[PATCH v2 0/4] media: i2c: IMX355 for the Pixel 3a

[PATCH v2 0/4] media: i2c: IMX355 for the Pixel 3a

[Richard Acayan]

This adds support for the IMX355 in devicetree and adds support for the
Pixel 3a front camera.

This depends on https://lore.kernel.org/r/20250630224158.249726-2-mailingradian@gmail.com
because the GPIOs would go right next to the charging, if sorted
alphabetically.

Changes since v1 (20250630225944.320755-7-mailingradian@gmail.com):
- too much to have a complete list (1-4/4)
- squash camera orientation patch (4/4, previously 5/5)
- squash driver changes (2/4, previously 3/5)
- remove labelled endpoint node in sdm670.dtsi (3/4, 4/4)
- change init sequence to match other similar drivers (2/4)
- retrieve clock frequency from devicetree-defined clock (4/4)
- remove clock-frequency from dt-bindings (1/4)
- remove redundant descriptions of child nodes (1/4)
- switch initial drive of the reset GPIO to low (2/4)
- set mclk frequency to 19.2 MHz (4/4)
- add vdda-pll supply for camss (4/4)
- use common power on and off functions (2/4)
- use devm_clk_get_optional (2/4)
- remove extra layer when describing mclk pin (4/4)
- rename regulators (1/4, 2/4, 4/4)

Richard Acayan (4):
  dt-bindings: media: i2c: Add Sony IMX355
  media: i2c: imx355: Support devicetree and power management
  arm64: dts: qcom: sdm670: remove camss endpoint nodes
  arm64: dts: qcom: sdm670-google-sargo: add imx355 front camera

 .../bindings/media/i2c/sony,imx355.yaml       | 108 +++++++++++++
 .../boot/dts/qcom/sdm670-google-sargo.dts     | 116 ++++++++++++++
 arch/arm64/boot/dts/qcom/sdm670.dtsi          |  12 --
 drivers/media/i2c/imx355.c                    | 143 ++++++++++++++++--
 4 files changed, 355 insertions(+), 24 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/media/i2c/sony,imx355.yaml

-- 
2.50.1

[PATCH v2 1/4] dt-bindings: media: i2c: Add Sony IMX355

[Richard Acayan]

The IMX355 camera sensor is a camera sensor that can be found as the
front camera in some smartphones, such as the Pixel 3, Pixel 3 XL, Pixel
3a, and Pixel 3a XL. It already has a driver, but needs support for
device tree. Document the IMX355 to support defining it in device tree.

Signed-off-by: Richard Acayan <mailingradian@gmail.com>
---
 .../bindings/media/i2c/sony,imx355.yaml       | 108 ++++++++++++++++++
 1 file changed, 108 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/media/i2c/sony,imx355.yaml

diff --git a/Documentation/devicetree/bindings/media/i2c/sony,imx355.yaml b/Documentation/devicetree/bindings/media/i2c/sony,imx355.yaml
new file mode 100644
index 000000000000..989e8ddc3f95
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/sony,imx355.yaml
@@ -0,0 +1,108 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/sony,imx355.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Sony IMX355 Sensor
+
+maintainers:
+  - Richard Acayan <mailingradian@gmail.com>
+
+description:
+  The IMX355 sensor is a 3280x2464 image sensor, commonly found as the front
+  camera in smartphones.
+
+allOf:
+  - $ref: /schemas/media/video-interface-devices.yaml#
+
+properties:
+  compatible:
+    const: sony,imx355
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  clock-names:
+    items:
+      - const: mclk
+
+  avdd-supply:
+    description: Analog power supply.
+
+  dvdd-supply:
+    description: Digital power supply.
+
+  dovdd-supply:
+    description: Interface power supply.
+
+  reset-gpios:
+    maxItems: 1
+
+  port:
+    $ref: /schemas/graph.yaml#/$defs/port-base
+    additionalProperties: false
+
+    properties:
+      endpoint:
+        $ref: /schemas/media/video-interfaces.yaml
+        unevaluatedProperties: false
+
+        required:
+          - link-frequencies
+
+    required:
+      - endpoint
+
+unevaluatedProperties: false
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - port
+
+examples:
+  - |
+    #include <dt-bindings/clock/qcom,camcc-sdm845.h>
+    #include <dt-bindings/gpio/gpio.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        camera@1a {
+            compatible = "sony,imx355";
+            reg = <0x1a>;
+
+            clocks = <&camcc CAM_CC_MCLK2_CLK>;
+            clock-names = "mclk";
+
+            assigned-clocks = <&camcc CAM_CC_MCLK2_CLK>;
+            assigned-clock-rates = <24000000>;
+
+            reset-gpios = <&tlmm 9 GPIO_ACTIVE_HIGH>;
+
+            avdd-supply = <&cam_front_ldo>;
+            dvdd-supply = <&cam_front_ldo>;
+            dovdd-supply = <&cam_vio_ldo>;
+
+            pinctrl-names = "default";
+            pinctrl-0 = <&cam_front_default>;
+
+            rotation = <270>;
+            orientation = <0>;
+
+            port {
+                cam_front_endpoint: endpoint {
+                    data-lanes = <0 1 2 3>;
+                    link-frequencies = /bits/ 64 <360000000>;
+                    remote-endpoint = <&camss_endpoint1>;
+                };
+            };
+        };
+    };
-- 
2.50.1

Re: [PATCH v2 1/4] dt-bindings: media: i2c: Add Sony IMX355

[Krzysztof Kozlowski]

On Mon, Jul 14, 2025 at 05:02:29PM -0400, Richard Acayan wrote:
> +  avdd-supply:
> +    description: Analog power supply.
> +
> +  dvdd-supply:
> +    description: Digital power supply.
> +
> +  dovdd-supply:
> +    description: Interface power supply.
> +
> +  reset-gpios:
> +    maxItems: 1
> +
> +  port:
> +    $ref: /schemas/graph.yaml#/$defs/port-base
> +    additionalProperties: false
> +
> +    properties:
> +      endpoint:
> +        $ref: /schemas/media/video-interfaces.yaml
> +        unevaluatedProperties: false
> +
> +        required:
> +          - link-frequencies
> +
> +    required:
> +      - endpoint
> +
> +unevaluatedProperties: false

Still wrongly placed. Look at example schema or other bindings, this
goes after required.

> +
> +required:
> +  - compatible
> +  - reg
> +  - clocks

Still missing supplies. Hardware cannot operate without power. Please
check your datasheet which will describe which supplies are optional.

Best regards,
Krzysztof

Re: [PATCH v2 1/4] dt-bindings: media: i2c: Add Sony IMX355

[Richard Acayan]

On Tue, Jul 15, 2025 at 10:27:54AM +0200, Krzysztof Kozlowski wrote:
> On Mon, Jul 14, 2025 at 05:02:29PM -0400, Richard Acayan wrote:
(snip)
> > +
> > +required:
> > +  - compatible
> > +  - reg
> > +  - clocks
> 
> Still missing supplies. Hardware cannot operate without power. Please
> check your datasheet which will describe which supplies are optional.

Maybe I shouldn't have pretended to have docs when changing the
supply names, but I don't know which ones are optional.

I'd assume at least dovdd/VIO is required.

Re: [PATCH v2 1/4] dt-bindings: media: i2c: Add Sony IMX355

[Krzysztof Kozlowski]

On 17/07/2025 23:51, Richard Acayan wrote:
> On Tue, Jul 15, 2025 at 10:27:54AM +0200, Krzysztof Kozlowski wrote:
>> On Mon, Jul 14, 2025 at 05:02:29PM -0400, Richard Acayan wrote:
> (snip)
>>> +
>>> +required:
>>> +  - compatible
>>> +  - reg
>>> +  - clocks
>>
>> Still missing supplies. Hardware cannot operate without power. Please
>> check your datasheet which will describe which supplies are optional.
> 
> Maybe I shouldn't have pretended to have docs when changing the
> supply names, but I don't know which ones are optional.
> 
> I'd assume at least dovdd/VIO is required.

Then all of them are usually required.

Best regards,
Krzysztof

[PATCH v2 2/4] media: i2c: imx355: Support devicetree and power management

[Richard Acayan]

A device tree compatible makes it possible for this driver to be used on
Open Firmware devices. Initialization of power-managed resources such as
the reset GPIO and voltage regulators can be specified in the device
tree and handled by the driver. Add support for this so the Pixel 3a can
use the driver.

Signed-off-by: Richard Acayan <mailingradian@gmail.com>
---
 drivers/media/i2c/imx355.c | 143 +++++++++++++++++++++++++++++++++----
 1 file changed, 131 insertions(+), 12 deletions(-)

diff --git a/drivers/media/i2c/imx355.c b/drivers/media/i2c/imx355.c
index b2dce67c0b6b..6244e1a5876f 100644
--- a/drivers/media/i2c/imx355.c
+++ b/drivers/media/i2c/imx355.c
@@ -3,9 +3,14 @@
 
 #include <linux/unaligned.h>
 #include <linux/acpi.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
 #include <linux/i2c.h>
 #include <linux/module.h>
+#include <linux/of.h>
 #include <linux/pm_runtime.h>
+#include <linux/regulator/consumer.h>
 #include <media/v4l2-ctrls.h>
 #include <media/v4l2-device.h>
 #include <media/v4l2-event.h>
@@ -121,6 +126,16 @@ struct imx355 {
 	 * Protect access to sensor v4l2 controls.
 	 */
 	struct mutex mutex;
+
+	struct clk *mclk;
+	struct gpio_desc *reset_gpio;
+	struct regulator_bulk_data supplies[3];
+};
+
+static const char * const imx355_supply_names[] = {
+	"avdd",
+	"dvdd",
+	"dovdd",
 };
 
 static const struct imx355_reg imx355_global_regs[] = {
@@ -1516,6 +1531,58 @@ static const struct v4l2_subdev_internal_ops imx355_internal_ops = {
 	.open = imx355_open,
 };
 
+static int imx355_power_off(struct device *dev)
+{
+	struct i2c_client *client = container_of(dev, struct i2c_client, dev);
+	struct v4l2_subdev *sd = i2c_get_clientdata(client);
+	struct imx355 *imx355 = to_imx355(sd);
+
+	clk_disable_unprepare(imx355->mclk);
+
+	if (imx355->reset_gpio)
+		gpiod_set_value_cansleep(imx355->reset_gpio, 0);
+
+	regulator_bulk_disable(ARRAY_SIZE(imx355->supplies), imx355->supplies);
+
+	return 0;
+}
+
+static int imx355_power_on(struct device *dev)
+{
+	struct i2c_client *client = container_of(dev, struct i2c_client, dev);
+	struct v4l2_subdev *sd = i2c_get_clientdata(client);
+	struct imx355 *imx355 = to_imx355(sd);
+	int ret;
+
+	ret = clk_prepare_enable(imx355->mclk);
+	if (ret) {
+		dev_err(dev, "failed to enable clocks: %d\n", ret);
+		return ret;
+	}
+
+	ret = regulator_bulk_enable(ARRAY_SIZE(imx355->supplies),
+				    imx355->supplies);
+	if (ret) {
+		dev_err(dev, "failed to enable regulators: %d\n", ret);
+		goto error_disable_clocks;
+	}
+
+	if (imx355->reset_gpio) {
+		usleep_range(5000, 5100);
+		gpiod_set_value_cansleep(imx355->reset_gpio, 1);
+		usleep_range(8000, 8100);
+	}
+
+	return 0;
+
+error_disable_clocks:
+	clk_disable_unprepare(imx355->mclk);
+	return ret;
+}
+
+static DEFINE_RUNTIME_DEV_PM_OPS(imx355_pm_ops, imx355_power_off,
+				 imx355_power_on, NULL);
+
 /* Initialize control handlers */
 static int imx355_init_controls(struct imx355 *imx355)
 {
@@ -1623,7 +1690,7 @@ static int imx355_init_controls(struct imx355 *imx355)
 	return ret;
 }
 
-static struct imx355_hwcfg *imx355_get_hwcfg(struct device *dev)
+static struct imx355_hwcfg *imx355_get_hwcfg(struct device *dev, struct imx355 *imx355)
 {
 	struct imx355_hwcfg *cfg;
 	struct v4l2_fwnode_endpoint bus_cfg = {
@@ -1648,11 +1715,15 @@ static struct imx355_hwcfg *imx355_get_hwcfg(struct device *dev)
 	if (!cfg)
 		goto out_err;
 
-	ret = fwnode_property_read_u32(dev_fwnode(dev), "clock-frequency",
-				       &cfg->ext_clk);
-	if (ret) {
-		dev_err(dev, "can't get clock frequency");
-		goto out_err;
+	if (imx355->mclk) {
+		cfg->ext_clk = clk_get_rate(imx355->mclk);
+	} else {
+		ret = fwnode_property_read_u32(dev_fwnode(dev), "clock-frequency",
+					       &cfg->ext_clk);
+		if (ret) {
+			dev_err(dev, "can't get clock frequency");
+			goto out_err;
+		}
 	}
 
 	dev_dbg(dev, "ext clk: %d", cfg->ext_clk);
@@ -1683,6 +1754,7 @@ static struct imx355_hwcfg *imx355_get_hwcfg(struct device *dev)
 static int imx355_probe(struct i2c_client *client)
 {
 	struct imx355 *imx355;
+	size_t i;
 	int ret;
 
 	imx355 = devm_kzalloc(&client->dev, sizeof(*imx355), GFP_KERNEL);
@@ -1694,27 +1766,59 @@ static int imx355_probe(struct i2c_client *client)
 	/* Initialize subdev */
 	v4l2_i2c_subdev_init(&imx355->sd, client, &imx355_subdev_ops);
 
-	/* Check module identity */
-	ret = imx355_identify_module(imx355);
+	for (i = 0; i < ARRAY_SIZE(imx355_supply_names); i++)
+		imx355->supplies[i].supply = imx355_supply_names[i];
+
+	ret = devm_regulator_bulk_get(&client->dev,
+				      ARRAY_SIZE(imx355->supplies),
+				      imx355->supplies);
 	if (ret) {
-		dev_err(&client->dev, "failed to find sensor: %d", ret);
+		dev_err_probe(&client->dev, ret, "could not get regulators");
 		goto error_probe;
 	}
 
-	imx355->hwcfg = imx355_get_hwcfg(&client->dev);
+	imx355->reset_gpio = devm_gpiod_get_optional(&client->dev, "reset",
+						     GPIOD_OUT_LOW);
+	if (IS_ERR(imx355->reset_gpio)) {
+		ret = dev_err_probe(&client->dev, PTR_ERR(imx355->reset_gpio),
+				    "failed to get gpios");
+		goto error_probe;
+	}
+
+	imx355->mclk = devm_clk_get_optional(&client->dev, "mclk");
+	if (IS_ERR(imx355->mclk)) {
+		ret = dev_err_probe(&client->dev, PTR_ERR(imx355->mclk),
+				    "failed to get mclk");
+		goto error_probe;
+	}
+
+	imx355->hwcfg = imx355_get_hwcfg(&client->dev, imx355);
 	if (!imx355->hwcfg) {
 		dev_err(&client->dev, "failed to get hwcfg");
 		ret = -ENODEV;
 		goto error_probe;
 	}
 
+	ret = imx355_power_on(&client->dev);
+	if (ret) {
+		dev_err(&client->dev, "failed to power on sensor: %d", ret);
+		goto error_probe;
+	}
+
+	/* Check module identity */
+	ret = imx355_identify_module(imx355);
+	if (ret) {
+		dev_err(&client->dev, "failed to find sensor: %d", ret);
+		goto error_power_off;
+	}
+
 	/* Set default mode to max resolution */
 	imx355->cur_mode = &supported_modes[0];
 
 	ret = imx355_init_controls(imx355);
 	if (ret) {
 		dev_err(&client->dev, "failed to init controls: %d", ret);
-		goto error_probe;
+		goto error_power_off;
 	}
 
 	/* Initialize subdev */
@@ -1754,6 +1858,9 @@ static int imx355_probe(struct i2c_client *client)
 error_handler_free:
 	v4l2_ctrl_handler_free(imx355->sd.ctrl_handler);
 
+error_power_off:
+	imx355_power_off(&client->dev);
+
 error_probe:
 	mutex_destroy(&imx355->mutex);
 
@@ -1770,7 +1877,11 @@ static void imx355_remove(struct i2c_client *client)
 	v4l2_ctrl_handler_free(sd->ctrl_handler);
 
 	pm_runtime_disable(&client->dev);
-	pm_runtime_set_suspended(&client->dev);
+
+	if (!pm_runtime_status_suspended(&client->dev)) {
+		imx355_power_off(&client->dev);
+		pm_runtime_set_suspended(&client->dev);
+	}
 
 	mutex_destroy(&imx355->mutex);
 }
@@ -1781,10 +1892,18 @@ static const struct acpi_device_id imx355_acpi_ids[] __maybe_unused = {
 };
 MODULE_DEVICE_TABLE(acpi, imx355_acpi_ids);
 
+static const struct of_device_id imx355_match_table[] __maybe_unused = {
+	{ .compatible = "sony,imx355", },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, imx355_match_table);
+
 static struct i2c_driver imx355_i2c_driver = {
 	.driver = {
 		.name = "imx355",
 		.acpi_match_table = ACPI_PTR(imx355_acpi_ids),
+		.of_match_table = of_match_ptr(imx355_match_table),
+		.pm = &imx355_pm_ops,
 	},
 	.probe = imx355_probe,
 	.remove = imx355_remove,
-- 
2.50.1

Re: [PATCH v2 2/4] media: i2c: imx355: Support devicetree and power management

[Konrad Dybcio]

On 7/14/25 11:02 PM, Richard Acayan wrote:
> A device tree compatible makes it possible for this driver to be used on
> Open Firmware devices. Initialization of power-managed resources such as
> the reset GPIO and voltage regulators can be specified in the device
> tree and handled by the driver. Add support for this so the Pixel 3a can
> use the driver.
> 
> Signed-off-by: Richard Acayan <mailingradian@gmail.com>
> ---

[...]

> +static int imx355_power_off(struct device *dev)
> +{
> +	struct i2c_client *client = container_of(dev, struct i2c_client, dev);
> +	struct v4l2_subdev *sd = i2c_get_clientdata(client);
> +	struct imx355 *imx355 = to_imx355(sd);
> +
> +	clk_disable_unprepare(imx355->mclk);
> +
> +	if (imx355->reset_gpio)
> +		gpiod_set_value_cansleep(imx355->reset_gpio, 0);
> +
> +	regulator_bulk_disable(ARRAY_SIZE(imx355->supplies), imx355->supplies);

FWIW power_off is normally a mirror image of power_on (so one would expect
thissequence to be reset_gpio->regulator->clk)

[...]

> +static struct imx355_hwcfg *imx355_get_hwcfg(struct device *dev, struct imx355 *imx355)
>  {
>  	struct imx355_hwcfg *cfg;
>  	struct v4l2_fwnode_endpoint bus_cfg = {
> @@ -1648,11 +1715,15 @@ static struct imx355_hwcfg *imx355_get_hwcfg(struct device *dev)
>  	if (!cfg)
>  		goto out_err;
>  
> -	ret = fwnode_property_read_u32(dev_fwnode(dev), "clock-frequency",
> -				       &cfg->ext_clk);
> -	if (ret) {
> -		dev_err(dev, "can't get clock frequency");
> -		goto out_err;
> +	if (imx355->mclk) {
> +		cfg->ext_clk = clk_get_rate(imx355->mclk);

See:

<20250710174808.5361-1-laurent.pinchart@ideasonboard.com>

Konrad

[PATCH v2 3/4] arm64: dts: qcom: sdm670: remove camss endpoint nodes

[Richard Acayan]

There is no need to add these by default for all of SDM670. Originally,
they were added so there could be a label for each port. This is
unnecessary if the endpoints are all added in a fixup to the camss node.

Suggested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/488281f6-5e5d-4864-8220-63e2a0b2d7f2@linaro.org
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
---
 arch/arm64/boot/dts/qcom/sdm670.dtsi | 12 ------------
 1 file changed, 12 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sdm670.dtsi b/arch/arm64/boot/dts/qcom/sdm670.dtsi
index c33f3de779f6..c275089237e4 100644
--- a/arch/arm64/boot/dts/qcom/sdm670.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm670.dtsi
@@ -1768,26 +1768,14 @@ ports {
 
 				port@0 {
 					reg = <0>;
-
-					camss_endpoint0: endpoint {
-						status = "disabled";
-					};
 				};
 
 				port@1 {
 					reg = <1>;
-
-					camss_endpoint1: endpoint {
-						status = "disabled";
-					};
 				};
 
 				port@2 {
 					reg = <2>;
-
-					camss_endpoint2: endpoint {
-						status = "disabled";
-					};
 				};
 			};
 		};
-- 
2.50.1

[PATCH v2 4/4] arm64: dts: qcom: sdm670-google-sargo: add imx355 front camera

[Richard Acayan]

The Sony IMX355 is the front camera on the Pixel 3a, mounted in portrait
mode. It is connected to CSIPHY1 and CCI I2C1, and uses MCLK2. Add
support for it.

Co-developed-by: Robert Mader <robert.mader@collabora.com>
Signed-off-by: Robert Mader <robert.mader@collabora.com>
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
---
 .../boot/dts/qcom/sdm670-google-sargo.dts     | 116 ++++++++++++++++++
 1 file changed, 116 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sdm670-google-sargo.dts b/arch/arm64/boot/dts/qcom/sdm670-google-sargo.dts
index d01422844fbf..76751bf91c70 100644
--- a/arch/arm64/boot/dts/qcom/sdm670-google-sargo.dts
+++ b/arch/arm64/boot/dts/qcom/sdm670-google-sargo.dts
@@ -172,6 +172,34 @@ vreg_s2b_1p05: vreg-s2b-regulator {
 		regulator-min-microvolt = <1050000>;
 		regulator-max-microvolt = <1050000>;
 	};
+
+	cam_front_ldo: cam-front-ldo-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "cam_front_ldo";
+		regulator-min-microvolt = <1352000>;
+		regulator-max-microvolt = <1352000>;
+		regulator-enable-ramp-delay = <135>;
+
+		gpios = <&pm660l_gpios 4 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&cam_front_ldo_pin>;
+		pinctrl-names = "default";
+	};
+
+	cam_vio_ldo: cam-vio-ldo-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "cam_vio_ldo";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-enable-ramp-delay = <233>;
+
+		gpios = <&pm660_gpios 13 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&cam_vio_pin>;
+		pinctrl-names = "default";
+	};
 };
 
 &apps_rsc {
@@ -392,6 +420,64 @@ vreg_bob: bob {
 	};
 };
 
+&camss {
+	vdda-phy-supply = <&vreg_l1a_1p225>;
+	vdda-pll-supply = <&vreg_s6a_0p87>;
+
+	status = "okay";
+
+	ports {
+		port@1 {
+			camss_endpoint1: endpoint {
+				clock-lanes = <7>;
+				data-lanes = <0 1 2 3>;
+				remote-endpoint = <&cam_front_endpoint>;
+			};
+		};
+	};
+};
+
+&cci {
+	pinctrl-0 = <&cci1_default &cam_mclk_default>;
+	pinctrl-1 = <&cci1_sleep>;
+	pinctrl-names = "default", "sleep";
+
+	status = "okay";
+};
+
+&cci_i2c1 {
+	camera@1a {
+		compatible = "sony,imx355";
+		reg = <0x1a>;
+
+		clocks = <&camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "mclk";
+
+		assigned-clocks = <&camcc CAM_CC_MCLK2_CLK>;
+		assigned-clock-rates = <19200000>;
+
+		reset-gpios = <&tlmm 9 GPIO_ACTIVE_HIGH>;
+
+		avdd-supply = <&cam_front_ldo>;
+		dvdd-supply = <&cam_front_ldo>;
+		dovdd-supply = <&cam_vio_ldo>;
+
+		pinctrl-0 = <&cam_front_default>;
+		pinctrl-names = "default";
+
+		rotation = <270>;
+		orientation = <0>;
+
+		port {
+			cam_front_endpoint: endpoint {
+				data-lanes = <0 1 2 3>;
+				link-frequencies = /bits/ 64 <360000000>;
+				remote-endpoint = <&camss_endpoint1>;
+			};
+		};
+	};
+};
+
 &gcc {
 	protected-clocks = <GCC_QSPI_CORE_CLK>,
 			   <GCC_QSPI_CORE_CLK_SRC>,
@@ -491,6 +577,15 @@ &pm660_charger {
 	status = "okay";
 };
 
+&pm660_gpios {
+	cam_vio_pin: cam-vio-state {
+		pins = "gpio13";
+		function = "normal";
+		power-source = <PM8941_GPIO_VPH>;
+		output-low;
+	};
+};
+
 &pm660_rradc {
 	status = "okay";
 };
@@ -509,6 +604,13 @@ led-0 {
 };
 
 &pm660l_gpios {
+	cam_front_ldo_pin: cam-front-state {
+		pins = "gpio4";
+		function = "normal";
+		power-source = <PM8941_GPIO_VPH>;
+		output-low;
+	};
+
 	vol_up_pin: vol-up-state {
 		pins = "gpio7";
 		function = "normal";
@@ -548,6 +650,20 @@ &sdhc_1 {
 &tlmm {
 	gpio-reserved-ranges = <0 4>, <81 4>;
 
+	cam_front_default: cam-front-default-state {
+		pins = "gpio9";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	cam_mclk_default: cam-default-state {
+		pins = "gpio15";
+		function = "cam_mclk";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
 	panel_default: panel-default-state {
 		te-pins {
 			pins = "gpio10";
-- 
2.50.1

Re: [PATCH v2 4/4] arm64: dts: qcom: sdm670-google-sargo: add imx355 front camera

[Konrad Dybcio]

On 7/14/25 11:02 PM, Richard Acayan wrote:
> The Sony IMX355 is the front camera on the Pixel 3a, mounted in portrait
> mode. It is connected to CSIPHY1 and CCI I2C1, and uses MCLK2. Add
> support for it.
> 
> Co-developed-by: Robert Mader <robert.mader@collabora.com>
> Signed-off-by: Robert Mader <robert.mader@collabora.com>
> Signed-off-by: Richard Acayan <mailingradian@gmail.com>
> ---


> +&pm660_gpios {
> +	cam_vio_pin: cam-vio-state {
> +		pins = "gpio13";
> +		function = "normal";
> +		power-source = <PM8941_GPIO_VPH>;

This define is actually specific to PM8941.. I would assume that 0
is generally bound to VPH_PWR, but eeh, this is not what you want

Konrad

Re: [PATCH v2 0/4] media: i2c: IMX355 for the Pixel 3a

[Krzysztof Kozlowski]

On Mon, Jul 14, 2025 at 05:02:28PM -0400, Richard Acayan wrote:
> This adds support for the IMX355 in devicetree and adds support for the
> Pixel 3a front camera.
> 
> This depends on https://lore.kernel.org/r/20250630224158.249726-2-mailingradian@gmail.com
> because the GPIOs would go right next to the charging, if sorted
> alphabetically.
> 
> Changes since v1 (20250630225944.320755-7-mailingradian@gmail.com):

If doing this, please use lore links. It's one click for me. Above is
not, needs multiple steps to recover the discussion.

Or just use b4...

Best regards,
Krzysztof

Re: [PATCH v2 0/4] media: i2c: IMX355 for the Pixel 3a

[Konrad Dybcio]

On 7/14/25 11:02 PM, Richard Acayan wrote:
> This adds support for the IMX355 in devicetree and adds support for the
> Pixel 3a front camera.
> 
> This depends on https://lore.kernel.org/r/20250630224158.249726-2-mailingradian@gmail.com
> because the GPIOs would go right next to the charging, if sorted
> alphabetically.
> 
> Changes since v1 (20250630225944.320755-7-mailingradian@gmail.com):
> - too much to have a complete list (1-4/4)
> - squash camera orientation patch (4/4, previously 5/5)

if the patch indices changed between series, it may be easier
to refer to them as e.g.:

dt-bindings:
 - changed a to b
 - moved x to y

sargo dts:
 - pet some dogs
 - drank some water

Konrad

> - squash driver changes (2/4, previously 3/5)
> - remove labelled endpoint node in sdm670.dtsi (3/4, 4/4)
> - change init sequence to match other similar drivers (2/4)
> - retrieve clock frequency from devicetree-defined clock (4/4)
> - remove clock-frequency from dt-bindings (1/4)
> - remove redundant descriptions of child nodes (1/4)
> - switch initial drive of the reset GPIO to low (2/4)
> - set mclk frequency to 19.2 MHz (4/4)
> - add vdda-pll supply for camss (4/4)
> - use common power on and off functions (2/4)
> - use devm_clk_get_optional (2/4)
> - remove extra layer when describing mclk pin (4/4)
> - rename regulators (1/4, 2/4, 4/4)
> 
> Richard Acayan (4):
>   dt-bindings: media: i2c: Add Sony IMX355
>   media: i2c: imx355: Support devicetree and power management
>   arm64: dts: qcom: sdm670: remove camss endpoint nodes
>   arm64: dts: qcom: sdm670-google-sargo: add imx355 front camera
> 
>  .../bindings/media/i2c/sony,imx355.yaml       | 108 +++++++++++++
>  .../boot/dts/qcom/sdm670-google-sargo.dts     | 116 ++++++++++++++
>  arch/arm64/boot/dts/qcom/sdm670.dtsi          |  12 --
>  drivers/media/i2c/imx355.c                    | 143 ++++++++++++++++--
>  4 files changed, 355 insertions(+), 24 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/media/i2c/sony,imx355.yaml
>