[PATCH v2 03/10] dt-bindings: iio: adc: ad7606: Add iio backend bindings

[Guillaume Stols <gstols@baylibre.com>]

Add the required properties for iio-backend support, as well as an
example and the conditions to mutually exclude interruption and
conversion trigger with iio-backend.
The iio-backend's function is to controls the communication, and thus the
interruption pin won't be available anymore.
As a consequence, the conversion pin must be controlled externally since
we will miss information about when every single conversion cycle (i.e
conversion + data transfer) ends, hence a PWM is introduced to trigger
the conversions.

Signed-off-by: Guillaume Stols <gstols@baylibre.com>
---
 .../devicetree/bindings/iio/adc/adi,ad7606.yaml    | 76 +++++++++++++++++++++-
 1 file changed, 74 insertions(+), 2 deletions(-)

diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml
index 12995ebcddc2..74a8680904b1 100644
--- a/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml
+++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml
@@ -118,13 +118,32 @@ properties:
       this property must be defined.
     type: boolean
 
+  pwms:
+    description:
+      In case the conversion is triggered by a PWM instead of a GPIO plugged to
+      the CONVST pin, the PWM must be referenced.
+    minItems: 1
+    maxItems: 2
+
+  pwm-names:
+    description:
+      The name of each PWM, the first is connected to CONVST, and the second is
+      connected to CONVST2 if CONVST2 is available and not connected to CONVST1.
+    minItems: 1
+    maxItems: 2
+
+  io-backends:
+    description:
+      A reference to the iio-backend, which is responsible handling the BUSY
+      pin's falling edge and communication.
+      An example of backend can be found at
+      http://analogdevicesinc.github.io/hdl/library/axi_ad7606x/index.html
+
 required:
   - compatible
   - reg
   - avcc-supply
   - vdrive-supply
-  - interrupts
-  - adi,conversion-start-gpios
 
 oneOf:
   - required:
@@ -138,6 +157,34 @@ oneOf:
           - spi-cpol
 
 allOf:
+  - if:
+      properties:
+        pwms: false
+    then:
+      required:
+        - adi,conversion-start-gpios
+
+  - if:
+      properties:
+        adi,conversion-start-gpios: false
+    then:
+      required:
+        - pwms
+
+  - if:
+      properties:
+        interrupts: false
+    then:
+      required:
+        - io-backends
+
+  - if:
+      properties:
+        io-backends: false
+    then:
+      required:
+        - interrupts
+
   - if:
       properties:
         compatible:
@@ -179,12 +226,37 @@ allOf:
         adi,sw-mode: false
     else:
       properties:
+        pwms:
+          maxItems: 1
+        pwm-names:
+          maxItems: 1
         adi,conversion-start-gpios:
           maxItems: 1
 
 unevaluatedProperties: false
 
 examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    / {
+        adi_adc {
+            compatible = "adi,ad7606b";
+            parallel-interface;
+            pwms = <&axi_pwm_gen 0 0>;
+
+            avcc-supply = <&adc_vref>;
+            vdrive-supply = <&vdd_supply>;
+
+            reset-gpios = <&gpio0 91 GPIO_ACTIVE_HIGH>;
+            standby-gpios = <&gpio0 90 GPIO_ACTIVE_LOW>;
+            adi,range-gpios = <&gpio0 89 GPIO_ACTIVE_HIGH>;
+            adi,oversampling-ratio-gpios = <&gpio0 88 GPIO_ACTIVE_HIGH
+                                            &gpio0 87 GPIO_ACTIVE_HIGH
+                                            &gpio0 86 GPIO_ACTIVE_HIGH>;
+            io-backends = <&iio_backend>;
+        };
+    };
+
   - |
     #include <dt-bindings/gpio/gpio.h>
     #include <dt-bindings/interrupt-controller/irq.h>

-- 
2.34.1