[PATCH 3/5] arm64: dts: qcom: Add pmd8028 and pmih0108 PMIC dtsi files

[Melody Olvera <quic_molvera@quicinc.com>]

From: Jishnu Prakash <quic_jprakash@quicinc.com>

Add dtsi files for pmd8028 and pmih0108 PMICs, used on SM8750
platforms.

Signed-off-by: Jishnu Prakash <quic_jprakash@quicinc.com>
Signed-off-by: Melody Olvera <quic_molvera@quicinc.com>
---
 arch/arm64/boot/dts/qcom/pmd8028.dtsi  | 56 +++++++++++++++++++++++
 arch/arm64/boot/dts/qcom/pmih0108.dtsi | 62 ++++++++++++++++++++++++++
 2 files changed, 118 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/pmd8028.dtsi
 create mode 100644 arch/arm64/boot/dts/qcom/pmih0108.dtsi

diff --git a/arch/arm64/boot/dts/qcom/pmd8028.dtsi b/arch/arm64/boot/dts/qcom/pmd8028.dtsi
new file mode 100644
index 000000000000..f8ef8e133854
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pmd8028.dtsi
@@ -0,0 +1,56 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+/ {
+	thermal-zones {
+		pmd8028-thermal {
+			polling-delay-passive = <100>;
+			thermal-sensors = <&pmd8028_temp_alarm>;
+
+			trips {
+				pmd8028_trip0: trip0 {
+					temperature = <95000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				pmd8028_trip1: trip1 {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "hot";
+				};
+			};
+		};
+	};
+};
+
+&spmi_bus {
+	pmd8028: pmic@4 {
+		compatible = "qcom,pmd8028", "qcom,spmi-pmic";
+		reg = <0x4 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pmd8028_temp_alarm: temp-alarm@a00 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0xa00>;
+			interrupts = <0x4 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+			#thermal-sensor-cells = <0>;
+		};
+
+		pmd8028_gpios: gpio@8800 {
+			compatible = "qcom,pmd8028-gpio", "qcom,spmi-gpio";
+			reg = <0x8800>;
+			gpio-controller;
+			gpio-ranges = <&pmd8028_gpios 0 0 4>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/pmih0108.dtsi b/arch/arm64/boot/dts/qcom/pmih0108.dtsi
new file mode 100644
index 000000000000..c868ebf77213
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pmih0108.dtsi
@@ -0,0 +1,62 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+/ {
+	thermal-zones {
+		pmih0108-thermal {
+			polling-delay-passive = <100>;
+			thermal-sensors = <&pmih0108_temp_alarm>;
+
+			trips {
+				trip0 {
+					temperature = <95000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "hot";
+				};
+			};
+		};
+	};
+};
+
+&spmi_bus {
+	pmih0108: pmic@7 {
+		compatible = "qcom,pmih0108", "qcom,spmi-pmic";
+		reg = <0x7 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pmih0108_temp_alarm: temp-alarm@a00 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0xa00>;
+			interrupts = <0x7 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+			#thermal-sensor-cells = <0>;
+		};
+
+		pmih0108_gpios: gpio@8800 {
+			compatible = "qcom,pmih0108-gpio", "qcom,spmi-gpio";
+			reg = <0x8800>;
+			gpio-controller;
+			gpio-ranges = <&pmih0108_gpios 0 0 18>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		pmih0108_eusb2_repeater: eusb2-repeater@fd00 {
+			compatible = "qcom,pm8550b-eusb2-repeater";
+			reg = <0xfd00>;
+			#phy-cells = <0>;
+		};
+	};
+};
-- 
2.46.1