 0x100000>;
> interrupt-names = "rx_011";
> interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
> + bootph-all;
> };
>
> hwspinlock: spinlock@30e00000 {
> @@ -1225,6 +1226,7 @@ usb0: usb@6000000 {
> interrupt-names = "host", "peripheral", "otg";
> maximum-speed = "super-speed";
> dr_mode = "otg";
> + bootph-all;
I think you should split the SoC changes from the board changes. it
needs clear explanation why all boards need a change like this.
> };
> };
>
> @@ -1944,8 +1946,8 @@ c71_1: dsp@65800000 {
> main_esm: esm@700000 {
> compatible = "ti,j721e-esm";
> reg = <0x00 0x700000 0x00 0x1000>;
> - ti,esm-pins = <688>, <689>;
> bootph-pre-ram;
> + ti,esm-pins = <688>, <689>;
> };
>
> watchdog0: watchdog@2200000 {
> diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
> index 8feb42c89e47..05a5e35fddcd 100644
> --- a/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
> @@ -21,16 +21,19 @@ sms: system-controller@44083000 {
> k3_pds: power-controller {
> compatible = "ti,sci-pm-domain";
> #power-domain-cells = <2>;
> + bootph-all;
> };
>
> k3_clks: clock-controller {
> compatible = "ti,k2g-sci-clk";
> #clock-cells = <2>;
> + bootph-all;
> };
>
> k3_reset: reset-controller {
> compatible = "ti,sci-reset";
> #reset-cells = <2>;
> + bootph-all;
> };
> };
>
> @@ -43,6 +46,7 @@ wkup_conf: bus@43000000 {
> chipid: chipid@14 {
> compatible = "ti,am654-chipid";
> reg = <0x14 0x4>;
> + bootph-all;
> };
> };
>
> @@ -53,6 +57,8 @@ secure_proxy_sa3: mailbox@43600000 {
> reg = <0x00 0x43600000 0x00 0x10000>,
> <0x00 0x44880000 0x00 0x20000>,
> <0x00 0x44860000 0x00 0x20000>;
> + bootph-pre-ram;
> +
> /*
> * Marked Disabled:
> * Node is incomplete as it is meant for bootloaders and
> @@ -167,6 +173,7 @@ mcu_timer0: timer@40400000 {
> assigned-clocks = <&k3_clks 35 1>;
> assigned-clock-parents = <&k3_clks 35 2>;
> power-domains = <&k3_pds 35 TI_SCI_PD_EXCLUSIVE>;
> + bootph-pre-ram;
> ti,timer-pwm;
> /* Non-MPU Firmware usage */
> status = "reserved";
> @@ -361,6 +368,7 @@ wkup_i2c0: i2c@42120000 {
> clocks = <&k3_clks 223 1>;
> clock-names = "fck";
> power-domains = <&k3_pds 223 TI_SCI_PD_EXCLUSIVE>;
> + bootph-all;
> status = "disabled";
> };
>
> @@ -469,6 +477,7 @@ mcu_ringacc: ringacc@2b800000 {
> <0x0 0x2a500000 0x0 0x40000>,
> <0x0 0x28440000 0x0 0x40000>;
> reg-names = "rt", "fifos", "proxy_gcfg", "proxy_target", "cfg";
> + bootph-all;
> ti,num-rings = <286>;
> ti,sci-rm-range-gp-rings = <0x1>;
> ti,sci = <&sms>;
> @@ -488,6 +497,7 @@ mcu_udmap: dma-controller@285c0000 {
> "tchan", "rchan", "rflow";
> msi-parent = <&main_udmass_inta>;
> #dma-cells = <1>;
> + bootph-all;
>
> ti,sci = <&sms>;
> ti,sci-dev-id = <273>;
> @@ -507,6 +517,8 @@ secure_proxy_mcu: mailbox@2a480000 {
> reg = <0x00 0x2a480000 0x00 0x80000>,
> <0x00 0x2a380000 0x00 0x80000>,
> <0x00 0x2a400000 0x00 0x80000>;
> + bootph-pre-ram;
> +
> /*
> * Marked Disabled:
> * Node is incomplete as it is meant for bootloaders and
> @@ -667,6 +679,7 @@ wkup_vtm0: temperature-sensor@42040000 {
> <0x00 0x42050000 0x0 0x350>;
> power-domains = <&k3_pds 180 TI_SCI_PD_SHARED>;
> #thermal-sensor-cells = <1>;
> + bootph-pre-ram;
> };
>
> mcu_r5fss0: r5fss@41000000 {
> @@ -712,15 +725,15 @@ mcu_r5fss0_core1: r5f@41400000 {
> mcu_esm: esm@40800000 {
> compatible = "ti,j721e-esm";
> reg = <0x00 0x40800000 0x00 0x1000>;
> - ti,esm-pins = <95>;
> bootph-pre-ram;
> + ti,esm-pins = <95>;
Drop - there is nothing you need to do here.
