[PATCH v3 0/2] drm: bridge: Add TI tmds181 and sn65dp159 driver

[PATCH v3 0/2] drm: bridge: Add TI tmds181 and sn65dp159 driver

[Mike Looijmans]

In the past I've seen (and contributed to) hacks that model the chips as
phy or even (really!) clock drivers. Since the chip usually sits between
a signal that is (almost) HDMI and a HDMI connector, I decided to stop
lying and write it as a DRM bridge driver.

Our experience with these chips is that they work best under manual control
enabling them only once the signal is active. At low resolutions (under 4k),
the optimal setting is usually to only use redriver mode. Setting the
termination to 150-300 Ohms improves EMC performance at lower resolutions,
hence the driver enables 75-150 Ohms for HDMI2 modes and defaults to
150-300 Ohm termination for other modes.


Changes in v3:
Fix duplicate links
Add vcc-supply and vdd-supply
Fix missing type for ti,slew-rate
Lower-case hex values and use defines for EYESCAN registers
Remove equalizer code (unlikely to be used)
Remove attributes (no longer useful, undocumented)
Fix build for 6.17 kernel
Use devm_drm_bridge_alloc
Sort includes and add linux/bitfield.h
Check chip type and complain on mismatch

Changes in v2:
Document driver specific bindings like slew-rate and threshold
Use atomic_enable/disable
Use #defines for bit fields in registers
Allow HDMI 2 compliance
Filter modes on clock range
Use cross-over pixel frequency instead of manual overides
Devicetree bindings according to standards

Mike Looijmans (2):
  dt-bindings: drm/bridge: ti-tmds181: Add TI TMDS181 and SN65DP159
    bindings
  drm: bridge: Add TI tmds181 and sn65dp159 driver

 .../bindings/display/bridge/ti,tmds181.yaml   | 150 +++++++
 drivers/gpu/drm/bridge/Kconfig                |  11 +
 drivers/gpu/drm/bridge/Makefile               |   1 +
 drivers/gpu/drm/bridge/ti-tmds181.c           | 409 ++++++++++++++++++
 4 files changed, 571 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/bridge/ti,tmds181.yaml
 create mode 100644 drivers/gpu/drm/bridge/ti-tmds181.c

-- 
2.43.0

base-commit: 53e760d8949895390e256e723e7ee46618310361
branch: drm-ti-tmds181

Met vriendelijke groet / kind regards,

Mike Looijmans
System Expert


TOPIC Embedded Products B.V.
Materiaalweg 4, 5681 RJ Best
The Netherlands

T: +31 (0) 499 33 69 69
E: mike.looijmans@topic.nl
W: www.topic.nl

Please consider the environment before printing this e-mail

[PATCH v3 1/2] dt-bindings: drm/bridge: ti-tmds181: Add TI TMDS181 and SN65DP159 bindings

[Mike Looijmans]

Add DT binding document for TI TMDS181 and SN65DP159 HDMI retimers.

The two chips have similar register maps, but different applications
(source vs. sink).

Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>

---

Changes in v3:
Fix duplicate links
Add vcc-supply and vdd-supply
Fix missing type for ti,slew-rate

Changes in v2:
Document driver specific bindings like slew-rate and threshold

 .../bindings/display/bridge/ti,tmds181.yaml   | 150 ++++++++++++++++++
 1 file changed, 150 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/bridge/ti,tmds181.yaml

diff --git a/Documentation/devicetree/bindings/display/bridge/ti,tmds181.yaml b/Documentation/devicetree/bindings/display/bridge/ti,tmds181.yaml
new file mode 100644
index 000000000000..7433e694fae0
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/bridge/ti,tmds181.yaml
@@ -0,0 +1,150 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/ti,tmds181.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: TMDS181 and SN65DP159 HDMI retimer/redriver chips
+
+maintainers:
+  - Mike Looijmans <mike.looijmans@topic.nl>
+
+description: |
+  Texas Instruments TMDS181 and SN65DP159 retimer and redriver chips.
+  https://www.ti.com/product/TMDS181
+  https://www.ti.com/product/SN65DP159
+
+properties:
+  compatible:
+    enum:
+      - ti,tmds181
+      - ti,sn65dp159
+
+  reg:
+    enum:
+      - 0x5b
+      - 0x5c
+      - 0x5d
+      - 0x5e
+
+  oe-gpios:
+    maxItems: 1
+    description: GPIO specifier for OE pin (active high).
+
+  vdd-supply:
+    description: Core power supply, 1.1V
+
+  vcc-supply:
+    description: IO power supply, 3.3V
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/$defs/port-base
+        unevaluatedProperties: false
+        description: Video port for HDMI (ish) input
+
+        properties:
+          endpoint:
+            $ref: /schemas/media/video-interfaces.yaml#
+            unevaluatedProperties: false
+
+      port@1:
+        $ref: /schemas/graph.yaml#/$defs/port-base
+        unevaluatedProperties: false
+        description: Video port for HDMI output (panel or bridge)
+
+        properties:
+          endpoint:
+            $ref: /schemas/media/video-interfaces.yaml#
+            unevaluatedProperties: false
+
+    required:
+      - port@0
+      - port@1
+
+  ti,source-mode:
+    type: boolean
+    description:
+      Force chip to operate in "source" mode. Allows to use
+      a TMDS181 chip (which defaults to sink) as cable driver.
+
+  ti,sink-mode:
+    type: boolean
+    description:
+      Force chip to operate in "sink" mode. Allows to use
+      a DP159 chip (defaults to source) for incoming signals.
+
+  ti,retimer-threshold-hz:
+    minimum: 25000000
+    maximum: 600000000
+    default: 200000000
+    description:
+      Cross-over point. Up until this pixel clock frequency
+      the chip remains in the low-power redriver mode. Above
+      the threshold the chip should operate in retimer mode.
+
+  ti,dvi-mode:
+    type: boolean
+    description: Makes the DP159 chip operate in DVI mode.
+
+  ti,slew-rate:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    minimum: 0
+    maximum: 3
+    default: 3
+    description: Set slew rate, 0 is slowest, 3 is fastest.
+
+  ti,disable-equalizer:
+    type: boolean
+    description: Disable the equalizer (to save power).
+
+  ti,adaptive-equalizer:
+    type: boolean
+    description: Set the equalizer to adaptive mode.
+
+required:
+  - compatible
+  - reg
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        bridge@5b {
+            compatible = "ti,sn65dp159";
+            reg = <0x5b>;
+
+            oe-gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
+
+            ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                port@0 {
+                    reg = <0>;
+
+                    endpoint {
+                        remote-endpoint = <&encoder_out>;
+                    };
+                };
+
+                port@1 {
+                    reg = <1>;
+
+                    endpoint {
+                        remote-endpoint = <&hdmi_connector_in>;
+                    };
+                };
+            };
+        };
+    };
-- 
2.43.0


Met vriendelijke groet / kind regards,

Mike Looijmans
System Expert


TOPIC Embedded Products B.V.
Materiaalweg 4, 5681 RJ Best
The Netherlands

T: +31 (0) 499 33 69 69
E: mike.looijmans@topic.nl
W: www.topic.nl

Please consider the environment before printing this e-mail