Re: [PATCH v4 3/5] dt-bindings: iio: adc: add ade9000

[Rob Herring <robh@kernel.org>]

On Fri, Aug 15, 2025 at 09:56:36AM +0000, Antoniu Miclaus wrote:
> Add devicetree bindings support for ade9000.
> 
> Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
> ---
> changes in v4:
>  - improve description formatting (remove unnecessary pipe symbols)
>  - move $ref to end and remove allOf section for cleaner structure
>  .../bindings/iio/adc/adi,ade9000.yaml         | 108 ++++++++++++++++++
>  1 file changed, 108 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/iio/adc/adi,ade9000.yaml
> 
> diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ade9000.yaml b/Documentation/devicetree/bindings/iio/adc/adi,ade9000.yaml
> new file mode 100644
> index 000000000000..bd374c0d57d4
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/iio/adc/adi,ade9000.yaml
> @@ -0,0 +1,108 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +# Copyright 2025 Analog Devices Inc.
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/iio/adc/adi,ade9000.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Analog Devices ADE9000 High Performance, Polyphase Energy Metering driver
> +
> +maintainers:
> +  - Antoniu Miclaus <antoniu.miclaus@analog.com>
> +
> +description: |
> +  The ADE9000 s a highly accurate, fully integrated, multiphase energy and power
> +  quality monitoring device. Superior analog performance and a digital signal
> +  processing (DSP) core enable accurate energy monitoring over a wide dynamic
> +  range. An integrated high end reference ensures low drift over temperature
> +  with a combined drift of less than ±25 ppm/°C maximum for the entire channel
> +  including a programmable gain amplifier (PGA) and an analog-to- digital
> +  converter (ADC).
> +
> +  https://www.analog.com/media/en/technical-documentation/data-sheets/ADE9000.pdf
> +
> +$ref: /schemas/spi/spi-peripheral-props.yaml#
> +
> +properties:
> +  compatible:
> +    enum:
> +      - adi,ade9000
> +
> +  reg:
> +    maxItems: 1
> +
> +  spi-max-frequency:
> +    maximum: 20000000
> +
> +  interrupts:
> +    maxItems: 3
> +
> +  interrupt-names:
> +    items:
> +      - const: irq0
> +      - const: irq1
> +      - const: dready
> +
> +  reset-gpios:
> +    description:
> +      Must be the device tree identifier of the RESET pin. As the line is
> +      active low, it should be marked GPIO_ACTIVE_LOW.
> +    maxItems: 1
> +
> +  vdd-supply: true
> +
> +  vref-supply: true
> +
> +  clocks:
> +    description: External clock source when not using crystal
> +    maxItems: 1
> +
> +  clock-names:
> +    items:
> +      - const: clkin
> +
> +  "#clock-cells":
> +    description:
> +      ADE9000 can provide clock output via CLKOUT pin with external buffer.
> +    const: 0
> +
> +  clock-output-names:
> +    items:
> +      - const: clkout

No point in having this if there is only 1 possible value. Unless you 
have some need, just drop this.

> +
> +required:
> +  - compatible
> +  - reg
> +  - reset-gpios
> +  - interrupts
> +  - interrupt-names
> +  - vdd-supply
> +
> +unevaluatedProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/gpio/gpio.h>
> +    #include <dt-bindings/interrupt-controller/irq.h>
> +
> +    spi {
> +      #address-cells = <1>;
> +      #size-cells = <0>;
> +
> +      adc@0 {
> +          compatible = "adi,ade9000";
> +          reg = <0>;
> +          spi-max-frequency = <7000000>;
> +
> +          #clock-cells = <0>;
> +          reset-gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
> +          interrupts = <2 IRQ_TYPE_EDGE_FALLING>, <3 IRQ_TYPE_EDGE_FALLING>, <4 IRQ_TYPE_EDGE_FALLING>;
> +          interrupt-names = "irq0", "irq1", "dready";
> +          interrupt-parent = <&gpio>;
> +          /* Optional: external clock instead of crystal */
> +          /* clocks = <&ext_clock_24576khz>; */
> +          /* clock-names = "clkin"; */
> +          clock-output-names = "clkout";
> +          vdd-supply = <&vdd_reg>;
> +      };
> +    };
> -- 
> 2.43.0
>