[net-next RFC PATCH v2 1/3] dt-bindings: net: dsa: Add Airoha AN8855 Gigabit Switch documentation

[Christian Marangi <ansuelsmth@gmail.com>]

Add Airoha AN8855 5 port Gigabit Switch documentation.

The switch node requires an additional mdio node to describe each internal
PHY relative offset as the PHY address for the switch match the one for
the PHY ports. On top of internal PHY address, the switch base PHY address
is added.

Also the switch base PHY address can be configured and changed after the
first initialization. On reset, the switch PHY address is ALWAYS 1.
This can be configured with the use of "airoha,base_smi_address".

Calibration values might be stored in switch EFUSE and internal PHY
might need to be calibrated, in such case, airoha,ext_surge needs to be
enabled and relative NVMEM cells needs to be defined in nvmem-layout
node.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
---
 .../bindings/net/dsa/airoha,an8855.yaml       | 253 ++++++++++++++++++
 1 file changed, 253 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/net/dsa/airoha,an8855.yaml

diff --git a/Documentation/devicetree/bindings/net/dsa/airoha,an8855.yaml b/Documentation/devicetree/bindings/net/dsa/airoha,an8855.yaml
new file mode 100644
index 000000000000..5982b4c39536
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dsa/airoha,an8855.yaml
@@ -0,0 +1,253 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/dsa/airoha,an8855.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Airoha AN8855 Gigabit switch
+
+maintainers:
+  - Christian Marangi <ansuelsmth@gmail.com>
+
+description:
+  Airoha AN8855 is a 5-port Gigabit Switch.
+
+  The switch node requires an additional mdio node to describe each internal
+  PHY relative offset as the PHY address for the switch match the one for
+  the PHY ports. On top of internal PHY address, the switch base PHY address
+  is added.
+
+  Also the switch base PHY address can be configured and changed after the
+  first initialization. On reset, the switch PHY address is ALWAYS 1.
+
+properties:
+  compatible:
+    const: airoha,an8855
+
+  reg:
+    maxItems: 1
+
+  reset-gpios:
+    description:
+      GPIO to be used to reset the whole device
+    maxItems: 1
+
+  airoha,base_smi_address:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Configure and change the base switch PHY address to a new address on
+      the bus.
+      On reset, the switch PHY address is ALWAYS 1.
+    default: 1
+    maximum: 31
+
+  airoha,ext_surge:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      Calibrate the internal PHY with the calibration values stored in EFUSE
+      for the r50Ohm values.
+
+  '#nvmem-cell-cells':
+    const: 0
+
+  nvmem-layout:
+    $ref: /schemas/nvmem/layouts/nvmem-layout.yaml
+    description:
+      NVMEM Layout for exposed EFUSE. (for example to propagate calibration
+      value for r50Ohm for internal PHYs)
+
+  mdio:
+    $ref: /schemas/net/mdio.yaml#
+    unevaluatedProperties: false
+    description:
+      Define the relative address of the internal PHY for each port.
+
+      Each reg for the PHY is relative to the switch base PHY address.
+
+$ref: dsa.yaml#
+
+required:
+  - compatible
+  - reg
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    mdio {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        switch@1 {
+            compatible = "airoha,an8855";
+            reg = <1>;
+            reset-gpios = <&pio 39 0>;
+
+            airoha,ext_surge;
+
+            #nvmem-cell-cells = <0>;
+
+            nvmem-layout {
+                compatible = "fixed-layout";
+                #address-cells = <1>;
+                #size-cells = <1>;
+
+                shift_sel_port0_tx_a: shift-sel-port0-tx-a@c {
+                    reg = <0xc 0x4>;
+                };
+
+                shift_sel_port0_tx_b: shift-sel-port0-tx-b@10 {
+                    reg = <0x10 0x4>;
+                };
+
+                shift_sel_port0_tx_c: shift-sel-port0-tx-c@14 {
+                    reg = <0x14 0x4>;
+                };
+
+                shift_sel_port0_tx_d: shift-sel-port0-tx-d@18 {
+                    reg = <0x18 0x4>;
+                };
+
+                shift_sel_port1_tx_a: shift-sel-port1-tx-a@1c {
+                    reg = <0x1c 0x4>;
+                };
+
+                shift_sel_port1_tx_b: shift-sel-port1-tx-b@20 {
+                    reg = <0x20 0x4>;
+                };
+
+                shift_sel_port1_tx_c: shift-sel-port1-tx-c@24 {
+                    reg = <0x24 0x4>;
+                };
+
+                shift_sel_port1_tx_d: shift-sel-port1-tx-d@28 {
+                    reg = <0x28 0x4>;
+                };
+
+                shift_sel_port2_tx_a: shift-sel-port2-tx-a@2c {
+                    reg = <0x2c 0x4>;
+                };
+
+                shift_sel_port2_tx_b: shift-sel-port2-tx-b@30 {
+                    reg = <0x30 0x4>;
+                };
+
+                shift_sel_port2_tx_c: shift-sel-port2-tx-c@34 {
+                    reg = <0x34 0x4>;
+                };
+
+                shift_sel_port2_tx_d: shift-sel-port2-tx-d@38 {
+                    reg = <0x38 0x4>;
+                };
+
+                shift_sel_port3_tx_a: shift-sel-port3-tx-a@4c {
+                    reg = <0x4c 0x4>;
+                };
+
+                shift_sel_port3_tx_b: shift-sel-port3-tx-b@50 {
+                    reg = <0x50 0x4>;
+                };
+
+                shift_sel_port3_tx_c: shift-sel-port3-tx-c@54 {
+                    reg = <0x54 0x4>;
+                };
+
+                shift_sel_port3_tx_d: shift-sel-port3-tx-d@58 {
+                    reg = <0x58 0x4>;
+                };
+            };
+
+            ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                port@0 {
+                    reg = <0>;
+                    label = "lan1";
+                    phy-mode = "internal";
+                    phy-handle = <&internal_phy0>;
+                };
+
+                port@1 {
+                    reg = <1>;
+                    label = "lan2";
+                    phy-mode = "internal";
+                    phy-handle = <&internal_phy1>;
+                };
+
+                port@2 {
+                    reg = <2>;
+                    label = "lan3";
+                    phy-mode = "internal";
+                    phy-handle = <&internal_phy2>;
+                };
+
+                port@3 {
+                    reg = <3>;
+                    label = "lan4";
+                    phy-mode = "internal";
+                    phy-handle = <&internal_phy3>;
+                };
+
+                port@5 {
+                    reg = <5>;
+                    label = "cpu";
+                    ethernet = <&gmac0>;
+                    phy-mode = "2500base-x";
+
+                    fixed-link {
+                        speed = <2500>;
+                        full-duplex;
+                        pause;
+                    };
+                };
+            };
+
+            mdio {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                internal_phy0: phy@0 {
+                    reg = <0>;
+
+                    nvmem-cells = <&shift_sel_port0_tx_a>,
+                                  <&shift_sel_port0_tx_b>,
+                                  <&shift_sel_port0_tx_c>,
+                                  <&shift_sel_port0_tx_d>;
+                    nvmem-cell-names = "tx_a", "tx_b", "tx_c", "tx_d";
+                };
+
+                internal_phy1: phy@1 {
+                    reg = <1>;
+
+                    nvmem-cells = <&shift_sel_port1_tx_a>,
+                                  <&shift_sel_port1_tx_b>,
+                                  <&shift_sel_port1_tx_c>,
+                                  <&shift_sel_port1_tx_d>;
+                    nvmem-cell-names = "tx_a", "tx_b", "tx_c", "tx_d";
+                };
+
+                internal_phy2: phy@2 {
+                    reg = <2>;
+
+                    nvmem-cells = <&shift_sel_port2_tx_a>,
+                                  <&shift_sel_port2_tx_b>,
+                                  <&shift_sel_port2_tx_c>,
+                                  <&shift_sel_port2_tx_d>;
+                    nvmem-cell-names = "tx_a", "tx_b", "tx_c", "tx_d";
+                };
+
+                internal_phy3: phy@3 {
+                    reg = <3>;
+
+                    nvmem-cells = <&shift_sel_port3_tx_a>,
+                                  <&shift_sel_port3_tx_b>,
+                                  <&shift_sel_port3_tx_c>,
+                                  <&shift_sel_port3_tx_d>;
+                    nvmem-cell-names = "tx_a", "tx_b", "tx_c", "tx_d";
+                };
+            };
+        };
+    };
-- 
2.45.2