Re: [PATCH v3 2/6] arm64: dts: qcom: qcs6490-rb3gen2: Add node for qps615

[Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>]

On Tue, Nov 12, 2024 at 08:31:34PM +0530, Krishna chaitanya chundru wrote:
> Add QPS615 PCIe switch node which has 3 downstream ports and in one
> downstream port two embedded ethernet devices are present.
> 
> Power to the QPS615 is supplied through two LDO regulators, controlled
> by two GPIOs, these are added as fixed regulators. And the QPS615 is
> configured through i2c.
> 
> Signed-off-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>

Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>

One comment below.

> ---
>  arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts | 115 +++++++++++++++++++++++++++
>  arch/arm64/boot/dts/qcom/sc7280.dtsi         |   2 +-
>  2 files changed, 116 insertions(+), 1 deletion(-)
> 
> diff --git a/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts b/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
> index 0d45662b8028..0e890841b600 100644
> --- a/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
> +++ b/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
> @@ -202,6 +202,30 @@ vph_pwr: vph-pwr-regulator {
>  		regulator-min-microvolt = <3700000>;
>  		regulator-max-microvolt = <3700000>;
>  	};
> +
> +	vdd_ntn_0p9: regulator-vdd-ntn-0p9 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VDD_NTN_0P9";
> +		gpio = <&pm8350c_gpios 2 GPIO_ACTIVE_HIGH>;
> +		regulator-min-microvolt = <899400>;
> +		regulator-max-microvolt = <899400>;
> +		enable-active-high;
> +		pinctrl-0 = <&ntn_0p9_en>;
> +		pinctrl-names = "default";
> +		regulator-enable-ramp-delay = <4300>;
> +	};
> +
> +	vdd_ntn_1p8: regulator-vdd-ntn-1p8 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VDD_NTN_1P8";
> +		gpio = <&pm8350c_gpios 3 GPIO_ACTIVE_HIGH>;
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +		enable-active-high;
> +		pinctrl-0 = <&ntn_1p8_en>;
> +		pinctrl-names = "default";
> +		regulator-enable-ramp-delay = <10000>;
> +	};
>  };
>  
>  &apps_rsc {
> @@ -684,6 +708,75 @@ &mdss_edp_phy {
>  	status = "okay";
>  };
>  
> +&pcie1_port {
> +	pcie@0,0 {
> +		compatible = "pci1179,0623";
> +		reg = <0x10000 0x0 0x0 0x0 0x0>;
> +		#address-cells = <3>;
> +		#size-cells = <2>;
> +
> +		device_type = "pci";
> +		ranges;
> +		bus-range = <0x2 0xff>;
> +
> +		vddc-supply = <&vdd_ntn_0p9>;
> +		vdd18-supply = <&vdd_ntn_1p8>;
> +		vdd09-supply = <&vdd_ntn_0p9>;
> +		vddio1-supply = <&vdd_ntn_1p8>;
> +		vddio2-supply = <&vdd_ntn_1p8>;
> +		vddio18-supply = <&vdd_ntn_1p8>;
> +
> +		i2c-parent = <&i2c0 0x77>;
> +
> +		reset-gpios = <&pm8350c_gpios 1 GPIO_ACTIVE_LOW>;
> +
> +		pcie@1,0 {
> +			reg = <0x20800 0x0 0x0 0x0 0x0>;
> +			#address-cells = <3>;
> +			#size-cells = <2>;
> +
> +			device_type = "pci";
> +			ranges;
> +			bus-range = <0x3 0xff>;
> +		};
> +
> +		pcie@2,0 {
> +			reg = <0x21000 0x0 0x0 0x0 0x0>;
> +			#address-cells = <3>;
> +			#size-cells = <2>;
> +
> +			device_type = "pci";
> +			ranges;
> +			bus-range = <0x4 0xff>;
> +		};
> +
> +		pcie@3,0 {
> +			reg = <0x21800 0x0 0x0 0x0 0x0>;
> +			#address-cells = <3>;
> +			#size-cells = <2>;
> +			device_type = "pci";
> +			ranges;
> +			bus-range = <0x5 0xff>;
> +

You haven't added any additional properties (dfe etc...) to any of the
downstream port nodes. Does this mean that this board doesn't need any of them?

- Mani

-- 
மணிவண்ணன் சதாசிவம்