From: Aleksandrs Vinarskis <alex.vinarskis@gmail.com>
To: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com>,
linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org
Cc: Bjorn Andersson <andersson@kernel.org>,
Konrad Dybcio <konradybcio@kernel.org>,
Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>,
laurentiu.tudor1@dell.com, dmitry.baryshkov@oss.qualcomm.com,
Aleksandrs Vinarskis <alex.vinarskis@gmail.com>
Subject: [PATCH v2 1/1] arm64: dts: qcom: x1e80100-dell-xps-9345: Add WiFi/BT pwrseq
Date: Mon, 31 Mar 2025 08:33:47 +0100 [thread overview]
Message-ID: <20250331073423.3184322-2-alex.vinarskis@gmail.com> (raw)
In-Reply-To: <20250331073423.3184322-1-alex.vinarskis@gmail.com>
Add the WiFi/BT nodes for XPS and describe the regulators for the WCN7850
combo chip using the new power sequencing bindings. All voltages are
derived from chained fixed regulators controlled using a single GPIO.
Based on the commit d09ab685a8f5 ("arm64: dts: qcom: x1e80100-qcp: Add
WiFi/BT pwrseq").
With that fixed commit f5b788d0e8cd ("arm64: dts: qcom: Add support for
X1-based Dell XPS 13 9345")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Aleksandrs Vinarskis <alex.vinarskis@gmail.com>
---
.../dts/qcom/x1e80100-dell-xps13-9345.dts | 144 ++++++++++++++++++
1 file changed, 144 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/x1e80100-dell-xps13-9345.dts b/arch/arm64/boot/dts/qcom/x1e80100-dell-xps13-9345.dts
index d259a0d12d7b..c924f2a67939 100644
--- a/arch/arm64/boot/dts/qcom/x1e80100-dell-xps13-9345.dts
+++ b/arch/arm64/boot/dts/qcom/x1e80100-dell-xps13-9345.dts
@@ -22,6 +22,7 @@ / {
aliases {
serial0 = &uart21;
+ serial1 = &uart14;
};
gpio-keys {
@@ -288,6 +289,101 @@ vreg_vph_pwr: regulator-vph-pwr {
regulator-always-on;
regulator-boot-on;
};
+
+ vreg_wcn_0p95: regulator-wcn-0p95 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_WCN_0P95";
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <950000>;
+
+ vin-supply = <&vreg_wcn_3p3>;
+ };
+
+ vreg_wcn_1p9: regulator-wcn-1p9 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_WCN_1P9";
+ regulator-min-microvolt = <1900000>;
+ regulator-max-microvolt = <1900000>;
+
+ vin-supply = <&vreg_wcn_3p3>;
+ };
+
+ vreg_wcn_3p3: regulator-wcn-3p3 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_WCN_3P3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&tlmm 214 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&wcn_sw_en>;
+ pinctrl-names = "default";
+
+ regulator-boot-on;
+ };
+
+ wcn7850-pmu {
+ compatible = "qcom,wcn7850-pmu";
+
+ vdd-supply = <&vreg_wcn_0p95>;
+ vddio-supply = <&vreg_l15b_1p8>;
+ vddaon-supply = <&vreg_wcn_0p95>;
+ vdddig-supply = <&vreg_wcn_0p95>;
+ vddrfa1p2-supply = <&vreg_wcn_1p9>;
+ vddrfa1p8-supply = <&vreg_wcn_1p9>;
+
+ wlan-enable-gpios = <&tlmm 117 GPIO_ACTIVE_HIGH>;
+ bt-enable-gpios = <&tlmm 116 GPIO_ACTIVE_HIGH>;
+
+ pinctrl-0 = <&wcn_wlan_bt_en>;
+ pinctrl-names = "default";
+
+ regulators {
+ vreg_pmu_rfa_cmn: ldo0 {
+ regulator-name = "vreg_pmu_rfa_cmn";
+ };
+
+ vreg_pmu_aon_0p59: ldo1 {
+ regulator-name = "vreg_pmu_aon_0p59";
+ };
+
+ vreg_pmu_wlcx_0p8: ldo2 {
+ regulator-name = "vreg_pmu_wlcx_0p8";
+ };
+
+ vreg_pmu_wlmx_0p85: ldo3 {
