[PATCH v5 18/24] drm/msm/dsi/phy: Add support for SM8750

[Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>]

Add support for DSI PHY v7.0 on Qualcomm SM8750 SoC which comes with an
incompatible hardware interface change:

ICODE_ACCUM_STATUS_LOW and ALOG_OBSV_BUS_STATUS_1 registers - their
offsets were just switched.  Currently these registers are not used in
the driver, so the easiest is to document both but keep them commented
out to avoid conflict.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---

Changes in v2:
1. Fix pll freq check for clock inverters
   160000000ULL -> 163000000ULL
---
 drivers/gpu/drm/msm/dsi/phy/dsi_phy.c              |  2 +
 drivers/gpu/drm/msm/dsi/phy/dsi_phy.h              |  1 +
 drivers/gpu/drm/msm/dsi/phy/dsi_phy_7nm.c          | 79 ++++++++++++++++++++--
 .../gpu/drm/msm/registers/display/dsi_phy_7nm.xml  | 14 ++++
 4 files changed, 90 insertions(+), 6 deletions(-)

diff --git a/drivers/gpu/drm/msm/dsi/phy/dsi_phy.c b/drivers/gpu/drm/msm/dsi/phy/dsi_phy.c
index c0bcc68289633fd7506ce4f1f963655d862e8f08..60571237efc4d332959ac76ff1d6d6245f688469 100644
--- a/drivers/gpu/drm/msm/dsi/phy/dsi_phy.c
+++ b/drivers/gpu/drm/msm/dsi/phy/dsi_phy.c
@@ -593,6 +593,8 @@ static const struct of_device_id dsi_phy_dt_match[] = {
 	  .data = &dsi_phy_4nm_8550_cfgs },
 	{ .compatible = "qcom,sm8650-dsi-phy-4nm",
 	  .data = &dsi_phy_4nm_8650_cfgs },
+	{ .compatible = "qcom,sm8750-dsi-phy-3nm",
+	  .data = &dsi_phy_3nm_8750_cfgs },
 #endif
 	{}
 };
diff --git a/drivers/gpu/drm/msm/dsi/phy/dsi_phy.h b/drivers/gpu/drm/msm/dsi/phy/dsi_phy.h
index 7aac0c6ebb37ba15d7af59c28cd9494752d9fdbb..a9fedc4cdc9f87bbab890cd4c3acc8df50a3a60c 100644
--- a/drivers/gpu/drm/msm/dsi/phy/dsi_phy.h
+++ b/drivers/gpu/drm/msm/dsi/phy/dsi_phy.h
@@ -61,6 +61,7 @@ extern const struct msm_dsi_phy_cfg dsi_phy_5nm_8350_cfgs;
 extern const struct msm_dsi_phy_cfg dsi_phy_5nm_8450_cfgs;
 extern const struct msm_dsi_phy_cfg dsi_phy_4nm_8550_cfgs;
 extern const struct msm_dsi_phy_cfg dsi_phy_4nm_8650_cfgs;
+extern const struct msm_dsi_phy_cfg dsi_phy_3nm_8750_cfgs;
 
 struct msm_dsi_dphy_timing {
 	u32 clk_zero;
diff --git a/drivers/gpu/drm/msm/dsi/phy/dsi_phy_7nm.c b/drivers/gpu/drm/msm/dsi/phy/dsi_phy_7nm.c
index 9c7df9e00e027e8a8b1daad7c11dcfeeea52ca9d..9e4ed75dfec8b7838d78e9db8fa67e4c5a8ec27c 100644
--- a/drivers/gpu/drm/msm/dsi/phy/dsi_phy_7nm.c
+++ b/drivers/gpu/drm/msm/dsi/phy/dsi_phy_7nm.c
@@ -51,6 +51,8 @@
 #define DSI_PHY_7NM_QUIRK_V4_3		BIT(3)
 /* Hardware is V5.2 */
 #define DSI_PHY_7NM_QUIRK_V5_2		BIT(4)
+/* Hardware is V7.0 */
+#define DSI_PHY_7NM_QUIRK_V7_0		BIT(5)
 
 struct dsi_pll_config {
 	bool enable_ssc;
@@ -139,9 +141,30 @@ static void dsi_pll_calc_dec_frac(struct dsi_pll_7nm *pll, struct dsi_pll_config
 	dec_multiple = div_u64(pll_freq * multiplier, divider);
 	dec = div_u64_rem(dec_multiple, multiplier, &frac);
 
-	if (pll->phy->cfg->quirks & DSI_PHY_7NM_QUIRK_PRE_V4_1)
+	if (pll->phy->cfg->quirks & DSI_PHY_7NM_QUIRK_PRE_V4_1) {
 		config->pll_clock_inverters = 0x28;
-	else if ((pll->phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V5_2)) {
+	} else if ((pll->phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V7_0)) {
+		if (pll_freq < 163000000ULL)
+			config->pll_clock_inverters = 0xa0;
+		else if (pll_freq < 175000000ULL)
+			config->pll_clock_inverters = 0x20;
+		else if (pll_freq < 325000000ULL)
+			config->pll_clock_inverters = 0xa0;
+		else if (pll_freq < 350000000ULL)
+			config->pll_clock_inverters = 0x20;
+		else if (pll_freq < 650000000ULL)
+			config->pll_clock_inverters = 0xa0;
+		else if (pll_freq < 700000000ULL)
+			config->pll_clock_inverters = 0x20;
+		else if (pll_freq < 1300000000ULL)
+			config->pll_clock_inverters = 0xa0;
+		else if (pll_freq < 2500000000ULL)
+			config->pll_clock_inverters = 0x20;
+		else if (pll_freq < 4000000000ULL)
+			config->pll_clock_inverters = 0x00;
+		else
+			config->pll_clock_inverters = 0x40;
+	} else if ((pll->phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V5_2)) {
 		if (pll_freq <= 1300000000ULL)
 			config->pll_clock_inverters = 0xa0;
 		else if (pll_freq <= 2500000000ULL)
@@ -260,7 +283,8 @@ static void dsi_pll_config_hzindep_reg(struct dsi_pll_7nm *pll)
 			vco_config_1 = 0x01;
 	}
 
-	if ((pll->phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V5_2)) {
+	if ((pll->phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V5_2) ||
+	    (pll->phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V7_0)) {
 		if (pll->vco_current_rate < 1557000000ULL)
 			vco_config_1 = 0x08;
 		else
@@ -668,6 +692,7 @@ static int dsi_7nm_pll_restore_state(struct msm_dsi_phy *phy)
 static int dsi_7nm_set_usecase(struct msm_dsi_phy *phy)
 {
 	struct dsi_pll_7nm *pll_7nm = to_pll_7nm(phy->vco_hw);
+	void __iomem *base = phy->base;
 	u32 data = 0x0;	/* internal PLL */
 
 	DBG("DSI PLL%d", pll_7nm->phy->id);
@@ -677,6 +702,9 @@ static int dsi_7nm_set_usecase(struct msm_dsi_phy *phy)
 		break;
 	case MSM_DSI_PHY_MASTER:
 		pll_7nm->slave = pll_7nm_list[(pll_7nm->phy->id + 1) % DSI_MAX];
+		/* v7.0: Enable ATB_EN0 and alternate clock output to external phy */
+		if (phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V7_0)
+			writel(0x07, base + REG_DSI_7nm_PHY_CMN_CTRL_5);
 		break;
 	case MSM_DSI_PHY_SLAVE:
 		data = 0x1; /* external PLL */
@@ -965,7 +993,8 @@ static int dsi_7nm_phy_enable(struct msm_dsi_phy *phy,
 
 	/* Request for REFGEN READY */
 	if ((phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V4_3) ||
-	    (phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V5_2)) {
+	    (phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V5_2) ||
+	    (phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V7_0)) {
 		writel(0x1, phy->base + REG_DSI_7nm_PHY_CMN_GLBL_DIGTOP_SPARE10);
 		udelay(500);
 	}
@@ -999,7 +1028,20 @@ static int dsi_7nm_phy_enable(struct msm_dsi_phy *phy,
 		lane_ctrl0 = 0x1f;
 	}
 
-	if ((phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V5_2)) {
+	if ((phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V7_0)) {
+		if (phy->cphy_mode) {
+			/* TODO: different for second phy */
+			vreg_ctrl_0 = 0x57;
+			vreg_ctrl_1 = 0x41;
+			glbl_rescode_top_ctrl = 0x3d;
+			glbl_rescode_bot_ctrl = 0x38;
+		} else {
+			vreg_ctrl_0 = 0x56;
+			vreg_ctrl_1 = 0x19;
+			glbl_rescode_top_ctrl = less_than_1500_mhz ? 0x3c :  0x03;
+			glbl_rescode_bot_ctrl = less_than_1500_mhz ? 0x38 :  0x3c;
+		}
+	} else if ((phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V5_2)) {
 		if (phy->cphy_mode) {
 			vreg_ctrl_0 = 0x45;
 			vreg_ctrl_1 = 0x41;
@@ -1065,6 +1107,7 @@ static int dsi_7nm_phy_enable(struct msm_dsi_phy *phy,
 
 	/* program CMN_CTRL_4 for minor_ver 2 chipsets*/
 	if ((phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V5_2) ||
+	    (phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V7_0) ||
 	    (readl(base + REG_DSI_7nm_PHY_CMN_REVISION_ID0) & (0xf0)) == 0x20)
 		writel(0x04, base + REG_DSI_7nm_PHY_CMN_CTRL_4);
 
@@ -1181,7 +1224,8 @@ static void dsi_7nm_phy_disable(struct msm_dsi_phy *phy)
 
 	/* Turn off REFGEN Vote */
 	if ((phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V4_3) ||
-	    (phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V5_2)) {
+	    (phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V5_2) ||
+	    (phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V7_0)) {
 		writel(0x0, base + REG_DSI_7nm_PHY_CMN_GLBL_DIGTOP_SPARE10);
 		wmb();
 		/* Delay to ensure HW removes vote before PHY shut down */
@@ -1402,3 +1446,26 @@ const struct msm_dsi_phy_cfg dsi_phy_4nm_8650_cfgs = {
 	.num_dsi_phy = 2,
 	.quirks = DSI_PHY_7NM_QUIRK_V5_2,
 };
+
+const struct msm_dsi_phy_cfg dsi_phy_3nm_8750_cfgs = {
+	.has_phy_lane = true,
+	.regulator_data = dsi_phy_7nm_98000uA_regulators,
+	.num_regulators = ARRAY_SIZE(dsi_phy_7nm_98000uA_regulators),
+	.ops = {
+		.enable = dsi_7nm_phy_enable,
+		.disable = dsi_7nm_phy_disable,
+		.pll_init = dsi_pll_7nm_init,
+		.save_pll_state = dsi_7nm_pll_save_state,
+		.restore_pll_state = dsi_7nm_pll_restore_state,
+		.set_continuous_clock = dsi_7nm_set_continuous_clock,
+	},
+	.min_pll_rate = 600000000UL,
+#ifdef CONFIG_64BIT
+	.max_pll_rate = 5000000000UL,
+#else
+	.max_pll_rate = ULONG_MAX,
+#endif
+	.io_start = { 0xae95000, 0xae97000 },
+	.num_dsi_phy = 2,
+	.quirks = DSI_PHY_7NM_QUIRK_V7_0,
+};
diff --git a/drivers/gpu/drm/msm/registers/display/dsi_phy_7nm.xml b/drivers/gpu/drm/msm/registers/display/dsi_phy_7nm.xml
index d49122b88d14896ef3e87b783a1691f85b61aa9c..f41516dd0567ca7406b0d41c9410e28084f2b03c 100644
--- a/drivers/gpu/drm/msm/registers/display/dsi_phy_7nm.xml
+++ b/drivers/gpu/drm/msm/registers/display/dsi_phy_7nm.xml
@@ -35,6 +35,7 @@ xsi:schemaLocation="https://gitlab.freedesktop.org/freedreno/ rules-fd.xsd">
 	<reg32 offset="0x00028" name="CTRL_1"/>
 	<reg32 offset="0x0002c" name="CTRL_2"/>
 	<reg32 offset="0x00030" name="CTRL_3"/>
+	<reg32 offset="0x001b0" name="CTRL_5"/>
 	<reg32 offset="0x00034" name="LANE_CFG0"/>
 	<reg32 offset="0x00038" name="LANE_CFG1"/>
 	<reg32 offset="0x0003c" name="PLL_CNTRL"/>
@@ -200,11 +201,24 @@ xsi:schemaLocation="https://gitlab.freedesktop.org/freedreno/ rules-fd.xsd">
 	<reg32 offset="0x01b0" name="COMMON_STATUS_ONE"/>
 	<reg32 offset="0x01b4" name="COMMON_STATUS_TWO"/>
 	<reg32 offset="0x01b8" name="BAND_SEL_CAL"/>
+	<!--
+	Starting with SM8750, offset moved from 0x01bc to 0x01cc, however
+	we keep only one register map.  That's not a problem, so far,
+	because this register is not used.  The register map should be split
+	once it is going to be used.  Comment out the code to prevent
+	any misuse due to the change in the offset.
 	<reg32 offset="0x01bc" name="ICODE_ACCUM_STATUS_LOW"/>
+	<reg32 offset="0x01cc" name="ICODE_ACCUM_STATUS_LOW"/>
+	-->
 	<reg32 offset="0x01c0" name="ICODE_ACCUM_STATUS_HIGH"/>
 	<reg32 offset="0x01c4" name="FD_OUT_LOW"/>
 	<reg32 offset="0x01c8" name="FD_OUT_HIGH"/>
+	<!--
+	Starting with SM8750, offset moved from 0x01cc to 0x01bc, however
+	we keep only one register map.  See above comment.
 	<reg32 offset="0x01cc" name="ALOG_OBSV_BUS_STATUS_1"/>
+	<reg32 offset="0x01bc" name="ALOG_OBSV_BUS_STATUS_1"/>
+	-->
 	<reg32 offset="0x01d0" name="PLL_MISC_CONFIG"/>
 	<reg32 offset="0x01d4" name="FLL_CONFIG"/>
 	<reg32 offset="0x01d8" name="FLL_FREQ_ACQ_TIME"/>

-- 
2.45.2