Re: [PATCH v3 3/3] drm: bridge: ti-sn65dsi83: Add error recovery mechanism

[Maxime Ripard <mripard@kernel.org>]

[-- Attachment #1: Type: text/plain, Size: 4247 bytes --]

On Wed, Jan 08, 2025 at 11:19:02AM +0100, Herve Codina wrote:
> In some cases observed during ESD tests, the TI SN65DSI83 cannot recover
> from errors by itself. A full restart of the bridge is needed in those
> cases to have the bridge output LVDS signals again.
> 
> Also, during tests, cases were observed where reading the status of the
> bridge was not even possible. Indeed, in those cases, the bridge stops
> to acknowledge I2C transactions. Only a full reset of the bridge (power
> off/on) brings back the bridge to a functional state.
> 
> The TI SN65DSI83 has some error detection capabilities. Introduce an
> error recovery mechanism based on this detection.
> 
> The errors detected are signaled through an interrupt. On system where
> this interrupt is not available, the driver uses a polling monitoring
> fallback to check for errors. When an error is present or when reading
> the bridge status leads to an I2C failure, the recovery process is
> launched.
> 
> Restarting the bridge needs to redo the initialization sequence. This
> initialization sequence has to be done with the DSI data lanes driven in
> LP11 state. In order to do that, the recovery process resets the whole
> output path (i.e the path from the encoder to the connector) where the
> bridge is located.
> 
> Signed-off-by: Herve Codina <herve.codina@bootlin.com>
> ---
>  drivers/gpu/drm/bridge/ti-sn65dsi83.c | 147 ++++++++++++++++++++++++++
>  1 file changed, 147 insertions(+)
> 
> diff --git a/drivers/gpu/drm/bridge/ti-sn65dsi83.c b/drivers/gpu/drm/bridge/ti-sn65dsi83.c
> index e6264514bb3f..74bc05647436 100644
> --- a/drivers/gpu/drm/bridge/ti-sn65dsi83.c
> +++ b/drivers/gpu/drm/bridge/ti-sn65dsi83.c
> @@ -35,9 +35,12 @@
>  #include <linux/of_graph.h>
>  #include <linux/regmap.h>
>  #include <linux/regulator/consumer.h>
> +#include <linux/timer.h>
> +#include <linux/workqueue.h>
>  
>  #include <drm/drm_atomic_helper.h>
>  #include <drm/drm_bridge.h>
> +#include <drm/drm_drv.h> /* DRM_MODESET_LOCK_ALL_BEGIN() needs drm_drv_uses_atomic_modeset() */
>  #include <drm/drm_mipi_dsi.h>
>  #include <drm/drm_of.h>
>  #include <drm/drm_panel.h>
> @@ -147,6 +150,9 @@ struct sn65dsi83 {
>  	struct regulator		*vcc;
>  	bool				lvds_dual_link;
>  	bool				lvds_dual_link_even_odd_swap;
> +	bool				use_irq;
> +	struct delayed_work		monitor_work;
> +	struct work_struct		reset_work;
>  };
>  
>  static const struct regmap_range sn65dsi83_readable_ranges[] = {
> @@ -328,6 +334,111 @@ static u8 sn65dsi83_get_dsi_div(struct sn65dsi83 *ctx)
>  	return dsi_div - 1;
>  }
>  
> +static int sn65dsi83_reset_pipe(struct sn65dsi83 *sn65dsi83)
> +{
> +	struct drm_atomic_state *state = ERR_PTR(-EINVAL);
> +	struct drm_device *dev = sn65dsi83->bridge.dev;
> +	struct drm_connector_state *connector_state;
> +	struct drm_modeset_acquire_ctx ctx;
> +	struct drm_connector *connector;
> +	int err;
> +
> +	/*
> +	 * Reset active outputs of the related CRTC.
> +	 *
> +	 * This way, drm core will reconfigure each components in the CRTC
> +	 * outputs path. In our case, this will force the previous component to
> +	 * go back in LP11 mode and so allow the reconfiguration of SN64DSI83
> +	 * bridge.
> +	 *
> +	 * Keep the lock during the whole operation to be atomic.
> +	 */
> +
> +	DRM_MODESET_LOCK_ALL_BEGIN(dev, ctx, 0, err);
> +
> +	state = drm_atomic_helper_duplicate_state(dev, &ctx);
> +	if (IS_ERR(state)) {
> +		err = PTR_ERR(state);
> +		goto unlock;
> +	}

No, you must not allocate a new state for this, you need to reuse the
existing state. You'll find it in bridge->base.state->state.

> +	state->acquire_ctx = &ctx;
> +
> +	connector = drm_atomic_get_old_connector_for_encoder(state,
> +							     sn65dsi83->bridge.encoder);
> +	if (!connector) {
> +		err = -EINVAL;
> +		goto unlock;
> +	}
> +
> +	connector_state = drm_atomic_get_connector_state(state, connector);
> +	if (IS_ERR(connector_state)) {
> +		err = PTR_ERR(connector_state);
> +		goto unlock;
> +	}
> +
> +	err = drm_atomic_helper_reset_pipe(connector_state->crtc, &ctx);
> +	if (err < 0)
> +		goto unlock;

And you'll find the crtc in bridge->encoder->crtc.

Maxime

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 273 bytes --]