[PATCH 1/2] dt-bindings: iio: afe: current-sense-amplifier: Add io-channel-cells

[PATCH 1/2] dt-bindings: iio: afe: current-sense-amplifier: Add io-channel-cells

[Primoz Fiser]

The current-sense-amplifier is an IIO provider thus can be referenced by
IIO consumers (via "io-channels" property in consumer device node). Such
provider is required to describe number of cells used in phandle lookup
with "io-channel-cells" property, otherwise the following kernel error
is present:

  OF: /iio-hwmon: could not get #io-channel-cells for /current-sense

Also fixes the following dtbs_check warning:

  current-sense: '#io-channel-cells' does not match any of the regexes:
  'pinctrl-[0-9]+' from schema $id:
  http://devicetree.org/schemas/iio/afe/current-sense-amplifier.yaml#

Fixes: fbac26b9ad21 ("dt-bindings:iio:afe:current-sense-amplifier: txt to yaml conversion.")
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
---
 .../devicetree/bindings/iio/afe/current-sense-amplifier.yaml  | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/Documentation/devicetree/bindings/iio/afe/current-sense-amplifier.yaml b/Documentation/devicetree/bindings/iio/afe/current-sense-amplifier.yaml
index 527501c1d695..bcf4ddcfd13b 100644
--- a/Documentation/devicetree/bindings/iio/afe/current-sense-amplifier.yaml
+++ b/Documentation/devicetree/bindings/iio/afe/current-sense-amplifier.yaml
@@ -24,6 +24,9 @@ properties:
     description: |
       Channel node of a voltage io-channel.
 
+  "#io-channel-cells":
+    const: 0
+
   sense-resistor-micro-ohms:
     description: The sense resistance.
 
@@ -46,6 +49,7 @@ examples:
   - |
     sysi {
         compatible = "current-sense-amplifier";
+        #io-channel-cells = <0>;
         io-channels = <&tiadc 0>;
 
         sense-resistor-micro-ohms = <20000>;
-- 
2.34.1

[PATCH 2/2] arm64: dts: freescale: imx93-phyboard-nash: Current sense via iio-hwmon

[Primoz Fiser]

Commit 21179eae56de ("arm64: dts: freescale: imx93-phyboard-nash: Add
current sense amplifier") added information about the current sensing
circuitry found on the board. Now, lets provide current sense reading
also via IIO-hwmon subsystem. This way, SoM current can be read directly
via sysfs property more conveniently for the customers. No need for them
to manually apply scaling factor calculations anymore.

Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
---
 arch/arm64/boot/dts/freescale/imx93-phyboard-nash.dts | 8 +++++++-
 1 file changed, 7 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/freescale/imx93-phyboard-nash.dts b/arch/arm64/boot/dts/freescale/imx93-phyboard-nash.dts
index 71a0e9f270af..d05645f25bba 100644
--- a/arch/arm64/boot/dts/freescale/imx93-phyboard-nash.dts
+++ b/arch/arm64/boot/dts/freescale/imx93-phyboard-nash.dts
@@ -27,8 +27,9 @@ chosen {
 		stdout-path = &lpuart1;
 	};
 
-	current-sense {
+	curr_sens: current-sense {
 		compatible = "current-sense-amplifier";
+		#io-channel-cells = <0>;
 		io-channels = <&adc1 1>;
 		sense-gain-div = <2>;
 		sense-gain-mult = <50>;
@@ -44,6 +45,11 @@ flexcan1_tc: can-phy0 {
 		standby-gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
 	};
 
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&curr_sens 0>;
+	};
+
 	reg_usdhc2_vmmc: regulator-usdhc2 {
 		compatible = "regulator-fixed";
 		gpio = <&gpio3 7 GPIO_ACTIVE_HIGH>;
-- 
2.34.1