+ regulator-name = "vreg_pmu_wlmx_0p85";
+ };
+
+ vreg_pmu_btcmx_0p85: ldo4 {
+ regulator-name = "vreg_pmu_btcmx_0p85";
+ };
+
+ vreg_pmu_rfa_0p8: ldo5 {
+ regulator-name = "vreg_pmu_rfa_0p8";
+ };
+
+ vreg_pmu_rfa_1p2: ldo6 {
+ regulator-name = "vreg_pmu_rfa_1p2";
+ };
+
+ vreg_pmu_rfa_1p8: ldo7 {
+ regulator-name = "vreg_pmu_rfa_1p8";
+ };
+
+ vreg_pmu_pcie_0p9: ldo8 {
+ regulator-name = "vreg_pmu_pcie_0p9";
+ };
+
+ vreg_pmu_pcie_1p8: ldo9 {
+ regulator-name = "vreg_pmu_pcie_1p8";
+ };
+ };
+ };
};
&apps_rsc {
@@ -861,6 +957,23 @@ &pcie4_phy {
status = "okay";
};
+&pcie4_port0 {
+ wifi@0 {
+ compatible = "pci17cb,1107";
+ reg = <0x10000 0x0 0x0 0x0 0x0>;
+
+ vddaon-supply = <&vreg_pmu_aon_0p59>;
+ vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+ vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
+ vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+ vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+ vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+ vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>;
+ vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>;
+ vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>;
+ };
+};
+
&pcie6a {
perst-gpios = <&tlmm 152 GPIO_ACTIVE_LOW>;
wake-gpios = <&tlmm 154 GPIO_ACTIVE_LOW>;
@@ -1127,6 +1240,37 @@ reset-n-pins {
drive-strength = <2>;
};
};
+
+ wcn_wlan_bt_en: wcn-wlan-bt-en-state {
+ pins = "gpio116", "gpio117";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ wcn_sw_en: wcn-sw-en-state {
+ pins = "gpio214";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+};
+
+&uart14 {
+ status = "okay";
+
+ bluetooth {
+ compatible = "qcom,wcn7850-bt";
+ max-speed = <3200000>;
+
+ vddaon-supply = <&vreg_pmu_aon_0p59>;
+ vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+ vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
+ vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+ vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+ vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+ vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>;
+ };
};
&uart21 {
--
2.45.2
next prev parent reply other threads:[~2025-03-31 7:34 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-03-31 7:33 [PATCH v2 0/1] arm64: dts: qcom: x1e80100-dell-xps-9345: Add WiFi/BT pwrseq Aleksandrs Vinarskis
2025-03-31 7:33 ` Aleksandrs Vinarskis [this message]
2025-03-31 8:09 ` [PATCH v2 1/1] " Johan Hovold
2025-03-31 9:38 ` Aleksandrs Vinarskis
2025-03-31 11:00 ` Johan Hovold
2025-03-31 16:51 ` Aleksandrs Vinarskis
2025-03-31 19:06 ` Johan Hovold
2025-03-31 20:15 ` Dmitry Baryshkov
2025-03-31 20:27 ` Aleksandrs Vinarskis
2025-03-31 8:33 ` Bryan O'Donoghue
2025-03-31 9:40 ` Aleksandrs Vinarskis
2025-03-31 13:22 ` Tudor, Laurentiu
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20250331073423.3184322-2-alex.vinarskis@gmail.com \
--to=alex.vinarskis@gmail.com \
--cc=andersson@kernel.org \
--cc=bjorn.andersson@oss.qualcomm.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=dmitry.baryshkov@oss.qualcomm.com \
--cc=konradybcio@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=laurentiu.tudor1@dell.com \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox