[PATCH v3 0/3] arm64: dts: nuvoton: add NPCM845 SoC and EVB support

[PATCH v3 0/3] arm64: dts: nuvoton: add NPCM845 SoC and EVB support

[Tomer Maimon]

This series fix warnings and adds device tree support for peripherals on 
the Nuvoton NPCM845 SoC and its Evaluation Board (EVB).
The first patch fix warning and arrange node order.
The second patch introduces peripheral nodes for Ethernet, MMC, SPI, USB,
RNG, ADC, PWM-FAN, I2C, and OP-TEE firmware in the NPCM845 SoC device tree.
The third patch enables these peripherals for the NPCM845-EVB, adding
MDIO nodes, reserved memory, aliases, and board-specific configurations
like PHY modes and SPI flash partitions.

The NPCM8XX device tree tested on NPCM845 evaluation board.

Addressed comments from:
	- Andrew Jeffery: https://patchwork.ozlabs.org/project/openbmc/patch/20250908125938.3584927-2-tmaimon77@gmail.com/
					  https://patchwork.ozlabs.org/project/openbmc/patch/20250908125938.3584927-3-tmaimon77@gmail.com/

Changes since version 2:
	- Fix dts warning
	- Arrange node order by ascending unit address.

Changes since version 1:
	- Fix commit message
	- Fix dtbs_check warnings.

Tomer Maimon (3):
  arm64: dts: nuvoton: fix warning and nodes order
  arm64: dts: nuvoton: npcm845: Add peripheral nodes
  arm64: dts: nuvoton: npcm845-evb: Add peripheral nodes

 .../dts/nuvoton/nuvoton-common-npcm8xx.dtsi   | 732 +++++++++++++++++-
 .../boot/dts/nuvoton/nuvoton-npcm845-evb.dts  | 440 +++++++++++
 .../boot/dts/nuvoton/nuvoton-npcm845.dtsi     |   7 +
 3 files changed, 1160 insertions(+), 19 deletions(-)

-- 
2.34.1

[PATCH v3 1/3] arm64: dts: nuvoton: fix warning and nodes order

[Tomer Maimon]

Fix the warning in the gcr and timer nodes, and modify nodes order by
ascending unit address.

Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
---
 .../dts/nuvoton/nuvoton-common-npcm8xx.dtsi   | 35 +++++++++----------
 1 file changed, 17 insertions(+), 18 deletions(-)

diff --git a/arch/arm64/boot/dts/nuvoton/nuvoton-common-npcm8xx.dtsi b/arch/arm64/boot/dts/nuvoton/nuvoton-common-npcm8xx.dtsi
index 24133528b8e9..a43514f624c0 100644
--- a/arch/arm64/boot/dts/nuvoton/nuvoton-common-npcm8xx.dtsi
+++ b/arch/arm64/boot/dts/nuvoton/nuvoton-common-npcm8xx.dtsi
@@ -18,7 +18,7 @@ soc {
 		ranges;
 
 		gcr: system-controller@f0800000 {
-			compatible = "nuvoton,npcm845-gcr", "syscon";
+			compatible = "nuvoton,npcm845-gcr", "syscon", "simple-mfd";
 			reg = <0x0 0xf0800000 0x0 0x1000>;
 		};
 
@@ -59,23 +59,6 @@ apb {
 			ranges = <0x0 0x0 0xf0000000 0x00300000>,
 				<0xfff00000 0x0 0xfff00000 0x00016000>;
 
-			peci: peci-controller@100000 {
-				compatible = "nuvoton,npcm845-peci";
-				reg = <0x100000 0x1000>;
-				interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&clk NPCM8XX_CLK_APB3>;
-				cmd-timeout-ms = <1000>;
-				status = "disabled";
-			};
-
-			timer0: timer@8000 {
-				compatible = "nuvoton,npcm845-timer";
-				interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0x8000 0x1C>;
-				clocks = <&refclk>;
-				clock-names = "refclk";
-			};
-
 			serial0: serial@0 {
 				compatible = "nuvoton,npcm845-uart", "nuvoton,npcm750-uart";
 				reg = <0x0 0x1000>;
@@ -139,6 +122,13 @@ serial6: serial@6000 {
 				status = "disabled";
 			};
 
