From: Pengyu Luo <mitltlatltl@gmail.com>
To: Bjorn Andersson <andersson@kernel.org>,
Konrad Dybcio <konradybcio@kernel.org>,
Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>
Cc: Pengyu Luo <mitltlatltl@gmail.com>,
linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org
Subject: [PATCH] arm64: dts: qcom: sc8280xp: Add GPI DMA configuration
Date: Thu, 5 Jun 2025 13:42:07 +0800 [thread overview]
Message-ID: <20250605054208.402581-1-mitltlatltl@gmail.com> (raw)
SPI on SC8280XP requires DMA (GSI) mode to function properly. Without it,
SPI controllers fall back to FIFO mode, which causes:
[ 0.901296] geni_spi 898000.spi: error -ENODEV: Failed to get tx DMA ch
[ 0.901305] geni_spi 898000.spi: FIFO mode disabled, but couldn't get DMA, fall back to FIFO mode
...
[ 45.605974] goodix-spi-hid spi0.0: SPI transfer timed out
[ 45.605988] geni_spi 898000.spi: Can't set CS when prev xfer running
[ 46.621555] spi_master spi0: failed to transfer one message from queue
[ 46.621568] spi_master spi0: noqueue transfer failed
[ 46.621577] goodix-spi-hid spi0.0: spi transfer error: -110
[ 46.621585] goodix-spi-hid spi0.0: probe with driver goodix-spi-hid failed with error -110
Therefore, add GPI DMA controller nodes for qup{0,1,2}, and add DMA
channels for SPI and I2C, UART is excluded for now, as it does not
yet support this mode.
Note that, since there is no public schematic, this configuration
is derived from Windows drivers. The drivers do not expose any DMA
channel mask information, so all available channels are enabled.
Signed-off-by: Pengyu Luo <mitltlatltl@gmail.com>
---
arch/arm64/boot/dts/qcom/sc8280xp.dtsi | 368 +++++++++++++++++++++++++
1 file changed, 368 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sc8280xp.dtsi b/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
index 87555a119..ff93ef837 100644
--- a/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
@@ -10,6 +10,7 @@
#include <dt-bindings/clock/qcom,rpmh.h>
#include <dt-bindings/clock/qcom,sc8280xp-camcc.h>
#include <dt-bindings/clock/qcom,sc8280xp-lpasscc.h>
+#include <dt-bindings/dma/qcom-gpi.h>
#include <dt-bindings/interconnect/qcom,osm-l3.h>
#include <dt-bindings/interconnect/qcom,sc8280xp.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
@@ -912,6 +913,32 @@ gpu_speed_bin: gpu-speed-bin@18b {
};
};
+ gpi_dma2: dma-controller@800000 {
+ compatible = "qcom,sc8280xp-gpi-dma", "qcom,sm6350-gpi-dma";
+ reg = <0 0x00800000 0 0x60000>;
+
+ interrupts = <GIC_SPI 588 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 589 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 590 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 591 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 592 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 593 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 594 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 595 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 596 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 597 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 598 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 599 IRQ_TYPE_LEVEL_HIGH>;
+
+ dma-channels = <12>;
+ dma-channel-mask = <0xfff>;
+ #dma-cells = <3>;
+
+ iommus = <&apps_smmu 0xb6 0x0>;
+
+ status = "disabled";
+ };
+
qup2: geniqup@8c0000 {
compatible = "qcom,geni-se-qup";
reg = <0 0x008c0000 0 0x2000>;
@@ -939,6 +966,12 @@ i2c16: i2c@880000 {
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
<&aggre1_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
+
+ dmas = <&gpi_dma2 0 6 QCOM_GPI_SPI>,
+ <&gpi_dma2 1 6 QCOM_GPI_SPI>;
+ dma-names = "tx",
+ "rx";
+
status = "disabled";
};
@@ -955,6 +988,12 @@ spi16: spi@880000 {
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
<&aggre1_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
+
+ dmas = <&gpi_dma2 0 0 QCOM_GPI_I2C>,
+ <&gpi_dma2 1 0 QCOM_GPI_I2C>;
+ dma-names = "tx",
+ "rx";
+
status = "disabled";
};
@@ -971,6 +1010,12 @@ i2c17: i2c@884000 {
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
<&aggre1_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
+
+ dmas = <&gpi_dma2 0 0 QCOM_GPI_SPI>,
+ <&gpi_dma2 1 0 QCOM_GPI_SPI>;
+ dma-names = "tx",
+ "rx";
+
status = "disabled";
};
@@ -987,6 +1032,12 @@ spi17: spi@884000 {
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
<&aggre1_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
+
+ dmas = <&gpi_dma2 0 1 QCOM_GPI_I2C>,
+ <&gpi_dma2 1 1 QCOM_GPI_I2C>;
+ dma-names = "tx",
+ "rx";
+
status = "disabled";
};
@@ -1017,6 +1068,12 @@ i2c18: i2c@888000 {
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
<&aggre1_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
+
+ dmas = <&gpi_dma2 0 1 QCOM_GPI_SPI>,
+ <&gpi_dma2 1 1 QCOM_GPI_SPI>;
+ dma-names = "tx",
+ "rx";
+
status = "disabled";
};
@@ -1033,6 +1090,12 @@ spi18: spi@888000 {
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
<&aggre1_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
+
+ dmas = <&gpi_dma2 0 2 QCOM_GPI_I2C>,
+ <&gpi_dma2 1 2 QCOM_GPI_I2C>;
+ dma-names = "tx",
+ "rx";
+
status = "disabled";
};
@@ -1067,6 +1130,12 @@ i2c19: i2c@88c000 {
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
<&aggre1_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
+
+ dmas = <&gpi_dma2 0 2 QCOM_GPI_SPI>,
+ <&gpi_dma2 1 2 QCOM_GPI_SPI>;
+ dma-names = "tx",
+ "rx";
+
status = "disabled";
};
@@ -1083,6 +1152,12 @@ spi19: spi@88c000 {
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
<&aggre1_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
+
+ dmas = <&gpi_dma2 0 3 QCOM_GPI_I2C>,
+ <&gpi_dma2 1 3 QCOM_GPI_I2C>;
+ dma-names = "tx",
+ "rx";
+
status = "disabled";
};
@@ -1099,6 +1174,12 @@ i2c20: i2c@890000 {
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
<&aggre1_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
+
+ dmas = <&gpi_dma2 0 3 QCOM_GPI_SPI>,
+ <&gpi_dma2 1 3 QCOM_GPI_SPI>;
+ dma-names = "tx",
+ "rx";
+
status = "disabled";
};
@@ -1115,6 +1196,12 @@ spi20: spi@890000 {
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
<&aggre1_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
+
+ dmas = <&gpi_dma2 0 4 QCOM_GPI_I2C>,
+ <&gpi_dma2 1 4 QCOM_GPI_I2C>;
+ dma-names = "tx",
+ "rx";
+
status = "disabled";
};
@@ -1131,6 +1218,12 @@ i2c21: i2c@894000 {
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
<&aggre1_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
+
+ dmas = <&gpi_dma2 0 5 QCOM_GPI_I2C>,
+ <&gpi_dma2 1 5 QCOM_GPI_I2C>;
+ dma-names = "tx",
+ "rx";
+
status = "disabled";
};
@@ -1147,6 +1240,12 @@ spi21: spi@894000 {
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
<&aggre1_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
+
+ dmas = <&gpi_dma2 0 4 QCOM_GPI_SPI>,
+ <&gpi_dma2 1 4 QCOM_GPI_SPI>;
+ dma-names = "tx",
+ "rx";
+
status = "disabled";
};
@@ -1163,6 +1262,12 @@ i2c22: i2c@898000 {
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
<&aggre1_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
+
+ dmas = <&gpi_dma2 0 6 QCOM_GPI_I2C>,
+ <&gpi_dma2 1 6 QCOM_GPI_I2C>;
+ dma-names = "tx",
+ "rx";
+
status = "disabled";
};
@@ -1179,6 +1284,12 @@ spi22: spi@898000 {
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
<&aggre1_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
+
+ dmas = <&gpi_dma2 0 5 QCOM_GPI_SPI>,
+ <&gpi_dma2 1 5 QCOM_GPI_SPI>;
+ dma-names = "tx",
+ "rx";
+
status = "disabled";
};
@@ -1195,6 +1306,12 @@ i2c23: i2c@89c000 {
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
<&aggre1_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
+
+ dmas = <&gpi_dma2 0 7 QCOM_GPI_I2C>,
+ <&gpi_dma2 1 7 QCOM_GPI_I2C>;
+ dma-names = "tx",
+ "rx";
+
status = "disabled";
};
@@ -1211,10 +1328,43 @@ spi23: spi@89c000 {
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
<&aggre1_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
+
+ dmas = <&gpi_dma2 0 7 QCOM_GPI_SPI>,
+ <&gpi_dma2 1 7 QCOM_GPI_SPI>;
+ dma-names = "tx",
+ "rx";
+
status = "disabled";
};
};
+ gpi_dma0: dma-controller@900000 {
+ compatible = "qcom,sc8280xp-gpi-dma", "qcom,sm6350-gpi-dma";
+ reg = <0 0x00900000 0 0x60000>;
+
+ interrupts = <GIC_SPI 244 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 245 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 247 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 250 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 251 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 252 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 253 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>;
+
+ dma-channels = <13>;
+ dma-channel-mask = <0x1fff>;
+ #dma-cells = <3>;
+
+ iommus = <&apps_smmu 0x576 0x0>;
+
+ status = "disabled";
+ };
+
qup0: geniqup@9c0000 {
compatible = "qcom,geni-se-qup";
reg = <0 0x009c0000 0 0x6000>;
@@ -1242,6 +1392,12 @@ i2c0: i2c@980000 {
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>,
<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
+
+ dmas = <&gpi_dma0 0 7 QCOM_GPI_I2C>,
+ <&gpi_dma0 1 7 QCOM_GPI_I2C>;
+ dma-names = "tx",
+ "rx";
+
status = "disabled";
};
@@ -1258,6 +1414,12 @@ spi0: spi@980000 {
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>,
<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
+
+ dmas = <&gpi_dma0 0 0 QCOM_GPI_I2C>,
+ <&gpi_dma0 1 0 QCOM_GPI_I2C>;
+ dma-names = "tx",
+ "rx";
+
status = "disabled";
};
@@ -1274,6 +1436,12 @@ i2c1: i2c@984000 {
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>,
<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
+
+ dmas = <&gpi_dma0 0 0 QCOM_GPI_SPI>,
+ <&gpi_dma0 1 0 QCOM_GPI_SPI>;
+ dma-names = "tx",
+ "rx";
+
status = "disabled";
};
@@ -1290,6 +1458,12 @@ spi1: spi@984000 {
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>,
<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
+
+ dmas = <&gpi_dma0 0 1 QCOM_GPI_I2C>,
+ <&gpi_dma0 1 1 QCOM_GPI_I2C>;
+ dma-names = "tx",
+ "rx";
+
status = "disabled";
};
@@ -1306,6 +1480,12 @@ i2c2: i2c@988000 {
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>,
<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
+
+ dmas = <&gpi_dma0 0 1 QCOM_GPI_SPI>,
+ <&gpi_dma0 1 1 QCOM_GPI_SPI>;
+ dma-names = "tx",
+ "rx";
+
status = "disabled";
};
@@ -1322,6 +1502,12 @@ spi2: spi@988000 {
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>,
<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
+
+ dmas = <&gpi_dma0 0 2 QCOM_GPI_I2C>,
+ <&gpi_dma0 1 2 QCOM_GPI_I2C>;
+ dma-names = "tx",
+ "rx";
+
status = "disabled";
};
@@ -1352,6 +1538,12 @@ i2c3: i2c@98c000 {
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>,
<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
+
+ dmas = <&gpi_dma0 0 2 QCOM_GPI_SPI>,
+ <&gpi_dma0 1 2 QCOM_GPI_SPI>;
+ dma-names = "tx",
+ "rx";
+
status = "disabled";
};
@@ -1368,6 +1560,12 @@ spi3: spi@98c000 {
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>,
<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
+
+ dmas = <&gpi_dma0 0 3 QCOM_GPI_I2C>,
+ <&gpi_dma0 1 3 QCOM_GPI_I2C>;
+ dma-names = "tx",
+ "rx";
+
status = "disabled";
};
@@ -1384,6 +1582,12 @@ i2c4: i2c@990000 {
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>,
<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
+
+ dmas = <&gpi_dma0 0 3 QCOM_GPI_SPI>,
+ <&gpi_dma0 1 3 QCOM_GPI_SPI>;
+ dma-names = "tx",
+ "rx";
+
status = "disabled";
};
@@ -1400,6 +1604,12 @@ spi4: spi@990000 {
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>,
<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
+
+ dmas = <&gpi_dma0 0 4 QCOM_GPI_I2C>,
+ <&gpi_dma0 1 4 QCOM_GPI_I2C>;
+ dma-names = "tx",
+ "rx";
+
status = "disabled";
};
@@ -1416,6 +1626,12 @@ i2c5: i2c@994000 {
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>,
<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
+
+ dmas = <&gpi_dma0 0 4 QCOM_GPI_SPI>,
+ <&gpi_dma0 1 4 QCOM_GPI_SPI>;
+ dma-names = "tx",
+ "rx";
+
status = "disabled";
};
@@ -1432,6 +1648,12 @@ spi5: spi@994000 {
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>,
<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
+
+ dmas = <&gpi_dma0 0 5 QCOM_GPI_I2C>,
+ <&gpi_dma0 1 5 QCOM_GPI_I2C>;
+ dma-names = "tx",
+ "rx";
+
status = "disabled";
};
@@ -1448,6 +1670,12 @@ i2c6: i2c@998000 {
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>,
<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
+
+ dmas = <&gpi_dma0 0 5 QCOM_GPI_SPI>,
+ <&gpi_dma0 1 5 QCOM_GPI_SPI>;
+ dma-names = "tx",
+ "rx";
+
status = "disabled";
};
@@ -1464,6 +1692,12 @@ spi6: spi@998000 {
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>,
<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
+
+ dmas = <&gpi_dma0 0 6 QCOM_GPI_I2C>,
+ <&gpi_dma0 1 6 QCOM_GPI_I2C>;
+ dma-names = "tx",
+ "rx";
+
status = "disabled";
};
@@ -1480,6 +1714,12 @@ i2c7: i2c@99c000 {
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>,
<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
+
+ dmas = <&gpi_dma0 0 6 QCOM_GPI_SPI>,
+ <&gpi_dma0 1 6 QCOM_GPI_SPI>;
+ dma-names = "tx",
+ "rx";
+
status = "disabled";
};
@@ -1496,10 +1736,42 @@ spi7: spi@99c000 {
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>,
<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
+
+ dmas = <&gpi_dma0 0 7 QCOM_GPI_SPI>,
+ <&gpi_dma0 1 7 QCOM_GPI_SPI>;
+ dma-names = "tx",
+ "rx";
+
status = "disabled";
};
};
+ gpi_dma1: dma-controller@a00000 {
+ compatible = "qcom,sc8280xp-gpi-dma", "qcom,sm6350-gpi-dma";
+ reg = <0 0x00a00000 0 0x60000>;
+
+ interrupts = <GIC_SPI 279 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 280 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 281 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 282 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 283 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 284 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 293 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 294 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 295 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 296 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 297 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 298 IRQ_TYPE_LEVEL_HIGH>;
+
+ dma-channels = <12>;
+ dma-channel-mask = <0xfff>;
+ #dma-cells = <3>;
+
+ iommus = <&apps_smmu 0x96 0x0>;
+
+ status = "disabled";
+ };
+
qup1: geniqup@ac0000 {
compatible = "qcom,geni-se-qup";
reg = <0 0x00ac0000 0 0x6000>;
@@ -1527,6 +1799,12 @@ i2c8: i2c@a80000 {
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
<&aggre1_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
+
+ dmas = <&gpi_dma1 0 7 QCOM_GPI_I2C>,
+ <&gpi_dma1 1 7 QCOM_GPI_I2C>;
+ dma-names = "tx",
+ "rx";
+
status = "disabled";
};
@@ -1543,6 +1821,12 @@ spi8: spi@a80000 {
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
<&aggre1_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
+
+ dmas = <&gpi_dma1 0 0 QCOM_GPI_I2C>,
+ <&gpi_dma1 1 0 QCOM_GPI_I2C>;
+ dma-names = "tx",
+ "rx";
+
status = "disabled";
};
@@ -1559,6 +1843,12 @@ i2c9: i2c@a84000 {
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
<&aggre1_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
+
+ dmas = <&gpi_dma1 0 0 QCOM_GPI_SPI>,
+ <&gpi_dma1 1 0 QCOM_GPI_SPI>;
+ dma-names = "tx",
+ "rx";
+
status = "disabled";
};
@@ -1575,6 +1865,12 @@ spi9: spi@a84000 {
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
<&aggre1_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
+
+ dmas = <&gpi_dma1 0 1 QCOM_GPI_I2C>,
+ <&gpi_dma1 1 1 QCOM_GPI_I2C>;
+ dma-names = "tx",
+ "rx";
+
status = "disabled";
};
@@ -1591,6 +1887,12 @@ i2c10: i2c@a88000 {
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
<&aggre1_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
+
+ dmas = <&gpi_dma1 0 1 QCOM_GPI_SPI>,
+ <&gpi_dma1 1 1 QCOM_GPI_SPI>;
+ dma-names = "tx",
+ "rx";
+
status = "disabled";
};
@@ -1607,6 +1909,12 @@ spi10: spi@a88000 {
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
<&aggre1_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
+
+ dmas = <&gpi_dma1 0 2 QCOM_GPI_I2C>,
+ <&gpi_dma1 1 2 QCOM_GPI_I2C>;
+ dma-names = "tx",
+ "rx";
+
status = "disabled";
};
@@ -1623,6 +1931,12 @@ i2c11: i2c@a8c000 {
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
<&aggre1_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
+
+ dmas = <&gpi_dma1 0 2 QCOM_GPI_SPI>,
+ <&gpi_dma1 1 2 QCOM_GPI_SPI>;
+ dma-names = "tx",
+ "rx";
+
status = "disabled";
};
@@ -1639,6 +1953,12 @@ spi11: spi@a8c000 {
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
<&aggre1_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
+
+ dmas = <&gpi_dma1 0 3 QCOM_GPI_I2C>,
+ <&gpi_dma1 1 3 QCOM_GPI_I2C>;
+ dma-names = "tx",
+ "rx";
+
status = "disabled";
};
@@ -1655,6 +1975,12 @@ i2c12: i2c@a90000 {
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
<&aggre1_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
+
+ dmas = <&gpi_dma1 0 3 QCOM_GPI_SPI>,
+ <&gpi_dma1 1 3 QCOM_GPI_SPI>;
+ dma-names = "tx",
+ "rx";
+
status = "disabled";
};
@@ -1671,6 +1997,12 @@ spi12: spi@a90000 {
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
<&aggre1_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
+
+ dmas = <&gpi_dma1 0 4 QCOM_GPI_I2C>,
+ <&gpi_dma1 1 4 QCOM_GPI_I2C>;
+ dma-names = "tx",
+ "rx";
+
status = "disabled";
};
@@ -1687,6 +2019,12 @@ i2c13: i2c@a94000 {
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
<&aggre1_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
+
+ dmas = <&gpi_dma1 0 4 QCOM_GPI_SPI>,
+ <&gpi_dma1 1 4 QCOM_GPI_SPI>;
+ dma-names = "tx",
+ "rx";
+
status = "disabled";
};
@@ -1703,6 +2041,12 @@ spi13: spi@a94000 {
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
<&aggre1_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
+
+ dmas = <&gpi_dma1 0 5 QCOM_GPI_I2C>,
+ <&gpi_dma1 1 5 QCOM_GPI_I2C>;
+ dma-names = "tx",
+ "rx";
+
status = "disabled";
};
@@ -1719,6 +2063,12 @@ i2c14: i2c@a98000 {
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
<&aggre1_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
+
+ dmas = <&gpi_dma1 0 5 QCOM_GPI_SPI>,
+ <&gpi_dma1 1 5 QCOM_GPI_SPI>;
+ dma-names = "tx",
+ "rx";
+
status = "disabled";
};
@@ -1735,6 +2085,12 @@ spi14: spi@a98000 {
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
<&aggre1_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
+
+ dmas = <&gpi_dma1 0 6 QCOM_GPI_I2C>,
+ <&gpi_dma1 1 6 QCOM_GPI_I2C>;
+ dma-names = "tx",
+ "rx";
+
status = "disabled";
};
@@ -1751,6 +2107,12 @@ i2c15: i2c@a9c000 {
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
<&aggre1_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
+
+ dmas = <&gpi_dma1 0 6 QCOM_GPI_SPI>,
+ <&gpi_dma1 1 6 QCOM_GPI_SPI>;
+ dma-names = "tx",
+ "rx";
+
status = "disabled";
};
@@ -1767,6 +2129,12 @@ spi15: spi@a9c000 {
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
<&aggre1_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
+
+ dmas = <&gpi_dma1 0 7 QCOM_GPI_SPI>,
+ <&gpi_dma1 1 7 QCOM_GPI_SPI>;
+ dma-names = "tx",
+ "rx";
+
status = "disabled";
};
};
--
2.49.0
next reply other threads:[~2025-06-05 5:42 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-06-05 5:42 Pengyu Luo [this message]
2025-06-05 6:37 ` [PATCH] arm64: dts: qcom: sc8280xp: Add GPI DMA configuration Dmitry Baryshkov
2025-06-05 12:49 ` Rob Herring (Arm)
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20250605054208.402581-1-mitltlatltl@gmail.com \
--to=mitltlatltl@gmail.com \
--cc=andersson@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=konradybcio@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox