[PATCH v6 0/4] Add support for NetCube Systems Kumquat

[PATCH v6 0/4] Add support for NetCube Systems Kumquat

[Lukas Schmid]

This series adds dt-bindings and dt's for the NetCube Systems Kumquat
board.

Changes in v2:
  Fix the devicetrees according to the 
    "dt-schema" and "make dtbs_check W=1"
  Fix the License of the devicetree as requested
  Create a cover letter for the patch series

Changes in v3:
  Disable rtc inside the SoC again, as the rtc does not work on the
    board
  Add the gpio-reserved-ranges property to the pinctrl bindings
  Reorder the nodes in the devicetree to match the order of the nodes 
    in the sun8i-v3s.dtsi file

Changes in v4:
  Moved the dtsi change into a sperate patch
  Update commit messages to include better descriptions
  Add descriptions to the uarts and mmc nodes in the dts file
  Add missing newline at the end of the dts file
  Removed the gpio-reserved-ranges property from the dts and
    from the pinctrl bindings
  Remove the rtc status property from the dts file

Changes in v5:
  Remove the unused lradc node and it's regualtor, as they
    are not used on the board
  Add another alias for the SoC's rtc as 'rtc1'

Changes in v6:
  Add reason why DS3232+ is preferred over internal rtc
  Remove redundant pinctrls from mmc0, mmc1 and i2c0
  Reordered eeprom0 and spi0/flash@0 properties
  Reordered nodes by their node name alias

Signed-off-by: Lukas Schmid <lukas.schmid@netcube.li>
---
Lukas Schmid (4):
  dt-bindings: vendor-prefixes: Add NetCube Systems Austria name
  dt-bindings: arm: sunxi: Add NetCube Systems Kumquat board
  ARM: dts: sunxi: add uart1_pe pinctrl for sun8i-v3s
  ARM: dts: sunxi: add support for NetCube Systems Kumquat

 .../devicetree/bindings/arm/sunxi.yaml        |   5 +
 .../devicetree/bindings/vendor-prefixes.yaml  |   2 +
 arch/arm/boot/dts/allwinner/Makefile          |   2 +
 .../allwinner/sun8i-v3s-netcube-kumquat.dts   | 268 ++++++++++++++++++
 arch/arm/boot/dts/allwinner/sun8i-v3s.dtsi    |   6 +
 5 files changed, 283 insertions(+)
 create mode 100644 arch/arm/boot/dts/allwinner/sun8i-v3s-netcube-kumquat.dts

-- 
2.47.1

[PATCH v6 1/4] dt-bindings: vendor-prefixes: Add NetCube Systems Austria name

[Lukas Schmid]

NetCube Systems Austria builds Embedded Systems for use in IoT, IIoT,
or Smart Home scenarios.

Website is still WIP, but the Links on it are active:
https://netcubesystems.at/

Signed-off-by: Lukas Schmid <lukas.schmid@netcube.li>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index da01616802c7..a30ed9547098 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -1027,6 +1027,8 @@ patternProperties:
     description: Neofidelity Inc.
   "^neonode,.*":
     description: Neonode Inc.
+  "^netcube,.*":
+    description: NetCube Systems Austria
   "^netgear,.*":
     description: NETGEAR
   "^netlogic,.*":
-- 
2.47.1

[PATCH v6 2/4] dt-bindings: arm: sunxi: Add NetCube Systems Kumquat board

[Lukas Schmid]

The NetCube Systems Kumquat is an Embedded Controller based
on the Allwinner V3s SoC. It is intended for Smart Home or
Industrial automation without the need for a traditional PLC

Signed-off-by: Lukas Schmid <lukas.schmid@netcube.li>
---
 Documentation/devicetree/bindings/arm/sunxi.yaml | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/sunxi.yaml b/Documentation/devicetree/bindings/arm/sunxi.yaml
index 046536d02706..f536cdd2c1a6 100644
--- a/Documentation/devicetree/bindings/arm/sunxi.yaml
+++ b/Documentation/devicetree/bindings/arm/sunxi.yaml
@@ -589,6 +589,11 @@ properties:
           - const: emlid,neutis-n5h3
           - const: allwinner,sun8i-h3
 
+      - description: NetCube Systems Kumquat
+        items:
+          - const: netcube,kumquat
+          - const: allwinner,sun8i-v3s
+
       - description: NextThing Co. CHIP
         items:
           - const: nextthing,chip
-- 
2.47.1

[PATCH v6 3/4] ARM: dts: sunxi: add uart1_pe pinctrl for sun8i-v3s

[Lukas Schmid]

Added the uart1_pe_pins pinctrl for use by the NetCube
Systems Kumquat board

Signed-off-by: Lukas Schmid <lukas.schmid@netcube.li>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
---
 arch/arm/boot/dts/allwinner/sun8i-v3s.dtsi | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/arch/arm/boot/dts/allwinner/sun8i-v3s.dtsi b/arch/arm/boot/dts/allwinner/sun8i-v3s.dtsi
index 9e13c2aa8911..f909b1d4dbca 100644
--- a/arch/arm/boot/dts/allwinner/sun8i-v3s.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun8i-v3s.dtsi
@@ -416,6 +416,12 @@ uart0_pb_pins: uart0-pb-pins {
 				function = "uart0";
 			};
 
+			/omit-if-no-ref/
+			uart1_pe_pins: uart1-pe-pins {
+				pins = "PE21", "PE22";
+				function = "uart1";
+			};
+
 			uart2_pins: uart2-pins {
 				pins = "PB0", "PB1";
 				function = "uart2";
-- 
2.47.1

[PATCH v6 4/4] ARM: dts: sunxi: add support for NetCube Systems Kumquat

[Lukas Schmid]

NetCube Systems Kumquat is a board based on the Allwinner V3s SoC,
including:

- 64MB DDR2 included in SoC
- 10/100 Mbps Ethernet
- USB-C DRD
- Audio Codec
- Isolated CAN-FD
- ESP32 over SDIO
- 8MB SPI-NOR Flash for bootloader
- I2C EEPROM for MAC addresses
- SDIO Connector for eMMC or SD-Card
- 8x 12/24V IOs, 4x normally open relays
- DS3232 RTC
- QWIIC connectors for external I2C devices

Signed-off-by: Lukas Schmid <lukas.schmid@netcube.li>
---
 arch/arm/boot/dts/allwinner/Makefile          |   2 +
 .../allwinner/sun8i-v3s-netcube-kumquat.dts   | 268 ++++++++++++++++++
 2 files changed, 270 insertions(+)
 create mode 100644 arch/arm/boot/dts/allwinner/sun8i-v3s-netcube-kumquat.dts

diff --git a/arch/arm/boot/dts/allwinner/Makefile b/arch/arm/boot/dts/allwinner/Makefile
index 48666f73e638..d799ad153b37 100644
--- a/arch/arm/boot/dts/allwinner/Makefile
+++ b/arch/arm/boot/dts/allwinner/Makefile
@@ -199,6 +199,7 @@ DTC_FLAGS_sun8i-h3-nanopi-r1 := -@
 DTC_FLAGS_sun8i-h3-orangepi-pc := -@
 DTC_FLAGS_sun8i-h3-bananapi-m2-plus-v1.2 := -@
 DTC_FLAGS_sun8i-h3-orangepi-pc-plus := -@
+DTC_FLAGS_sun8i-v3s-netcube-kumquat := -@
 dtb-$(CONFIG_MACH_SUN8I) += \
 	sun8i-a23-evb.dtb \
 	sun8i-a23-gt90h-v4.dtb \
@@ -261,6 +262,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
 	sun8i-v3s-anbernic-rg-nano.dtb \
 	sun8i-v3s-licheepi-zero.dtb \
 	sun8i-v3s-licheepi-zero-dock.dtb \
+	sun8i-v3s-netcube-kumquat.dtb \
 	sun8i-v40-bananapi-m2-berry.dtb
 dtb-$(CONFIG_MACH_SUN9I) += \
 	sun9i-a80-optimus.dtb \
diff --git a/arch/arm/boot/dts/allwinner/sun8i-v3s-netcube-kumquat.dts b/arch/arm/boot/dts/allwinner/sun8i-v3s-netcube-kumquat.dts
new file mode 100644
index 000000000000..019042700558
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun8i-v3s-netcube-kumquat.dts
@@ -0,0 +1,268 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2025 Lukas Schmid <lukas.schmid@netcube.li>
+ */
+
+/dts-v1/;
+#include "sun8i-v3s.dtsi"
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/{
+	model = "NetCube Systems Kumquat";
+	compatible = "netcube,kumquat", "allwinner,sun8i-v3s";
+
+	aliases {
+		serial0 = &uart0;
+		ethernet0 = &emac;
+		rtc0 = &ds3232;
+		rtc1 = &rtc; /* not battery backed */
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	/* 40 MHz Crystal Oscillator on PCB */
+	clk_can0: clock-can0 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency  = <40000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+
+		key-user {
+			label = "GPIO Key User";
+			linux,code = <KEY_PROG1>;
+			gpios = <&pio 1 2 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PB2 */
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-heartbeat {
+			gpios = <&pio 4 4 GPIO_ACTIVE_HIGH>; /* PE4 */
+			linux,default-trigger = "heartbeat";
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_HEARTBEAT;
+		};
+
+		led-mmc0-act {
+			gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+			linux,default-trigger = "mmc0";
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_DISK;
+		};
+	};
+
+	/* EA3036C Switching 3 Channel Regulator - Channel 2 */
+	reg_vcc3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&reg_vcc5v0>;
+	};
+
+	/* K7805-1000R3 Switching Regulator supplied from main 12/24V terminal block */
+	reg_vcc5v0: regulator-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+};
+
+&codec {
+	allwinner,audio-routing =
+		"Headphone", "HP",
+		"Headphone", "HPCOM",
+		"MIC1", "Mic",
+		"Mic", "HBIAS";
+	status = "okay";
+};
+
+&ehci {
+	status = "okay";
+};
+
+&emac {
+	allwinner,leds-active-low;
+	nvmem-cells = <&eth0_macaddress>;
+	nvmem-cell-names = "mac-address";
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	ds3232: rtc@68 {
+		compatible = "dallas,ds3232";
+		reg = <0x68>;
+	};
+
+	eeprom0: eeprom@50 {
+		compatible = "atmel,24c02";		/* actually it's a 24AA02E48 */
+		reg = <0x50>;
+		pagesize = <16>;
+		read-only;
+		vcc-supply = <&reg_vcc3v3>;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		eth0_macaddress: macaddress@fa {
+			reg = <0xfa 0x06>;
+		};
+	};
+
+	tusb320: typec@60 {
+		compatible = "ti,tusb320";
+		reg = <0x60>;
+		interrupt-parent = <&pio>;
+		interrupts = <1 5 IRQ_TYPE_EDGE_FALLING>;
+	};
+};
+
+/* Exposed as the Flash/SD Header on the board */
+&mmc0 {
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	broken-cd;
+	status = "okay";
+};
+
+/* Connected to the on-board ESP32 */
+&mmc1 {
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	broken-cd;
+	status = "okay";
+};
+
+&ohci {
+	status = "okay";
+};
+
+&pio {
+	vcc-pb-supply = <&reg_vcc3v3>;
+	vcc-pc-supply = <&reg_vcc3v3>;
+	vcc-pe-supply = <&reg_vcc3v3>;
+	vcc-pf-supply = <&reg_vcc3v3>;
+	vcc-pg-supply = <&reg_vcc3v3>;
+
+	gpio-line-names = "", "", "", "", // PA
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "CAN_nCS", "CAN_nINT", "USER_SW", "PB3", // PB
+			  "USB_ID", "USBC_nINT", "I2C0_SCL", "I2C0_SDA",
+			  "UART0_TX", "UART0_RX", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "SPI_MISO", "SPI_SCK", "FLASH_nCS", "SPI_MOSI", // PC
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "", // PD
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "Q12", "Q11", "Q10", "Q9", // PE
+			  "LED_SYS0", "I1", "Q1", "Q2",
+			  "I2", "I3", "Q3", "Q4",
+			  "I4", "I5", "Q5", "Q6",
+			  "I6", "I7", "Q7", "Q8",
+			  "I8", "UART1_TXD", "UART1_RXD", "ESP_nRST",
+			  "ESP_nBOOT", "", "", "",
+			  "", "", "", "",
+			  "SD_D1", "SD_D0", "SD_CLK", "SD_CMD", // PF
+			  "SD_D3", "SD_D2", "LED_SYS1", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "ESP_CLK", "ESP_CMD", "ESP_D0", "ESP_D1", // PG
+			  "ESP_D2", "ESP_D3", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+/* Exposed as a USB-C connector with USB-Serial converter */
+&uart0 {
+	pinctrl-0 = <&uart0_pb_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+/* Connected to the Bootloader/Console of the ESP32 */
+&uart1 {
+	pinctrl-0 = <&uart1_pe_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&usb_otg {
+	extcon = <&tusb320 0>;
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
+	status = "okay";
+};
+
+&spi0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	cs-gpios = <0>, <&pio 1 0 GPIO_ACTIVE_LOW>; /* PB0 */
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		label = "firmware";
+		spi-max-frequency = <40000000>;
+	};
+
+	can@1 {
+		compatible = "microchip,mcp2518fd";
+		reg = <1>;
+		clocks = <&clk_can0>;
+		interrupt-parent = <&pio>;
+		interrupts = <1 1 IRQ_TYPE_LEVEL_LOW>;  /* PB1 */
+		spi-max-frequency = <20000000>;
+		vdd-supply = <&reg_vcc3v3>;
+		xceiver-supply = <&reg_vcc3v3>;
+	};
+};
-- 
2.47.1