* [PATCH v5 0/2] media: i2c: Add OmniVision OV6211 image sensor driver
@ 2025-08-29 14:42 Vladimir Zapolskiy
2025-08-29 14:42 ` [PATCH v5 1/2] dt-bindings: media: i2c: Add OmniVision OV6211 image sensor Vladimir Zapolskiy
2025-08-29 14:42 ` [PATCH v5 2/2] media: i2c: Add OmniVision OV6211 image sensor driver Vladimir Zapolskiy
0 siblings, 2 replies; 3+ messages in thread
From: Vladimir Zapolskiy @ 2025-08-29 14:42 UTC (permalink / raw)
To: Mauro Carvalho Chehab, Hans Verkuil, Sakari Ailus, Tarang Raval
Cc: Rob Herring, Krzysztof Kozlowski, Conor Dooley, linux-media,
devicetree
OmniVision OV6211 is a monochrome image sensor, which produces frames in
8/10-bit raw output format and supports 400x400, 200x200 and 100x100
output image resolution modes.
At the moment the only supported resolution in the device driver is
400x400@120fps (Y8).
The driver version is based on top of media/master, which contains a new
devm_v4l2_sensor_clk_get() helper.
Output of v4l2-compliance tool from v4l-utils-1.20.0:
----8<----
v4l2-compliance SHA: not available, 64 bits, 64-bit time_t
Compliance test for device /dev/v4l-subdev28:
Required ioctls:
Allow for multiple opens:
test second /dev/v4l-subdev28 open: OK
test for unlimited opens: OK
test invalid ioctls: OK
Debug ioctls:
test VIDIOC_LOG_STATUS: OK (Not Supported)
Input ioctls:
test VIDIOC_G/S_TUNER/ENUM_FREQ_BANDS: OK (Not Supported)
test VIDIOC_G/S_FREQUENCY: OK (Not Supported)
test VIDIOC_S_HW_FREQ_SEEK: OK (Not Supported)
test VIDIOC_ENUMAUDIO: OK (Not Supported)
test VIDIOC_G/S/ENUMINPUT: OK (Not Supported)
test VIDIOC_G/S_AUDIO: OK (Not Supported)
Inputs: 0 Audio Inputs: 0 Tuners: 0
Output ioctls:
test VIDIOC_G/S_MODULATOR: OK (Not Supported)
test VIDIOC_G/S_FREQUENCY: OK (Not Supported)
test VIDIOC_ENUMAUDOUT: OK (Not Supported)
test VIDIOC_G/S/ENUMOUTPUT: OK (Not Supported)
test VIDIOC_G/S_AUDOUT: OK (Not Supported)
Outputs: 0 Audio Outputs: 0 Modulators: 0
Input/Output configuration ioctls:
test VIDIOC_ENUM/G/S/QUERY_STD: OK (Not Supported)
test VIDIOC_ENUM/G/S/QUERY_DV_TIMINGS: OK (Not Supported)
test VIDIOC_DV_TIMINGS_CAP: OK (Not Supported)
test VIDIOC_G/S_EDID: OK (Not Supported)
Control ioctls:
test VIDIOC_QUERY_EXT_CTRL/QUERYMENU: OK
test VIDIOC_QUERYCTRL: OK
test VIDIOC_G/S_CTRL: OK
test VIDIOC_G/S/TRY_EXT_CTRLS: OK
test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: OK
test VIDIOC_G/S_JPEGCOMP: OK (Not Supported)
Standard Controls: 10 Private Controls: 0
Format ioctls:
test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK (Not Supported)
test VIDIOC_G/S_PARM: OK (Not Supported)
test VIDIOC_G_FBUF: OK (Not Supported)
test VIDIOC_G_FMT: OK (Not Supported)
test VIDIOC_TRY_FMT: OK (Not Supported)
test VIDIOC_S_FMT: OK (Not Supported)
test VIDIOC_G_SLICED_VBI_CAP: OK (Not Supported)
test Cropping: OK (Not Supported)
test Composing: OK (Not Supported)
test Scaling: OK (Not Supported)
Codec ioctls:
test VIDIOC_(TRY_)ENCODER_CMD: OK (Not Supported)
test VIDIOC_G_ENC_INDEX: OK (Not Supported)
test VIDIOC_(TRY_)DECODER_CMD: OK (Not Supported)
Buffer ioctls:
test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK (Not Supported)
test VIDIOC_EXPBUF: OK (Not Supported)
test Requests: OK (Not Supported)
Total for device /dev/v4l-subdev28: 41, Succeeded: 41, Failed: 0, Warnings: 0
----8<----
Link to v4 of the OV6211 camera sensor device driver:
- https://lore.kernel.org/all/20250820224541.130229-1-vladimir.zapolskiy@linaro.org/
Changes from v4 to v5:
* removed unnecessary explicit setting of ov6211->sd.dev (Tarang),
* switched to regulator bulk operations (Sakari, Krzysztof),
* minor non-function clean-ups.
Link to v3 of the OV6211 camera sensor device driver:
- https://lore.kernel.org/all/20250812213024.361267-1-vladimir.zapolskiy@linaro.org/
Changes from v3 to v4:
* v4l2_ctrl_handler_init() properly set error in handler, an early check
is not mandatory (Tarang, Sakari),
* removed pm_runtime_mark_last_busy() since it's called by
pm_runtime_put_autosuspend() (Tarang, Sakari),
* pm_runtime_get_if_in_use() replaced by pm_runtime_get_if_active() (Sakari),
* use v4l2_link_freq_to_bitmap() helper function to check a link frequency
map (Sakari),
* added a new test pattern control, apparently it's identical to ov7251 one.
Link to v2 of the OV6211 camera sensor device driver:
- https://lore.kernel.org/all/20250729231454.242748-1-vladimir.zapolskiy@linaro.org/
Changes from v2 to v3:
* added Reviewed-by: tag to the device tree binding (Rob),
* simplifed access to the associated struct device (Tarang),
* ov6211_get_format() replaced by v4l2_subdev_state_get_format() (Tarang),
* removed private .cur_mode, since just one mode is supported (Tarang),
* removed a custom serialization mutex (Tarang),
* set power on before registering the sensor in V4L2 (Tarang),
* v4l2_subdev_internal_ops: replaced .open with .init_state,
* updated signature of ov6211_update_pad_format() to generalize it and
to simplify adding more modes in future,
* replaced a custom .s_stream from v4l2_subdev_video_ops by .enable_streams
and .disable_streams callbacks in v4l2_subdev_pad_ops,
* add support of PM runtime autosuspend into the driver,
* taking into account a similarity of OV6211 PLL1 configuration to
the known OV7251 PLL1 correct the set MIPI link frequency value.
Link to v1 of the OV6211 camera sensor device driver:
- https://lore.kernel.org/linux-media/20250717124001.108486-1-vladimir.zapolskiy@linaro.org/
Changes from v1 to v2:
* restrict endpoint unevaluated properties (Krzysztof),
* changed dev_err() to dev_err_probe() whenever it's applicable (Krzysztof),
* removed in-driver I2C operations in favour of V4L2 CCI interface (Kieran),
* added hblank, vblank, pixel rate and rotation/orientation V4L2 to
the list of controls (Kieran, Dave),
* due to unselectable data lanes property removed data_lanes handling (Dave),
* replaced devm_clk_get_optional() with devm_v4l2_sensor_clk_get() (Dave, Mehdi),
* minor cosmetic updates (reported error messages, goto label names etc.).
Vladimir Zapolskiy (2):
dt-bindings: media: i2c: Add OmniVision OV6211 image sensor
media: i2c: Add OmniVision OV6211 image sensor driver
.../bindings/media/i2c/ovti,ov6211.yaml | 96 +++
MAINTAINERS | 8 +
drivers/media/i2c/Kconfig | 10 +
drivers/media/i2c/Makefile | 1 +
drivers/media/i2c/ov6211.c | 793 ++++++++++++++++++
5 files changed, 908 insertions(+)
create mode 100644 Documentation/devicetree/bindings/media/i2c/ovti,ov6211.yaml
create mode 100644 drivers/media/i2c/ov6211.c
--
2.49.0
^ permalink raw reply [flat|nested] 3+ messages in thread
* [PATCH v5 1/2] dt-bindings: media: i2c: Add OmniVision OV6211 image sensor
2025-08-29 14:42 [PATCH v5 0/2] media: i2c: Add OmniVision OV6211 image sensor driver Vladimir Zapolskiy
@ 2025-08-29 14:42 ` Vladimir Zapolskiy
2025-08-29 14:42 ` [PATCH v5 2/2] media: i2c: Add OmniVision OV6211 image sensor driver Vladimir Zapolskiy
1 sibling, 0 replies; 3+ messages in thread
From: Vladimir Zapolskiy @ 2025-08-29 14:42 UTC (permalink / raw)
To: Mauro Carvalho Chehab, Hans Verkuil, Sakari Ailus, Tarang Raval
Cc: Rob Herring, Krzysztof Kozlowski, Conor Dooley, linux-media,
devicetree
Add device tree bindings documentation for OmniVision OV6211 image
sensor.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
---
.../bindings/media/i2c/ovti,ov6211.yaml | 96 +++++++++++++++++++
1 file changed, 96 insertions(+)
create mode 100644 Documentation/devicetree/bindings/media/i2c/ovti,ov6211.yaml
diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov6211.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov6211.yaml
new file mode 100644
index 000000000000..5a857fa2f371
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov6211.yaml
@@ -0,0 +1,96 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/ovti,ov6211.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: OmniVision OV6211 Image Sensor
+
+description:
+ OmniVision OV6211 image sensor is a high performance monochrome image
+ sensor. The sensor is controlled over a serial camera control bus
+ protocol (SCCB), the widest supported output image frame size is 400x400
+ at 120 frames per second rate, data output format is 8/10-bit RAW
+ transferred over one-lane MIPI D-PHY interface.
+
+maintainers:
+ - Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
+
+allOf:
+ - $ref: /schemas/media/video-interface-devices.yaml#
+
+properties:
+ compatible:
+ const: ovti,ov6211
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ description: XVCLK supply clock, 6MHz to 27MHz frequency.
+ maxItems: 1
+
+ reset-gpios:
+ description: Active low GPIO connected to XSHUTDOWN pad of the sensor.
+ maxItems: 1
+
+ strobe-gpios:
+ description: Input GPIO connected to strobe pad of the sensor.
+ maxItems: 1
+
+ avdd-supply:
+ description: Analogue voltage supply, 2.6 to 3.0 volts.
+
+ dovdd-supply:
+ description: Digital I/O voltage supply, 1.8 volts.
+
+ dvdd-supply:
+ description: Digital core voltage supply.
+
+ port:
+ $ref: /schemas/graph.yaml#/$defs/port-base
+ additionalProperties: false
+
+ properties:
+ endpoint:
+ $ref: /schemas/media/video-interfaces.yaml#
+ unevaluatedProperties: false
+
+ required:
+ - link-frequencies
+
+required:
+ - compatible
+ - reg
+ - port
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ camera@60 {
+ compatible = "ovti,ov6211";
+ reg = <0x60>;
+ clocks = <&camera_clk 0>;
+ assigned-clocks = <&camera_clk 0>;
+ assigned-clock-rates = <24000000>;
+ reset-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
+ avdd-supply = <&vreg_2p8>;
+ dovdd-supply = <&vreg_1p8>;
+ dvdd-supply = <&vreg_1p2>;
+
+ port {
+ endpoint {
+ link-frequencies = /bits/ 64 <480000000>;
+ remote-endpoint = <&mipi_csi2_ep>;
+ };
+ };
+ };
+ };
+...
--
2.49.0
^ permalink raw reply related [flat|nested] 3+ messages in thread
* [PATCH v5 2/2] media: i2c: Add OmniVision OV6211 image sensor driver
2025-08-29 14:42 [PATCH v5 0/2] media: i2c: Add OmniVision OV6211 image sensor driver Vladimir Zapolskiy
2025-08-29 14:42 ` [PATCH v5 1/2] dt-bindings: media: i2c: Add OmniVision OV6211 image sensor Vladimir Zapolskiy
@ 2025-08-29 14:42 ` Vladimir Zapolskiy
1 sibling, 0 replies; 3+ messages in thread
From: Vladimir Zapolskiy @ 2025-08-29 14:42 UTC (permalink / raw)
To: Mauro Carvalho Chehab, Hans Verkuil, Sakari Ailus, Tarang Raval
Cc: Rob Herring, Krzysztof Kozlowski, Conor Dooley, linux-media,
devicetree
OmniVision OV6211 is a monochrome image sensor, which produces frames in
8/10-bit raw output format and supports 400x400, 200x200 and 100x100
output image resolution modes.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
---
MAINTAINERS | 8 +
drivers/media/i2c/Kconfig | 10 +
drivers/media/i2c/Makefile | 1 +
drivers/media/i2c/ov6211.c | 793 +++++++++++++++++++++++++++++++++++++
4 files changed, 812 insertions(+)
create mode 100644 drivers/media/i2c/ov6211.c
diff --git a/MAINTAINERS b/MAINTAINERS
index 41e9014db574..4ce47d4b27a8 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -18727,6 +18727,14 @@ S: Maintained
T: git git://linuxtv.org/media.git
F: drivers/media/i2c/ov5695.c
+OMNIVISION OV6211 SENSOR DRIVER
+M: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
+L: linux-media@vger.kernel.org
+S: Maintained
+T: git git://linuxtv.org/media_tree.git
+F: Documentation/devicetree/bindings/media/i2c/ovti,ov6211.yaml
+F: drivers/media/i2c/ov6211.c
+
OMNIVISION OV64A40 SENSOR DRIVER
M: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
L: linux-media@vger.kernel.org
diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig
index 4fd22e49d301..cf4a8dd7c797 100644
--- a/drivers/media/i2c/Kconfig
+++ b/drivers/media/i2c/Kconfig
@@ -552,6 +552,16 @@ config VIDEO_OV5695
To compile this driver as a module, choose M here: the
module will be called ov5695.
+config VIDEO_OV6211
+ tristate "OmniVision OV6211 sensor support"
+ select V4L2_CCI_I2C
+ help
+ This is a Video4Linux2 sensor driver for the OmniVision
+ OV6211 camera.
+
+ To compile this driver as a module, choose M here: the
+ module will be called ov6211.
+
config VIDEO_OV64A40
tristate "OmniVision OV64A40 sensor support"
select V4L2_CCI_I2C
diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile
index 63ef5abbebf3..b5b82bd8e621 100644
--- a/drivers/media/i2c/Makefile
+++ b/drivers/media/i2c/Makefile
@@ -104,6 +104,7 @@ obj-$(CONFIG_VIDEO_OV5670) += ov5670.o
obj-$(CONFIG_VIDEO_OV5675) += ov5675.o
obj-$(CONFIG_VIDEO_OV5693) += ov5693.o
obj-$(CONFIG_VIDEO_OV5695) += ov5695.o
+obj-$(CONFIG_VIDEO_OV6211) += ov6211.o
obj-$(CONFIG_VIDEO_OV64A40) += ov64a40.o
obj-$(CONFIG_VIDEO_OV6650) += ov6650.o
obj-$(CONFIG_VIDEO_OV7251) += ov7251.o
diff --git a/drivers/media/i2c/ov6211.c b/drivers/media/i2c/ov6211.c
new file mode 100644
index 000000000000..dfd64f6515b9
--- /dev/null
+++ b/drivers/media/i2c/ov6211.c
@@ -0,0 +1,793 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2024-2025 Linaro Ltd
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/pm_runtime.h>
+#include <linux/regulator/consumer.h>
+#include <linux/units.h>
+#include <media/v4l2-cci.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-fwnode.h>
+
+#define OV6211_LINK_FREQ_480MHZ (480 * HZ_PER_MHZ)
+#define OV6211_MCLK_FREQ_24MHZ (24 * HZ_PER_MHZ)
+
+#define OV6211_REG_CHIP_ID CCI_REG16(0x300a)
+#define OV6211_CHIP_ID 0x6710
+
+#define OV6211_REG_MODE_SELECT CCI_REG8(0x0100)
+#define OV6211_MODE_STANDBY 0x00
+#define OV6211_MODE_STREAMING BIT(0)
+
+#define OV6211_REG_SOFTWARE_RST CCI_REG8(0x0103)
+#define OV6211_SOFTWARE_RST BIT(0)
+
+/* Exposure controls from sensor */
+#define OV6211_REG_EXPOSURE CCI_REG24(0x3500)
+#define OV6211_EXPOSURE_MIN 1
+#define OV6211_EXPOSURE_MAX_MARGIN 4
+#define OV6211_EXPOSURE_STEP 1
+#define OV6211_EXPOSURE_DEFAULT 210
+
+/* Analogue gain controls from sensor */
+#define OV6211_REG_ANALOGUE_GAIN CCI_REG16(0x350a)
+#define OV6211_ANALOGUE_GAIN_MIN 1
+#define OV6211_ANALOGUE_GAIN_MAX 0x3ff
+#define OV6211_ANALOGUE_GAIN_STEP 1
+#define OV6211_ANALOGUE_GAIN_DEFAULT 160
+
+/* Test pattern */
+#define OV6211_REG_PRE_ISP CCI_REG8(0x5e00)
+#define OV6211_TEST_PATTERN_ENABLE BIT(7)
+
+#define to_ov6211(_sd) container_of(_sd, struct ov6211, sd)
+
+static const s64 ov6211_link_freq_menu[] = {
+ OV6211_LINK_FREQ_480MHZ,
+};
+
+struct ov6211_reg_list {
+ const struct cci_reg_sequence *regs;
+ unsigned int num_regs;
+};
+
+struct ov6211_mode {
+ u32 width; /* Frame width in pixels */
+ u32 height; /* Frame height in pixels */
+ u32 hts; /* Horizontal timing size */
+ u32 vts; /* Default vertical timing size */
+ u32 bpp; /* Bits per pixel */
+
+ const struct ov6211_reg_list reg_list; /* Sensor register setting */
+};
+
+static const char * const ov6211_test_pattern_menu[] = {
+ "Disabled",
+ "Vertical Colour Bars",
+};
+
+static const char * const ov6211_supply_names[] = {
+ "avdd", /* Analog power */
+ "dovdd", /* Digital I/O power */
+ "dvdd", /* Digital core power */
+};
+
+#define OV6211_NUM_SUPPLIES ARRAY_SIZE(ov6211_supply_names)
+
+struct ov6211 {
+ struct device *dev;
+ struct regmap *regmap;
+ struct clk *xvclk;
+ struct gpio_desc *reset_gpio;
+ struct regulator_bulk_data supplies[OV6211_NUM_SUPPLIES];
+
+ struct v4l2_subdev sd;
+ struct media_pad pad;
+
+ struct v4l2_ctrl_handler ctrl_handler;
+
+ /* Saved register values */
+ u64 pre_isp;
+};
+
+static const struct cci_reg_sequence ov6211_400x400_120fps_mode[] = {
+ { CCI_REG8(0x3005), 0x00 },
+ { CCI_REG8(0x3013), 0x12 },
+ { CCI_REG8(0x3014), 0x04 },
+ { CCI_REG8(0x3016), 0x10 },
+ { CCI_REG8(0x3017), 0x00 },
+ { CCI_REG8(0x3018), 0x00 },
+ { CCI_REG8(0x301a), 0x00 },
+ { CCI_REG8(0x301b), 0x00 },
+ { CCI_REG8(0x301c), 0x00 },
+ { CCI_REG8(0x3037), 0xf0 },
+ { CCI_REG8(0x3080), 0x01 },
+ { CCI_REG8(0x3081), 0x00 },
+ { CCI_REG8(0x3082), 0x01 },
+ { CCI_REG8(0x3098), 0x04 },
+ { CCI_REG8(0x3099), 0x28 },
+ { CCI_REG8(0x309a), 0x06 },
+ { CCI_REG8(0x309b), 0x04 },
+ { CCI_REG8(0x309c), 0x00 },
+ { CCI_REG8(0x309d), 0x00 },
+ { CCI_REG8(0x309e), 0x01 },
+ { CCI_REG8(0x309f), 0x00 },
+ { CCI_REG8(0x30b0), 0x08 },
+ { CCI_REG8(0x30b1), 0x02 },
+ { CCI_REG8(0x30b2), 0x00 },
+ { CCI_REG8(0x30b3), 0x28 },
+ { CCI_REG8(0x30b4), 0x02 },
+ { CCI_REG8(0x30b5), 0x00 },
+ { CCI_REG8(0x3106), 0xd9 },
+ { CCI_REG8(0x3503), 0x07 },
+ { CCI_REG8(0x3509), 0x10 },
+ { CCI_REG8(0x3600), 0xfc },
+ { CCI_REG8(0x3620), 0xb7 },
+ { CCI_REG8(0x3621), 0x05 },
+ { CCI_REG8(0x3626), 0x31 },
+ { CCI_REG8(0x3627), 0x40 },
+ { CCI_REG8(0x3632), 0xa3 },
+ { CCI_REG8(0x3633), 0x34 },
+ { CCI_REG8(0x3634), 0x40 },
+ { CCI_REG8(0x3636), 0x00 },
+ { CCI_REG8(0x3660), 0x80 },
+ { CCI_REG8(0x3662), 0x03 },
+ { CCI_REG8(0x3664), 0xf0 },
+ { CCI_REG8(0x366a), 0x10 },
+ { CCI_REG8(0x366b), 0x06 },
+ { CCI_REG8(0x3680), 0xf4 },
+ { CCI_REG8(0x3681), 0x50 },
+ { CCI_REG8(0x3682), 0x00 },
+ { CCI_REG8(0x3708), 0x20 },
+ { CCI_REG8(0x3709), 0x40 },
+ { CCI_REG8(0x370d), 0x03 },
+ { CCI_REG8(0x373b), 0x02 },
+ { CCI_REG8(0x373c), 0x08 },
+ { CCI_REG8(0x3742), 0x00 },
+ { CCI_REG8(0x3744), 0x16 },
+ { CCI_REG8(0x3745), 0x08 },
+ { CCI_REG8(0x3781), 0xfc },
+ { CCI_REG8(0x3788), 0x00 },
+ { CCI_REG8(0x3800), 0x00 },
+ { CCI_REG8(0x3801), 0x04 },
+ { CCI_REG8(0x3802), 0x00 },
+ { CCI_REG8(0x3803), 0x04 },
+ { CCI_REG8(0x3804), 0x01 },
+ { CCI_REG8(0x3805), 0x9b },
+ { CCI_REG8(0x3806), 0x01 },
+ { CCI_REG8(0x3807), 0x9b },
+ { CCI_REG8(0x3808), 0x01 }, /* output width */
+ { CCI_REG8(0x3809), 0x90 },
+ { CCI_REG8(0x380a), 0x01 }, /* output height */
+ { CCI_REG8(0x380b), 0x90 },
+ { CCI_REG8(0x380c), 0x05 }, /* horizontal timing size */
+ { CCI_REG8(0x380d), 0xf2 },
+ { CCI_REG8(0x380e), 0x01 }, /* vertical timing size */
+ { CCI_REG8(0x380f), 0xb6 },
+ { CCI_REG8(0x3810), 0x00 },
+ { CCI_REG8(0x3811), 0x04 },
+ { CCI_REG8(0x3812), 0x00 },
+ { CCI_REG8(0x3813), 0x04 },
+ { CCI_REG8(0x3814), 0x11 },
+ { CCI_REG8(0x3815), 0x11 },
+ { CCI_REG8(0x3820), 0x00 },
+ { CCI_REG8(0x3821), 0x00 },
+ { CCI_REG8(0x382b), 0xfa },
+ { CCI_REG8(0x382f), 0x04 },
+ { CCI_REG8(0x3832), 0x00 },
+ { CCI_REG8(0x3833), 0x05 },
+ { CCI_REG8(0x3834), 0x00 },
+ { CCI_REG8(0x3835), 0x05 },
+ { CCI_REG8(0x3882), 0x04 },
+ { CCI_REG8(0x3883), 0x00 },
+ { CCI_REG8(0x38a4), 0x10 },
+ { CCI_REG8(0x38a5), 0x00 },
+ { CCI_REG8(0x38b1), 0x03 },
+ { CCI_REG8(0x3b80), 0x00 },
+ { CCI_REG8(0x3b81), 0xff },
+ { CCI_REG8(0x3b82), 0x10 },
+ { CCI_REG8(0x3b83), 0x00 },
+ { CCI_REG8(0x3b84), 0x08 },
+ { CCI_REG8(0x3b85), 0x00 },
+ { CCI_REG8(0x3b86), 0x01 },
+ { CCI_REG8(0x3b87), 0x00 },
+ { CCI_REG8(0x3b88), 0x00 },
+ { CCI_REG8(0x3b89), 0x00 },
+ { CCI_REG8(0x3b8a), 0x00 },
+ { CCI_REG8(0x3b8b), 0x05 },
+ { CCI_REG8(0x3b8c), 0x00 },
+ { CCI_REG8(0x3b8d), 0x00 },
+ { CCI_REG8(0x3b8e), 0x01 },
+ { CCI_REG8(0x3b8f), 0xb2 },
+ { CCI_REG8(0x3b94), 0x05 },
+ { CCI_REG8(0x3b95), 0xf2 },
+ { CCI_REG8(0x3b96), 0xc0 },
+ { CCI_REG8(0x4004), 0x04 },
+ { CCI_REG8(0x404e), 0x01 },
+ { CCI_REG8(0x4801), 0x0f },
+ { CCI_REG8(0x4806), 0x0f },
+ { CCI_REG8(0x4837), 0x43 },
+ { CCI_REG8(0x5a08), 0x00 },
+ { CCI_REG8(0x5a01), 0x00 },
+ { CCI_REG8(0x5a03), 0x00 },
+ { CCI_REG8(0x5a04), 0x10 },
+ { CCI_REG8(0x5a05), 0xa0 },
+ { CCI_REG8(0x5a06), 0x0c },
+ { CCI_REG8(0x5a07), 0x78 },
+};
+
+static const struct ov6211_mode supported_modes[] = {
+ {
+ .width = 400,
+ .height = 400,
+ .hts = 1522,
+ .vts = 438,
+ .bpp = 8,
+ .reg_list = {
+ .regs = ov6211_400x400_120fps_mode,
+ .num_regs = ARRAY_SIZE(ov6211_400x400_120fps_mode),
+ },
+ },
+};
+
+static int ov6211_set_test_pattern(struct ov6211 *ov6211, u32 pattern)
+{
+ u64 val = ov6211->pre_isp;
+
+ if (pattern)
+ val |= OV6211_TEST_PATTERN_ENABLE;
+ else
+ val &= ~OV6211_TEST_PATTERN_ENABLE;
+
+ return cci_write(ov6211->regmap, OV6211_REG_PRE_ISP, val, NULL);
+}
+
+static int ov6211_set_ctrl(struct v4l2_ctrl *ctrl)
+{
+ struct ov6211 *ov6211 = container_of(ctrl->handler, struct ov6211,
+ ctrl_handler);
+ int ret;
+
+ /* V4L2 controls are applied, when sensor is powered up for streaming */
+ if (!pm_runtime_get_if_active(ov6211->dev))
+ return 0;
+
+ switch (ctrl->id) {
+ case V4L2_CID_ANALOGUE_GAIN:
+ ret = cci_write(ov6211->regmap, OV6211_REG_ANALOGUE_GAIN,
+ ctrl->val, NULL);
+ break;
+ case V4L2_CID_EXPOSURE:
+ ret = cci_write(ov6211->regmap, OV6211_REG_EXPOSURE,
+ ctrl->val << 4, NULL);
+ break;
+ case V4L2_CID_TEST_PATTERN:
+ ret = ov6211_set_test_pattern(ov6211, ctrl->val);
+ break;
+ default:
+ ret = -EINVAL;
+ break;
+ }
+
+ pm_runtime_put(ov6211->dev);
+
+ return ret;
+}
+
+static const struct v4l2_ctrl_ops ov6211_ctrl_ops = {
+ .s_ctrl = ov6211_set_ctrl,
+};
+
+static int ov6211_init_controls(struct ov6211 *ov6211)
+{
+ struct v4l2_ctrl_handler *ctrl_hdlr = &ov6211->ctrl_handler;
+ const struct ov6211_mode *mode = &supported_modes[0];
+ struct v4l2_fwnode_device_properties props;
+ s64 exposure_max, pixel_rate, h_blank;
+ struct v4l2_ctrl *ctrl;
+ int ret;
+
+ v4l2_ctrl_handler_init(ctrl_hdlr, 9);
+
+ ctrl = v4l2_ctrl_new_int_menu(ctrl_hdlr, &ov6211_ctrl_ops,
+ V4L2_CID_LINK_FREQ,
+ ARRAY_SIZE(ov6211_link_freq_menu) - 1,
+ 0, ov6211_link_freq_menu);
+ if (ctrl)
+ ctrl->flags |= V4L2_CTRL_FLAG_READ_ONLY;
+
+ pixel_rate = ov6211_link_freq_menu[0] / mode->bpp;
+ v4l2_ctrl_new_std(ctrl_hdlr, &ov6211_ctrl_ops, V4L2_CID_PIXEL_RATE,
+ 0, pixel_rate, 1, pixel_rate);
+
+ h_blank = mode->hts - mode->width;
+ ctrl = v4l2_ctrl_new_std(ctrl_hdlr, &ov6211_ctrl_ops, V4L2_CID_HBLANK,
+ h_blank, h_blank, 1, h_blank);
+ if (ctrl)
+ ctrl->flags |= V4L2_CTRL_FLAG_READ_ONLY;
+
+ ctrl = v4l2_ctrl_new_std(ctrl_hdlr, &ov6211_ctrl_ops, V4L2_CID_VBLANK,
+ mode->vts - mode->height,
+ mode->vts - mode->height, 1,
+ mode->vts - mode->height);
+ if (ctrl)
+ ctrl->flags |= V4L2_CTRL_FLAG_READ_ONLY;
+
+ v4l2_ctrl_new_std(ctrl_hdlr, &ov6211_ctrl_ops, V4L2_CID_ANALOGUE_GAIN,
+ OV6211_ANALOGUE_GAIN_MIN, OV6211_ANALOGUE_GAIN_MAX,
+ OV6211_ANALOGUE_GAIN_STEP,
+ OV6211_ANALOGUE_GAIN_DEFAULT);
+
+ exposure_max = (mode->vts - OV6211_EXPOSURE_MAX_MARGIN);
+ v4l2_ctrl_new_std(ctrl_hdlr, &ov6211_ctrl_ops,
+ V4L2_CID_EXPOSURE,
+ OV6211_EXPOSURE_MIN, exposure_max,
+ OV6211_EXPOSURE_STEP,
+ OV6211_EXPOSURE_DEFAULT);
+
+ v4l2_ctrl_new_std_menu_items(ctrl_hdlr, &ov6211_ctrl_ops,
+ V4L2_CID_TEST_PATTERN,
+ ARRAY_SIZE(ov6211_test_pattern_menu) - 1,
+ 0, 0, ov6211_test_pattern_menu);
+
+ if (ctrl_hdlr->error)
+ return ctrl_hdlr->error;
+
+ ret = v4l2_fwnode_device_parse(ov6211->dev, &props);
+ if (ret)
+ goto error_free_hdlr;
+
+ ret = v4l2_ctrl_new_fwnode_properties(ctrl_hdlr, &ov6211_ctrl_ops,
+ &props);
+ if (ret)
+ goto error_free_hdlr;
+
+ ov6211->sd.ctrl_handler = ctrl_hdlr;
+
+ return 0;
+
+error_free_hdlr:
+ v4l2_ctrl_handler_free(ctrl_hdlr);
+
+ return ret;
+}
+
+static void ov6211_update_pad_format(const struct ov6211_mode *mode,
+ struct v4l2_mbus_framefmt *fmt)
+{
+ fmt->code = MEDIA_BUS_FMT_Y8_1X8;
+ fmt->width = mode->width;
+ fmt->height = mode->height;
+ fmt->field = V4L2_FIELD_NONE;
+ fmt->colorspace = V4L2_COLORSPACE_RAW;
+ fmt->ycbcr_enc = V4L2_YCBCR_ENC_DEFAULT;
+ fmt->quantization = V4L2_QUANTIZATION_FULL_RANGE;
+ fmt->xfer_func = V4L2_XFER_FUNC_NONE;
+}
+
+static int ov6211_enable_streams(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *state, u32 pad,
+ u64 streams_mask)
+{
+ const struct ov6211_reg_list *reg_list = &supported_modes[0].reg_list;
+ struct ov6211 *ov6211 = to_ov6211(sd);
+ int ret;
+
+ ret = pm_runtime_resume_and_get(ov6211->dev);
+ if (ret)
+ return ret;
+
+ /* Skip a step of explicit entering into the standby mode */
+ ret = cci_write(ov6211->regmap, OV6211_REG_SOFTWARE_RST,
+ OV6211_SOFTWARE_RST, NULL);
+ if (ret) {
+ dev_err(ov6211->dev, "failed to software reset: %d\n", ret);
+ goto error;
+ }
+
+ ret = cci_multi_reg_write(ov6211->regmap, reg_list->regs,
+ reg_list->num_regs, NULL);
+ if (ret) {
+ dev_err(ov6211->dev, "failed to set mode: %d\n", ret);
+ goto error;
+ }
+
+ ret = __v4l2_ctrl_handler_setup(ov6211->sd.ctrl_handler);
+ if (ret)
+ goto error;
+
+ ret = cci_write(ov6211->regmap, OV6211_REG_MODE_SELECT,
+ OV6211_MODE_STREAMING, NULL);
+ if (ret) {
+ dev_err(ov6211->dev, "failed to start streaming: %d\n", ret);
+ goto error;
+ }
+
+ return 0;
+
+error:
+ pm_runtime_put_autosuspend(ov6211->dev);
+
+ return ret;
+}
+
+static int ov6211_disable_streams(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *state, u32 pad,
+ u64 streams_mask)
+{
+ struct ov6211 *ov6211 = to_ov6211(sd);
+ int ret;
+
+ ret = cci_write(ov6211->regmap, OV6211_REG_MODE_SELECT,
+ OV6211_MODE_STANDBY, NULL);
+ if (ret)
+ dev_err(ov6211->dev, "failed to stop streaming: %d\n", ret);
+
+ pm_runtime_put_autosuspend(ov6211->dev);
+
+ return ret;
+}
+
+static int ov6211_set_pad_format(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *state,
+ struct v4l2_subdev_format *fmt)
+{
+ struct v4l2_mbus_framefmt *format;
+ const struct ov6211_mode *mode;
+
+ format = v4l2_subdev_state_get_format(state, 0);
+
+ mode = v4l2_find_nearest_size(supported_modes,
+ ARRAY_SIZE(supported_modes),
+ width, height,
+ fmt->format.width,
+ fmt->format.height);
+
+ ov6211_update_pad_format(mode, &fmt->format);
+ *format = fmt->format;
+
+ return 0;
+}
+
+static int ov6211_enum_mbus_code(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *sd_state,
+ struct v4l2_subdev_mbus_code_enum *code)
+{
+ if (code->index > 0)
+ return -EINVAL;
+
+ code->code = MEDIA_BUS_FMT_Y8_1X8;
+
+ return 0;
+}
+
+static int ov6211_enum_frame_size(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *sd_state,
+ struct v4l2_subdev_frame_size_enum *fse)
+{
+ if (fse->index >= ARRAY_SIZE(supported_modes))
+ return -EINVAL;
+
+ if (fse->code != MEDIA_BUS_FMT_Y8_1X8)
+ return -EINVAL;
+
+ fse->min_width = supported_modes[fse->index].width;
+ fse->max_width = fse->min_width;
+ fse->min_height = supported_modes[fse->index].height;
+ fse->max_height = fse->min_height;
+
+ return 0;
+}
+
+static int ov6211_init_state(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *state)
+{
+ struct v4l2_subdev_format fmt = {
+ .which = V4L2_SUBDEV_FORMAT_TRY,
+ .pad = 0,
+ .format = {
+ .code = MEDIA_BUS_FMT_Y8_1X8,
+ .width = supported_modes[0].width,
+ .height = supported_modes[0].height,
+ },
+ };
+
+ ov6211_set_pad_format(sd, state, &fmt);
+
+ return 0;
+}
+
+static const struct v4l2_subdev_video_ops ov6211_video_ops = {
+ .s_stream = v4l2_subdev_s_stream_helper,
+};
+
+static const struct v4l2_subdev_pad_ops ov6211_pad_ops = {
+ .set_fmt = ov6211_set_pad_format,
+ .get_fmt = v4l2_subdev_get_fmt,
+ .enum_mbus_code = ov6211_enum_mbus_code,
+ .enum_frame_size = ov6211_enum_frame_size,
+ .enable_streams = ov6211_enable_streams,
+ .disable_streams = ov6211_disable_streams,
+};
+
+static const struct v4l2_subdev_ops ov6211_subdev_ops = {
+ .video = &ov6211_video_ops,
+ .pad = &ov6211_pad_ops,
+};
+
+static const struct v4l2_subdev_internal_ops ov6211_internal_ops = {
+ .init_state = ov6211_init_state,
+};
+
+static const struct media_entity_operations ov6211_subdev_entity_ops = {
+ .link_validate = v4l2_subdev_link_validate,
+};
+
+static int ov6211_identify_sensor(struct ov6211 *ov6211)
+{
+ u64 val;
+ int ret;
+
+ ret = cci_read(ov6211->regmap, OV6211_REG_CHIP_ID, &val, NULL);
+ if (ret) {
+ dev_err(ov6211->dev, "failed to read chip id: %d\n", ret);
+ return ret;
+ }
+
+ if (val != OV6211_CHIP_ID) {
+ dev_err(ov6211->dev, "chip id mismatch: %x!=%llx\n",
+ OV6211_CHIP_ID, val);
+ return -ENODEV;
+ }
+
+ ret = cci_read(ov6211->regmap, OV6211_REG_PRE_ISP,
+ &ov6211->pre_isp, NULL);
+ if (ret)
+ dev_err(ov6211->dev, "failed to read pre_isp: %d\n", ret);
+
+ return ret;
+}
+
+static int ov6211_check_hwcfg(struct ov6211 *ov6211)
+{
+ struct fwnode_handle *fwnode = dev_fwnode(ov6211->dev), *ep;
+ struct v4l2_fwnode_endpoint bus_cfg = {
+ .bus_type = V4L2_MBUS_CSI2_DPHY,
+ };
+ unsigned long freq_bitmap;
+ int ret;
+
+ if (!fwnode)
+ return -ENODEV;
+
+ ep = fwnode_graph_get_next_endpoint(fwnode, NULL);
+ if (!ep)
+ return -EINVAL;
+
+ ret = v4l2_fwnode_endpoint_alloc_parse(ep, &bus_cfg);
+ fwnode_handle_put(ep);
+ if (ret)
+ return ret;
+
+ ret = v4l2_link_freq_to_bitmap(ov6211->dev, bus_cfg.link_frequencies,
+ bus_cfg.nr_of_link_frequencies,
+ ov6211_link_freq_menu,
+ ARRAY_SIZE(ov6211_link_freq_menu),
+ &freq_bitmap);
+
+ v4l2_fwnode_endpoint_free(&bus_cfg);
+
+ return ret;
+}
+
+static int ov6211_power_on(struct device *dev)
+{
+ struct v4l2_subdev *sd = dev_get_drvdata(dev);
+ struct ov6211 *ov6211 = to_ov6211(sd);
+ int ret;
+
+ ret = regulator_bulk_enable(OV6211_NUM_SUPPLIES, ov6211->supplies);
+ if (ret)
+ return ret;
+
+ gpiod_set_value_cansleep(ov6211->reset_gpio, 0);
+ usleep_range(10 * USEC_PER_MSEC, 15 * USEC_PER_MSEC);
+
+ ret = clk_prepare_enable(ov6211->xvclk);
+ if (ret)
+ goto reset_gpio;
+
+ return 0;
+
+reset_gpio:
+ gpiod_set_value_cansleep(ov6211->reset_gpio, 1);
+
+ regulator_bulk_disable(OV6211_NUM_SUPPLIES, ov6211->supplies);
+
+ return ret;
+}
+
+static int ov6211_power_off(struct device *dev)
+{
+ struct v4l2_subdev *sd = dev_get_drvdata(dev);
+ struct ov6211 *ov6211 = to_ov6211(sd);
+
+ clk_disable_unprepare(ov6211->xvclk);
+
+ gpiod_set_value_cansleep(ov6211->reset_gpio, 1);
+
+ regulator_bulk_disable(OV6211_NUM_SUPPLIES, ov6211->supplies);
+
+ return 0;
+}
+
+static int ov6211_probe(struct i2c_client *client)
+{
+ struct ov6211 *ov6211;
+ unsigned long freq;
+ unsigned int i;
+ int ret;
+
+ ov6211 = devm_kzalloc(&client->dev, sizeof(*ov6211), GFP_KERNEL);
+ if (!ov6211)
+ return -ENOMEM;
+
+ ov6211->dev = &client->dev;
+
+ v4l2_i2c_subdev_init(&ov6211->sd, client, &ov6211_subdev_ops);
+
+ ov6211->regmap = devm_cci_regmap_init_i2c(client, 16);
+ if (IS_ERR(ov6211->regmap))
+ return dev_err_probe(ov6211->dev, PTR_ERR(ov6211->regmap),
+ "failed to init CCI\n");
+
+ ov6211->xvclk = devm_v4l2_sensor_clk_get(ov6211->dev, NULL);
+ if (IS_ERR(ov6211->xvclk))
+ return dev_err_probe(ov6211->dev, PTR_ERR(ov6211->xvclk),
+ "failed to get XVCLK clock\n");
+
+ freq = clk_get_rate(ov6211->xvclk);
+ if (freq && freq != OV6211_MCLK_FREQ_24MHZ)
+ return dev_err_probe(ov6211->dev, -EINVAL,
+ "XVCLK clock frequency %lu is not supported\n",
+ freq);
+
+ ret = ov6211_check_hwcfg(ov6211);
+ if (ret)
+ return dev_err_probe(ov6211->dev, ret,
+ "failed to check HW configuration\n");
+
