public inbox for devicetree@vger.kernel.org
 help / color / mirror / Atom feed
From: Chaoyi Chen <kernel@airkyi.com>
To: Heiko Stuebner <heiko@sntech.de>
Cc: Rob Herring <robh@kernel.org>,
	Krzysztof Kozlowski <krzk+dt@kernel.org>,
	Conor Dooley <conor+dt@kernel.org>,
	Jonas Karlman <jonas@kwiboo.se>,
	Kever Yang <kever.yang@rock-chips.com>,
	Jianfeng Liu <liujianfeng1994@gmail.com>,
	Dragan Simic <dsimic@manjaro.org>,
	Jimmy Hon <honyuenkwun@gmail.com>,
	Quentin Schulz <quentin.schulz@cherry.de>,
	FUKAUMI Naoki <naoki@radxa.com>,
	Cristian Ciocaltea <cristian.ciocaltea@collabora.com>,
	Alexey Charkov <alchark@gmail.com>,
	Geert Uytterhoeven <geert+renesas@glider.be>,
	Sebastian Reichel <sebastian.reichel@collabora.com>,
	Chaoyi Chen <chaoyi.chen@rock-chips.com>,
	devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
	linux-rockchip@lists.infradead.org, linux-kernel@vger.kernel.org
Subject: [PATCH 2/2] arm64: dts: rockchip: Add rk3399-evb-ind board
Date: Sun, 27 Apr 2025 17:42:11 +0800	[thread overview]
Message-ID: <20250427094211.246-3-kernel@airkyi.com> (raw)
In-Reply-To: <20250427094211.246-1-kernel@airkyi.com>

From: Chaoyi Chen <chaoyi.chen@rock-chips.com>

General feature for rk3399 industry evaluation board:
- Rockchip RK3399
- 4GB LPDDR4
- emmc5.1
- SDIO3.0 compatible TF card
- 1x HDMI2.0a TX
- 1x HDMI1.4b RX with TC358749XBG HDMI to MIPI CSI2 bridge chip
- 1x type-c DisplayPort
- 3x USB3.0 Host
- 1x USB2.0 Host
- 1x Ethernet / USB3.0 to Ethernet

Tested with HDMI/GPU/USB2.0/USB3.0/Ethernet/TF card/emmc.

Signed-off-by: Chaoyi Chen <chaoyi.chen@rock-chips.com>
---
 arch/arm64/boot/dts/rockchip/Makefile         |   1 +
 .../boot/dts/rockchip/rk3399-evb-ind.dts      | 222 ++++++++++++++++++
 2 files changed, 223 insertions(+)
 create mode 100644 arch/arm64/boot/dts/rockchip/rk3399-evb-ind.dts

diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index 3e8771ef69ba..8a3adb7482ca 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -40,6 +40,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-px5-evb.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-r88.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-eaidk-610.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-evb.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-evb-ind.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-ficus.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-firefly.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-gru-bob.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-evb-ind.dts b/arch/arm64/boot/dts/rockchip/rk3399-evb-ind.dts
new file mode 100644
index 000000000000..a995d4ff202d
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3399-evb-ind.dts
@@ -0,0 +1,222 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2025 Rockchip Electronics Co., Ltd.
+ */
+
+/dts-v1/;
+#include "rk3399-base.dtsi"
+
+/ {
+	model = "Rockchip RK3399 EVB IND LPDDR4 Board";
+	compatible = "rockchip,rk3399-evb-ind", "rockchip,rk3399";
+
+	aliases {
+		ethernet0 = &gmac;
+		mmc0 = &sdhci;
+		mmc1 = &sdmmc;
+	};
+
+	chosen {
+		stdout-path = "serial2:1500000n8";
+	};
+
+	clkin_gmac: external-gmac-clock {
+		compatible = "fixed-clock";
+		clock-frequency = <125000000>;
+		clock-output-names = "clkin_gmac";
+		#clock-cells = <0>;
+	};
+
+	vcc5v0_sys: regulator-vcc5v0-sys {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio4 RK_PD2 GPIO_ACTIVE_HIGH>;
+		regulator-name = "vcc5v0_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+	};
+
+	vcc_phy: regulator-vcc-phy {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-name = "vcc_phy";
+	};
+};
+
+&emmc_phy {
+	status = "okay";
+};
+
+&gmac {
+	assigned-clocks = <&cru SCLK_RMII_SRC>;
+	assigned-clock-parents = <&clkin_gmac>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii_pins>;
+	clock_in_out = "input";
+	phy-supply = <&vcc_phy>;
+	phy-mode = "rgmii";
+	snps,reset-gpio = <&gpio3 RK_PB7 GPIO_ACTIVE_LOW>;
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 10000 150000>;
+	tx_delay = <0x22>;
+	rx_delay = <0x23>;
+	status = "okay";
+};
+
+&gpu {
+	mali-supply = <&vdd_gpu>;
+	status = "okay";
+};
+
+&hdmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hdmi_i2c_xfer>, <&hdmi_cec>;
+	status = "okay";
+};
+
+&hdmi_in_vopl {
+	status = "disabled";
+};
+
+&hdmi_sound {
+	status = "okay";
+};
+
+&i2c0 {
+	clock-frequency = <400000>;
+	i2c-scl-falling-time-ns = <4>;
+	i2c-scl-rising-time-ns = <168>;
+	status = "okay";
+
+	vdd_gpu: tcs4526@10 {
+		compatible = "tcs,tcs4525";
+		reg = <0x10>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vsel2_gpio>;
+		fcs,suspend-voltage-selector = <1>;
+		vin-supply = <&vcc5v0_sys>;
+		vsel-gpios = <&gpio1 RK_PB6 GPIO_ACTIVE_HIGH>;
+		regulator-compatible = "fan53555-reg";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-initial-state = <3>;
+		regulator-max-microvolt = <1500000>;
+		regulator-min-microvolt = <712500>;
+		regulator-name = "vdd_gpu";
+		regulator-ramp-delay = <1000>;
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+};
+
+&sdmmc {
+	bus-width = <4>;
+	cap-mmc-highspeed;
+	cap-sd-highspeed;
+	cd-gpios = <&gpio0 RK_PA7 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	max-frequency = <150000000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_bus4>;
+	status = "okay";
+};
+
+&sdhci {
+	bus-width = <8>;
+	keep-power-in-suspend;
+	mmc-hs400-1_8v;
+	mmc-hs400-enhanced-strobe;
+	no-sdio;
+	no-sd;
+	non-removable;
+	status = "okay";
+};
+
+&tcphy0 {
+	status = "okay";
+};
+
+&tcphy1 {
+	status = "okay";
+};
+
+&u2phy0 {
+	status = "okay";
+};
+
+&u2phy0_host {
+	status = "okay";
+};
+
+&u2phy0_otg {
+	status = "okay";
+};
+
+&u2phy1 {
+	status = "okay";
+};
+
+&u2phy1_host {
+	status = "okay";
+};
+
+&u2phy1_otg {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&usbdrd_dwc3_0 {
+	status = "okay";
+};
+
+&usbdrd3_0 {
+	status = "okay";
+};
+
+&usbdrd3_1 {
+	status = "okay";
+};
+
+&usbdrd_dwc3_1 {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usb_host0_ehci {
+	status = "okay";
+};
+
+&usb_host0_ohci {
+	status = "okay";
+};
+
+&usb_host1_ehci {
+	status = "okay";
+};
+
+&usb_host1_ohci {
+	status = "okay";
+};
+
+&pinctrl {
+	pmic {
+		vsel2_gpio: vsel2-gpio {
+			rockchip,pins = <1 RK_PB6 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+	};
+};
+
+&vopb {
+	status = "okay";
+};
+
+&vopb_mmu {
+	status = "okay";
+};
-- 
2.49.0


  parent reply	other threads:[~2025-04-27  9:43 UTC|newest]

Thread overview: 12+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2025-04-27  9:42 [PATCH 0/2] Add support for rk3399 industry evaluation board Chaoyi Chen
2025-04-27  9:42 ` [PATCH 1/2] dt-bindings: arm: rockchip: Add " Chaoyi Chen
2025-04-30 10:22   ` Krzysztof Kozlowski
2025-04-27  9:42 ` Chaoyi Chen [this message]
2025-04-27 20:42   ` [PATCH 2/2] arm64: dts: rockchip: Add rk3399-evb-ind board Andrew Lunn
2025-04-28  1:47     ` Chaoyi Chen
2025-04-28 12:45       ` Andrew Lunn
2025-04-29  2:42         ` Chaoyi Chen
2025-04-29 12:22           ` Andrew Lunn
2025-04-30  2:03             ` Chaoyi Chen
2025-04-28  8:19   ` Quentin Schulz
2025-04-28 10:01     ` Chaoyi Chen

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20250427094211.246-3-kernel@airkyi.com \
    --to=kernel@airkyi.com \
    --cc=alchark@gmail.com \
    --cc=chaoyi.chen@rock-chips.com \
    --cc=conor+dt@kernel.org \
    --cc=cristian.ciocaltea@collabora.com \
    --cc=devicetree@vger.kernel.org \
    --cc=dsimic@manjaro.org \
    --cc=geert+renesas@glider.be \
    --cc=heiko@sntech.de \
    --cc=honyuenkwun@gmail.com \
    --cc=jonas@kwiboo.se \
    --cc=kever.yang@rock-chips.com \
    --cc=krzk+dt@kernel.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-rockchip@lists.infradead.org \
    --cc=liujianfeng1994@gmail.com \
    --cc=naoki@radxa.com \
    --cc=quentin.schulz@cherry.de \
    --cc=robh@kernel.org \
    --cc=sebastian.reichel@collabora.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox