[PATCH v4 4/4] arm64: dts: qcom: sdm632-fairphone-fp3: Enable display and GPU

[Luca Weiss <luca@lucaweiss.eu>]

Add the description for the display panel found on this phone.
Unfortunately the LCDB module on PMI632 isn't yet supported upstream so
we need to use a dummy regulator-fixed in the meantime.

And with this done we can also enable the GPU and set the zap shader
firmware path.

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Luca Weiss <luca@lucaweiss.eu>
---
 arch/arm64/boot/dts/qcom/msm8953.dtsi             |  2 +-
 arch/arm64/boot/dts/qcom/sdm632-fairphone-fp3.dts | 62 +++++++++++++++++++++++
 2 files changed, 63 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/qcom/msm8953.dtsi b/arch/arm64/boot/dts/qcom/msm8953.dtsi
index 273e79fb75695af1fd7a6f77273b95fe3b913fac..c5205d09c442e45e4a0cc3e6d8ff7d9d7bda0034 100644
--- a/arch/arm64/boot/dts/qcom/msm8953.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8953.dtsi
@@ -1147,7 +1147,7 @@ &bimc SLV_EBI RPM_ALWAYS_TAG>,
 
 			status = "disabled";
 
-			zap-shader {
+			gpu_zap_shader: zap-shader {
 				memory-region = <&zap_shader_region>;
 			};
 
diff --git a/arch/arm64/boot/dts/qcom/sdm632-fairphone-fp3.dts b/arch/arm64/boot/dts/qcom/sdm632-fairphone-fp3.dts
index 31ed26c31e6ea381a8942ccf569513df3300cdeb..55a45b528bd3f1bf9b6fe7882753338b43c62271 100644
--- a/arch/arm64/boot/dts/qcom/sdm632-fairphone-fp3.dts
+++ b/arch/arm64/boot/dts/qcom/sdm632-fairphone-fp3.dts
@@ -36,6 +36,14 @@ key-volume-up {
 		};
 	};
 
+	/* Dummy regulator until PMI632 has LCDB VSP/VSN support */
+	lcdb_dummy: regulator-lcdb-dummy {
+		compatible = "regulator-fixed";
+		regulator-name = "lcdb_dummy";
+		regulator-min-microvolt = <5500000>;
+		regulator-max-microvolt = <5500000>;
+	};
+
 	vph_pwr: vph-pwr-regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "vph_pwr";
@@ -44,6 +52,14 @@ vph_pwr: vph-pwr-regulator {
 	};
 };
 
+&gpu {
+	status = "okay";
+};
+
+&gpu_zap_shader {
+	firmware-name = "qcom/msm8953/fairphone/fp3/a506_zap.mbn";
+};
+
 &hsusb_phy {
 	vdd-supply = <&pm8953_l3>;
 	vdda-pll-supply = <&pm8953_l7>;
@@ -87,6 +103,45 @@ &lpass {
 	status = "okay";
 };
 
+&mdss {
+	status = "okay";
+};
+
+&mdss_dsi0 {
+	vdda-supply = <&pm8953_s3>;
+	status = "okay";
+
+	panel@0 {
+		compatible = "djn,98-03057-6598b-i";
+		reg = <0>;
+
+		reset-gpios = <&tlmm 61 GPIO_ACTIVE_LOW>;
+
+		iovcc-supply = <&pm8953_l6>;
+		vsn-supply = <&lcdb_dummy>;
+		vsp-supply = <&lcdb_dummy>;
+
+		pinctrl-0 = <&mdss_te_default>;
+		pinctrl-names = "default";
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&mdss_dsi0_out>;
+			};
+		};
+	};
+};
+
+&mdss_dsi0_out {
+	data-lanes = <0 1 2 3>;
+	remote-endpoint = <&panel_in>;
+};
+
+&mdss_dsi0_phy {
+	vcca-supply = <&pm8953_l3>;
+	status = "okay";
+};
+
 &mpss {
 	firmware-name = "qcom/msm8953/fairphone/fp3/mba.mbn",
 			"qcom/msm8953/fairphone/fp3/modem.mbn";
@@ -292,6 +347,13 @@ &tlmm {
 	 * 135-138: fingerprint reader (SPI)
 	 */
 	gpio-reserved-ranges = <0 4>, <135 4>;
+
+	mdss_te_default: mdss-te-default-state {
+		pins = "gpio24";
+		function = "mdp_vsync";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
 };
 
 &uart_0 {

-- 
2.49.0