From: Stephen Boyd <swboyd@chromium.org>
To: Konrad Dybcio <konradybcio@kernel.org>,
Bjorn Andersson <andersson@kernel.org>
Cc: linux-kernel@vger.kernel.org, linux-arm-msm@vger.kernel.org,
patches@lists.linux.dev, cros-qcom-dts-watchers@chromium.org,
Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>,
devicetree@vger.kernel.org, Pin-yen Lin <treapking@chromium.org>
Subject: [PATCH v2 2/2] arm64: dts: qcom: sc7180-trogdor: Wire up USB to usb-c-connectors
Date: Wed, 5 Feb 2025 15:30:15 -0800 [thread overview]
Message-ID: <20250205233016.1600517-3-swboyd@chromium.org> (raw)
In-Reply-To: <20250205233016.1600517-1-swboyd@chromium.org>
Fully describe the USB type-c on sc7180 Trogdor devices. Most Trogdor
devices have two USB type-c ports (i.e. usb-c-connector nodes), but
Quackingstick only has one. Also, clamshell devices such as Lazor have a
USB webcam connected to the USB hub, while detachable devices such as
Wormdingler don't have a webcam, or a USB type-a connector. Instead they
have the pogo pins for the detachable keyboard.
Fully describing the topology like this will let us expose information
about what devices are connected to which physical USB connector (type-A
or type-C).
Cc: <cros-qcom-dts-watchers@chromium.org>
Cc: Bjorn Andersson <andersson@kernel.org>
Cc: Konrad Dybcio <konradybcio@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Krzysztof Kozlowski <krzk+dt@kernel.org>
Cc: Conor Dooley <conor+dt@kernel.org>
Cc: <linux-arm-msm@vger.kernel.org>
Cc: <devicetree@vger.kernel.org>
Cc: Pin-yen Lin <treapking@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
---
.../dts/qcom/sc7180-trogdor-clamshell.dtsi | 21 ++++
.../boot/dts/qcom/sc7180-trogdor-coachz.dtsi | 47 ++++++++
.../dts/qcom/sc7180-trogdor-detachable.dtsi | 15 +++
.../dts/qcom/sc7180-trogdor-homestar.dtsi | 47 ++++++++
.../dts/qcom/sc7180-trogdor-kingoftown.dts | 55 +++++++++
.../boot/dts/qcom/sc7180-trogdor-lazor.dtsi | 55 +++++++++
.../boot/dts/qcom/sc7180-trogdor-pazquel.dtsi | 55 +++++++++
.../boot/dts/qcom/sc7180-trogdor-pompom.dtsi | 44 +++++++
.../qcom/sc7180-trogdor-quackingstick.dtsi | 31 +++++
.../arm64/boot/dts/qcom/sc7180-trogdor-r1.dts | 56 ++++++++-
.../dts/qcom/sc7180-trogdor-wormdingler.dtsi | 47 ++++++++
arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi | 109 ++++++++++++++++++
12 files changed, 580 insertions(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-clamshell.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-clamshell.dtsi
index d91533b80e76..4e4f0b239f3c 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-clamshell.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-clamshell.dtsi
@@ -7,3 +7,24 @@
/* This file must be included after sc7180-trogdor.dtsi to modify cros_ec */
#include <arm/cros-ec-keyboard.dtsi>
+
+/ {
+ usb-a-connector {
+ compatible = "usb-a-connector";
+
+ port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usb_a0_hs: endpoint@0 {
+ reg = <0>;
+ /* Endpoint filled in by board */
+ };
+
+ usb_a0_ss: endpoint@1 {
+ reg = <1>;
+ /* Endpoint filled in by board */
+ };
+ };
+ };
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz.dtsi
index 25b17b0425f2..548d6c1ee050 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz.dtsi
@@ -134,6 +134,17 @@ skin-temp-thermistor@1 {
};
};
+&pogo_pins {
+ keyboard@4 {
+ compatible = "usb18d1,504c";
+ reg = <4>;
+ };
+};
+
+&pogo_pins_in {
+ remote-endpoint = <&usb_hub_dfp4_hs>;
+};
+
&pp1800_uf_cam {
status = "okay";
};
@@ -175,6 +186,42 @@ &sound_multimedia0_codec {
sound-dai = <&adau7002>;
};
+&usb_c0_hs {
+ remote-endpoint = <&usb_hub_dfp1_hs>;
+};
+
+&usb_c0_ss {
+ remote-endpoint = <&usb_hub_dfp1_ss>;
+};
+
+&usb_c1_hs {
+ remote-endpoint = <&usb_hub_dfp2_hs>;
+};
+
+&usb_c1_ss {
+ remote-endpoint = <&usb_hub_dfp2_ss>;
+};
+
+&usb_hub_dfp1_hs {
+ remote-endpoint = <&usb_c0_hs>;
+};
+
+&usb_hub_dfp1_ss {
+ remote-endpoint = <&usb_c0_ss>;
+};
+
+&usb_hub_dfp2_hs {
+ remote-endpoint = <&usb_c1_hs>;
+};
+
+&usb_hub_dfp2_ss {
+ remote-endpoint = <&usb_c1_ss>;
+};
+
+&usb_hub_dfp4_hs {
+ remote-endpoint = <&pogo_pins_in>;
+};
+
/* PINCTRL - modifications to sc7180-trogdor.dtsi */
&en_pp3300_dx_edp {
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-detachable.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-detachable.dtsi
index 7c5d8a57ef7f..a863295356e9 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-detachable.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-detachable.dtsi
@@ -6,6 +6,21 @@
*/
/* This file must be included after sc7180-trogdor.dtsi to modify cros_ec */
+
+/ {
+ pogo_pins: pogo-pin-connector {
+ compatible = "google,pogo-pin-connector";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ /* Detachable keyboard populated for each board */
+ port {
+ pogo_pins_in: endpoint {
+ /* Endpoint filled in by board */
+ };
+ };
+ };
+};
+
&cros_ec {
keyboard-controller {
compatible = "google,cros-ec-keyb-switches";
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-homestar.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-homestar.dtsi
index f57976906d63..09c4a30d96ef 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-homestar.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-homestar.dtsi
@@ -159,6 +159,17 @@ skin-temp-thermistor@1 {
};
};
+&pogo_pins {
+ keyboard@3 {
+ compatible = "usb18d1,5052";
+ reg = <3>;
+ };
+};
+
+&pogo_pins_in {
+ remote-endpoint = <&usb_hub_dfp3_hs>;
+};
+
&pp1800_uf_cam {
status = "okay";
};
@@ -187,6 +198,42 @@ &sound_multimedia1_codec {
sound-dai = <&max98360a>, <&max98360a_1>, <&max98360a_2>, <&max98360a_3> ;
};
+&usb_c0_hs {
+ remote-endpoint = <&usb_hub_dfp2_hs>;
+};
+
+&usb_c0_ss {
+ remote-endpoint = <&usb_hub_dfp2_ss>;
+};
+
+&usb_c1_hs {
+ remote-endpoint = <&usb_hub_dfp4_hs>;
+};
+
+&usb_c1_ss {
+ remote-endpoint = <&usb_hub_dfp4_ss>;
+};
+
+&usb_hub_dfp2_hs {
+ remote-endpoint = <&usb_c0_hs>;
+};
+
+&usb_hub_dfp2_ss {
+ remote-endpoint = <&usb_c0_ss>;
+};
+
+&usb_hub_dfp3_hs {
+ remote-endpoint = <&pogo_pins_in>;
+};
+
+&usb_hub_dfp4_hs {
+ remote-endpoint = <&usb_c1_hs>;
+};
+
+&usb_hub_dfp4_ss {
+ remote-endpoint = <&usb_c1_ss>;
+};
+
&wifi {
qcom,ath10k-calibration-variant = "GO_HOMESTAR";
};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-kingoftown.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-kingoftown.dts
index 655bea928e52..d4ff26fba3be 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-kingoftown.dts
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-kingoftown.dts
@@ -78,6 +78,61 @@ &pp3300_dx_edp {
gpio = <&tlmm 67 GPIO_ACTIVE_HIGH>;
};
+&usb_a0_hs {
+ remote-endpoint = <&usb_hub_dfp3_hs>;
+};
+
+&usb_a0_ss {
+ remote-endpoint = <&usb_hub_dfp3_ss>;
+};
+
+&usb_c0_hs {
+ remote-endpoint = <&usb_hub_dfp1_hs>;
+};
+
+&usb_c0_ss {
+ remote-endpoint = <&usb_hub_dfp1_ss>;
+};
+
+&usb_c1_hs {
+ remote-endpoint = <&usb_hub_dfp2_hs>;
+};
+
+&usb_c1_ss {
+ remote-endpoint = <&usb_hub_dfp2_ss>;
+};
+
+&usb_hub_2_x {
+ camera@4 {
+ compatible = "usb4f2,b75a";
+ reg = <4>;
+ };
+};
+
+&usb_hub_dfp1_hs {
+ remote-endpoint = <&usb_c0_hs>;
+};
+
+&usb_hub_dfp1_ss {
+ remote-endpoint = <&usb_c0_ss>;
+};
+
+&usb_hub_dfp2_hs {
+ remote-endpoint = <&usb_c1_hs>;
+};
+
+&usb_hub_dfp2_ss {
+ remote-endpoint = <&usb_c1_ss>;
+};
+
+&usb_hub_dfp3_hs {
+ remote-endpoint = <&usb_a0_hs>;
+};
+
+&usb_hub_dfp3_ss {
+ remote-endpoint = <&usb_a0_ss>;
+};
+
&wifi {
qcom,ath10k-calibration-variant = "GO_KINGOFTOWN";
};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor.dtsi
index c3fd6760de7a..7b545ae5791b 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor.dtsi
@@ -68,6 +68,61 @@ &trackpad {
interrupts = <58 IRQ_TYPE_EDGE_FALLING>;
};
+&usb_a0_hs {
+ remote-endpoint = <&usb_hub_dfp3_hs>;
+};
+
+&usb_a0_ss {
+ remote-endpoint = <&usb_hub_dfp3_ss>;
+};
+
+&usb_c0_hs {
+ remote-endpoint = <&usb_hub_dfp2_hs>;
+};
+
+&usb_c0_ss {
+ remote-endpoint = <&usb_hub_dfp2_ss>;
+};
+
+&usb_c1_hs {
+ remote-endpoint = <&usb_hub_dfp4_hs>;
+};
+
+&usb_c1_ss {
+ remote-endpoint = <&usb_hub_dfp4_ss>;
+};
+
+&usb_hub_2_x {
+ camera@1 {
+ compatible = "usb408,a092";
+ reg = <1>;
+ };
+};
+
+&usb_hub_dfp2_hs {
+ remote-endpoint = <&usb_c0_hs>;
+};
+
+&usb_hub_dfp2_ss {
+ remote-endpoint = <&usb_c0_ss>;
+};
+
+&usb_hub_dfp3_hs {
+ remote-endpoint = <&usb_a0_hs>;
+};
+
+&usb_hub_dfp3_ss {
+ remote-endpoint = <&usb_a0_ss>;
+};
+
+&usb_hub_dfp4_hs {
+ remote-endpoint = <&usb_c1_hs>;
+};
+
+&usb_hub_dfp4_ss {
+ remote-endpoint = <&usb_c1_ss>;
+};
+
&wifi {
qcom,ath10k-calibration-variant = "GO_LAZOR";
};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-pazquel.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-pazquel.dtsi
index cc2c5610a279..9523843f06ab 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-pazquel.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-pazquel.dtsi
@@ -82,6 +82,61 @@ &pp3300_dx_edp {
gpio = <&tlmm 67 GPIO_ACTIVE_HIGH>;
};
+&usb_a0_hs {
+ remote-endpoint = <&usb_hub_dfp3_hs>;
+};
+
+&usb_a0_ss {
+ remote-endpoint = <&usb_hub_dfp3_ss>;
+};
+
+&usb_c0_hs {
+ remote-endpoint = <&usb_hub_dfp1_hs>;
+};
+
+&usb_c0_ss {
+ remote-endpoint = <&usb_hub_dfp1_ss>;
+};
+
+&usb_c1_hs {
+ remote-endpoint = <&usb_hub_dfp2_hs>;
+};
+
+&usb_c1_ss {
+ remote-endpoint = <&usb_hub_dfp2_ss>;
+};
+
+&usb_hub_2_x {
+ camera@4 {
+ compatible = "usb5c8,b03";
+ reg = <4>;
+ };
+};
+
+&usb_hub_dfp1_hs {
+ remote-endpoint = <&usb_c0_hs>;
+};
+
+&usb_hub_dfp1_ss {
+ remote-endpoint = <&usb_c0_ss>;
+};
+
+&usb_hub_dfp2_hs {
+ remote-endpoint = <&usb_c1_hs>;
+};
+
+&usb_hub_dfp2_ss {
+ remote-endpoint = <&usb_c1_ss>;
+};
+
+&usb_hub_dfp3_hs {
+ remote-endpoint = <&usb_a0_hs>;
+};
+
+&usb_hub_dfp3_ss {
+ remote-endpoint = <&usb_a0_ss>;
+};
+
/* PINCTRL - modifications to sc7180-trogdor.dtsi */
&en_pp3300_dx_edp {
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom.dtsi
index f7300ffbb451..4cc1a155d999 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom.dtsi
@@ -176,10 +176,54 @@ &sound {
dmic-gpios = <&tlmm 86 GPIO_ACTIVE_HIGH>;
};
+&usb_a0_hs {
+ remote-endpoint = <&usb_hub_dfp4_hs>;
+};
+
+&usb_a0_ss {
+ remote-endpoint = <&usb_hub_dfp4_ss>;
+};
+
+&usb_c0_hs {
+ remote-endpoint = <&usb_hub_dfp3_hs>;
+};
+
+&usb_c0_ss {
+ remote-endpoint = <&usb_hub_dfp3_ss>;
+};
+
&usb_c1 {
status = "disabled";
};
+&usb_hub_2_x {
+ camera@1 {
+ compatible = "usb4f2,b718";
+ reg = <1>;
+ };
+
+ camera@2 {
+ compatible = "usb13d3,56e9";
+ reg = <2>;
+ };
+};
+
+&usb_hub_dfp3_hs {
+ remote-endpoint = <&usb_c0_hs>;
+};
+
+&usb_hub_dfp3_ss {
+ remote-endpoint = <&usb_c0_ss>;
+};
+
+&usb_hub_dfp4_hs {
+ remote-endpoint = <&usb_a0_hs>;
+};
+
+&usb_hub_dfp4_ss {
+ remote-endpoint = <&usb_a0_ss>;
+};
+
&wifi {
qcom,ath10k-calibration-variant = "GO_POMPOM";
};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-quackingstick.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-quackingstick.dtsi
index ff8996b4de4e..174efd3abfa5 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-quackingstick.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-quackingstick.dtsi
@@ -105,6 +105,17 @@ &sdhc_2 {
status = "okay";
};
+&pogo_pins {
+ keyboard@1 {
+ compatible = "usb18d1,505b";
+ reg = <1>;
+ };
+};
+
+&pogo_pins_in {
+ remote-endpoint = <&usb_hub_dfp1_hs>;
+};
+
&pp1800_uf_cam {
status = "okay";
};
@@ -129,11 +140,31 @@ pp3300_disp_on: &pp3300_dx_edp {
gpio = <&tlmm 67 GPIO_ACTIVE_HIGH>;
};
+&usb_c0_hs {
+ remote-endpoint = <&usb_hub_dfp2_hs>;
+};
+
+&usb_c0_ss {
+ remote-endpoint = <&usb_hub_dfp2_ss>;
+};
+
/* This board only has 1 USB Type-C port. */
&usb_c1 {
status = "disabled";
};
+&usb_hub_dfp2_hs {
+ remote-endpoint = <&usb_c0_hs>;
+};
+
+&usb_hub_dfp2_ss {
+ remote-endpoint = <&usb_c0_ss>;
+};
+
+&usb_hub_dfp1_hs {
+ remote-endpoint = <&pogo_pins_in>;
+};
+
/* PINCTRL - modifications to sc7180-trogdor.dtsi */
/*
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-r1.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-r1.dts
index d393a2712ce6..dddf92c04c4d 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-r1.dts
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-r1.dts
@@ -52,12 +52,64 @@ &trackpad {
interrupts = <58 IRQ_TYPE_EDGE_FALLING>;
};
+&usb_a0_hs {
+ remote-endpoint = <&usb_hub_dfp3_hs>;
+};
+
+&usb_a0_ss {
+ remote-endpoint = <&usb_hub_dfp3_ss>;
+};
+
+&usb_c0_hs {
+ remote-endpoint = <&usb_hub_dfp2_hs>;
+};
+
+&usb_c0_ss {
+ remote-endpoint = <&usb_hub_dfp2_ss>;
+};
+
+&usb_c1_hs {
+ remote-endpoint = <&usb_hub_dfp4_hs>;
+};
+
+&usb_c1_ss {
+ remote-endpoint = <&usb_hub_dfp4_ss>;
+};
+
&usb_hub_2_x {
- vdd-supply = <&pp3300_l7c>;
+ vdd-supply = <&pp3300_l7c>;
+ camera@1 {
+ compatible = "usb4f2,b567";
+ reg = <1>;
+ };
};
&usb_hub_3_x {
- vdd-supply = <&pp3300_l7c>;
+ vdd-supply = <&pp3300_l7c>;
+};
+
+&usb_hub_dfp2_hs {
+ remote-endpoint = <&usb_c0_hs>;
+};
+
+&usb_hub_dfp2_ss {
+ remote-endpoint = <&usb_c0_ss>;
+};
+
+&usb_hub_dfp3_hs {
+ remote-endpoint = <&usb_a0_hs>;
+};
+
+&usb_hub_dfp3_ss {
+ remote-endpoint = <&usb_a0_ss>;
+};
+
+&usb_hub_dfp4_hs {
+ remote-endpoint = <&usb_c1_hs>;
+};
+
+&usb_hub_dfp4_ss {
+ remote-endpoint = <&usb_c1_ss>;
};
/* PINCTRL - modifications to sc7180-trogdor.dtsi */
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-wormdingler.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-wormdingler.dtsi
index d4925be3b1fc..59cdf8eea647 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-wormdingler.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-wormdingler.dtsi
@@ -179,6 +179,17 @@ skin-temp-thermistor@1 {
};
};
+&pogo_pins {
+ keyboard@3 {
+ compatible = "usb18d1,5057";
+ reg = <3>;
+ };
+};
+
+&pogo_pins_in {
+ remote-endpoint = <&usb_hub_dfp3_hs>;
+};
+
&pp1800_uf_cam {
status = "okay";
};
@@ -195,6 +206,42 @@ &pp2800_wf_cam {
status = "okay";
};
+&usb_c0_hs {
+ remote-endpoint = <&usb_hub_dfp2_hs>;
+};
+
+&usb_c0_ss {
+ remote-endpoint = <&usb_hub_dfp2_ss>;
+};
+
+&usb_c1_hs {
+ remote-endpoint = <&usb_hub_dfp4_hs>;
+};
+
+&usb_c1_ss {
+ remote-endpoint = <&usb_hub_dfp3_ss>;
+};
+
+&usb_hub_dfp2_hs {
+ remote-endpoint = <&usb_c0_hs>;
+};
+
+&usb_hub_dfp2_ss {
+ remote-endpoint = <&usb_c0_ss>;
+};
+
+&usb_hub_dfp4_hs {
+ remote-endpoint = <&usb_c1_hs>;
+};
+
+&usb_hub_dfp3_ss {
+ remote-endpoint = <&usb_c1_ss>;
+};
+
+&usb_hub_dfp3_hs {
+ remote-endpoint = <&pogo_pins_in>;
+};
+
&wifi {
qcom,ath10k-calibration-variant = "GO_WORMDINGLER";
};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi
index 74ab321d3333..af866cdd4fef 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi
@@ -673,6 +673,25 @@ usb_c0: connector@0 {
power-role = "dual";
data-role = "host";
try-power-role = "source";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ usb_c0_hs: endpoint {
+ /* Endpoint filled in by board */
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ usb_c0_ss: endpoint {
+ /* Endpoint filled in by board */
+ };
+ };
+ };
};
usb_c1: connector@1 {
@@ -682,6 +701,25 @@ usb_c1: connector@1 {
power-role = "dual";
data-role = "host";
try-power-role = "source";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ usb_c1_hs: endpoint {
+ /* Endpoint filled in by board */
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ usb_c1_ss: endpoint {
+ /* Endpoint filled in by board */
+ };
+ };
+ };
};
};
};
@@ -966,6 +1004,41 @@ usb_hub_2_x: hub@1 {
reg = <1>;
vdd-supply = <&pp3300_hub>;
peer-hub = <&usb_hub_3_x>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usb_hub_2_x_ports: ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@1 {
+ reg = <1>;
+ usb_hub_dfp1_hs: endpoint {
+ /* Endpoint filled in by board */
+ };
+ };
+ port@2 {
+ reg = <2>;
+ usb_hub_dfp2_hs: endpoint {
+ /* Endpoint filled in by board */
+ };
+ };
+
+ port@3 {
+ reg = <3>;
+ usb_hub_dfp3_hs: endpoint {
+ /* Endpoint filled in by board */
+ };
+ };
+
+ port@4 {
+ reg = <4>;
+ usb_hub_dfp4_hs: endpoint {
+ /* Endpoint filled in by board */
+ };
+ };
+ };
};
/* 3.x hub on port 2 */
@@ -974,6 +1047,42 @@ usb_hub_3_x: hub@2 {
reg = <2>;
vdd-supply = <&pp3300_hub>;
peer-hub = <&usb_hub_2_x>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usb_hub_3_x_ports: ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@1 {
+ reg = <1>;
+ usb_hub_dfp1_ss: endpoint {
+ /* Endpoint filled in by board */
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+ usb_hub_dfp2_ss: endpoint {
+ /* Endpoint filled in by board */
+ };
+ };
+
+ port@3 {
+ reg = <3>;
+ usb_hub_dfp3_ss: endpoint {
+ /* Endpoint filled in by board */
+ };
+ };
+
+ port@4 {
+ reg = <4>;
+ usb_hub_dfp4_ss: endpoint {
+ /* Endpoint filled in by board */
+ };
+ };
+ };
};
};
--
https://chromeos.dev
prev parent reply other threads:[~2025-02-05 23:30 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-02-05 23:30 [PATCH v2 0/2] arm64: dts: qcom: sc7180-trogdor: Wire up USB Stephen Boyd
2025-02-05 23:30 ` [PATCH v2 1/2] dt-bindings: chrome: Add binding for ChromeOS Pogo pin connector Stephen Boyd
2025-02-06 11:30 ` Konrad Dybcio
2025-02-06 20:43 ` Stephen Boyd
2025-02-10 19:09 ` Konrad Dybcio
2025-02-10 22:50 ` Stephen Boyd
2025-02-05 23:30 ` Stephen Boyd [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20250205233016.1600517-3-swboyd@chromium.org \
--to=swboyd@chromium.org \
--cc=andersson@kernel.org \
--cc=conor+dt@kernel.org \
--cc=cros-qcom-dts-watchers@chromium.org \
--cc=devicetree@vger.kernel.org \
--cc=konradybcio@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=patches@lists.linux.dev \
--cc=robh@kernel.org \
--cc=treapking@chromium.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).