[PATCH v7 0/8] spacemit: introduce P1 PMIC support

[PATCH v7 0/8] spacemit: introduce P1 PMIC support

[Alex Elder]

The SpacemiT P1 is an I2C-controlled PMIC that implements 6 buck
converters and 12 LDOs.  It contains a load switch, ADC channels,
GPIOs, a real-time clock, and a watchdog timer.

This series introduces a multifunction driver for the P1 PMIC as well
as drivers for its regulators and RTC.

In v6, a new patch was added to change the simple MFD driver to
allow the regmap max_register value in the simple MFD configuration.
However it also removed the option of specifying a "full" regmap
configuration, and that was not what Lee Jones actually wanted.

This version adds the max_register option, but also retains the
ability to supply a full regmap config.  (If both are specified,
the max_register value is ignored.)

					-Alex

This series is available here:
  https://github.com/riscstar/linux/tree/outgoing/pmic-v7

Between version 5 and version 6:
  - Revise patch 2 to preserve the option to provide a full regmap config

Here is version 6 of this series:
  https://lore.kernel.org/lkml/20250627142309.1444135-1-elder@riscstar.com/

Between version 5 and version 6:
  - Added Rob Herring's reviewed-by to patch 1
  - Add the simple MFD functionality suggested by Lee Jones
  - Update patch 3 (previously 2) accordingly

Here is version 5 of this series:
  https://lore.kernel.org/lkml/20250625164119.1068842-1-elder@riscstar.com/

Between version 4 and version 5:
  - Only check the seconds register for change when looping on read
  - Return without re-enabling the RTC if writing registers fails
  - If the RTC is disabled when reading, return an error

Here is version 4 of this series:
  https://lore.kernel.org/lkml/20250625164119.1068842-1-elder@riscstar.com/

More complete history is available at that link.

Alex Elder (8):
  dt-bindings: mfd: add support the SpacemiT P1 PMIC
  mfd: simple-mfd-i2c: specify max_register
  mfd: simple-mfd-i2c: add SpacemiT P1 support
  regulator: spacemit: support SpacemiT P1 regulators
  rtc: spacemit: support the SpacemiT P1 RTC
  riscv: dts: spacemit: enable the i2c8 adapter
  riscv: dts: spacemit: define fixed regulators
  riscv: dts: spacemit: define regulator constraints

 .../devicetree/bindings/mfd/spacemit,p1.yaml  |  86 +++++++++
 .../boot/dts/spacemit/k1-bananapi-f3.dts      | 138 +++++++++++++++
 arch/riscv/boot/dts/spacemit/k1-pinctrl.dtsi  |   7 +
 arch/riscv/boot/dts/spacemit/k1.dtsi          |  11 ++
 drivers/mfd/Kconfig                           |  11 ++
 drivers/mfd/simple-mfd-i2c.c                  |  27 ++-
 drivers/mfd/simple-mfd-i2c.h                  |   1 +
 drivers/regulator/Kconfig                     |  12 ++
 drivers/regulator/Makefile                    |   1 +
 drivers/regulator/spacemit-p1.c               | 157 ++++++++++++++++
 drivers/rtc/Kconfig                           |  10 ++
 drivers/rtc/Makefile                          |   1 +
 drivers/rtc/rtc-spacemit-p1.c                 | 167 ++++++++++++++++++
 13 files changed, 626 insertions(+), 3 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/mfd/spacemit,p1.yaml
 create mode 100644 drivers/regulator/spacemit-p1.c
 create mode 100644 drivers/rtc/rtc-spacemit-p1.c


base-commit: 50c8770a42faf8b1c7abe93e7c114337f580a97d
-- 
2.45.2

[PATCH v7 1/8] dt-bindings: mfd: add support the SpacemiT P1 PMIC

[Alex Elder]

Enable the SpacemiT P1, which is an I2C-controlled PMIC.  Initially
only the RTC and regulators will be supported.

Signed-off-by: Alex Elder <elder@riscstar.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
---
 .../devicetree/bindings/mfd/spacemit,p1.yaml  | 86 +++++++++++++++++++
 1 file changed, 86 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mfd/spacemit,p1.yaml

diff --git a/Documentation/devicetree/bindings/mfd/spacemit,p1.yaml b/Documentation/devicetree/bindings/mfd/spacemit,p1.yaml
new file mode 100644
index 0000000000000..5cc34d4934b54
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/spacemit,p1.yaml
@@ -0,0 +1,86 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/spacemit,p1.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: SpacemiT P1 Power Management Integrated Circuit
+
+maintainers:
+  - Troy Mitchell <troymitchell988@gmail.com>
+
+description:
+  P1 is an I2C-controlled PMIC produced by SpacemiT.  It implements six
+  constant-on-time buck converters and twelve low-dropout regulators.
+  It also contains a load switch, watchdog timer, real-time clock, eight
+  12-bit ADC channels, and six GPIOs.  Additional details are available
+  in the "Power Stone/P1" section at the following link.
+    https://developer.spacemit.com/documentation
+
+properties:
+  compatible:
+    const: spacemit,p1
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  vin-supply:
+    description: Input supply phandle.
+
+  regulators:
+    type: object
+
+    patternProperties:
+      "^(buck[1-6]|aldo[1-4]|dldo[1-7])$":
+        type: object
+        $ref: /schemas/regulator/regulator.yaml#
+        unevaluatedProperties: false
+
+    unevaluatedProperties: false
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        pmic@41 {
+            compatible = "spacemit,p1";
+            reg = <0x41>;
+            interrupts = <64>;
+
+            regulators {
+                buck1 {
+                    regulator-name = "buck1";
+                    regulator-min-microvolt = <500000>;
+                    regulator-max-microvolt = <3450000>;
+                    regulator-ramp-delay = <5000>;
+                    regulator-always-on;
+                };
+
+                aldo1 {
+                    regulator-name = "aldo1";
+                    regulator-min-microvolt = <500000>;
+                    regulator-max-microvolt = <3400000>;
+                    regulator-boot-on;
+                };
+
+                dldo1 {
+                    regulator-name = "dldo1";
+                    regulator-min-microvolt = <500000>;
+                    regulator-max-microvolt = <3400000>;
+                    regulator-boot-on;
+                };
+            };
+        };
+    };
-- 
2.45.2

[PATCH v7 2/8] mfd: simple-mfd-i2c: specify max_register

[Alex Elder]

All devices supported by simple MFD use the same 8-bit register
8-bit value regmap configuration.  There is an option available
for a device to specify a custom configuration, but no existing
device uses it.

Rather than specify a "full" regmap configuration to use this
option, Lee Jones suggested allowing just the max_register value
to be specified in the simple_mfd_data structure.

Signed-off-by: Alex Elder <elder@riscstar.com>
Suggested-by: Lee Jones <lee@kernel.org>
---
v2: - Allow max_register *and* regmap_config to be supplied

 drivers/mfd/simple-mfd-i2c.c | 15 ++++++++++++---
 drivers/mfd/simple-mfd-i2c.h |  1 +
 2 files changed, 13 insertions(+), 3 deletions(-)

diff --git a/drivers/mfd/simple-mfd-i2c.c b/drivers/mfd/simple-mfd-i2c.c
index 22159913bea03..3f959f4f98261 100644
--- a/drivers/mfd/simple-mfd-i2c.c
+++ b/drivers/mfd/simple-mfd-i2c.c
@@ -33,16 +33,25 @@ static int simple_mfd_i2c_probe(struct i2c_client *i2c)
 {
 	const struct simple_mfd_data *simple_mfd_data;
 	const struct regmap_config *regmap_config;
+	struct regmap_config config;
 	struct regmap *regmap;
 	int ret;
 
 	simple_mfd_data = device_get_match_data(&i2c->dev);
 
 	/* If no regmap_config is specified, use the default 8reg and 8val bits */
-	if (!simple_mfd_data || !simple_mfd_data->regmap_config)
+	if (simple_mfd_data) {
+		if (simple_mfd_data->regmap_config)
+			config = *simple_mfd_data->regmap_config;
+		else
+			config = regmap_config_8r_8v;
+
+		if (simple_mfd_data->max_register)
+			config.max_register = simple_mfd_data->max_register;
+		regmap_config = &config;
+	} else {
 		regmap_config = &regmap_config_8r_8v;
-	else
-		regmap_config = simple_mfd_data->regmap_config;
+	}
 
 	regmap = devm_regmap_init_i2c(i2c, regmap_config);
 	if (IS_ERR(regmap))
diff --git a/drivers/mfd/simple-mfd-i2c.h b/drivers/mfd/simple-mfd-i2c.h
index 7cb2bdd347d97..706b6f53155ff 100644
--- a/drivers/mfd/simple-mfd-i2c.h
+++ b/drivers/mfd/simple-mfd-i2c.h
@@ -27,6 +27,7 @@ struct simple_mfd_data {
 	const struct regmap_config *regmap_config;
 	const struct mfd_cell *mfd_cell;
 	size_t mfd_cell_size;
+	unsigned int max_register;
 };
 
 #endif /* __MFD_SIMPLE_MFD_I2C_H */
-- 
2.45.2

Re: [PATCH v7 2/8] mfd: simple-mfd-i2c: specify max_register

[Lee Jones]

On Wed, 02 Jul 2025, Alex Elder wrote:

> All devices supported by simple MFD use the same 8-bit register
> 8-bit value regmap configuration.  There is an option available
> for a device to specify a custom configuration, but no existing
> device uses it.
> 
> Rather than specify a "full" regmap configuration to use this
> option, Lee Jones suggested allowing just the max_register value
> to be specified in the simple_mfd_data structure.
> 
> Signed-off-by: Alex Elder <elder@riscstar.com>
> Suggested-by: Lee Jones <lee@kernel.org>
> ---
> v2: - Allow max_register *and* regmap_config to be supplied
> 
>  drivers/mfd/simple-mfd-i2c.c | 15 ++++++++++++---
>  drivers/mfd/simple-mfd-i2c.h |  1 +
>  2 files changed, 13 insertions(+), 3 deletions(-)
> 
> diff --git a/drivers/mfd/simple-mfd-i2c.c b/drivers/mfd/simple-mfd-i2c.c
> index 22159913bea03..3f959f4f98261 100644
> --- a/drivers/mfd/simple-mfd-i2c.c
> +++ b/drivers/mfd/simple-mfd-i2c.c
> @@ -33,16 +33,25 @@ static int simple_mfd_i2c_probe(struct i2c_client *i2c)
>  {
>  	const struct simple_mfd_data *simple_mfd_data;
>  	const struct regmap_config *regmap_config;

> +	struct regmap_config config;

Why do we need another regmap_config?

Can't we just remove the const and make use of the one above?

>  	struct regmap *regmap;
>  	int ret;
>  
>  	simple_mfd_data = device_get_match_data(&i2c->dev);
>  
>  	/* If no regmap_config is specified, use the default 8reg and 8val bits */
> -	if (!simple_mfd_data || !simple_mfd_data->regmap_config)
> +	if (simple_mfd_data) {
> +		if (simple_mfd_data->regmap_config)
> +			config = *simple_mfd_data->regmap_config;

			regmap_config = simple_mfd_data->regmap_config;

> +		else
> +			config = regmap_config_8r_8v;

			regmap_config = &regmap_config_8r_8v;
> +
> +		if (simple_mfd_data->max_register)
> +			config.max_register = simple_mfd_data->max_register;
> +		regmap_config = &config;
> +	} else {
>  		regmap_config = &regmap_config_8r_8v;

I suspect we don't need to have this line twice.

Either re-jig the if () above (I suspect this explains the existing
complexity [multiple conditions]) or pre-set regmap_config to
regmap_config_8r_8v and only over-write it if the conditions are met.

> -	else -		regmap_config = simple_mfd_data->regmap_config;
> +	}
>  
>  	regmap = devm_regmap_init_i2c(i2c, regmap_config); if
>  	(IS_ERR(regmap)) diff --git a/drivers/mfd/simple-mfd-i2c.h
>  	b/drivers/mfd/simple-mfd-i2c.h index
>  	7cb2bdd347d97..706b6f53155ff 100644 ---
>  	a/drivers/mfd/simple-mfd-i2c.h +++
>  	b/drivers/mfd/simple-mfd-i2c.h @@ -27,6 +27,7 @@ struct
>  	simple_mfd_data { const struct regmap_config *regmap_config;
>  	const struct mfd_cell *mfd_cell; size_t mfd_cell_size; +
>  	unsigned int max_register; };
>  
>  #endif /* __MFD_SIMPLE_MFD_I2C_H */ -- 2.45.2
> 

-- 
Lee Jones [李琼斯]

Re: [PATCH v7 2/8] mfd: simple-mfd-i2c: specify max_register

[Lee Jones]

On Thu, 10 Jul 2025, Lee Jones wrote:

> On Wed, 02 Jul 2025, Alex Elder wrote:
> 
> > All devices supported by simple MFD use the same 8-bit register
> > 8-bit value regmap configuration.  There is an option available
> > for a device to specify a custom configuration, but no existing
> > device uses it.
> > 
> > Rather than specify a "full" regmap configuration to use this
> > option, Lee Jones suggested allowing just the max_register value
> > to be specified in the simple_mfd_data structure.
> > 
> > Signed-off-by: Alex Elder <elder@riscstar.com>
> > Suggested-by: Lee Jones <lee@kernel.org>
> > ---
> > v2: - Allow max_register *and* regmap_config to be supplied
> > 
> >  drivers/mfd/simple-mfd-i2c.c | 15 ++++++++++++---
> >  drivers/mfd/simple-mfd-i2c.h |  1 +
> >  2 files changed, 13 insertions(+), 3 deletions(-)
> > 
> > diff --git a/drivers/mfd/simple-mfd-i2c.c b/drivers/mfd/simple-mfd-i2c.c
> > index 22159913bea03..3f959f4f98261 100644
> > --- a/drivers/mfd/simple-mfd-i2c.c
> > +++ b/drivers/mfd/simple-mfd-i2c.c
> > @@ -33,16 +33,25 @@ static int simple_mfd_i2c_probe(struct i2c_client *i2c)
> >  {
> >  	const struct simple_mfd_data *simple_mfd_data;
> >  	const struct regmap_config *regmap_config;
> 
> > +	struct regmap_config config;
> 
> Why do we need another regmap_config?
> 
> Can't we just remove the const and make use of the one above?
> 
> >  	struct regmap *regmap;
> >  	int ret;
> >  
> >  	simple_mfd_data = device_get_match_data(&i2c->dev);
> >  
> >  	/* If no regmap_config is specified, use the default 8reg and 8val bits */
> > -	if (!simple_mfd_data || !simple_mfd_data->regmap_config)
> > +	if (simple_mfd_data) {
> > +		if (simple_mfd_data->regmap_config)
> > +			config = *simple_mfd_data->regmap_config;
> 
> 			regmap_config = simple_mfd_data->regmap_config;
> 
> > +		else
> > +			config = regmap_config_8r_8v;
> 
> 			regmap_config = &regmap_config_8r_8v;
> > +
> > +		if (simple_mfd_data->max_register)
> > +			config.max_register = simple_mfd_data->max_register;
> > +		regmap_config = &config;
> > +	} else {
> >  		regmap_config = &regmap_config_8r_8v;
> 
> I suspect we don't need to have this line twice.
> 
> Either re-jig the if () above (I suspect this explains the existing
> complexity [multiple conditions]) or pre-set regmap_config to
> regmap_config_8r_8v and only over-write it if the conditions are met.

Not sure why this whole thing had to be reworked.

Why didn't the 2-liner I gave you work for you?

-- 
Lee Jones [李琼斯]

Re: [PATCH v7 2/8] mfd: simple-mfd-i2c: specify max_register

[Alex Elder]

On 7/10/25 4:24 AM, Lee Jones wrote:
> On Wed, 02 Jul 2025, Alex Elder wrote:
> 
>> All devices supported by simple MFD use the same 8-bit register
>> 8-bit value regmap configuration.  There is an option available
>> for a device to specify a custom configuration, but no existing
>> device uses it.
>>
>> Rather than specify a "full" regmap configuration to use this
>> option, Lee Jones suggested allowing just the max_register value
>> to be specified in the simple_mfd_data structure.
>>
>> Signed-off-by: Alex Elder <elder@riscstar.com>
>> Suggested-by: Lee Jones <lee@kernel.org>
>> ---
>> v2: - Allow max_register *and* regmap_config to be supplied
>>
>>   drivers/mfd/simple-mfd-i2c.c | 15 ++++++++++++---
>>   drivers/mfd/simple-mfd-i2c.h |  1 +
>>   2 files changed, 13 insertions(+), 3 deletions(-)
>>
>> diff --git a/drivers/mfd/simple-mfd-i2c.c b/drivers/mfd/simple-mfd-i2c.c
>> index 22159913bea03..3f959f4f98261 100644
>> --- a/drivers/mfd/simple-mfd-i2c.c
>> +++ b/drivers/mfd/simple-mfd-i2c.c
>> @@ -33,16 +33,25 @@ static int simple_mfd_i2c_probe(struct i2c_client *i2c)
>>   {
>>   	const struct simple_mfd_data *simple_mfd_data;
>>   	const struct regmap_config *regmap_config;
> 
>> +	struct regmap_config config;
> 
> Why do we need another regmap_config?
> 
> Can't we just remove the const and make use of the one above?

If we change the global one, it changes for all users.

In my next version I will modify the global one temporarily and
zero the max_register field again after the devm_regmap_init_i2c()
call.  That doesn't protect against concurrent probes but I don't
think that's a problem.

>>   	struct regmap *regmap;
>>   	int ret;
>>   
>>   	simple_mfd_data = device_get_match_data(&i2c->dev);
>>   
>>   	/* If no regmap_config is specified, use the default 8reg and 8val bits */
>> -	if (!simple_mfd_data || !simple_mfd_data->regmap_config)
>> +	if (simple_mfd_data) {
>> +		if (simple_mfd_data->regmap_config)
>> +			config = *simple_mfd_data->regmap_config;
> 
> 			regmap_config = simple_mfd_data->regmap_config;
> 
>> +		else
>> +			config = regmap_config_8r_8v;
> 
> 			regmap_config = &regmap_config_8r_8v;
>> +
>> +		if (simple_mfd_data->max_register)
>> +			config.max_register = simple_mfd_data->max_register;
>> +		regmap_config = &config;
>> +	} else {
>>   		regmap_config = &regmap_config_8r_8v;
> 
> I suspect we don't need to have this line twice.
> 
> Either re-jig the if () above (I suspect this explains the existing
> complexity [multiple conditions]) or pre-set regmap_config to
> regmap_config_8r_8v and only over-write it if the conditions are met.

Sure, that would work, but it won't be needed if I just use
the (non-const) global config.

Thanks for the review.

					-Alex
		
> 
>> -	else -		regmap_config = simple_mfd_data->regmap_config;
>> +	}
>>   
>>   	regmap = devm_regmap_init_i2c(i2c, regmap_config); if
>>   	(IS_ERR(regmap)) diff --git a/drivers/mfd/simple-mfd-i2c.h
>>   	b/drivers/mfd/simple-mfd-i2c.h index
>>   	7cb2bdd347d97..706b6f53155ff 100644 ---
>>   	a/drivers/mfd/simple-mfd-i2c.h +++
>>   	b/drivers/mfd/simple-mfd-i2c.h @@ -27,6 +27,7 @@ struct
>>   	simple_mfd_data { const struct regmap_config *regmap_config;
>>   	const struct mfd_cell *mfd_cell; size_t mfd_cell_size; +
>>   	unsigned int max_register; };
>>   
>>   #endif /* __MFD_SIMPLE_MFD_I2C_H */ -- 2.45.2
>>
> 

[PATCH v7 3/8] mfd: simple-mfd-i2c: add SpacemiT P1 support

[Alex Elder]

Enable support for the RTC and regulators found in the SpacemiT P1
PMIC.  Support is implemented by the simple I2C MFD driver.

The P1 PMIC is normally implemented with the SpacemiT K1 SoC.  This
PMIC provides 6 buck converters and 12 LDO regulators.  It also
implements a switch, watchdog timer, real-time clock, and more.
Initially its RTC and regulators are supported.

Signed-off-by: Alex Elder <elder@riscstar.com>
---
 drivers/mfd/Kconfig          | 11 +++++++++++
 drivers/mfd/simple-mfd-i2c.c | 12 ++++++++++++
 2 files changed, 23 insertions(+)

diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index 6fb3768e3d71c..01805c3eec57d 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -1182,6 +1182,17 @@ config MFD_QCOM_RPM
 	  Say M here if you want to include support for the Qualcomm RPM as a
 	  module. This will build a module called "qcom_rpm".
 
+config MFD_SPACEMIT_P1
+	tristate "SpacemiT P1 PMIC"
+	depends on I2C
+	select MFD_SIMPLE_MFD_I2C
+	help
+	  This option supports the I2C-based SpacemiT P1 PMIC, which
+	  contains regulators, a power switch, GPIOs, an RTC, and more.
+	  This option is selected when any of the supported sub-devices
+	  is configured.  The basic functionality is implemented by the
+	  simple MFD I2C driver.
+
 config MFD_SPMI_PMIC
 	tristate "Qualcomm SPMI PMICs"
 	depends on ARCH_QCOM || COMPILE_TEST
diff --git a/drivers/mfd/simple-mfd-i2c.c b/drivers/mfd/simple-mfd-i2c.c
index 3f959f4f98261..a8f658eaf4108 100644
--- a/drivers/mfd/simple-mfd-i2c.c
+++ b/drivers/mfd/simple-mfd-i2c.c
@@ -102,12 +102,24 @@ static const struct simple_mfd_data maxim_mon_max77705 = {
 	.mfd_cell_size = ARRAY_SIZE(max77705_sensor_cells),
 };
 
+static const struct mfd_cell spacemit_p1_cells[] = {
+	{ .name = "spacemit-p1-regulator", },
+	{ .name = "spacemit-p1-rtc", },
+};
+
+static const struct simple_mfd_data spacemit_p1 = {
+	.mfd_cell = spacemit_p1_cells,
+	.mfd_cell_size = ARRAY_SIZE(spacemit_p1_cells),
+	.max_register = 0xaa,
+};
+
 static const struct of_device_id simple_mfd_i2c_of_match[] = {
 	{ .compatible = "kontron,sl28cpld" },
 	{ .compatible = "silergy,sy7636a", .data = &silergy_sy7636a},
 	{ .compatible = "maxim,max5970", .data = &maxim_max5970},
 	{ .compatible = "maxim,max5978", .data = &maxim_max5970},
 	{ .compatible = "maxim,max77705-battery", .data = &maxim_mon_max77705},
+	{ .compatible = "spacemit,p1", .data = &spacemit_p1, },
 	{}
 };
 MODULE_DEVICE_TABLE(of, simple_mfd_i2c_of_match);
-- 
2.45.2

Re: [PATCH v7 3/8] mfd: simple-mfd-i2c: add SpacemiT P1 support

[Lee Jones]

On Wed, 02 Jul 2025, Alex Elder wrote:

> Enable support for the RTC and regulators found in the SpacemiT P1
> PMIC.  Support is implemented by the simple I2C MFD driver.
> 
> The P1 PMIC is normally implemented with the SpacemiT K1 SoC.  This
> PMIC provides 6 buck converters and 12 LDO regulators.  It also
> implements a switch, watchdog timer, real-time clock, and more.
> Initially its RTC and regulators are supported.
> 
> Signed-off-by: Alex Elder <elder@riscstar.com>
> ---
>  drivers/mfd/Kconfig          | 11 +++++++++++
>  drivers/mfd/simple-mfd-i2c.c | 12 ++++++++++++
>  2 files changed, 23 insertions(+)

Looks good.

-- 
Lee Jones [李琼斯]

[PATCH v7 4/8] regulator: spacemit: support SpacemiT P1 regulators

[Alex Elder]

Add support for the regulators found in the SpacemiT P1 PMIC.  This
PMIC provides 6 buck converters and 12 LDO regulators.

The PMIC is implemented as a multi-function device.  These regulators
are probed based on this driver being named in a MFD cell in the simple
MFD I2C driver.

Signed-off-by: Alex Elder <elder@riscstar.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
---
 drivers/regulator/Kconfig       |  12 +++
 drivers/regulator/Makefile      |   1 +
 drivers/regulator/spacemit-p1.c | 157 ++++++++++++++++++++++++++++++++
 3 files changed, 170 insertions(+)
 create mode 100644 drivers/regulator/spacemit-p1.c

diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 7423954153b07..3e7feeebf8aca 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -1395,6 +1395,18 @@ config REGULATOR_SLG51000
 	  The SLG51000 is seven compact and customizable low dropout
 	  regulators.
 
+config REGULATOR_SPACEMIT_P1
+	tristate "SpacemiT P1 regulators"
+	depends on ARCH_SPACEMIT || COMPILE_TEST
+	select MFD_SPACEMIT_P1
+	default ARCH_SPACEMIT
+	help
+	  Enable support for regulators implemented by the SpacemiT P1
+	  power controller.  The P1 implements 6 high-efficiency buck
+	  converters and 12 programmable LDO regulators.  To compile this
+	  driver as a module, choose M here.  The module will be called
+	  "spacemit-pmic".
+
 config REGULATOR_STM32_BOOSTER
 	tristate "STMicroelectronics STM32 BOOSTER"
 	depends on ARCH_STM32 || COMPILE_TEST
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index be98b29d6675d..278f5b8d1c7d7 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -162,6 +162,7 @@ obj-$(CONFIG_REGULATOR_S5M8767) += s5m8767.o
 obj-$(CONFIG_REGULATOR_SC2731) += sc2731-regulator.o
 obj-$(CONFIG_REGULATOR_SKY81452) += sky81452-regulator.o
 obj-$(CONFIG_REGULATOR_SLG51000) += slg51000-regulator.o
+obj-$(CONFIG_REGULATOR_SPACEMIT_P1) += spacemit-p1.o
 obj-$(CONFIG_REGULATOR_STM32_BOOSTER) += stm32-booster.o
 obj-$(CONFIG_REGULATOR_STM32_VREFBUF) += stm32-vrefbuf.o
 obj-$(CONFIG_REGULATOR_STM32_PWR) += stm32-pwr.o
diff --git a/drivers/regulator/spacemit-p1.c b/drivers/regulator/spacemit-p1.c
new file mode 100644
index 0000000000000..d437e6738ea1e
--- /dev/null
+++ b/drivers/regulator/spacemit-p1.c
@@ -0,0 +1,157 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Driver for regulators found in the SpacemiT P1 PMIC
+ *
+ * Copyright (C) 2025 by RISCstar Solutions Corporation.  All rights reserved.
+ * Derived from code from SpacemiT.
+ *	Copyright (c) 2023, SPACEMIT Co., Ltd
+ */
+
+#include <linux/array_size.h>
+#include <linux/bits.h>
+#include <linux/device.h>
+#include <linux/linear_range.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/driver.h>
+
+#define MOD_NAME	"spacemit-p1-regulator"
+
+enum p1_regulator_id {
+	P1_BUCK1,
+	P1_BUCK2,
+	P1_BUCK3,
+	P1_BUCK4,
+	P1_BUCK5,
+	P1_BUCK6,
+
+	P1_ALDO1,
+	P1_ALDO2,
+	P1_ALDO3,
+	P1_ALDO4,
+
+	P1_DLDO1,
+	P1_DLDO2,
+	P1_DLDO3,
+	P1_DLDO4,
+	P1_DLDO5,
+	P1_DLDO6,
+	P1_DLDO7,
+};
+
+static const struct regulator_ops p1_regulator_ops = {
+	.list_voltage		= regulator_list_voltage_linear_range,
+	.get_voltage_sel	= regulator_get_voltage_sel_regmap,
+	.set_voltage_sel	= regulator_set_voltage_sel_regmap,
+	.set_voltage_time_sel   = regulator_set_voltage_time_sel,
+	.enable			= regulator_enable_regmap,
+	.disable		= regulator_disable_regmap,
+	.is_enabled		= regulator_is_enabled_regmap,
+};
+
+/* Selector value 255 can be used to disable the buck converter on sleep */
+static const struct linear_range p1_buck_ranges[] = {
+	REGULATOR_LINEAR_RANGE(500000, 0, 170, 5000),
+	REGULATOR_LINEAR_RANGE(1375000, 171, 254, 25000),
+};
+
+/* Selector value 0 can be used for suspend */
+static const struct linear_range p1_ldo_ranges[] = {
+	REGULATOR_LINEAR_RANGE(500000, 11, 127, 25000),
+};
+
+/* These define the voltage selector field for buck and LDO regulators */
+#define BUCK_MASK		GENMASK(7, 0)
+#define LDO_MASK		GENMASK(6, 0)
+
+#define P1_ID(_TYPE, _n)	P1_ ## _TYPE ## _n
+#define P1_ENABLE_REG(_off, _n)	((_off) + 3 * ((_n) - 1))
+
+#define P1_REG_DESC(_TYPE, _type, _n, _s, _off, _mask, _nv, _ranges)	\
+	{								\
+		.name			= #_type #_n,			\
+		.supply_name		= _s,				\
+		.of_match		= of_match_ptr(#_type #_n),	\
+		.regulators_node	= of_match_ptr("regulators"),	\
+		.id			= P1_ID(_TYPE, _n),		\
+		.n_voltages		= _nv,				\
+		.ops			= &p1_regulator_ops,		\
+		.owner			= THIS_MODULE,			\
+		.linear_ranges		= _ranges,			\
+		.n_linear_ranges	= ARRAY_SIZE(_ranges),		\
+		.vsel_reg		= P1_ENABLE_REG(_off, _n) + 1,	\
+		.vsel_mask		= _mask,			\
+		.enable_reg		= P1_ENABLE_REG(_off, _n),	\
+		.enable_mask		= BIT(0),			\
+	}
+
+#define P1_BUCK_DESC(_n) \
+	P1_REG_DESC(BUCK, buck, _n, "vcc", 0x47, BUCK_MASK, 254, p1_buck_ranges)
+
+#define P1_ALDO_DESC(_n) \
+	P1_REG_DESC(ALDO, aldo, _n, "vcc", 0x5b, LDO_MASK, 117, p1_ldo_ranges)
+
+#define P1_DLDO_DESC(_n) \
+	P1_REG_DESC(DLDO, dldo, _n, "buck5", 0x67, LDO_MASK, 117, p1_ldo_ranges)
+
+static const struct regulator_desc p1_regulator_desc[] = {
+	P1_BUCK_DESC(1),
+	P1_BUCK_DESC(2),
+	P1_BUCK_DESC(3),
+	P1_BUCK_DESC(4),
+	P1_BUCK_DESC(5),
+	P1_BUCK_DESC(6),
+
+	P1_ALDO_DESC(1),
+	P1_ALDO_DESC(2),
+	P1_ALDO_DESC(3),
+	P1_ALDO_DESC(4),
+
+	P1_DLDO_DESC(1),
+	P1_DLDO_DESC(2),
+	P1_DLDO_DESC(3),
+	P1_DLDO_DESC(4),
+	P1_DLDO_DESC(5),
+	P1_DLDO_DESC(6),
+	P1_DLDO_DESC(7),
+};
+
+static int p1_regulator_probe(struct platform_device *pdev)
+{
+	struct regulator_config config = { };
+	struct device *dev = &pdev->dev;
+	u32 i;
+
+	/*
+	 * The parent device (PMIC) owns the regmap.  Since we don't
+	 * provide one in the config structure, that one will be used.
+	 */
+	config.dev = dev->parent;
+
+	for (i = 0; i < ARRAY_SIZE(p1_regulator_desc); i++) {
+		const struct regulator_desc *desc = &p1_regulator_desc[i];
+		struct regulator_dev *rdev;
+
+		rdev = devm_regulator_register(dev, desc, &config);
+		if (IS_ERR(rdev))
+			return dev_err_probe(dev, PTR_ERR(rdev),
+					     "error registering regulator %s\n",
+					     desc->name);
+	}
+
+	return 0;
+}
+
+static struct platform_driver p1_regulator_driver = {
+	.probe = p1_regulator_probe,
+	.driver = {
+		.name = MOD_NAME,
+	},
+};
+
+module_platform_driver(p1_regulator_driver);
+
+MODULE_DESCRIPTION("SpacemiT P1 regulator driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:" MOD_NAME);
-- 
2.45.2

[PATCH v7 5/8] rtc: spacemit: support the SpacemiT P1 RTC

[Alex Elder]

Add support for the RTC found in the SpacemiT P1 PMIC.  Initially
only setting and reading the time are supported.

The PMIC is implemented as a multi-function device.  This RTC is
probed based on this driver being named in a MFD cell in the simple
MFD I2C driver.

Signed-off-by: Alex Elder <elder@riscstar.com>
---
 drivers/rtc/Kconfig           |  10 ++
 drivers/rtc/Makefile          |   1 +
 drivers/rtc/rtc-spacemit-p1.c | 167 ++++++++++++++++++++++++++++++++++
 3 files changed, 178 insertions(+)
 create mode 100644 drivers/rtc/rtc-spacemit-p1.c

diff --git a/drivers/rtc/Kconfig b/drivers/rtc/Kconfig
index 9aec922613cec..93620f2c9b29c 100644
--- a/drivers/rtc/Kconfig
+++ b/drivers/rtc/Kconfig
@@ -406,6 +406,16 @@ config RTC_DRV_MAX77686
 	  This driver can also be built as a module. If so, the module
 	  will be called rtc-max77686.
 
+config RTC_DRV_SPACEMIT_P1
+	tristate "SpacemiT P1 RTC"
+	depends on ARCH_SPACEMIT || COMPILE_TEST
+	select MFD_SPACEMIT_P1
+	default ARCH_SPACEMIT
+	help
+	  Enable support for the RTC function in the SpacemiT P1 PMIC.
+	  This driver can also be built as a module, which will be called
+	  "spacemit-p1-rtc".
+
 config RTC_DRV_NCT3018Y
 	tristate "Nuvoton NCT3018Y"
 	depends on OF
diff --git a/drivers/rtc/Makefile b/drivers/rtc/Makefile
index 4619aa2ac4697..a24ff6ad5ca58 100644
--- a/drivers/rtc/Makefile
+++ b/drivers/rtc/Makefile
@@ -171,6 +171,7 @@ obj-$(CONFIG_RTC_DRV_SD2405AL)	+= rtc-sd2405al.o
 obj-$(CONFIG_RTC_DRV_SD3078)	+= rtc-sd3078.o
 obj-$(CONFIG_RTC_DRV_SH)	+= rtc-sh.o
 obj-$(CONFIG_RTC_DRV_SNVS)	+= rtc-snvs.o
+obj-$(CONFIG_RTC_DRV_SPACEMIT_P1)	+= rtc-spacemit-p1.o
 obj-$(CONFIG_RTC_DRV_SPEAR)	+= rtc-spear.o
 obj-$(CONFIG_RTC_DRV_STARFIRE)	+= rtc-starfire.o
 obj-$(CONFIG_RTC_DRV_STK17TA8)	+= rtc-stk17ta8.o
diff --git a/drivers/rtc/rtc-spacemit-p1.c b/drivers/rtc/rtc-spacemit-p1.c
new file mode 100644
index 0000000000000..5f1bcca00549c
--- /dev/null
+++ b/drivers/rtc/rtc-spacemit-p1.c
@@ -0,0 +1,167 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Driver for the RTC found in the SpacemiT P1 PMIC
+ *
+ * Copyright (C) 2025 by RISCstar Solutions Corporation.  All rights reserved.
+ */
+
+#include <linux/bits.h>
+#include <linux/device.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/rtc.h>
+
+#define MOD_NAME	"spacemit-p1-rtc"
+
+/*
+ * Six consecutive 1-byte registers hold the seconds, minutes, hours,
+ * day-of-month, month, and year (respectively).
+ *
+ * The range of values in these registers is:
+ *    seconds	0-59
+ *    minutes	0-59
+ *    hours	0-59
+ *    day	0-30 (struct tm is 1-31)
+ *    month	0-11
+ *    year	years since 2000 (struct tm is since 1900)
+ *
+ * Note that the day and month must be converted after reading and
+ * before writing.
+ */
+#define RTC_TIME		0x0d	/* Offset of the seconds register */
+
+#define RTC_CTRL		0x1d
+#define RTC_EN		BIT(2)
+
+/* Number of attempts to read a consistent time stamp before giving up */
+#define RTC_READ_TRIES		20	/* At least 1 */
+
+struct p1_rtc {
+	struct regmap *regmap;
+	struct rtc_device *rtc;
+};
+
+/*
+ * The P1 hardware documentation states that the register values are
+ * latched to ensure a consistent time snapshot within the registers,
+ * but these are in fact unstable due to a bug in the hardware design.
+ * So we loop until we get two identical readings.
+ */
+static int p1_rtc_read_time(struct device *dev, struct rtc_time *t)
+{
+	struct p1_rtc *p1 = dev_get_drvdata(dev);
+	struct regmap *regmap = p1->regmap;
+	u32 count = RTC_READ_TRIES;
+	u8 seconds;
+	u8 time[6];
+	int ret;
+
+	if (!regmap_test_bits(regmap, RTC_CTRL, RTC_EN))
+		return -ENODEV;		/* RTC is disabled */
+
+	ret = regmap_bulk_read(regmap, RTC_TIME, time, sizeof(time));
+	if (ret)
+		return ret;
+
+	do {
+		seconds = time[0];
+		ret = regmap_bulk_read(regmap, RTC_TIME, time, sizeof(time));
+		if (ret)
+			return ret;
+	} while (time[0] != seconds && --count);
+
+	if (!count)
+		return -EIO;		/* Unable to get a consistent result */
+
+	t->tm_sec = time[0] & GENMASK(5, 0);
+	t->tm_min = time[1] & GENMASK(5, 0);
+	t->tm_hour = time[2] & GENMASK(4, 0);
+	t->tm_mday = (time[3] & GENMASK(4, 0)) + 1;
+	t->tm_mon = time[4] & GENMASK(3, 0);
+	t->tm_year = (time[5] & GENMASK(5, 0)) + 100;
+
+	return 0;
+}
+
+/*
+ * The P1 hardware documentation states that values in the registers are
+ * latched so when written they represent a consistent time snapshot.
+ * Nevertheless, this is not guaranteed by the implementation, so we must
+ * disable the RTC while updating it.
+ */
+static int p1_rtc_set_time(struct device *dev, struct rtc_time *t)
+{
+	struct p1_rtc *p1 = dev_get_drvdata(dev);
+	struct regmap *regmap = p1->regmap;
+	u8 time[6];
+	int ret;
+
+	time[0] = t->tm_sec;
+	time[1] = t->tm_min;
+	time[2] = t->tm_hour;
+	time[3] = t->tm_mday - 1;
+	time[4] = t->tm_mon;
+	time[5] = t->tm_year - 100;
+
+	/* Disable the RTC to update; re-enable again when done */
+	ret = regmap_clear_bits(regmap, RTC_CTRL, RTC_EN);
+	if (ret)
+		return ret;
+
+	/* If something goes wrong, leave the RTC disabled */
+	ret = regmap_bulk_write(regmap, RTC_TIME, time, sizeof(time));
+	if (ret)
+		return ret;
+
+	return regmap_set_bits(regmap, RTC_CTRL, RTC_EN);
+}
+
+static const struct rtc_class_ops p1_rtc_class_ops = {
+	.read_time = p1_rtc_read_time,
+	.set_time = p1_rtc_set_time,
+};
+
+static int p1_rtc_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct rtc_device *rtc;
+	struct p1_rtc *p1;
+
+	p1 = devm_kzalloc(dev, sizeof(*p1), GFP_KERNEL);
+	if (!p1)
+		return -ENOMEM;
+	dev_set_drvdata(dev, p1);
+
+	p1->regmap = dev_get_regmap(dev->parent, NULL);
+	if (!p1->regmap)
+		return dev_err_probe(dev, -ENODEV, "failed to get regmap\n");
+
+	rtc = devm_rtc_allocate_device(dev);
+	if (IS_ERR(rtc))
+		return dev_err_probe(dev, PTR_ERR(rtc),
+				     "error allocating device\n");
+	p1->rtc = rtc;
+
+	rtc->ops = &p1_rtc_class_ops;
+	rtc->range_min = RTC_TIMESTAMP_BEGIN_2000;
+	rtc->range_max = RTC_TIMESTAMP_END_2063;
+
+	clear_bit(RTC_FEATURE_ALARM, rtc->features);
+	clear_bit(RTC_FEATURE_UPDATE_INTERRUPT, rtc->features);
+
+	return devm_rtc_register_device(rtc);
+}
+
+static struct platform_driver p1_rtc_driver = {
+	.probe = p1_rtc_probe,
+	.driver = {
+		.name = MOD_NAME,
+	},
+};
+
+module_platform_driver(p1_rtc_driver);
+
+MODULE_DESCRIPTION("SpacemiT P1 RTC driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:" MOD_NAME);
-- 
2.45.2

[PATCH v7 6/8] riscv: dts: spacemit: enable the i2c8 adapter

[Alex Elder]

Define properties for the I2C adapter that provides access to the
SpacemiT P1 PMIC.  Enable this adapter on the Banana Pi BPI-F3.

Signed-off-by: Alex Elder <elder@riscstar.com>
---
 arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts | 15 +++++++++++++++
 arch/riscv/boot/dts/spacemit/k1-pinctrl.dtsi    |  7 +++++++
 arch/riscv/boot/dts/spacemit/k1.dtsi            | 11 +++++++++++
 3 files changed, 33 insertions(+)

diff --git a/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts b/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts
index fe22c747c5012..7c9f91c88e01a 100644
--- a/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts
+++ b/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts
@@ -40,6 +40,21 @@ &emmc {
 	status = "okay";
 };
 
+&i2c8 {
+	pinctrl-0 = <&i2c8_cfg>;
+	pinctrl-names = "default";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	pmic@41 {
+		compatible = "spacemit,p1";
+		reg = <0x41>;
+		interrupts = <64>;
+		status = "okay";
+	};
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_2_cfg>;
diff --git a/arch/riscv/boot/dts/spacemit/k1-pinctrl.dtsi b/arch/riscv/boot/dts/spacemit/k1-pinctrl.dtsi
index 283663647a86f..9d6d4503fe751 100644
--- a/arch/riscv/boot/dts/spacemit/k1-pinctrl.dtsi
+++ b/arch/riscv/boot/dts/spacemit/k1-pinctrl.dtsi
@@ -11,6 +11,13 @@
 #define K1_GPIO(x)	(x / 32) (x % 32)
 
 &pinctrl {
+	i2c8_cfg: i2c8-cfg {
+		i2c8-0-pins {
+			pinmux = <K1_PADCONF(93, 0)>,	/* PWR_SCL */
+				 <K1_PADCONF(94, 0)>;	/* PWR_SDA */
+		};
+	};
+
 	uart0_2_cfg: uart0-2-cfg {
 		uart0-2-pins {
 			pinmux = <K1_PADCONF(68, 2)>,
diff --git a/arch/riscv/boot/dts/spacemit/k1.dtsi b/arch/riscv/boot/dts/spacemit/k1.dtsi
index 14097f1f6f447..a85239e8e430b 100644
--- a/arch/riscv/boot/dts/spacemit/k1.dtsi
+++ b/arch/riscv/boot/dts/spacemit/k1.dtsi
@@ -483,6 +483,17 @@ gpio: gpio@d4019000 {
 				      <&pinctrl 3 0 96 32>;
 		};
 
+		i2c8: i2c@d401d800 {
+			compatible = "spacemit,k1-i2c";
+			reg = <0x0 0xd401d800 0x0 0x38>;
+			interrupts = <19>;
+			clocks = <&syscon_apbc CLK_TWSI8>,
+				 <&syscon_apbc CLK_TWSI8_BUS>;
+			clock-names = "func", "bus";
+			clock-frequency = <400000>;
+			status = "disabled";
+		};
+
 		pinctrl: pinctrl@d401e000 {
 			compatible = "spacemit,k1-pinctrl";
 			reg = <0x0 0xd401e000 0x0 0x400>;
-- 
2.45.2

[PATCH v7 7/8] riscv: dts: spacemit: define fixed regulators

[Alex Elder]

Define the DC power input and the 4v power as fixed supplies in the
Banana Pi BPI-F3.

Signed-off-by: Alex Elder <elder@riscstar.com>
---
 .../boot/dts/spacemit/k1-bananapi-f3.dts      | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)

diff --git a/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts b/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts
index 7c9f91c88e01a..a1c184b814262 100644
--- a/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts
+++ b/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts
@@ -28,6 +28,25 @@ led1 {
 			default-state = "on";
 		};
 	};
+
+	reg_dc_in: dc-in-12v {
+		compatible = "regulator-fixed";
+		regulator-name = "dc_in_12v";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_vcc_4v: vcc-4v {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_4v";
+		regulator-min-microvolt = <4000000>;
+		regulator-max-microvolt = <4000000>;
+		regulator-boot-on;
+		regulator-always-on;
+		vin-supply = <&reg_dc_in>;
+	};
 };
 
 &emmc {
-- 
2.45.2

[PATCH v7 8/8] riscv: dts: spacemit: define regulator constraints

[Alex Elder]

Define basic constraints for the regulators in the SpacemiT P1 PMIC,
as implemented in the Banana Pi BPI-F3.

Signed-off-by: Alex Elder <elder@riscstar.com>
---
 .../boot/dts/spacemit/k1-bananapi-f3.dts      | 104 ++++++++++++++++++
 1 file changed, 104 insertions(+)

diff --git a/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts b/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts
index a1c184b814262..83907cc1d5ccf 100644
--- a/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts
+++ b/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts
@@ -70,7 +70,111 @@ pmic@41 {
 		compatible = "spacemit,p1";
 		reg = <0x41>;
 		interrupts = <64>;
+		vin-supply = <&reg_vcc_4v>;
 		status = "okay";
+
+		regulators {
+			buck1 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3450000>;
+				regulator-ramp-delay = <5000>;
+				regulator-always-on;
+			};
+
+			buck2 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3450000>;
+				regulator-ramp-delay = <5000>;
+				regulator-always-on;
+			};
+
+			buck3 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-ramp-delay = <5000>;
+				regulator-always-on;
+			};
+
+			buck4 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-ramp-delay = <5000>;
+				regulator-always-on;
+			};
+
+			buck5 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3450000>;
+				regulator-ramp-delay = <5000>;
+				regulator-always-on;
+			};
+
+			buck6 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3450000>;
+				regulator-ramp-delay = <5000>;
+				regulator-always-on;
+			};
+
+			aldo1 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3400000>;
+				regulator-boot-on;
+			};
+
+			aldo2 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3400000>;
+			};
+
+			aldo3 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3400000>;
+			};
+
+			aldo4 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3400000>;
+			};
+
+			dldo1 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3400000>;
+				regulator-boot-on;
+			};
+
+			dldo2 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3400000>;
+			};
+
+			dldo3 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3400000>;
+			};
+
+			dldo4 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3400000>;
+				regulator-always-on;
+			};
+
+			dldo5 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3400000>;
+			};
+
+			dldo6 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3400000>;
+				regulator-always-on;
+			};
+
+			dldo7 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3400000>;
+			};
+		};
 	};
 };
 
-- 
2.45.2