Re: [PATCH v6 4/4] PCI: dwc: Add support for configuring lane equalization presets

[Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>]

On Mon, Feb 10, 2025 at 01:00:03PM +0530, Krishna Chaitanya Chundru wrote:
> PCIe equalization presets are predefined settings used to optimize
> signal integrity by compensating for signal loss and distortion in
> high-speed data transmission.
> 
> Based upon the number of lanes and the data rate supported, write
> the preset data read from the device tree in to the lane equalization
> control registers.
> 
> Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
> ---
>  drivers/pci/controller/dwc/pcie-designware-host.c | 53 +++++++++++++++++++++++
>  drivers/pci/controller/dwc/pcie-designware.h      |  3 ++
>  include/uapi/linux/pci_regs.h                     |  3 ++
>  3 files changed, 59 insertions(+)
> 
> diff --git a/drivers/pci/controller/dwc/pcie-designware-host.c b/drivers/pci/controller/dwc/pcie-designware-host.c
> index dd56cc02f4ef..7d5f16f77e2f 100644
> --- a/drivers/pci/controller/dwc/pcie-designware-host.c
> +++ b/drivers/pci/controller/dwc/pcie-designware-host.c
> @@ -507,6 +507,10 @@ int dw_pcie_host_init(struct dw_pcie_rp *pp)
>  	if (pci->num_lanes < 1)
>  		pci->num_lanes = dw_pcie_link_get_max_link_width(pci);
>  
> +	ret = of_pci_get_equalization_presets(dev, &pp->presets, pci->num_lanes);
> +	if (ret)
> +		goto err_free_msi;
> +
>  	/*
>  	 * Allocate the resource for MSG TLP before programming the iATU
>  	 * outbound window in dw_pcie_setup_rc(). Since the allocation depends
> @@ -808,6 +812,54 @@ static int dw_pcie_iatu_setup(struct dw_pcie_rp *pp)
>  	return 0;
>  }
>  
> +static void dw_pcie_program_presets(struct dw_pcie_rp *pp, enum pci_bus_speed speed)
> +{
> +	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
> +	u8 lane_eq_offset, lane_reg_size, cap_id;
> +	u8 *presets;
> +	u32 cap;
> +	int i;
> +
> +	if (speed == PCIE_SPEED_8_0GT) {
> +		presets = (u8 *)pp->presets.eq_presets_8gts;
> +		lane_eq_offset =  PCI_SECPCI_LE_CTRL;
> +		cap_id = PCI_EXT_CAP_ID_SECPCI;
> +		/* For data rate of 8 GT/S each lane equalization control is 16bits wide*/
> +		lane_reg_size = 0x2;
> +	} else if (speed == PCIE_SPEED_16_0GT) {
> +		presets = pp->presets.eq_presets_Ngts[EQ_PRESET_TYPE_16GTS];
> +		lane_eq_offset = PCI_PL_16GT_LE_CTRL;
> +		cap_id = PCI_EXT_CAP_ID_PL_16GT;
> +		lane_reg_size = 0x1;
> +	}
> +
> +	if (presets[0] == PCI_EQ_RESV)
> +		return;
> +
> +	cap = dw_pcie_find_ext_capability(pci, cap_id);
> +	if (!cap)
> +		return;
> +
> +	/*
> +	 * Write preset values to the registers byte-by-byte for the given
> +	 * number of lanes and register size.
> +	 */
> +	for (i = 0; i < pci->num_lanes * lane_reg_size; i++)
> +		dw_pcie_writeb_dbi(pci, cap + lane_eq_offset + i, presets[i]);
> +}
> +
> +static void dw_pcie_config_presets(struct dw_pcie_rp *pp)
> +{
> +	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
> +	enum pci_bus_speed speed = pcie_link_speed[pci->max_link_speed];
> +

Please add a comment stating that the equalization needs to be performed at all
lower data rates for each lane.

> +	if (speed >= PCIE_SPEED_8_0GT)
> +		dw_pcie_program_presets(pp, PCIE_SPEED_8_0GT);
> +
> +	if (speed >= PCIE_SPEED_16_0GT)
> +		dw_pcie_program_presets(pp, PCIE_SPEED_16_0GT);

I think we need to check 'Link Equalization Request' before performing
equalization? This will also help us to warn users if they didn't specify the
property in DT if hardware expects equalization.

Currently, even if DT specifies equalization presets for 32GT/s, driver is not
making use of them.

- Mani

-- 
மணிவண்ணன் சதாசிவம்