Re: [PATCH v8 2/3] arm64: dts: imx95: add usb3 related nodes

[Xu Yang <xu.yang_2@nxp.com>]

On Wed, Oct 16, 2024 at 10:53:50AM +0200, Alexander Stein wrote:
> Hi,
> 
> another thing I just noticed.
> 
> Am Dienstag, 15. Oktober 2024, 13:10:17 CEST schrieb Xu Yang:
> > Add usb3 phy and controller nodes for imx95.
> > 
> > Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
> > 
> > ---
> > Changes in v2:
> >  - no changes
> > Changes in v3:
> >  - no changes
> > Changes in v4:
> >  - reorder nodes
> > Changes in v5:
> >  - no changes
> > Changes in v6:
> >  - rebase to latest
> > Changes in v7:
> >  - no changes
> > Changes in v8:
> >  - no changes
> > ---
> >  arch/arm64/boot/dts/freescale/imx95.dtsi | 43 ++++++++++++++++++++++++
> >  1 file changed, 43 insertions(+)
> > 
> > diff --git a/arch/arm64/boot/dts/freescale/imx95.dtsi b/arch/arm64/boot/dts/freescale/imx95.dtsi
> > index 03661e76550f..e3faa8462759 100644
> > --- a/arch/arm64/boot/dts/freescale/imx95.dtsi
> > +++ b/arch/arm64/boot/dts/freescale/imx95.dtsi
> > @@ -1473,6 +1473,49 @@ smmu: iommu@490d0000 {
> >  			};
> >  		};
> >  
> > +		usb3: usb@4c010010 {
> > +			compatible = "fsl,imx95-dwc3", "fsl,imx8mp-dwc3";
> > +			reg = <0x0 0x4c010010 0x0 0x04>,
> > +			      <0x0 0x4c1f0000 0x0 0x20>;
> > +			clocks = <&scmi_clk IMX95_CLK_HSIO>,
> > +				 <&scmi_clk IMX95_CLK_32K>;
> > +			clock-names = "hsio", "suspend";
> > +			interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>;
> > +			#address-cells = <2>;
> > +			#size-cells = <2>;
> > +			ranges;
> > +			power-domains = <&scmi_devpd IMX95_PD_HSIO_TOP>;
> > +			dma-ranges = <0x0 0x0 0x0 0x0 0x10 0x0>;
> > +			status = "disabled";
> > +
> > +			usb3_dwc3: usb@4c100000 {
> > +				compatible = "snps,dwc3";
> > +				reg = <0x0 0x4c100000 0x0 0x10000>;
> > +				clocks = <&scmi_clk IMX95_CLK_HSIO>,
> > +					 <&scmi_clk IMX95_CLK_24M>,
> > +					 <&scmi_clk IMX95_CLK_32K>;
> > +				clock-names = "bus_early", "ref", "suspend";
> > +				interrupts = <GIC_SPI 175 IRQ_TYPE_LEVEL_HIGH>;
> > +				phys = <&usb3_phy>, <&usb3_phy>;
> > +				phy-names = "usb2-phy", "usb3-phy";
> > +				snps,gfladj-refclk-lpm-sel-quirk;
> > +				snps,parkmode-disable-ss-quirk;
> > +				iommus = <&smmu 0xe>;
> > +			};
> > +		};
> > +
> > +		usb3_phy: phy@4c1f0040 {
> > +			compatible = "fsl,imx95-usb-phy", "fsl,imx8mp-usb-phy";
> > +			reg = <0x0 0x4c1f0040 0x0 0x40>,
> > +			      <0x0 0x4c1fc000 0x0 0x100>;
> > +			clocks = <&scmi_clk IMX95_CLK_HSIO>;
> > +			clock-names = "phy";
> > +			#phy-cells = <0>;
> > +			power-domains = <&scmi_devpd IMX95_PD_HSIO_TOP>;
> > +			orientation-switch;
> > +			status = "disabled";
> 
> I got these dtbs check warnings:
> 
> arch/arm64/boot/dts/freescale/imx95-tqma9596sa-mb-smarc-2.dtb:
>  phy@4c1f0040: 'oneOf' conditional failed, one must be fixed:
>         'port' is a required property
>         'ports' is a required property
>         from schema $id: http://devicetree.org/schemas/phy/fsl,imx8mq-usb-phy.yaml#
> arch/arm64/boot/dts/freescale/imx95-tqma9596sa-mb-smarc-2.dtb: 
>  phy@4c1f0040: Unevaluated properties are not allowed ('orientation-switch' was unexpected)
>         from schema $id: http://devicetree.org/schemas/phy/fsl,imx8mq-usb-phy.yaml#

Are you checking on usb tree? You need below two dt-binding patch.

 - dt-bindings: usb: dwc3-imx8mp: add compatible string for imx95
 - dt-bindings: phy: imx8mq-usb: add compatible "fsl,imx95-usb-phy"

> 
> 
> How am I supposed to specify a port when the usb3 is used in host mode, thus
> no USB Type-C connector and no 'port' OF-graph accordingly?

Host-only mode with Type-A connector? No Typec-C connector?
Sorry, I do not get your meaning.

Thanks,
Xu Yang