> };
>
> wkup_esm: esm@42080000 {
> compatible = "ti,j721e-esm";
> reg = <0x00 0x42080000 0x00 0x1000>;
> - ti,esm-pins = <63>;
> bootph-pre-ram;
> + ti,esm-pins = <63>;
Why?
> };
>
> /*
> diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
> index 36136db26a47..c333148f2789 100644
> --- a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
> @@ -170,6 +170,7 @@ J721S2_WKUP_IOPAD(0x028, PIN_INPUT, 0) /* (F20) MCU_OSPI0_D7 */
> J721S2_WKUP_IOPAD(0x008, PIN_INPUT, 0) /* (E18) MCU_OSPI0_DQS */
> J721S2_WKUP_IOPAD(0x004, PIN_INPUT, 0) /* (E20) MCU_OSPI0_LBCLKO */
> >;
> + bootph-all;
> };
> };
>
> @@ -440,6 +441,7 @@ flash@0 {
> spi-tx-bus-width = <8>;
> spi-rx-bus-width = <8>;
> spi-max-frequency = <25000000>;
> + bootph-all;
> cdns,tshsl-ns = <60>;
> cdns,tsd2d-ns = <60>;
> cdns,tchsh-ns = <60>;
>
> --
> 2.46.0
>
--
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
next prev parent reply other threads:[~2024-08-24 17:50 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-08-14 7:47 [PATCH v4 0/5] Add bootph-all property for J7 boards Manorit Chawdhry
2024-08-14 7:47 ` [PATCH v4 1/5] arm64: dts: ti: k3-j721s2*: Add bootph-* properties Manorit Chawdhry
2024-08-24 17:50 ` Nishanth Menon [this message]
2024-08-14 7:47 ` [PATCH v4 2/5] arm64: dts: ti: k3-j784s4*: Remove bootph properties from parent nodes Manorit Chawdhry
2024-08-24 17:52 ` Nishanth Menon
2024-08-14 7:47 ` [PATCH v4 3/5] arm64: dts: ti: k3-am68*: Add bootph-* properties Manorit Chawdhry
2024-08-21 10:34 ` Kumar, Udit
2024-08-14 7:47 ` [PATCH v4 4/5] arm64: dts: ti: k3-j721e*: " Manorit Chawdhry
2024-08-14 7:47 ` [PATCH v4 5/5] arm64: dts: ti: k3-j7200*: " Manorit Chawdhry
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20240824175026.irbm76wgvntdrjm7@footboard \
--to=nm@ti.com \
--cc=a-limaye@ti.com \
--cc=afd@ti.com \
--cc=b-padhi@ti.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=kristo@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=m-chawdhry@ti.com \
--cc=n-francis@ti.com \
--cc=robh@kernel.org \
--cc=s-vadapalli@ti.com \
--cc=u-kumar1@ti.com \
--cc=vigneshr@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox