[PATCH v5 0/7] Add support for PCIe3 on x1e80100

[PATCH v5 0/7] Add support for PCIe3 on x1e80100

[Qiang Yu]

This series add support for PCIe3 on x1e80100.

PCIe3 needs additional set of clocks, regulators and new set of PCIe QMP
PHY configuration compare other PCIe instances on x1e80100. Hence add
required resource configuration and usage for PCIe3.

v4->v5:
1. Add Reviewed-by tag
2. Expand and clarify usage of txz/rxz in commit message
3. Add comments that txz/rxz must be programmed before tx/rx
4. Change the sort order for phy register tbls
5. Use the order defined in struct qmp_phy_cfg_tbls for phy register tbls
   presented in x1e80100_qmp_gen4x8_pciephy_cfg
6. Add Fixes and CC stable tag
7. Fix ops for SC8280X and X1E80100
8. Document global interrupt in bindings
9. Link to v4: https://lore.kernel.org/all/20240924101444.3933828-1-quic_qianyu@quicinc.com/

v3->v4:
1. Reword commit msg of [PATCH v3 5/6]
2. Drop opp-table property from qcom,pcie-sm8450.yaml
3. Add Reviewed-by tag
4. Link to v3: https://lore.kernel.org/all/20240923125713.3411487-1-quic_qianyu@quicinc.com/

v2->v3:
1. Use 'Gen 4 x8' in commit msg
2. Move opp-table property to qcom,pcie-common.yaml
3. Add Reviewed-by tag
4. Add global interrupt and use GIC_SPI for the parent interrupt specifier
5. Use 0x0 in reg property and use pcie@ for pcie3 device node
6. Show different IP version v6.30 in commit msg
7. Add logic in controller driver to have new ops for x1e80100
8. Link to v2: https://lore.kernel.org/all/20240913083724.1217691-1-quic_qianyu@quicinc.com/

v2->v1:
1. Squash [PATCH 1/8], [PATCH 2/8],[PATCH 3/8] into one patch and make the
   indentation consistent.
2. Put dts patch at the end of the patchset.
3. Put dt-binding patch at the first of the patchset.
4. Add a new patch where opp-table is added in dt-binding to avoid dtbs
   checking error.
5. Remove GCC_PCIE_3_AUX_CLK, RPMH_CXO_CLK, put in TCSR_PCIE_8L_CLKREF_EN
   as ref.
6. Remove lane_broadcasting.
7. Add 64 bit bar, Remove GCC_PCIE_3_PIPE_CLK_SRC, 
   GCC_CFG_NOC_PCIE_ANOC_SOUTH_AHB_CLK is changed to
   GCC_CFG_NOC_PCIE_ANOC_NORTH_AHB_CLK.
8. Add Reviewed-by tag.
9. Remove [PATCH 7/8], [PATCH 8/8].
10. Link to v1: https://lore.kernel.org/all/20240827063631.3932971-1-quic_qianyu@quicinc.com/ 

Qiang Yu (7):
  dt-bindings: phy: qcom,sc8280xp-qmp-pcie-phy: Document the X1E80100
    QMP PCIe PHY Gen4 x8
  dt-bindings: PCI: qcom: Move OPP table to qcom,pcie-common.yaml
  dt-bindings: PCI: qcom,pcie-x1e80100: Add 'global' interrupt
  phy: qcom: qmp: Add phy register and clk setting for x1e80100 PCIe3
  clk: qcom: gcc-x1e80100: Fix halt_check for pipediv2 clocks
  PCI: qcom: Fix the ops for X1E80100 and SC8280X family SoC
  arm64: dts: qcom: x1e80100: Add support for PCIe3 on x1e80100

 .../bindings/pci/qcom,pcie-common.yaml        |   4 +
 .../bindings/pci/qcom,pcie-sm8450.yaml        |   4 -
 .../bindings/pci/qcom,pcie-x1e80100.yaml      |  10 +-
 .../phy/qcom,sc8280xp-qmp-pcie-phy.yaml       |   3 +
 arch/arm64/boot/dts/qcom/x1e80100.dtsi        | 204 ++++++++++++++++-
 drivers/clk/qcom/gcc-x1e80100.c               |  10 +-
 drivers/pci/controller/dwc/pcie-qcom.c        |  14 +-
 drivers/phy/qualcomm/phy-qcom-qmp-pcie.c      | 214 ++++++++++++++++++
 .../qualcomm/phy-qcom-qmp-pcs-pcie-v6_30.h    |  25 ++
 drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6_30.h |  19 ++
 10 files changed, 491 insertions(+), 16 deletions(-)
 create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-pcs-pcie-v6_30.h
 create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6_30.h

-- 
2.34.1

[PATCH v5 1/7] dt-bindings: phy: qcom,sc8280xp-qmp-pcie-phy: Document the X1E80100 QMP PCIe PHY Gen4 x8

[Qiang Yu]

PCIe 3rd instance of X1E80100 supports Gen 4 x8 which needs different
8 lane capable QMP PCIe PHY with hardware revision v6.30. Document Gen
4 x8 PHY as separate module.

Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
---
 .../devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml    | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml
index dcf4fa55fbba..680ec3113c2b 100644
--- a/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml
+++ b/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml
@@ -41,6 +41,7 @@ properties:
       - qcom,x1e80100-qmp-gen3x2-pcie-phy
       - qcom,x1e80100-qmp-gen4x2-pcie-phy
       - qcom,x1e80100-qmp-gen4x4-pcie-phy
+      - qcom,x1e80100-qmp-gen4x8-pcie-phy
 
   reg:
     minItems: 1
@@ -172,6 +173,7 @@ allOf:
               - qcom,sc8280xp-qmp-gen3x2-pcie-phy
               - qcom,sc8280xp-qmp-gen3x4-pcie-phy
               - qcom,x1e80100-qmp-gen4x4-pcie-phy
+              - qcom,x1e80100-qmp-gen4x8-pcie-phy
     then:
       properties:
         clocks:
@@ -201,6 +203,7 @@ allOf:
               - qcom,sm8550-qmp-gen4x2-pcie-phy
               - qcom,sm8650-qmp-gen4x2-pcie-phy
               - qcom,x1e80100-qmp-gen4x2-pcie-phy
+              - qcom,x1e80100-qmp-gen4x8-pcie-phy
     then:
       properties:
         resets:
-- 
2.34.1

[PATCH v5 2/7] dt-bindings: PCI: qcom: Move OPP table to qcom,pcie-common.yaml

[Qiang Yu]

OPP table is a generic property that is also required by other qcom
platforms. Hence move this property to qcom,pcie-common.yaml so that PCIe
on other qcom platforms is able to adjust power domain performance state
and ICC peak bw according to PCIe gen speed and link width.

Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
---
 Documentation/devicetree/bindings/pci/qcom,pcie-common.yaml | 4 ++++
 Documentation/devicetree/bindings/pci/qcom,pcie-sm8450.yaml | 4 ----
 2 files changed, 4 insertions(+), 4 deletions(-)

diff --git a/Documentation/devicetree/bindings/pci/qcom,pcie-common.yaml b/Documentation/devicetree/bindings/pci/qcom,pcie-common.yaml
index 704c0f58eea5..3c6430fe9331 100644
--- a/Documentation/devicetree/bindings/pci/qcom,pcie-common.yaml
+++ b/Documentation/devicetree/bindings/pci/qcom,pcie-common.yaml
@@ -78,6 +78,10 @@ properties:
     description: GPIO controlled connection to WAKE# signal
     maxItems: 1
 
+  operating-points-v2: true
+  opp-table:
+    type: object
+
 required:
   - reg
   - reg-names
diff --git a/Documentation/devicetree/bindings/pci/qcom,pcie-sm8450.yaml b/Documentation/devicetree/bindings/pci/qcom,pcie-sm8450.yaml
index 46bd59eefadb..6e0a6d8f0ed0 100644
--- a/Documentation/devicetree/bindings/pci/qcom,pcie-sm8450.yaml
+++ b/Documentation/devicetree/bindings/pci/qcom,pcie-sm8450.yaml
@@ -70,10 +70,6 @@ properties:
       - const: msi7
       - const: global
 
-  operating-points-v2: true
-  opp-table:
-    type: object
-
   resets:
     maxItems: 1
 
-- 
2.34.1

[PATCH v5 3/7] dt-bindings: PCI: qcom,pcie-x1e80100: Add 'global' interrupt

[Qiang Yu]

Document 'global' SPI interrupt along with the existing MSI interrupts so
that QCOM PCIe RC driver can make use of it to get events such as PCIe
link specific events, safety events, etc.

Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com>
---
 .../devicetree/bindings/pci/qcom,pcie-x1e80100.yaml    | 10 ++++++----
 1 file changed, 6 insertions(+), 4 deletions(-)

diff --git a/Documentation/devicetree/bindings/pci/qcom,pcie-x1e80100.yaml b/Documentation/devicetree/bindings/pci/qcom,pcie-x1e80100.yaml
index a9db0a231563..2c0e01fc0ab8 100644
--- a/Documentation/devicetree/bindings/pci/qcom,pcie-x1e80100.yaml
+++ b/Documentation/devicetree/bindings/pci/qcom,pcie-x1e80100.yaml
@@ -46,8 +46,8 @@ properties:
       - const: cnoc_sf_axi # Config NoC PCIe1 AXI clock
 
   interrupts:
-    minItems: 8
-    maxItems: 8
+    minItems: 9
+    maxItems: 9
 
   interrupt-names:
     items:
@@ -59,6 +59,7 @@ properties:
       - const: msi5
       - const: msi6
       - const: msi7
+      - const: global
 
   resets:
     minItems: 1
@@ -130,9 +131,10 @@ examples:
                          <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>,
                          <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>,
                          <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>,
-                         <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
+                         <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>,
+                         <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
             interrupt-names = "msi0", "msi1", "msi2", "msi3",
-                              "msi4", "msi5", "msi6", "msi7";
+                              "msi4", "msi5", "msi6", "msi7", "global";
             #interrupt-cells = <1>;
             interrupt-map-mask = <0 0 0 0x7>;
             interrupt-map = <0 0 0 1 &intc 0 0 0 149 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
-- 
2.34.1

Re: [PATCH v5 3/7] dt-bindings: PCI: qcom,pcie-x1e80100: Add 'global' interrupt

[Rob Herring]

On Wed, Oct 09, 2024 at 02:15:36AM -0700, Qiang Yu wrote:
> Document 'global' SPI interrupt along with the existing MSI interrupts so
> that QCOM PCIe RC driver can make use of it to get events such as PCIe
> link specific events, safety events, etc.

Is it required for some reason vs. being optional? It's fine to break 
the ABI because...?

Answer those questions with your commit msg.

> 
> Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com>
> ---
>  .../devicetree/bindings/pci/qcom,pcie-x1e80100.yaml    | 10 ++++++----
>  1 file changed, 6 insertions(+), 4 deletions(-)

[PATCH v5 4/7] phy: qcom: qmp: Add phy register and clk setting for x1e80100 PCIe3

[Qiang Yu]

Currently driver supports only x4 lane based functionality using tx/rx and
tx2/rx2 pair of register sets. To support 8 lane functionality with PCIe3,
PCIe3 related QMP PHY provides additional programming which are available
as txz and rxz based register set. Hence add txz and rxz based registers
usage and programming sequences.

As soon as software programs the txz and rxz based register set, hardware
shall "broadcast" the same settings to the tx/rx pair of registers for all
the 8 lanes, which saves the effort of software programming them one by
one.

There might be some tx and/or rx registers on some lanes need minor tweaks,
program them after programming the txz and rxz reigster set.

In addition, x1e80100 uses QMP PHY ver 6.30 for PCIe Gen4 x8, hence add
two new header files to reflect the new register offsets.

Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konradybcio@kernel.org>
---
 drivers/phy/qualcomm/phy-qcom-qmp-pcie.c      | 214 ++++++++++++++++++
 .../qualcomm/phy-qcom-qmp-pcs-pcie-v6_30.h    |  25 ++
 drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6_30.h |  19 ++
 3 files changed, 258 insertions(+)
 create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-pcs-pcie-v6_30.h
 create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6_30.h

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
index f71787fb4d7e..e7e2d69b68d6 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
@@ -34,6 +34,8 @@
 #include "phy-qcom-qmp-pcs-pcie-v5_20.h"
 #include "phy-qcom-qmp-pcs-pcie-v6.h"
 #include "phy-qcom-qmp-pcs-pcie-v6_20.h"
+#include "phy-qcom-qmp-pcs-pcie-v6_30.h"
+#include "phy-qcom-qmp-pcs-v6_30.h"
 #include "phy-qcom-qmp-pcie-qhp.h"
 
 #define PHY_INIT_COMPLETE_TIMEOUT		10000
@@ -1344,6 +1346,154 @@ static const struct qmp_phy_init_tbl x1e80100_qmp_gen4x2_pcie_pcs_misc_tbl[] = {
 	QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_G4_FOM_EQ_CONFIG5, 0x8a),
 };
 
+static const struct qmp_phy_init_tbl x1e80100_qmp_gen4x8_pcie_serdes_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_STEP_SIZE1_MODE1, 0x26),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_STEP_SIZE2_MODE1, 0x03),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_MODE1, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_RCTRL_MODE1, 0x16),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CCTRL_MODE1, 0x36),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CORECLK_DIV_MODE1, 0x08),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP1_MODE1, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP2_MODE1, 0x0d),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_DEC_START_MODE1, 0x68),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_DIV_FRAC_START1_MODE1, 0xab),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_DIV_FRAC_START2_MODE1, 0xaa),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_DIV_FRAC_START3_MODE1, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_HSCLK_SEL_1, 0x12),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_STEP_SIZE1_MODE0, 0xf8),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_STEP_SIZE2_MODE0, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_MODE0, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_RCTRL_MODE0, 0x16),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CCTRL_MODE0, 0x36),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CORE_CLK_DIV_MODE0, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP1_MODE0, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP2_MODE0, 0x0d),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_DEC_START_MODE0, 0x41),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_DIV_FRAC_START1_MODE0, 0xab),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_DIV_FRAC_START2_MODE0, 0xaa),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_DIV_FRAC_START3_MODE0, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_HSCLK_HS_SWITCH_SEL_1, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_BG_TIMER, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_EN_CENTER, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_PER1, 0x62),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_PER2, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_POST_DIV_MUX, 0x40),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_BIAS_EN_CLK_BUFLR_EN, 0x1c),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CLK_ENABLE1, 0x90),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SYS_CLK_CTRL, 0x82),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_IVCO, 0x0f),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SYSCLK_EN_SEL, 0x08),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP_EN, 0x46),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP_CFG, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_VCO_TUNE_MAP, 0x14),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CLK_SELECT, 0x34),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CORE_CLK_EN, 0x20),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CMN_CONFIG_1, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CMN_MISC_1, 0x88),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CMN_MODE, 0x14),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_VCO_DC_LEVEL_CTRL, 0x0f),
+};
+
+static const struct qmp_phy_init_tbl x1e80100_qmp_gen4x8_pcie_ln_shrd_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RXCLK_DIV2_CTRL, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_SUMMER_CAL_SPD_MODE, 0x5b),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_DFE_DAC_ENABLE1, 0x88),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_TX_ADAPT_POST_THRESH1, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_TX_ADAPT_POST_THRESH2, 0x0d),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B0, 0x12),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B1, 0x12),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B2, 0xdb),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B3, 0x9a),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B4, 0x38),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B5, 0xb6),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B6, 0x64),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH1_RATE210, 0x1f),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH1_RATE3, 0x1f),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH2_RATE210, 0x1f),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH2_RATE3, 0x1f),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH3_RATE210, 0x1f),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH3_RATE3, 0x1f),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH4_RATE3, 0x1f),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH5_RATE3, 0x1f),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH6_RATE3, 0x1f),
+};
+
+static const struct qmp_phy_init_tbl x1e80100_qmp_gen4x8_pcie_txz_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_TX_RES_CODE_LANE_OFFSET_TX, 0x1a),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_TX_RES_CODE_LANE_OFFSET_RX, 0x05),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_TX_LANE_MODE_1, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_TX_LANE_MODE_2, 0x10),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_TX_LANE_MODE_3, 0x51),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_TX_TRAN_DRVR_EMP_EN, 0x34),
+};
+
+static const struct qmp_phy_init_tbl x1e80100_qmp_gen4x8_pcie_rxz_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_UCDR_FO_GAIN_RATE_2, 0x0c),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_UCDR_SO_GAIN_RATE_2, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_UCDR_FO_GAIN_RATE_3, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_UCDR_PI_CONTROLS, 0x16),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_UCDR_SO_ACC_DEFAULT_VAL_RATE3, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_IVCM_CAL_CTRL2, 0x80),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_IVCM_POSTCAL_OFFSET, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_BKUP_CTRL1, 0x15),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_DFE_3, 0x45),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_VGA_CAL_MAN_VAL, 0x0c),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_VGA_CAL_CNTRL1, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_GM_CAL, 0x0d),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_EQU_ADAPTOR_CNTRL4, 0x0b),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_SIGDET_ENABLES, 0x1c),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_PHPRE_CTRL, 0x20),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_DFE_CTLE_POST_CAL_OFFSET, 0x38),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_Q_PI_INTRINSIC_BIAS_RATE32, 0x39),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE2_B0, 0xd4),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE2_B1, 0x23),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE2_B2, 0x58),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE2_B3, 0x9a),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE2_B4, 0x38),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE2_B5, 0xb6),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE2_B6, 0xee),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE3_B0, 0x1c),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE3_B1, 0xe4),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE3_B2, 0x60),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE3_B3, 0xdf),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE3_B4, 0x69),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE3_B5, 0x76),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE3_B6, 0xff),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_TX_ADPT_CTRL, 0x10),
+};
+
+static const struct qmp_phy_init_tbl x1e80100_qmp_gen4x8_pcie_rx_tbl[] = {
+	QMP_PHY_INIT_CFG_LANE(QSERDES_V6_20_RX_DFE_CTLE_POST_CAL_OFFSET, 0x3a, BIT(0)),
+};
+
+static const struct qmp_phy_init_tbl x1e80100_qmp_gen4x8_pcie_pcs_tbl[] = {
+	QMP_PHY_INIT_CFG(QPHY_V6_30_PCS_LOCK_DETECT_CONFIG2, 0x00),
+	QMP_PHY_INIT_CFG(QPHY_V6_30_PCS_G3S2_PRE_GAIN, 0x2e),
+	QMP_PHY_INIT_CFG(QPHY_V6_30_PCS_RX_SIGDET_LVL, 0x99),
+	QMP_PHY_INIT_CFG(QPHY_V6_30_PCS_ALIGN_DETECT_CONFIG7, 0x00),
+	QMP_PHY_INIT_CFG(QPHY_V6_30_PCS_EQ_CONFIG4, 0x00),
+	QMP_PHY_INIT_CFG(QPHY_V6_30_PCS_EQ_CONFIG5, 0x22),
+	QMP_PHY_INIT_CFG(QPHY_V6_30_PCS_TX_RX_CONFIG, 0x04),
+	QMP_PHY_INIT_CFG(QPHY_V6_30_PCS_TX_RX_CONFIG2, 0x02),
+};
+
+static const struct qmp_phy_init_tbl x1e80100_qmp_gen4x8_pcie_pcs_misc_tbl[] = {
+	QMP_PHY_INIT_CFG(QPHY_PCIE_V6_30_PCS_ENDPOINT_REFCLK_DRIVE, 0xc1),
+	QMP_PHY_INIT_CFG(QPHY_PCIE_V6_30_PCS_OSC_DTCT_ACTIONS, 0x00),
+	QMP_PHY_INIT_CFG(QPHY_PCIE_V6_30_PCS_EQ_CONFIG1, 0x16),
+	QMP_PHY_INIT_CFG(QPHY_PCIE_V6_30_PCS_G4_EQ_CONFIG5, 0x02),
+	QMP_PHY_INIT_CFG(QPHY_PCIE_V6_30_PCS_G4_PRE_GAIN, 0x2e),
+	QMP_PHY_INIT_CFG(QPHY_PCIE_V6_30_PCS_RX_MARGINING_CONFIG1, 0x03),
+	QMP_PHY_INIT_CFG(QPHY_PCIE_V6_30_PCS_RX_MARGINING_CONFIG3, 0x28),
+	QMP_PHY_INIT_CFG(QPHY_PCIE_V6_30_PCS_RX_MARGINING_CONFIG5, 0x18),
+	QMP_PHY_INIT_CFG(QPHY_PCIE_V6_30_PCS_G3_FOM_EQ_CONFIG5, 0x7a),
+	QMP_PHY_INIT_CFG(QPHY_PCIE_V6_30_PCS_G4_FOM_EQ_CONFIG5, 0x8a),
+	QMP_PHY_INIT_CFG(QPHY_PCIE_V6_30_PCS_G3_RXEQEVAL_TIME, 0x27),
+	QMP_PHY_INIT_CFG(QPHY_PCIE_V6_30_PCS_G4_RXEQEVAL_TIME, 0x27),
+	QMP_PHY_INIT_CFG(QPHY_PCIE_V6_30_PCS_TX_RX_CONFIG, 0xc0),
+	QMP_PHY_INIT_CFG(QPHY_PCIE_V6_30_PCS_POWER_STATE_CONFIG2, 0x1d),
+};
+
 static const struct qmp_phy_init_tbl sm8250_qmp_pcie_serdes_tbl[] = {
 	QMP_PHY_INIT_CFG(QSERDES_V4_COM_SYSCLK_EN_SEL, 0x08),
 	QMP_PHY_INIT_CFG(QSERDES_V4_COM_CLK_SELECT, 0x34),
@@ -2582,6 +2732,8 @@ struct qmp_pcie_offsets {
 	u16 rx;
 	u16 tx2;
 	u16 rx2;
+	u16 txz;
+	u16 rxz;
 	u16 ln_shrd;
 };
 
@@ -2592,6 +2744,10 @@ struct qmp_phy_cfg_tbls {
 	int tx_num;
 	const struct qmp_phy_init_tbl *rx;
 	int rx_num;
+	const struct qmp_phy_init_tbl *txz;
+	int txz_num;
+	const struct qmp_phy_init_tbl *rxz;
+	int rxz_num;
 	const struct qmp_phy_init_tbl *pcs;
 	int pcs_num;
 	const struct qmp_phy_init_tbl *pcs_misc;
@@ -2659,6 +2815,8 @@ struct qmp_pcie {
 	void __iomem *rx;
 	void __iomem *tx2;
 	void __iomem *rx2;
+	void __iomem *txz;
+	void __iomem *rxz;
 	void __iomem *ln_shrd;
 
 	void __iomem *port_b;
@@ -2826,6 +2984,17 @@ static const struct qmp_pcie_offsets qmp_pcie_offsets_v6_20 = {
 	.ln_shrd	= 0x0e00,
 };
 
+static const struct qmp_pcie_offsets qmp_pcie_offsets_v6_30 = {
+	.serdes		= 0x8800,
+	.pcs		= 0x9000,
+	.pcs_misc	= 0x9800,
+	.tx		= 0x0000,
+	.rx		= 0x0200,
+	.txz		= 0xe000,
+	.rxz		= 0xe200,
+	.ln_shrd	= 0x8000,
+};
+
 static const struct qmp_phy_cfg ipq8074_pciephy_cfg = {
 	.lanes			= 1,
 
@@ -3704,6 +3873,38 @@ static const struct qmp_phy_cfg x1e80100_qmp_gen4x4_pciephy_cfg = {
 	.has_nocsr_reset	= true,
 };
 
+static const struct qmp_phy_cfg x1e80100_qmp_gen4x8_pciephy_cfg = {
+	.lanes = 8,
+
+	.offsets		= &qmp_pcie_offsets_v6_30,
+	.tbls = {
+		.serdes			= x1e80100_qmp_gen4x8_pcie_serdes_tbl,
+		.serdes_num		= ARRAY_SIZE(x1e80100_qmp_gen4x8_pcie_serdes_tbl),
+		.rx			= x1e80100_qmp_gen4x8_pcie_rx_tbl,
+		.rx_num			= ARRAY_SIZE(x1e80100_qmp_gen4x8_pcie_rx_tbl),
+		.txz			= x1e80100_qmp_gen4x8_pcie_txz_tbl,
+		.txz_num		= ARRAY_SIZE(x1e80100_qmp_gen4x8_pcie_txz_tbl),
+		.rxz			= x1e80100_qmp_gen4x8_pcie_rxz_tbl,
+		.rxz_num		= ARRAY_SIZE(x1e80100_qmp_gen4x8_pcie_rxz_tbl),
+		.pcs			= x1e80100_qmp_gen4x8_pcie_pcs_tbl,
+		.pcs_num		= ARRAY_SIZE(x1e80100_qmp_gen4x8_pcie_pcs_tbl),
+		.pcs_misc		= x1e80100_qmp_gen4x8_pcie_pcs_misc_tbl,
+		.pcs_misc_num		= ARRAY_SIZE(x1e80100_qmp_gen4x8_pcie_pcs_misc_tbl),
+		.ln_shrd		= x1e80100_qmp_gen4x8_pcie_ln_shrd_tbl,
+		.ln_shrd_num		= ARRAY_SIZE(x1e80100_qmp_gen4x8_pcie_ln_shrd_tbl),
+	},
+
+	.reset_list		= sdm845_pciephy_reset_l,
+	.num_resets		= ARRAY_SIZE(sdm845_pciephy_reset_l),
+	.vreg_list		= sm8550_qmp_phy_vreg_l,
+	.num_vregs		= ARRAY_SIZE(sm8550_qmp_phy_vreg_l),
+	.regs			= pciephy_v6_regs_layout,
+
+	.pwrdn_ctrl		= SW_PWRDN | REFCLK_DRV_DSBL,
+	.phy_status		= PHYSTATUS_4_20,
+	.has_nocsr_reset	= true,
+};
+
 static void qmp_pcie_init_port_b(struct qmp_pcie *qmp, const struct qmp_phy_cfg_tbls *tbls)
 {
 	const struct qmp_phy_cfg *cfg = qmp->cfg;
@@ -3751,6 +3952,13 @@ static void qmp_pcie_init_registers(struct qmp_pcie *qmp, const struct qmp_phy_c
 
 	qmp_configure(qmp->dev, serdes, tbls->serdes, tbls->serdes_num);
 
+	/*
+	 * Tx/Rx registers that require different settings than
+	 * txz/rxz must be programmed after txz/rxz.
+	 */
+	qmp_configure(qmp->dev, qmp->txz, tbls->txz, tbls->txz_num);
+	qmp_configure(qmp->dev, qmp->rxz, tbls->rxz, tbls->rxz_num);
+
 	qmp_configure_lane(qmp->dev, tx, tbls->tx, tbls->tx_num, 1);
 	qmp_configure_lane(qmp->dev, rx, tbls->rx, tbls->rx_num, 1);
 
@@ -4293,6 +4501,9 @@ static int qmp_pcie_parse_dt(struct qmp_pcie *qmp)
 			return PTR_ERR(qmp->port_b);
 	}
 
+	qmp->txz = base + offs->txz;
+	qmp->rxz = base + offs->rxz;
+
 	if (cfg->tbls.ln_shrd)
 		qmp->ln_shrd = base + offs->ln_shrd;
 
@@ -4478,6 +4689,9 @@ static const struct of_device_id qmp_pcie_of_match_table[] = {
 	}, {
 		.compatible = "qcom,x1e80100-qmp-gen4x4-pcie-phy",
 		.data = &x1e80100_qmp_gen4x4_pciephy_cfg,
+	}, {
+		.compatible = "qcom,x1e80100-qmp-gen4x8-pcie-phy",
+		.data = &x1e80100_qmp_gen4x8_pciephy_cfg,
 	},
 	{ },
 };
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-pcs-pcie-v6_30.h b/drivers/phy/qualcomm/phy-qcom-qmp-pcs-pcie-v6_30.h
new file mode 100644
index 000000000000..5a58ff197e6e
--- /dev/null
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-pcs-pcie-v6_30.h
@@ -0,0 +1,25 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2024 Qualcomm Innovation Center. All rights reserved.
+ */
+
+#ifndef QCOM_PHY_QMP_PCS_PCIE_V6_30_H_
+#define QCOM_PHY_QMP_PCS_PCIE_V6_30_H_
+
+/* Only for QMP V6_30 PHY - PCIE have different offsets than V6 */
+#define QPHY_PCIE_V6_30_PCS_POWER_STATE_CONFIG2		0x014
+#define QPHY_PCIE_V6_30_PCS_TX_RX_CONFIG		0x020
+#define QPHY_PCIE_V6_30_PCS_ENDPOINT_REFCLK_DRIVE	0x024
+#define QPHY_PCIE_V6_30_PCS_OSC_DTCT_ACTIONS		0x098
+#define QPHY_PCIE_V6_30_PCS_EQ_CONFIG1			0x0a8
+#define QPHY_PCIE_V6_30_PCS_G3_RXEQEVAL_TIME		0x0f8
+#define QPHY_PCIE_V6_30_PCS_G4_RXEQEVAL_TIME		0x0fc
+#define QPHY_PCIE_V6_30_PCS_G4_EQ_CONFIG5		0x110
+#define QPHY_PCIE_V6_30_PCS_G4_PRE_GAIN			0x164
+#define QPHY_PCIE_V6_30_PCS_RX_MARGINING_CONFIG1	0x184
+#define QPHY_PCIE_V6_30_PCS_RX_MARGINING_CONFIG3	0x18c
+#define QPHY_PCIE_V6_30_PCS_RX_MARGINING_CONFIG5	0x194
+#define QPHY_PCIE_V6_30_PCS_G3_FOM_EQ_CONFIG5		0x1b4
+#define QPHY_PCIE_V6_30_PCS_G4_FOM_EQ_CONFIG5		0x1c8
+
+#endif
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6_30.h b/drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6_30.h
new file mode 100644
index 000000000000..369120d88bc2
--- /dev/null
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6_30.h
@@ -0,0 +1,19 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2024 Qualcomm Innovation Center. All rights reserved.
+ */
+
+#ifndef QCOM_PHY_QMP_PCS_V6_30_H_
+#define QCOM_PHY_QMP_PCS_V6_30_H_
+
+/* Only for QMP V6_30 PHY - PCIe PCS registers */
+#define QPHY_V6_30_PCS_LOCK_DETECT_CONFIG2		0x0cc
+#define QPHY_V6_30_PCS_G3S2_PRE_GAIN			0x17c
+#define QPHY_V6_30_PCS_RX_SIGDET_LVL			0x194
+#define QPHY_V6_30_PCS_ALIGN_DETECT_CONFIG7		0x1dc
+#define QPHY_V6_30_PCS_TX_RX_CONFIG			0x1e0
+#define QPHY_V6_30_PCS_TX_RX_CONFIG2			0x1e4
+#define QPHY_V6_30_PCS_EQ_CONFIG4			0x1fc
+#define QPHY_V6_30_PCS_EQ_CONFIG5			0x200
+
+#endif
-- 
2.34.1

[PATCH v5 5/7] clk: qcom: gcc-x1e80100: Fix halt_check for pipediv2 clocks

[Qiang Yu]

The pipediv2_clk's source from the same mux as pipe clock. So they have
same limitation, which is that the PHY sequence requires to enable these
local CBCs before the PHY is actually outputting a clock to them. This
means the clock won't actually turn on when we vote them. Hence, let's
skip the halt bit check of the pipediv2_clk, otherwise pipediv2_clk may
stuck at off state during bootup.

Cc: stable@vger.kernel.org
Fixes: 161b7c401f4b ("clk: qcom: Add Global Clock controller (GCC) driver for X1E80100")
Suggested-by: Mike Tipton <quic_mdtipton@quicinc.com>
Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com>
Reviewed-by: Konrad Dybcio <konradybcio@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
---
 drivers/clk/qcom/gcc-x1e80100.c | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)

diff --git a/drivers/clk/qcom/gcc-x1e80100.c b/drivers/clk/qcom/gcc-x1e80100.c
index 0f578771071f..81ba5ceab342 100644
--- a/drivers/clk/qcom/gcc-x1e80100.c
+++ b/drivers/clk/qcom/gcc-x1e80100.c
@@ -3123,7 +3123,7 @@ static struct clk_branch gcc_pcie_3_pipe_clk = {
 
 static struct clk_branch gcc_pcie_3_pipediv2_clk = {
 	.halt_reg = 0x58060,
-	.halt_check = BRANCH_HALT_VOTED,
+	.halt_check = BRANCH_HALT_SKIP,
 	.clkr = {
 		.enable_reg = 0x52020,
 		.enable_mask = BIT(5),
@@ -3248,7 +3248,7 @@ static struct clk_branch gcc_pcie_4_pipe_clk = {
 
 static struct clk_branch gcc_pcie_4_pipediv2_clk = {
 	.halt_reg = 0x6b054,
-	.halt_check = BRANCH_HALT_VOTED,
+	.halt_check = BRANCH_HALT_SKIP,
 	.clkr = {
 		.enable_reg = 0x52010,
 		.enable_mask = BIT(27),
@@ -3373,7 +3373,7 @@ static struct clk_branch gcc_pcie_5_pipe_clk = {
 
 static struct clk_branch gcc_pcie_5_pipediv2_clk = {
 	.halt_reg = 0x2f054,
-	.halt_check = BRANCH_HALT_VOTED,
+	.halt_check = BRANCH_HALT_SKIP,
 	.clkr = {
 		.enable_reg = 0x52018,
 		.enable_mask = BIT(19),
@@ -3511,7 +3511,7 @@ static struct clk_branch gcc_pcie_6a_pipe_clk = {
 
 static struct clk_branch gcc_pcie_6a_pipediv2_clk = {
 	.halt_reg = 0x31060,
-	.halt_check = BRANCH_HALT_VOTED,
+	.halt_check = BRANCH_HALT_SKIP,
 	.clkr = {
 		.enable_reg = 0x52018,
 		.enable_mask = BIT(28),
@@ -3649,7 +3649,7 @@ static struct clk_branch gcc_pcie_6b_pipe_clk = {
 
 static struct clk_branch gcc_pcie_6b_pipediv2_clk = {
 	.halt_reg = 0x8d060,
-	.halt_check = BRANCH_HALT_VOTED,
+	.halt_check = BRANCH_HALT_SKIP,
 	.clkr = {
 		.enable_reg = 0x52010,
 		.enable_mask = BIT(28),
-- 
2.34.1

[PATCH v5 6/7] PCI: qcom: Fix the ops for X1E80100 and SC8280X family SoC

[Qiang Yu]

On X1E80100 and SC8280X family SoC, PCIe controllers are connected to
SMMUv3, hence they don't need the config_sid() callback in ops_1_9_0
struct. Fix it by introducing a new ops struct, namely ops_1_21_0, so
that BDF2SID mapping won't be configured during init.

In addition, since it is recommended to disable ASPM L0s on X1E80100 as
same as SC8280X, hence X1E80100 can simply reuse cfg_sc8280xp as its
config.

Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com>
---
 drivers/pci/controller/dwc/pcie-qcom.c | 14 ++++++++++++--
 1 file changed, 12 insertions(+), 2 deletions(-)

diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
index 88a98be930e3..c533e6024ba2 100644
--- a/drivers/pci/controller/dwc/pcie-qcom.c
+++ b/drivers/pci/controller/dwc/pcie-qcom.c
@@ -1367,6 +1367,16 @@ static const struct qcom_pcie_ops ops_2_9_0 = {
 	.ltssm_enable = qcom_pcie_2_3_2_ltssm_enable,
 };
 
+/* Qcom IP rev.: 1.21.0 */
+static const struct qcom_pcie_ops ops_1_21_0 = {
+	.get_resources = qcom_pcie_get_resources_2_7_0,
+	.init = qcom_pcie_init_2_7_0,
+	.post_init = qcom_pcie_post_init_2_7_0,
+	.host_post_init = qcom_pcie_host_post_init_2_7_0,
+	.deinit = qcom_pcie_deinit_2_7_0,
+	.ltssm_enable = qcom_pcie_2_3_2_ltssm_enable,
+};
+
 static const struct qcom_pcie_cfg cfg_1_0_0 = {
 	.ops = &ops_1_0_0,
 };
@@ -1405,7 +1415,7 @@ static const struct qcom_pcie_cfg cfg_2_9_0 = {
 };
 
 static const struct qcom_pcie_cfg cfg_sc8280xp = {
-	.ops = &ops_1_9_0,
+	.ops = &ops_1_21_0,
 	.no_l0s = true,
 };
 
@@ -1837,7 +1847,7 @@ static const struct of_device_id qcom_pcie_match[] = {
 	{ .compatible = "qcom,pcie-sm8450-pcie0", .data = &cfg_1_9_0 },
 	{ .compatible = "qcom,pcie-sm8450-pcie1", .data = &cfg_1_9_0 },
 	{ .compatible = "qcom,pcie-sm8550", .data = &cfg_1_9_0 },
-	{ .compatible = "qcom,pcie-x1e80100", .data = &cfg_1_9_0 },
+	{ .compatible = "qcom,pcie-x1e80100", .data = &cfg_sc8280xp },
 	{ }
 };
 
-- 
2.34.1

Re: [PATCH v5 6/7] PCI: qcom: Fix the ops for X1E80100 and SC8280X family SoC

[Dmitry Baryshkov]

On Wed, Oct 09, 2024 at 02:15:39AM GMT, Qiang Yu wrote:
> On X1E80100 and SC8280X family SoC, PCIe controllers are connected to
> SMMUv3, hence they don't need the config_sid() callback in ops_1_9_0
> struct. Fix it by introducing a new ops struct, namely ops_1_21_0, so
> that BDF2SID mapping won't be configured during init.

Fixes tag missing. Cc:stable if required.

> 
> In addition, since it is recommended to disable ASPM L0s on X1E80100 as
> same as SC8280X, hence X1E80100 can simply reuse cfg_sc8280xp as its
> config.

Separate commit, please with its own description and Fixes tag.

> 
> Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com>
> ---
>  drivers/pci/controller/dwc/pcie-qcom.c | 14 ++++++++++++--
>  1 file changed, 12 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
> index 88a98be930e3..c533e6024ba2 100644
> --- a/drivers/pci/controller/dwc/pcie-qcom.c
> +++ b/drivers/pci/controller/dwc/pcie-qcom.c
> @@ -1367,6 +1367,16 @@ static const struct qcom_pcie_ops ops_2_9_0 = {
>  	.ltssm_enable = qcom_pcie_2_3_2_ltssm_enable,
>  };
>  
> +/* Qcom IP rev.: 1.21.0 */
> +static const struct qcom_pcie_ops ops_1_21_0 = {
> +	.get_resources = qcom_pcie_get_resources_2_7_0,
> +	.init = qcom_pcie_init_2_7_0,
> +	.post_init = qcom_pcie_post_init_2_7_0,
> +	.host_post_init = qcom_pcie_host_post_init_2_7_0,
> +	.deinit = qcom_pcie_deinit_2_7_0,
> +	.ltssm_enable = qcom_pcie_2_3_2_ltssm_enable,
> +};
> +
>  static const struct qcom_pcie_cfg cfg_1_0_0 = {
>  	.ops = &ops_1_0_0,
>  };
> @@ -1405,7 +1415,7 @@ static const struct qcom_pcie_cfg cfg_2_9_0 = {
>  };
>  
>  static const struct qcom_pcie_cfg cfg_sc8280xp = {
> -	.ops = &ops_1_9_0,
> +	.ops = &ops_1_21_0,
>  	.no_l0s = true,
>  };
>  
> @@ -1837,7 +1847,7 @@ static const struct of_device_id qcom_pcie_match[] = {
>  	{ .compatible = "qcom,pcie-sm8450-pcie0", .data = &cfg_1_9_0 },
>  	{ .compatible = "qcom,pcie-sm8450-pcie1", .data = &cfg_1_9_0 },
>  	{ .compatible = "qcom,pcie-sm8550", .data = &cfg_1_9_0 },
> -	{ .compatible = "qcom,pcie-x1e80100", .data = &cfg_1_9_0 },
> +	{ .compatible = "qcom,pcie-x1e80100", .data = &cfg_sc8280xp },
>  	{ }
>  };
>  
> -- 
> 2.34.1
> 

-- 
With best wishes
Dmitry

[PATCH v5 7/7] arm64: dts: qcom: x1e80100: Add support for PCIe3 on x1e80100

[Qiang Yu]

Describe PCIe3 controller and PHY. Also add required system resources like
regulators, clocks, interrupts and registers configuration for PCIe3.

Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
---
 arch/arm64/boot/dts/qcom/x1e80100.dtsi | 204 ++++++++++++++++++++++++-
 1 file changed, 203 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/qcom/x1e80100.dtsi b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
index a36076e3c56b..c615c930cf0c 100644
--- a/arch/arm64/boot/dts/qcom/x1e80100.dtsi
+++ b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
@@ -744,7 +744,7 @@ gcc: clock-controller@100000 {
 
 			clocks = <&bi_tcxo_div2>,
 				 <&sleep_clk>,
-				 <0>,
+				 <&pcie3_phy>,
 				 <&pcie4_phy>,
 				 <&pcie5_phy>,
 				 <&pcie6a_phy>,
@@ -2907,6 +2907,208 @@ mmss_noc: interconnect@1780000 {
 			#interconnect-cells = <2>;
 		};
 
+		pcie3: pcie@1bd0000 {
+			device_type = "pci";
+			compatible = "qcom,pcie-x1e80100";
+			reg = <0x0 0x01bd0000 0x0 0x3000>,
+			      <0x0 0x78000000 0x0 0xf1d>,
+			      <0x0 0x78000f40 0x0 0xa8>,
+			      <0x0 0x78001000 0x0 0x1000>,
+			      <0x0 0x78100000 0x0 0x100000>,
+			      <0x0 0x01bd3000 0x0 0x1000>;
+			reg-names = "parf",
+				    "dbi",
+				    "elbi",
+				    "atu",
+				    "config",
+				    "mhi";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			ranges = <0x01000000 0x0 0x00000000 0x0 0x78200000 0x0 0x100000>,
+				 <0x02000000 0x0 0x78300000 0x0 0x78300000 0x0 0x3d00000>,
+				 <0x03000000 0x7 0x40000000 0x7 0x40000000 0x0 0x40000000>;
+			bus-range = <0x00 0xff>;
+
+			dma-coherent;
+
+			linux,pci-domain = <3>;
+			num-lanes = <8>;
+
+			interrupts = <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 769 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 836 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 671 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi0",
+					  "msi1",
+					  "msi2",
+					  "msi3",
+					  "msi4",
+					  "msi5",
+					  "msi6",
+					  "msi7",
+					  "global";
+
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 0 GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 2 &intc 0 0 GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 3 &intc 0 0 GIC_SPI 237 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 4 &intc 0 0 GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&gcc GCC_PCIE_3_AUX_CLK>,
+				 <&gcc GCC_PCIE_3_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_3_MSTR_AXI_CLK>,
+				 <&gcc GCC_PCIE_3_SLV_AXI_CLK>,
+				 <&gcc GCC_PCIE_3_SLV_Q2A_AXI_CLK>,
+				 <&gcc GCC_CFG_NOC_PCIE_ANOC_NORTH_AHB_CLK>,
+				 <&gcc GCC_CNOC_PCIE_NORTH_SF_AXI_CLK>;
+			clock-names = "aux",
+				      "cfg",
+				      "bus_master",
+				      "bus_slave",
+				      "slave_q2a",
+				      "noc_aggr",
+				      "cnoc_sf_axi";
+
+			assigned-clocks = <&gcc GCC_PCIE_3_AUX_CLK>;
+			assigned-clock-rates = <19200000>;
+
+			interconnects = <&pcie_south_anoc MASTER_PCIE_3 QCOM_ICC_TAG_ALWAYS
+					 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>,
+					<&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
+					 &cnoc_main SLAVE_PCIE_3 QCOM_ICC_TAG_ALWAYS>;
+			interconnect-names = "pcie-mem",
+					     "cpu-pcie";
+
+			resets = <&gcc GCC_PCIE_3_BCR>,
+				 <&gcc GCC_PCIE_3_LINK_DOWN_BCR>;
+			reset-names = "pci",
+				      "link_down";
+
+			power-domains = <&gcc GCC_PCIE_3_GDSC>;
+
+			phys = <&pcie3_phy>;
+			phy-names = "pciephy";
+
+			operating-points-v2 = <&pcie3_opp_table>;
+
+			status = "disabled";
+
+			pcie3_opp_table: opp-table {
+				compatible = "operating-points-v2";
+
+				/* GEN 1 x1 */
+				opp-2500000 {
+					opp-hz = /bits/ 64 <2500000>;
+					required-opps = <&rpmhpd_opp_low_svs>;
+					opp-peak-kBps = <250000 1>;
+				};
+
+				/* GEN 1 x2 and GEN 2 x1 */
+				opp-5000000 {
+					opp-hz = /bits/ 64 <5000000>;
+					required-opps = <&rpmhpd_opp_low_svs>;
+					opp-peak-kBps = <500000 1>;
+				};
+
+				/* GEN 1 x4 and GEN 2 x2 */
+				opp-10000000 {
+					opp-hz = /bits/ 64 <10000000>;
+					required-opps = <&rpmhpd_opp_low_svs>;
+					opp-peak-kBps = <1000000 1>;
+				};
+
+				/* GEN 1 x8 and GEN 2 x4 */
+				opp-20000000 {
+					opp-hz = /bits/ 64 <20000000>;
+					required-opps = <&rpmhpd_opp_low_svs>;
+					opp-peak-kBps = <2000000 1>;
+				};
+
+				/* GEN 2 x8 */
+				opp-40000000 {
+					opp-hz = /bits/ 64 <40000000>;
+					required-opps = <&rpmhpd_opp_low_svs>;
+					opp-peak-kBps = <4000000 1>;
+				};
+
+				/* GEN 3 x1 */
+				opp-8000000 {
+					opp-hz = /bits/ 64 <8000000>;
+					required-opps = <&rpmhpd_opp_svs>;
+					opp-peak-kBps = <984500 1>;
+				};
+
+				/* GEN 3 x2 and GEN 4 x1 */
+				opp-16000000 {
+					opp-hz = /bits/ 64 <16000000>;
+					required-opps = <&rpmhpd_opp_svs>;
+					opp-peak-kBps = <1969000 1>;
+				};
+
+				/* GEN 3 x4 and GEN 4 x2 */
+				opp-32000000 {
+					opp-hz = /bits/ 64 <32000000>;
+					required-opps = <&rpmhpd_opp_svs>;
+					opp-peak-kBps = <3938000 1>;
+				};
+
+				/* GEN 3 x8 and GEN 4 x4 */
+				opp-64000000 {
+					opp-hz = /bits/ 64 <64000000>;
+					required-opps = <&rpmhpd_opp_svs>;
+					opp-peak-kBps = <7876000 1>;
+				};
+
+				/* GEN 4 x8 */
+				opp-128000000 {
+					opp-hz = /bits/ 64 <128000000>;
+					required-opps = <&rpmhpd_opp_svs>;
+					opp-peak-kBps = <15753000 1>;
+				};
+			};
+		};
+
+		pcie3_phy: phy@1be0000 {
+			compatible = "qcom,x1e80100-qmp-gen4x8-pcie-phy";
+			reg = <0 0x01be0000 0 0x10000>;
+
+			clocks = <&gcc GCC_PCIE_3_PHY_AUX_CLK>,
+				 <&gcc GCC_PCIE_3_CFG_AHB_CLK>,
+				 <&tcsr TCSR_PCIE_8L_CLKREF_EN>,
+				 <&gcc GCC_PCIE_3_PHY_RCHNG_CLK>,
+				 <&gcc GCC_PCIE_3_PIPE_CLK>,
+				 <&gcc GCC_PCIE_3_PIPEDIV2_CLK>;
+			clock-names = "aux",
+				      "cfg_ahb",
+				      "ref",
+				      "rchng",
+				      "pipe",
+				      "pipediv2";
+
+			resets = <&gcc GCC_PCIE_3_PHY_BCR>,
+				 <&gcc GCC_PCIE_3_NOCSR_COM_PHY_BCR>;
+			reset-names = "phy",
+				      "phy_nocsr";
+
+			assigned-clocks = <&gcc GCC_PCIE_3_PHY_RCHNG_CLK>;
+			assigned-clock-rates = <100000000>;
+
+			power-domains = <&gcc GCC_PCIE_3_PHY_GDSC>;
+
+			#clock-cells = <0>;
+			clock-output-names = "pcie3_pipe_clk";
+
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
 		pcie6a: pci@1bf8000 {
 			device_type = "pci";
 			compatible = "qcom,pcie-x1e80100";
-- 
2.34.1