+ ov6211->reset_gpio = devm_gpiod_get_optional(ov6211->dev, "reset",
+ GPIOD_OUT_HIGH);
+ if (IS_ERR(ov6211->reset_gpio))
+ return dev_err_probe(ov6211->dev, PTR_ERR(ov6211->reset_gpio),
+ "cannot get reset GPIO\n");
+
+ for (i = 0; i < OV6211_NUM_SUPPLIES; i++)
+ ov6211->supplies[i].supply = ov6211_supply_names[i];
+
+ ret = devm_regulator_bulk_get(ov6211->dev, OV6211_NUM_SUPPLIES,
+ ov6211->supplies);
+ if (ret)
+ return dev_err_probe(ov6211->dev, ret,
+ "failed to get supply regulators\n");
+
+ /* The sensor must be powered on to read the CHIP_ID register */
+ ret = ov6211_power_on(ov6211->dev);
+ if (ret)
+ return ret;
+
+ ret = ov6211_identify_sensor(ov6211);
+ if (ret) {
+ dev_err_probe(ov6211->dev, ret, "failed to find sensor\n");
+ goto power_off;
+ }
+
+ ret = ov6211_init_controls(ov6211);
+ if (ret) {
+ dev_err_probe(ov6211->dev, ret, "failed to init controls\n");
+ goto power_off;
+ }
+
+ ov6211->sd.state_lock = ov6211->ctrl_handler.lock;
+ ov6211->sd.internal_ops = &ov6211_internal_ops;
+ ov6211->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
+ ov6211->sd.entity.ops = &ov6211_subdev_entity_ops;
+ ov6211->sd.entity.function = MEDIA_ENT_F_CAM_SENSOR;
+ ov6211->pad.flags = MEDIA_PAD_FL_SOURCE;
+
+ ret = media_entity_pads_init(&ov6211->sd.entity, 1, &ov6211->pad);
+ if (ret) {
+ dev_err_probe(ov6211->dev, ret,
+ "failed to init media entity pads\n");
+ goto v4l2_ctrl_handler_free;
+ }
+
+ ret = v4l2_subdev_init_finalize(&ov6211->sd);
+ if (ret < 0) {
+ dev_err_probe(ov6211->dev, ret,
+ "failed to init media entity pads\n");
+ goto media_entity_cleanup;
+ }
+
+ pm_runtime_set_active(ov6211->dev);
+ pm_runtime_enable(ov6211->dev);
+
+ ret = v4l2_async_register_subdev_sensor(&ov6211->sd);
+ if (ret < 0) {
+ dev_err_probe(ov6211->dev, ret,
+ "failed to register V4L2 subdev\n");
+ goto subdev_cleanup;
+ }
+
+ /* Enable runtime PM and turn off the device */
+ pm_runtime_idle(ov6211->dev);
+ pm_runtime_set_autosuspend_delay(ov6211->dev, 1000);
+ pm_runtime_use_autosuspend(ov6211->dev);
+
+ return 0;
+
+subdev_cleanup:
+ v4l2_subdev_cleanup(&ov6211->sd);
+ pm_runtime_disable(ov6211->dev);
+ pm_runtime_set_suspended(ov6211->dev);
+
+media_entity_cleanup:
+ media_entity_cleanup(&ov6211->sd.entity);
+
+v4l2_ctrl_handler_free:
+ v4l2_ctrl_handler_free(ov6211->sd.ctrl_handler);
+
+power_off:
+ ov6211_power_off(ov6211->dev);
+
+ return ret;
+}
+
+static void ov6211_remove(struct i2c_client *client)
+{
+ struct v4l2_subdev *sd = i2c_get_clientdata(client);
+ struct ov6211 *ov6211 = to_ov6211(sd);
+
+ v4l2_async_unregister_subdev(sd);
+ v4l2_subdev_cleanup(sd);
+ media_entity_cleanup(&sd->entity);
+ v4l2_ctrl_handler_free(sd->ctrl_handler);
+ pm_runtime_disable(ov6211->dev);
+
+ if (!pm_runtime_status_suspended(ov6211->dev)) {
+ ov6211_power_off(ov6211->dev);
+ pm_runtime_set_suspended(ov6211->dev);
+ }
+}
+
+static const struct dev_pm_ops ov6211_pm_ops = {
+ SET_RUNTIME_PM_OPS(ov6211_power_off, ov6211_power_on, NULL)
+};
+
+static const struct of_device_id ov6211_of_match[] = {
+ { .compatible = "ovti,ov6211" },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, ov6211_of_match);
+
+static struct i2c_driver ov6211_i2c_driver = {
+ .driver = {
+ .name = "ov6211",
+ .pm = &ov6211_pm_ops,
+ .of_match_table = ov6211_of_match,
+ },
+ .probe = ov6211_probe,
+ .remove = ov6211_remove,
+};
+
+module_i2c_driver(ov6211_i2c_driver);
+
+MODULE_AUTHOR("Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>");
+MODULE_DESCRIPTION("OmniVision OV6211 sensor driver");
+MODULE_LICENSE("GPL");
--
2.49.0
^ permalink raw reply related [flat|nested] 3+ messages in thread
end of thread, other threads:[~2025-08-29 14:42 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2025-08-29 14:42 [PATCH v5 0/2] media: i2c: Add OmniVision OV6211 image sensor driver Vladimir Zapolskiy
2025-08-29 14:42 ` [PATCH v5 1/2] dt-bindings: media: i2c: Add OmniVision OV6211 image sensor Vladimir Zapolskiy
2025-08-29 14:42 ` [PATCH v5 2/2] media: i2c: Add OmniVision OV6211 image sensor driver Vladimir Zapolskiy
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).