+			timer0: timer@8000 {
+				compatible = "nuvoton,npcm845-timer";
+				interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x8000 0x1C>;
+				clocks = <&refclk>;
+			};
+
 			watchdog0: watchdog@801c {
 				compatible = "nuvoton,npcm845-wdt", "nuvoton,npcm750-wdt";
 				interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
@@ -165,6 +155,15 @@ watchdog2: watchdog@a01c {
 				clocks = <&refclk>;
 				syscon = <&gcr>;
 			};
+
+			peci: peci-controller@100000 {
+				compatible = "nuvoton,npcm845-peci";
+				reg = <0x100000 0x1000>;
+				interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk NPCM8XX_CLK_APB3>;
+				cmd-timeout-ms = <1000>;
+				status = "disabled";
+			};
 		};
 	};
 
-- 
2.34.1

[PATCH v3 2/3] arm64: dts: nuvoton: npcm845: Add peripheral nodes

[Tomer Maimon]

Enable peripheral support for the Nuvoton NPCM845 SoC by adding device
nodes for Ethernet controllers, MMC controller, SPI controllers, USB
device controllers, random number generator, ADC, PWM-FAN controller,
and I2C controllers. Include pinmux configurations for relevant
peripherals to support hardware operation. Add an OP-TEE firmware node
for secure services.

Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
---
 .../dts/nuvoton/nuvoton-common-npcm8xx.dtsi   | 697 +++++++++++++++++-
 .../boot/dts/nuvoton/nuvoton-npcm845.dtsi     |   7 +
 2 files changed, 703 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/nuvoton/nuvoton-common-npcm8xx.dtsi b/arch/arm64/boot/dts/nuvoton/nuvoton-common-npcm8xx.dtsi
index a43514f624c0..485705c68e04 100644
--- a/arch/arm64/boot/dts/nuvoton/nuvoton-common-npcm8xx.dtsi
+++ b/arch/arm64/boot/dts/nuvoton/nuvoton-common-npcm8xx.dtsi
@@ -4,6 +4,7 @@
 #include <dt-bindings/clock/nuvoton,npcm845-clk.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	#address-cells = <2>;
@@ -35,6 +36,11 @@ gic: interrupt-controller@dfff9000 {
 		};
 	};
 
+	udc0_phy: usb-phy {
+		compatible = "usb-nop-xceiv";
+		#phy-cells = <0>;
+	};
+
 	ahb {
 		#address-cells = <2>;
 		#size-cells = <2>;
@@ -51,7 +57,260 @@ clk: rstc: reset-controller@f0801000 {
 			#clock-cells = <1>;
 		};
 
-		apb {
+		gmac1: ethernet@f0804000 {
+			device_type = "network";
+			compatible = "snps,dwmac-3.72a", "snps,dwmac";
+			reg = <0x0 0xf0804000 0x0 0x2000>;
+			interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq";
+			clocks	= <&clk NPCM8XX_CLK_AHB>;
+			clock-names = "stmmaceth";
+			pinctrl-names = "default";
+			pinctrl-0 = <&rg2_pins
+					&rg2mdio_pins>;
+			status = "disabled";
+		};
+
+		gmac2: ethernet@f0806000 {
+			device_type = "network";
+			compatible = "snps,dwmac-3.72a", "snps,dwmac";
+			reg = <0x0 0xf0806000 0x0 0x2000>;
+			interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq";
+			clocks	= <&clk NPCM8XX_CLK_AHB>;
+			clock-names = "stmmaceth";
+			pinctrl-names = "default";
+			pinctrl-0 = <&r1_pins
+					&r1err_pins
+					&r1md_pins>;
+			status = "disabled";
+		};
+
+		gmac3: ethernet@f0808000 {
+			device_type = "network";
+			compatible = "snps,dwmac-3.72a", "snps,dwmac";
+			reg = <0x0 0xf0808000 0x0 0x2000>;
+			interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq";
+			clocks	= <&clk NPCM8XX_CLK_AHB>;
+			clock-names = "stmmaceth";
+			pinctrl-names = "default";
+			pinctrl-0 = <&r2_pins
+					&r2err_pins
+					&r2md_pins>;
+			status = "disabled";
+		};
+
+		mc: memory-controller@f0824000 {
+			compatible = "nuvoton,npcm845-memory-controller";
+			reg = <0x0 0xf0824000 0x0 0x1000>;
+			interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		udc0: usb@f0830000 {
+			compatible = "nuvoton,npcm845-udc", "nuvoton,npcm750-udc";
+			reg = <0x0 0xf0830000 0x0 0x1000
+			       0x0 0xfffeb000 0x0 0x800>;
+			interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk NPCM8XX_CLK_SU>;
+			clock-names = "clk_usb_bridge";
+
+			phys = <&udc0_phy>;
+			phy_type = "utmi_wide";
+			dr_mode = "peripheral";
+			status = "disabled";
+		};
+
+		udc1: usb@f0831000 {
+			compatible = "nuvoton,npcm845-udc", "nuvoton,npcm750-udc";
+			reg = <0x0 0xf0831000 0x0 0x1000
+			       0x0 0xfffeb800 0x0 0x800>;
+			interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk NPCM8XX_CLK_SU>;
+			clock-names = "clk_usb_bridge";
+
+			phys = <&udc0_phy>;
+			phy_type = "utmi_wide";
+			dr_mode = "peripheral";
+			status = "disabled";
+		};
+
+		udc2: usb@f0832000 {
+			compatible = "nuvoton,npcm845-udc", "nuvoton,npcm750-udc";
+			reg = <0x0 0xf0832000 0x0 0x1000
+			       0x0 0xfffec000 0x0 0x800>;
+			interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk NPCM8XX_CLK_SU>;
+			clock-names = "clk_usb_bridge";
+
+			phys = <&udc0_phy>;
+			phy_type = "utmi_wide";
+			dr_mode = "peripheral";
+			status = "disabled";
+		};
+
+		udc3: usb@f0833000 {
+			compatible = "nuvoton,npcm845-udc", "nuvoton,npcm750-udc";
+			reg = <0x0 0xf0833000 0x0 0x1000
+			       0x0 0xfffec800 0x0 0x800>;
+			interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk NPCM8XX_CLK_SU>;
+			clock-names = "clk_usb_bridge";
+
+			phys = <&udc0_phy>;
+			phy_type = "utmi_wide";
+			dr_mode = "peripheral";
+			status = "disabled";
+		};
+
+		udc4: usb@f0834000 {
+			compatible = "nuvoton,npcm845-udc", "nuvoton,npcm750-udc";
+			reg = <0x0 0xf0834000 0x0 0x1000
+			       0x0 0xfffed000 0x0 0x800>;
+			interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk NPCM8XX_CLK_SU>;
+			clock-names = "clk_usb_bridge";
+
+			phys = <&udc0_phy>;
+			phy_type = "utmi_wide";
+			dr_mode = "peripheral";
+			status = "disabled";
+		};
+
+		udc5: usb@f0835000 {
+			compatible = "nuvoton,npcm845-udc", "nuvoton,npcm750-udc";
+			reg = <0x0 0xf0835000 0x0 0x1000
+			       0x0 0xfffed800 0x0 0x800>;
+			interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk NPCM8XX_CLK_SU>;
+			clock-names = "clk_usb_bridge";
+
+			phys = <&udc0_phy>;
+			phy_type = "utmi_wide";
+			dr_mode = "peripheral";
+			status = "disabled";
+		};
+
+		udc6: usb@f0836000 {
+			compatible = "nuvoton,npcm845-udc", "nuvoton,npcm750-udc";
+			reg = <0x0 0xf0836000 0x0 0x1000
+			       0x0 0xfffee000 0x0 0x800>;
+			interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk NPCM8XX_CLK_SU>;
+			clock-names = "clk_usb_bridge";
+
+			phys = <&udc0_phy>;
+			phy_type = "utmi_wide";
+			dr_mode = "peripheral";
+			status = "disabled";
+		};
+
+		udc7: usb@f0837000 {
+			compatible = "nuvoton,npcm845-udc", "nuvoton,npcm750-udc";
+			reg = <0x0 0xf0837000 0x0 0x1000
+			       0x0 0xfffee800 0x0 0x800>;
+			interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk NPCM8XX_CLK_SU>;
+			clock-names = "clk_usb_bridge";
+
+			phys = <&udc0_phy>;
+			phy_type = "utmi_wide";
+			dr_mode = "peripheral";
+			status = "disabled";
+		};
+
+		udc8: usb@f0838000 {
+			compatible = "nuvoton,npcm845-udc", "nuvoton,npcm750-udc";
+			reg = <0x0 0xf0838000 0x0 0x1000
+			       0x0 0xfffef000 0x0 0x800>;
+			interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk NPCM8XX_CLK_SU>;
+			clock-names = "clk_usb_bridge";
+
+			nuvoton,sysgcr = <&gcr 0x9C 0xC000 0xC000>;
+			phys = <&udc0_phy>;
+			phy_type = "utmi_wide";
+			dr_mode = "peripheral";
+			status = "disabled";
+		};
+
+		udc9: usb@f0839000 {
+			compatible = "nuvoton,npcm845-udc", "nuvoton,npcm750-udc";
+			reg = <0x0 0xf0839000 0x0 0x1000
+			       0x0 0xfffef800 0x0 0x800>;
+			interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk NPCM8XX_CLK_SU>;
+			clock-names = "clk_usb_bridge";
+
+			nuvoton,sysgcr = <&gcr 0x9C 0x3000 0x3000>;
+			phys = <&udc0_phy>;
+			phy_type = "utmi_wide";
+			dr_mode = "peripheral";
+			status = "disabled";
+		};
+
+		sdhci: mmc@f0842000 {
+			compatible = "nuvoton,npcm845-sdhci";
+			reg = <0x0 0xf0842000 0x0 0x100>;
+			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk NPCM8XX_CLK_AHB>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmc8_pins
+				     &mmc_pins>;
+			status = "disabled";
+		};
+
+		fiu0: spi@fb000000 {
+			compatible = "nuvoton,npcm845-fiu";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0 0xfb000000 0x0 0x1000>;
+			reg-names = "control";
+			clocks =  <&clk NPCM8XX_CLK_SPI0>;
+			clock-names = "clk_ahb";
+			status = "disabled";
+		};
+
+		fiu1: spi@fb002000 {
+			compatible = "nuvoton,npcm845-fiu";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0 0xfb002000 0x0 0x1000>;
+			reg-names = "control";
+			clocks =  <&clk NPCM8XX_CLK_SPI1>;
+			clock-names = "clk_spi1";
+			pinctrl-names = "default";
+			pinctrl-0 = <&spi1_pins>;
+			status = "disabled";
+		};
+
+		fiu3: spi@c0000000 {
+			compatible = "nuvoton,npcm845-fiu";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0 0xc0000000 0x0 0x1000>;
+			reg-names = "control";
+			clocks =  <&clk NPCM8XX_CLK_SPI3>;
+			clock-names = "clk_spi3";
+			pinctrl-names = "default";
+			pinctrl-0 = <&spi3_pins>;
+			status = "disabled";
+		};
+
+		fiux: spi@fb001000 {
+			compatible = "nuvoton,npcm845-fiu";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0 0xfb001000 0x0 0x1000>,
+			<0x0 0xf8000000 0x0 0x2000000>;
+			reg-names = "control", "memory";
+			clocks =  <&clk NPCM8XX_CLK_SPIX>;
+			clock-names = "clk_ahb";
+			status = "disabled";
+		};
+
+
+		apb: bus@f0000000 {
 			#address-cells = <1>;
 			#size-cells = <1>;
 			compatible = "simple-bus";
@@ -164,6 +423,442 @@ peci: peci-controller@100000 {
 				cmd-timeout-ms = <1000>;
 				status = "disabled";
 			};
+
+			rng: rng@b000 {
+				compatible = "nuvoton,npcm845-rng";
+				reg = <0xb000 0x8>;
+				status = "disabled";
+			};
+
+			adc: adc@c000 {
+				compatible = "nuvoton,npcm845-adc";
+				reg = <0xC000 0x8>;
+				interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk NPCM8XX_CLK_ADC>;
+				resets = <&rstc 0x20 27>;
+				status = "disabled";
+			};
+
+			i2c0: i2c@80000 {
+				reg = <0x80000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb0_pins>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c1: i2c@81000 {
+				reg = <0x81000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb1_pins>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c2: i2c@82000 {
+				reg = <0x82000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb2_pins>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c3: i2c@83000 {
+				reg = <0x83000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb3_pins>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c4: i2c@84000 {
+				reg = <0x84000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb4_pins>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c5: i2c@85000 {
+				reg = <0x85000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb5_pins>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c6: i2c@86000 {
+				reg = <0x86000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb6_pins>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c7: i2c@87000 {
+				reg = <0x87000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb7_pins>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c8: i2c@88000 {
+				reg = <0x88000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb8_pins>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c9: i2c@89000 {
+				reg = <0x89000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb9_pins>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c10: i2c@8a000 {
+				reg = <0x8a000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb10_pins>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c11: i2c@8b000 {
+				reg = <0x8b000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb11_pins>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c12: i2c@8c000 {
+				reg = <0x8c000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb12_pins>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c13: i2c@8d000 {
+				reg = <0x8d000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb13_pins>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c14: i2c@8e000 {
+				reg = <0x8e000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb14_pins>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c15: i2c@8f000 {
+				reg = <0x8f000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb15_pins>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c16: i2c@fff00000 {
+				reg = <0xfff00000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb16_pins>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c17: i2c@fff01000 {
+				reg = <0xfff01000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb17_pins>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c18: i2c@fff02000 {
+				reg = <0xfff02000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb18_pins>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c19: i2c@fff03000 {
+				reg = <0xfff03000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb19_pins>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c20: i2c@fff04000 {
+				reg = <0xfff04000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb20_pins>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c21: i2c@fff05000 {
+				reg = <0xfff05000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb21_pins>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c22: i2c@fff06000 {
+				reg = <0xfff06000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb22_pins>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c23: i2c@fff07000 {
+				reg = <0xfff07000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb23_pins>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c24: i2c@fff08000 {
+				reg = <0xfff08000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c25: i2c@fff09000 {
+				reg = <0xfff09000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c26: i2c@fff0a000 {
+				reg = <0xfff0a000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			pwm_fan:pwm-fan-controller@103000 {
+				compatible = "nuvoton,npcm845-pwm-fan";
+				reg = <0x103000 0x3000>,
+					<0x180000 0x8000>;
+				reg-names = "pwm", "fan";
+				clocks =  <&clk NPCM8XX_CLK_APB3>,
+					<&clk NPCM8XX_CLK_APB4>;
+				clock-names = "pwm","fan";
+				interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
+						<GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
+						<GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
+						<GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
+						<GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
+						<GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+						<GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+						<GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pwm0_pins &pwm1_pins
+						&pwm2_pins &pwm3_pins
+						&pwm4_pins &pwm5_pins
+						&pwm6_pins &pwm7_pins
+						&pwm8_pins &pwm9_pins
+						&pwm10_pins &pwm11_pins
+						&fanin0_pins &fanin1_pins
+						&fanin2_pins &fanin3_pins
+						&fanin4_pins &fanin5_pins
+						&fanin6_pins &fanin7_pins
+						&fanin8_pins &fanin9_pins
+						&fanin10_pins &fanin11_pins
+						&fanin12_pins &fanin13_pins
+						&fanin14_pins &fanin15_pins>;
+				status = "disabled";
+			};
+
+			pspi: spi@201000 {
+				compatible = "nuvoton,npcm845-pspi";
+				reg = <0x201000 0x1000>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pspi_pins>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+				clocks =  <&clk NPCM8XX_CLK_APB5>;
+				clock-names = "clk_apb5";
+				resets = <&rstc 0x24 23>;
+				status = "disabled";
+			};
+
 		};
 	};
 
diff --git a/arch/arm64/boot/dts/nuvoton/nuvoton-npcm845.dtsi b/arch/arm64/boot/dts/nuvoton/nuvoton-npcm845.dtsi
index 383938dcd3ce..21dea323612d 100644
--- a/arch/arm64/boot/dts/nuvoton/nuvoton-npcm845.dtsi
+++ b/arch/arm64/boot/dts/nuvoton/nuvoton-npcm845.dtsi
@@ -75,4 +75,11 @@ timer {
 			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
 			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
 	};
+
+	firmware {
+		optee {
+			compatible = "linaro,optee-tz";
+			method = "smc";
+		};
+	};
 };
-- 
2.34.1

[PATCH v3 3/3] arm64: dts: nuvoton: npcm845-evb: Add peripheral nodes

[Tomer Maimon]

Enable peripheral support for the Nuvoton NPCM845 Evaluation Board by
adding device nodes for Ethernet controllers, MMC controller, SPI
controllers, USB device controllers, random number generator, ADC,
PWM-FAN controller, I2C controllers, and PECI interface.
Include MDIO nodes for Ethernet PHYs, reserved memory for TIP, and
aliases for device access.

Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
---
 .../boot/dts/nuvoton/nuvoton-npcm845-evb.dts  | 440 ++++++++++++++++++
 1 file changed, 440 insertions(+)

diff --git a/arch/arm64/boot/dts/nuvoton/nuvoton-npcm845-evb.dts b/arch/arm64/boot/dts/nuvoton/nuvoton-npcm845-evb.dts
index 2638ee1c3846..53e6a0af5a21 100644
--- a/arch/arm64/boot/dts/nuvoton/nuvoton-npcm845-evb.dts
+++ b/arch/arm64/boot/dts/nuvoton/nuvoton-npcm845-evb.dts
@@ -9,6 +9,42 @@ / {
 	compatible = "nuvoton,npcm845-evb", "nuvoton,npcm845";
 
 	aliases {
+		ethernet1 = &gmac1;
+		ethernet2 = &gmac2;
+		ethernet3 = &gmac3;
+		fiu0 = &fiu0;
+		fiu1 = &fiu3;
+		fiu2 = &fiux;
+		fiu3 = &fiu1;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
+		i2c3 = &i2c3;
+		i2c4 = &i2c4;
+		i2c5 = &i2c5;
+		i2c6 = &i2c6;
+		i2c7 = &i2c7;
+		i2c8 = &i2c8;
+		i2c9 = &i2c9;
+		i2c10 = &i2c10;
+		i2c11 = &i2c11;
+		i2c12 = &i2c12;
+		i2c13 = &i2c13;
+		i2c14 = &i2c14;
+		i2c15 = &i2c15;
+		i2c16 = &i2c16;
+		i2c17 = &i2c17;
+		i2c18 = &i2c18;
+		i2c19 = &i2c19;
+		i2c20 = &i2c20;
+		i2c21 = &i2c21;
+		i2c22 = &i2c22;
+		i2c23 = &i2c23;
+		i2c24 = &i2c24;
+		i2c25 = &i2c25;
+		i2c26 = &i2c26;
+		mdio-gpio0 = &mdio0;
+		mdio-gpio1 = &mdio1;
 		serial0 = &serial0;
 	};
 
@@ -16,7 +52,32 @@ chosen {
 		stdout-path = &serial0;
 	};
 
+	mdio0: mdio-0 {
+		compatible = "virtual,mdio-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpios = <&gpio1 25 GPIO_ACTIVE_HIGH>,
+			<&gpio1 26 GPIO_ACTIVE_HIGH>;
+
+		phy0: ethernet-phy@0 {
+			reg = <0>;
+		};
+	};
+
+	mdio1: mdio-1 {
+		compatible = "virtual,mdio-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpios = <&gpio2 27 GPIO_ACTIVE_HIGH>,
+			<&gpio2 28 GPIO_ACTIVE_HIGH>;
+
+		phy1: ethernet-phy@0 {
+			reg = <0>;
+		};
+	};
+
 	memory@0 {
+		device_type = "memory";
 		reg = <0x0 0x0 0x0 0x40000000>;
 	};
 
