[PATCH PATCH RFC NOT TESTED 1/2] ARM: dts: ti: dra7: Correct ranges for PCIe and parent bus nodes

[Frank Li <Frank.Li@nxp.com>]

According to code in drivers/pci/controller/dwc/pci-dra7xx.c

dra7xx_pcie_cpu_addr_fixup()
{
	return cpu_addr & DRA7XX_CPU_TO_BUS_ADDR;  //0x0FFFFFFF
}

PCI parent bus trim high 4 bits address to 0. Correct ranges in
target-module@51000000 to algin hardware behavior, which translate PCIe
outbound address 0..0x0fff_ffff to 0x2000_0000..0x2fff_ffff.

Set 'config' and 'addr_space' reg values to 0.
Change parent bus address of downstream I/O and non-prefetchable memory to
0.

Ensure no functional impact on the final address translation result.

Prepare for the removal of the driver’s cpu_addr_fixup().

Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
 arch/arm/boot/dts/ti/omap/dra7.dtsi | 18 +++++++++---------
 1 file changed, 9 insertions(+), 9 deletions(-)

diff --git a/arch/arm/boot/dts/ti/omap/dra7.dtsi b/arch/arm/boot/dts/ti/omap/dra7.dtsi
index b709703f6c0d4..9213fdd25330b 100644
--- a/arch/arm/boot/dts/ti/omap/dra7.dtsi
+++ b/arch/arm/boot/dts/ti/omap/dra7.dtsi
@@ -196,7 +196,7 @@ axi0: target-module@51000000 {
 			#size-cells = <1>;
 			#address-cells = <1>;
 			ranges = <0x51000000 0x51000000 0x3000>,
-				 <0x20000000 0x20000000 0x10000000>;
+				 <0x00000000 0x20000000 0x10000000>;
 			dma-ranges;
 			/**
 			 * To enable PCI endpoint mode, disable the pcie1_rc
@@ -205,14 +205,14 @@ axi0: target-module@51000000 {
 			pcie1_rc: pcie@51000000 {
 				reg = <0x51000000 0x2000>,
 				      <0x51002000 0x14c>,
-				      <0x20001000 0x2000>;
+				      <0x00001000 0x2000>;
 				reg-names = "rc_dbics", "ti_conf", "config";
 				interrupts = <0 232 0x4>, <0 233 0x4>;
 				#address-cells = <3>;
 				#size-cells = <2>;
 				device_type = "pci";
-				ranges = <0x81000000 0 0x00000000 0x20003000 0 0x00010000>,
-					 <0x82000000 0 0x20013000 0x20013000 0 0x0ffed000>;
+				ranges = <0x81000000 0 0x00000000 0x00003000 0 0x00010000>,
+					 <0x82000000 0 0x20013000 0x00013000 0 0x0ffed000>;
 				bus-range = <0x00 0xff>;
 				#interrupt-cells = <1>;
 				num-lanes = <1>;
@@ -238,7 +238,7 @@ pcie1_ep: pcie_ep@51000000 {
 				reg = <0x51000000 0x28>,
 				      <0x51002000 0x14c>,
 				      <0x51001000 0x28>,
-				      <0x20001000 0x10000000>;
+				      <0x00001000 0x10000000>;
 				reg-names = "ep_dbics", "ti_conf", "ep_dbics2", "addr_space";
 				interrupts = <0 232 0x4>;
 				num-lanes = <1>;
@@ -270,20 +270,20 @@ axi1: target-module@51800000 {
 			#size-cells = <1>;
 			#address-cells = <1>;
 			ranges = <0x51800000 0x51800000 0x3000>,
-				 <0x30000000 0x30000000 0x10000000>;
+				 <0x00000000 0x30000000 0x10000000>;
 			dma-ranges;
 			status = "disabled";
 			pcie2_rc: pcie@51800000 {
 				reg = <0x51800000 0x2000>,
 				      <0x51802000 0x14c>,
-				      <0x30001000 0x2000>;
+				      <0x00001000 0x2000>;
 				reg-names = "rc_dbics", "ti_conf", "config";
 				interrupts = <0 355 0x4>, <0 356 0x4>;
 				#address-cells = <3>;
 				#size-cells = <2>;
 				device_type = "pci";
-				ranges = <0x81000000 0 0x00000000 0x30003000 0 0x00010000>,
-					 <0x82000000 0 0x30013000 0x30013000 0 0x0ffed000>;
+				ranges = <0x81000000 0 0x00000000 0x00003000 0 0x00010000>,
+					 <0x82000000 0 0x30013000 0x00013000 0 0x0ffed000>;
 				bus-range = <0x00 0xff>;
 				#interrupt-cells = <1>;
 				num-lanes = <1>;

-- 
2.34.1