[PATCH v2 12/17] dt-bindings: arm/cpus: Add schemas for "enable-method" dependencies

["Rob Herring (Arm)" <robh@kernel.org>]

Replace the prose for properties dependent on specific "enable-method"
values with schemas defining the same requirements.

Both "qcom,acc" and "qcom,saw" properties appear to be required for any
of the Qualcomm enable-method values, so the schema is a bit simpler
than what the text said. The properties are also needed on some Qualcomm
platforms with other enable-method values. It's limited to Cortex A53
based platforms so use that to disable the properties. The references
to arm/msm/qcom,saw2.txt and arm/msm/qcom,kpss-acc.txt are out of date,
so just drop them.

Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
---
v2:
 - Only disallow qcom,acc and qcom,saw on !cortex-a53
 - Fix example in qcom,saw2.yaml
---
 Documentation/devicetree/bindings/arm/cpus.yaml    | 91 ++++++++++++++--------
 .../devicetree/bindings/soc/qcom/qcom,saw2.yaml    |  3 +-
 2 files changed, 60 insertions(+), 34 deletions(-)

diff --git a/Documentation/devicetree/bindings/arm/cpus.yaml b/Documentation/devicetree/bindings/arm/cpus.yaml
index 2e666b2a4dcd..351be2f77581 100644
--- a/Documentation/devicetree/bindings/arm/cpus.yaml
+++ b/Documentation/devicetree/bindings/arm/cpus.yaml
@@ -273,8 +273,6 @@ properties:
     description:
       The DT specification defines this as 64-bit always, but some 32-bit Arm
       systems have used a 32-bit value which must be supported.
-      Required for systems that have an "enable-method"
-        property value of "spin-table".
 
   cpu-idle-states:
     $ref: /schemas/types.yaml#/definitions/phandle-array
@@ -333,24 +331,13 @@ properties:
 
   qcom,saw:
     $ref: /schemas/types.yaml#/definitions/phandle
-    description: |
-      Specifies the SAW* node associated with this CPU.
-
-      Required for systems that have an "enable-method" property
-      value of "qcom,kpss-acc-v1" or "qcom,kpss-acc-v2"
-
-      * arm/msm/qcom,saw2.txt
+    description:
+      Specifies the SAW node associated with this CPU.
 
   qcom,acc:
     $ref: /schemas/types.yaml#/definitions/phandle
-    description: |
-      Specifies the ACC* node associated with this CPU.
-
-      Required for systems that have an "enable-method" property
-      value of "qcom,kpss-acc-v1", "qcom,kpss-acc-v2", "qcom,msm8226-smp" or
-      "qcom,msm8916-smp".
-
-      * arm/msm/qcom,kpss-acc.txt
+    description:
+      Specifies the ACC node associated with this CPU.
 
   rockchip,pmu:
     $ref: /schemas/types.yaml#/definitions/phandle
@@ -378,22 +365,60 @@ properties:
       formed by encoding the target CPU id into the low bits of the
       physical start address it should jump to.
 
-if:
-  # If the enable-method property contains one of those values
-  properties:
-    enable-method:
-      contains:
-        enum:
-          - brcm,bcm11351-cpu-method
-          - brcm,bcm23550
-          - brcm,bcm-nsp-smp
-  # and if enable-method is present
-  required:
-    - enable-method
-
-then:
-  required:
-    - secondary-boot-reg
+allOf:
+  - if:
+      # If the enable-method property contains one of those values
+      properties:
+        enable-method:
+          contains:
+            enum:
+              - brcm,bcm11351-cpu-method
+              - brcm,bcm23550
+              - brcm,bcm-nsp-smp
+      # and if enable-method is present
+      required:
+        - enable-method
+    then:
+      required:
+        - secondary-boot-reg
+  - if:
+      properties:
+        enable-method:
+          enum:
+            - spin-table
+            - renesas,r9a06g032-smp
+      required:
+        - enable-method
+    then:
+      required:
+        - cpu-release-addr
+  - if:
+      properties:
+        enable-method:
+          enum:
+            - qcom,kpss-acc-v1
+            - qcom,kpss-acc-v2
+            - qcom,msm8226-smp
+            - qcom,msm8916-smp
+      required:
+        - enable-method
+    then:
+      required:
+        - qcom,acc
+        - qcom,saw
+  - if:
+      # 2 Qualcomm platforms bootloaders need qcom,acc and qcom,saw yet use
+      # "spin-table" or "psci" enable-methods. Disallowing the properties for
+      # all other CPUs is the best we can do as there's not any way to
+      # distinguish these Qualcomm platforms.
+      not:
+        properties:
+          compatible:
+            const: arm,cortex-a53
+    then:
+      properties:
+        qcom,acc: false
+        qcom,saw: false
 
 required:
   - device_type
diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,saw2.yaml b/Documentation/devicetree/bindings/soc/qcom/qcom,saw2.yaml
index ca4bce817273..c2f1f5946cfa 100644
--- a/Documentation/devicetree/bindings/soc/qcom/qcom,saw2.yaml
+++ b/Documentation/devicetree/bindings/soc/qcom/qcom,saw2.yaml
@@ -73,9 +73,10 @@ examples:
         #size-cells = <0>;
 
         cpu@0 {
-            compatible = "qcom,kryo";
+            compatible = "arm,cortex-a53";
             device_type = "cpu";
             enable-method = "qcom,kpss-acc-v2";
+            qcom,acc = <&acc0>;
             qcom,saw = <&saw0>;
             reg = <0x0>;
             operating-points-v2 = <&cpu_opp_table>;

-- 
2.47.2