From: Ben Zong-You Xie <ben717@andestech.com>
Cc: <arnd@arndb.de>, <paul.walmsley@sifive.com>, <palmer@dabbelt.com>,
<aou@eecs.berkeley.edu>, <alex@ghiti.fr>, <robh@kernel.org>,
<krzk+dt@kernel.org>, <conor+dt@kernel.org>, <tglx@linutronix.de>,
<daniel.lezcano@linaro.org>,
<prabhakar.mahadev-lad.rj@bp.renesas.com>,
<devicetree@vger.kernel.org>, <linux-riscv@lists.infradead.org>,
<linux-kernel@vger.kernel.org>, <soc@lists.linux.dev>,
<tim609@andestech.com>, Ben Zong-You Xie <ben717@andestech.com>
Subject: [PATCH v2 6/9] riscv: dts: andes: add QiLai SoC device tree
Date: Fri, 11 Jul 2025 21:30:22 +0800 [thread overview]
Message-ID: <20250711133025.2192404-7-ben717@andestech.com> (raw)
In-Reply-To: <20250711133025.2192404-1-ben717@andestech.com>
Introduce the initial device tree support for the Andes QiLai SoC.
For further information, you can refer to [1].
[1] https://www.andestech.com/en/products-solutions/andeshape-platforms/qilai-chip/
Signed-off-by: Ben Zong-You Xie <ben717@andestech.com>
---
arch/riscv/boot/dts/andes/qilai.dtsi | 186 +++++++++++++++++++++++++++
1 file changed, 186 insertions(+)
create mode 100644 arch/riscv/boot/dts/andes/qilai.dtsi
diff --git a/arch/riscv/boot/dts/andes/qilai.dtsi b/arch/riscv/boot/dts/andes/qilai.dtsi
new file mode 100644
index 000000000000..de3de32f8c39
--- /dev/null
+++ b/arch/riscv/boot/dts/andes/qilai.dtsi
@@ -0,0 +1,186 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2025 Andes Technology Corporation. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ timebase-frequency = <62500000>;
+
+ cpu0: cpu@0 {
+ compatible = "andestech,ax45mp", "riscv";
+ device_type = "cpu";
+ reg = <0>;
+ riscv,isa-base = "rv64i";
+ riscv,isa-extensions = "i", "m", "a", "f", "d", "c",
+ "zicntr", "zicsr", "zifencei",
+ "zihpm", "xandespmu";
+ mmu-type = "riscv,sv39";
+ clock-frequency = <100000000>;
+ i-cache-size = <0x8000>;
+ i-cache-sets = <256>;
+ i-cache-line-size = <64>;
+ d-cache-size = <0x8000>;
+ d-cache-sets = <128>;
+ d-cache-line-size = <64>;
+ next-level-cache = <&l2_cache>;
+
+ cpu0_intc: interrupt-controller {
+ compatible = "andestech,cpu-intc", "riscv,cpu-intc";
+ #interrupt-cells = <1>;
+ interrupt-controller;
+ };
+ };
+
+ cpu1: cpu@1 {
+ compatible = "andestech,ax45mp", "riscv";
+ device_type = "cpu";
+ reg = <1>;
+ riscv,isa-base = "rv64i";
+ riscv,isa-extensions = "i", "m", "a", "f", "d", "c",
+ "zicntr", "zicsr", "zifencei",
+ "zihpm", "xandespmu";
+ mmu-type = "riscv,sv39";
+ clock-frequency = <100000000>;
+ i-cache-size = <0x8000>;
+ i-cache-sets = <256>;
+ i-cache-line-size = <64>;
+ d-cache-size = <0x8000>;
+ d-cache-sets = <128>;
+ d-cache-line-size = <64>;
+ next-level-cache = <&l2_cache>;
+
+ cpu1_intc: interrupt-controller {
+ compatible = "andestech,cpu-intc",
+ "riscv,cpu-intc";
+ #interrupt-cells = <1>;
+ interrupt-controller;
+ };
+ };
+
+ cpu2: cpu@2 {
+ compatible = "andestech,ax45mp", "riscv";
+ device_type = "cpu";
+ reg = <2>;
+ riscv,isa-base = "rv64i";
+ riscv,isa-extensions = "i", "m", "a", "f", "d", "c",
+ "zicntr", "zicsr", "zifencei",
+ "zihpm", "xandespmu";
+ mmu-type = "riscv,sv39";
+ clock-frequency = <100000000>;
+ i-cache-size = <0x8000>;
+ i-cache-sets = <256>;
+ i-cache-line-size = <64>;
+ d-cache-size = <0x8000>;
+ d-cache-sets = <128>;
+ d-cache-line-size = <64>;
+ next-level-cache = <&l2_cache>;
+
+ cpu2_intc: interrupt-controller {
+ compatible = "andestech,cpu-intc",
+ "riscv,cpu-intc";
+ #interrupt-cells = <1>;
+ interrupt-controller;
+ };
+ };
+
+ cpu3: cpu@3 {
+ compatible = "andestech,ax45mp", "riscv";
+ device_type = "cpu";
+ reg = <3>;
+ riscv,isa-base = "rv64i";
+ riscv,isa-extensions = "i", "m", "a", "f", "d", "c",
+ "zicntr", "zicsr", "zifencei",
+ "zihpm", "xandespmu";
+ mmu-type = "riscv,sv39";
+ clock-frequency = <100000000>;
+ i-cache-size = <0x8000>;
+ i-cache-sets = <256>;
+ i-cache-line-size = <64>;
+ d-cache-size = <0x8000>;
+ d-cache-sets = <128>;
+ d-cache-line-size = <64>;
+ next-level-cache = <&l2_cache>;
+
+ cpu3_intc: interrupt-controller {
+ compatible = "andestech,cpu-intc",
+ "riscv,cpu-intc";
+ #interrupt-cells = <1>;
+ interrupt-controller;
+ };
+ };
+ };
+
+ soc {
+ compatible = "simple-bus";
+ ranges;
+ interrupt-parent = <&plic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ plmt: timer@100000 {
+ compatible = "andestech,qilai-plmt", "andestech,plmt0";
+ reg = <0x0 0x00100000 0x0 0x100000>;
+ interrupts-extended = <&cpu0_intc 7>,
+ <&cpu1_intc 7>,
+ <&cpu2_intc 7>,
+ <&cpu3_intc 7>;
+ };
+
+ l2_cache: cache-controller@200000 {
+ compatible = "andestech,qilai-ax45mp-cache",
+ "andestech,ax45mp-cache", "cache";
+ reg = <0x0 0x00200000 0x0 0x100000>;
+ interrupts = <16 IRQ_TYPE_LEVEL_HIGH>;
+ cache-line-size = <64>;
+ cache-level = <2>;
+ cache-sets = <2048>;
+ cache-size = <0x200000>;
+ cache-unified;
+ };
+
+ plic_sw: interrupt-controller@400000 {
+ compatible = "andestech,qilai-plicsw",
+ "andestech,plicsw";
+ reg = <0x0 0x00400000 0x0 0x400000>;
+ interrupts-extended = <&cpu0_intc 3>,
+ <&cpu1_intc 3>,
+ <&cpu2_intc 3>,
+ <&cpu3_intc 3>;
+ };
+
+ plic: interrupt-controller@2000000 {
+ compatible = "andestech,qilai-plic",
+ "andestech,nceplic100";
+ reg = <0x0 0x02000000 0x0 0x2000000>;
+ #address-cells = <0>;
+ #interrupt-cells = <2>;
+ interrupt-controller;
+ interrupts-extended = <&cpu0_intc 11>, <&cpu0_intc 9>,
+ <&cpu1_intc 11>, <&cpu1_intc 9>,
+ <&cpu2_intc 11>, <&cpu2_intc 9>,
+ <&cpu3_intc 11>, <&cpu3_intc 9>;
+ riscv,ndev = <71>;
+ };
+
+ uart0: serial@30300000 {
+ compatible = "andestech,uart16550", "ns16550a";
+ reg = <0x0 0x30300000 0x0 0x100000>;
+ interrupts = <9 IRQ_TYPE_LEVEL_HIGH>;
+ clock-frequency = <50000000>;
+ reg-offset = <32>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ no-loopback-test;
+ };
+ };
+};
--
2.34.1
next prev parent reply other threads:[~2025-07-11 13:31 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-07-11 13:30 [PATCH v2 0/9] add Voyager board support Ben Zong-You Xie
2025-07-11 13:30 ` [PATCH v2 1/9] riscv: add Andes SoC family Kconfig support Ben Zong-You Xie
2025-07-11 13:30 ` [PATCH v2 2/9] dt-bindings: riscv: add Andes QiLai SoC and the Voyager board bindings Ben Zong-You Xie
2025-07-11 13:30 ` [PATCH v2 3/9] dt-bindings: interrupt-controller: add Andes QiLai PLIC Ben Zong-You Xie
2025-07-11 13:30 ` [PATCH v2 4/9] dt-bindings: interrupt-controller: add Andes machine-level software interrupt controller Ben Zong-You Xie
2025-07-11 13:30 ` [PATCH v2 5/9] dt-bindings: timer: add Andes machine timer Ben Zong-You Xie
2025-07-14 16:18 ` Daniel Lezcano
2025-07-11 13:30 ` Ben Zong-You Xie [this message]
2025-07-11 13:30 ` [PATCH v2 7/9] riscv: dts: andes: add Voyager board device tree Ben Zong-You Xie
2025-07-11 13:30 ` [PATCH v2 8/9] riscv: defconfig: enable Andes SoC Ben Zong-You Xie
2025-07-11 13:30 ` [PATCH v2 9/9] MAINTAINERS: Add entry for " Ben Zong-You Xie
2025-08-10 21:12 ` [PATCH v2 0/9] add Voyager board support patchwork-bot+linux-riscv
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20250711133025.2192404-7-ben717@andestech.com \
--to=ben717@andestech.com \
--cc=alex@ghiti.fr \
--cc=aou@eecs.berkeley.edu \
--cc=arnd@arndb.de \
--cc=conor+dt@kernel.org \
--cc=daniel.lezcano@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-riscv@lists.infradead.org \
--cc=palmer@dabbelt.com \
--cc=paul.walmsley@sifive.com \
--cc=prabhakar.mahadev-lad.rj@bp.renesas.com \
--cc=robh@kernel.org \
--cc=soc@lists.linux.dev \
--cc=tglx@linutronix.de \
--cc=tim609@andestech.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).