From: Andrei Simion <andrei.simion@microchip.com>
To: <nicolas.ferre@microchip.com>, <claudiu.beznea@tuxon.dev>,
<alexandre.belloni@bootlin.com>, <robh@kernel.org>,
<krzk+dt@kernel.org>, <conor+dt@kernel.org>
Cc: <linux-arm-kernel@lists.infradead.org>,
<linux-kernel@vger.kernel.org>, <devicetree@vger.kernel.org>,
Andrei Simion <andrei.simion@microchip.com>,
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Subject: [PATCH v2 3/4] ARM: dts: microchip: Rename LED sub nodes name
Date: Tue, 1 Oct 2024 18:25:40 +0300 [thread overview]
Message-ID: <20241001152541.91945-4-andrei.simion@microchip.com> (raw)
In-Reply-To: <20241001152541.91945-1-andrei.simion@microchip.com>
dtbs_check warnings:
leds: 'd[0-9]', 'ds[0-9]' do not match any of the regexes :
'(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
leds: 'red', 'green', 'blue' do not match any of regexes :
'(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
Rename the led sub nodes according to devicetree specification and
leds-gpio.yaml
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Andrei Simion <andrei.simion@microchip.com>
---
v1 -> v2:
- add acked-by
- use pattern led-<old-label> when rename sub nodes
- rewrap commit message
---
arch/arm/boot/dts/microchip/aks-cdu.dts | 8 ++++----
arch/arm/boot/dts/microchip/animeo_ip.dts | 8 ++++----
arch/arm/boot/dts/microchip/at91-sam9x60ek.dts | 6 +++---
arch/arm/boot/dts/microchip/at91rm9200ek.dts | 6 +++---
arch/arm/boot/dts/microchip/at91sam9260ek.dts | 4 ++--
arch/arm/boot/dts/microchip/at91sam9261ek.dts | 6 +++---
arch/arm/boot/dts/microchip/at91sam9263ek.dts | 4 ++--
arch/arm/boot/dts/microchip/at91sam9g20ek.dts | 4 ++--
8 files changed, 23 insertions(+), 23 deletions(-)
diff --git a/arch/arm/boot/dts/microchip/aks-cdu.dts b/arch/arm/boot/dts/microchip/aks-cdu.dts
index 742fcf525e1b..0c3373ad1723 100644
--- a/arch/arm/boot/dts/microchip/aks-cdu.dts
+++ b/arch/arm/boot/dts/microchip/aks-cdu.dts
@@ -98,23 +98,23 @@ rootfs@500000 {
leds {
compatible = "gpio-leds";
- red {
+ led-red {
gpios = <&pioC 10 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "none";
};
- green {
+ led-green {
gpios = <&pioA 5 GPIO_ACTIVE_LOW>;
linux,default-trigger = "none";
default-state = "on";
};
- yellow {
+ led-yellow {
gpios = <&pioB 20 GPIO_ACTIVE_LOW>;
linux,default-trigger = "none";
};
- blue {
+ led-blue {
gpios = <&pioB 21 GPIO_ACTIVE_LOW>;
linux,default-trigger = "none";
};
diff --git a/arch/arm/boot/dts/microchip/animeo_ip.dts b/arch/arm/boot/dts/microchip/animeo_ip.dts
index 29936bfbeeb7..7f527622d3f2 100644
--- a/arch/arm/boot/dts/microchip/animeo_ip.dts
+++ b/arch/arm/boot/dts/microchip/animeo_ip.dts
@@ -146,23 +146,23 @@ usb0: ohci@500000 {
leds {
compatible = "gpio-leds";
- power_green {
+ led-power-green {
label = "power_green";
gpios = <&pioC 17 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
};
- power_red {
+ led-power-red {
label = "power_red";
gpios = <&pioA 2 GPIO_ACTIVE_HIGH>;
};
- tx_green {
+ led-tx-green {
label = "tx_green";
gpios = <&pioC 19 GPIO_ACTIVE_HIGH>;
};
- tx_red {
+ led-tx-red {
label = "tx_red";
gpios = <&pioC 18 GPIO_ACTIVE_HIGH>;
};
diff --git a/arch/arm/boot/dts/microchip/at91-sam9x60ek.dts b/arch/arm/boot/dts/microchip/at91-sam9x60ek.dts
index 3b38707d736e..c416cbe99580 100644
--- a/arch/arm/boot/dts/microchip/at91-sam9x60ek.dts
+++ b/arch/arm/boot/dts/microchip/at91-sam9x60ek.dts
@@ -53,17 +53,17 @@ leds {
pinctrl-0 = <&pinctrl_gpio_leds>;
status = "okay"; /* Conflict with pwm0. */
- red {
+ led-red {
label = "red";
gpios = <&pioB 11 GPIO_ACTIVE_HIGH>;
};
- green {
+ led-green {
label = "green";
gpios = <&pioB 12 GPIO_ACTIVE_HIGH>;
};
- blue {
+ led-blue {
label = "blue";
gpios = <&pioB 13 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
diff --git a/arch/arm/boot/dts/microchip/at91rm9200ek.dts b/arch/arm/boot/dts/microchip/at91rm9200ek.dts
index 4624a6f076f8..0bf472b157a5 100644
--- a/arch/arm/boot/dts/microchip/at91rm9200ek.dts
+++ b/arch/arm/boot/dts/microchip/at91rm9200ek.dts
@@ -127,19 +127,19 @@ root@350000 {
leds {
compatible = "gpio-leds";
- ds2 {
+ led-ds2 {
label = "green";
gpios = <&pioB 0 GPIO_ACTIVE_LOW>;
linux,default-trigger = "mmc0";
};
- ds4 {
+ led-ds4 {
label = "yellow";
gpios = <&pioB 1 GPIO_ACTIVE_LOW>;
linux,default-trigger = "heartbeat";
};
- ds6 {
+ led-ds6 {
label = "red";
gpios = <&pioB 2 GPIO_ACTIVE_LOW>;
};
diff --git a/arch/arm/boot/dts/microchip/at91sam9260ek.dts b/arch/arm/boot/dts/microchip/at91sam9260ek.dts
index 6bd60dce8378..e8e65e60564d 100644
--- a/arch/arm/boot/dts/microchip/at91sam9260ek.dts
+++ b/arch/arm/boot/dts/microchip/at91sam9260ek.dts
@@ -174,13 +174,13 @@ eeprom@50 {
leds {
compatible = "gpio-leds";
- ds1 {
+ led-ds1 {
label = "ds1";
gpios = <&pioA 9 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
};
- ds5 {
+ led-ds5 {
label = "ds5";
gpios = <&pioA 6 GPIO_ACTIVE_LOW>;
};
diff --git a/arch/arm/boot/dts/microchip/at91sam9261ek.dts b/arch/arm/boot/dts/microchip/at91sam9261ek.dts
index 045cb253f23a..a8f523131cd6 100644
--- a/arch/arm/boot/dts/microchip/at91sam9261ek.dts
+++ b/arch/arm/boot/dts/microchip/at91sam9261ek.dts
@@ -192,19 +192,19 @@ watchdog@fffffd40 {
leds {
compatible = "gpio-leds";
- ds8 {
+ led-ds8 {
label = "ds8";
gpios = <&pioA 13 GPIO_ACTIVE_LOW>;
linux,default-trigger = "none";
};
- ds7 {
+ led-ds7 {
label = "ds7";
gpios = <&pioA 14 GPIO_ACTIVE_LOW>;
linux,default-trigger = "nand-disk";
};
- ds1 {
+ led-ds1 {
label = "ds1";
gpios = <&pioA 23 GPIO_ACTIVE_LOW>;
linux,default-trigger = "heartbeat";
diff --git a/arch/arm/boot/dts/microchip/at91sam9263ek.dts b/arch/arm/boot/dts/microchip/at91sam9263ek.dts
index bad7dbecba3c..f25692543d71 100644
--- a/arch/arm/boot/dts/microchip/at91sam9263ek.dts
+++ b/arch/arm/boot/dts/microchip/at91sam9263ek.dts
@@ -219,13 +219,13 @@ &pioA 21 GPIO_ACTIVE_HIGH
leds {
compatible = "gpio-leds";
- d3 {
+ led-d3 {
label = "d3";
gpios = <&pioB 7 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
};
- d2 {
+ led-d2 {
label = "d2";
gpios = <&pioC 29 GPIO_ACTIVE_LOW>;
linux,default-trigger = "nand-disk";
diff --git a/arch/arm/boot/dts/microchip/at91sam9g20ek.dts b/arch/arm/boot/dts/microchip/at91sam9g20ek.dts
index 6de7a7cd3c07..1e62fd371ddb 100644
--- a/arch/arm/boot/dts/microchip/at91sam9g20ek.dts
+++ b/arch/arm/boot/dts/microchip/at91sam9g20ek.dts
@@ -14,13 +14,13 @@ / {
leds {
compatible = "gpio-leds";
- ds1 {
+ led-ds1 {
label = "ds1";
gpios = <&pioA 9 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
};
- ds5 {
+ led-ds5 {
label = "ds5";
gpios = <&pioA 6 GPIO_ACTIVE_LOW>;
};
--
2.34.1
next prev parent reply other threads:[~2024-10-01 15:27 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-10-01 15:25 [PATCH v2 0/4] Cosmetic Work for ARM/Microchip (AT91) Andrei Simion
2024-10-01 15:25 ` [PATCH v2 1/4] ARM: dts: microchip: Rename the eeprom nodename Andrei Simion
2024-10-01 15:25 ` [PATCH v2 2/4] ARM: dts: microchip: Rename the pmic node Andrei Simion
2024-10-01 15:25 ` Andrei Simion [this message]
2024-10-01 15:25 ` [PATCH v2 4/4] ARM: dts: microchip: aks-cdu: Add label for LED sub nodes Andrei Simion
2024-10-01 15:31 ` Conor Dooley
2024-10-02 10:30 ` Andrei Simion
2024-10-02 10:42 ` Alexander Dahl
2024-10-02 3:52 ` [PATCH v2 0/4] Cosmetic Work for ARM/Microchip (AT91) Rob Herring (Arm)
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20241001152541.91945-4-andrei.simion@microchip.com \
--to=andrei.simion@microchip.com \
--cc=alexandre.belloni@bootlin.com \
--cc=claudiu.beznea@tuxon.dev \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=krzk+dt@kernel.org \
--cc=krzysztof.kozlowski@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=nicolas.ferre@microchip.com \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).