@@ -25,12 +86,391 @@ refclk: refclk-25mhz {
 		clock-frequency = <25000000>;
 		#clock-cells = <0>;
 	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		tip_reserved: tip@0 {
+			reg = <0x0 0x0 0x0 0x6200000>;
+		};
+	};
+};
+
+&adc {
+	#io-channel-cells = <1>;
+	status = "okay";
+};
+
+&fiu0 {
+	status = "okay";
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		spi-rx-bus-width = <1>;
+		reg = <0>;
+		spi-max-frequency = <5000000>;
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			partition@0 {
+				label = "bb-uboot-1";
+				reg = <0x0000000 0x80000>;
+				read-only;
+				};
+			partition@80000 {
+				label = "bb-uboot-2";
+				reg = <0x0080000 0x80000>;
+				read-only;
+				};
+			partition@100000 {
+				label = "env-param";
+				reg = <0x0100000 0x40000>;
+				read-only;
+				};
+			partition@140000 {
+				label = "spare";
+				reg = <0x0140000 0xC0000>;
+				};
+			partition@200000 {
+				label = "kernel";
+				reg = <0x0200000 0x400000>;
+				};
+			partition@600000 {
+				label = "rootfs";
+				reg = <0x0600000 0x700000>;
+				};
+			partition@d00000 {
+				label = "spare1";
+				reg = <0x0d00000 0x200000>;
+				};
+			partition@f00000 {
+				label = "spare2";
+				reg = <0x0f00000 0x200000>;
+				};
+			partition@1100000 {
+				label = "spare3";
+				reg = <0x1100000 0x200000>;
+				};
+			partition@1300000 {
+				label = "spare4";
+				reg = <0x1300000 0x0>;
+			};
+		};
+	};
+};
+
+&fiu1 {
+	status = "okay";
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		spi-rx-bus-width = <2>;
+		spi-tx-bus-width = <2>;
+		reg = <0>;
+		spi-max-frequency = <5000000>;
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			partition@0 {
+				label = "spi1-system1";
+				reg = <0x0 0x0>;
+			};
+		};
+	};
+};
+
+&fiu3 {
+	pinctrl-0 = <&spi3_pins>, <&spi3quad_pins>;
+	status = "okay";
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		spi-rx-bus-width = <1>;
+		reg = <0>;
+		spi-max-frequency = <5000000>;
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			partition@0 {
+				label = "spi3-system1";
+				reg = <0x0 0x0>;
+			};
+		};
+	};
+};
+
+&fiux {
+	spix-mode;
+};
+
+&gmac1 {
+	phy-mode = "rgmii-id";
+	snps,eee-force-disable;
+	status = "okay";
+};
+
+&gmac2 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&r1_pins
+			&r1oen_pins>;
+	phy-handle = <&phy0>;
+	status = "okay";
+};
+
+&gmac3 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&r2_pins
+			&r2oen_pins>;
+	phy-handle = <&phy1>;
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	eeprom@50 {
+		compatible = "atmel,24c256";
+		reg = <0x50>;
+	};
+};
+
+&i2c2 {
+	status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	ipmb@10 {
+		compatible = "ipmb-dev";
+		reg = <0x10>;
+		i2c-protocol;
+	};
+};
+
+&i2c3 {
+	status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	ipmb@11 {
+		compatible = "ipmb-dev";
+		reg = <0x11>;
+		i2c-protocol;
+	};
+};
+
+&i2c4 {
+	status = "okay";
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&i2c6 {
+	status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	tmp100@48 {
+		compatible = "tmp100";
+		reg = <0x48>;
+		status = "okay";
+	};
+};
+
+&i2c7 {
+	status = "okay";
+};
+
+&i2c8 {
+	status = "okay";
+};
+
+&i2c9 {
+	status = "okay";
+};
+
+&i2c10 {
+	status = "okay";
+};
+
+&i2c11 {
+	status = "okay";
+};
+
+&i2c12 {
+	status = "okay";
+};
+
+&i2c13 {
+	status = "okay";
+};
+
+&i2c14 {
+	status = "okay";
+};
+
+&i2c15 {
+	status = "okay";
+};
+
+&i2c16 {
+	status = "okay";
+};
+
+&i2c17 {
+	status = "okay";
+};
+
+&i2c18 {
+	status = "okay";
+};
+
+&i2c19 {
+	status = "okay";
+};
+
+&i2c20 {
+	status = "okay";
+};
+
+&i2c21 {
+	status = "okay";
+};
+
+&i2c22 {
+	status = "okay";
+};
+
+&i2c23 {
+	status = "okay";
+};
+
+&i2c24 {
+	status = "okay";
+};
+
+&i2c25 {
+	status = "okay";
+};
+
+&i2c26 {
+	status = "okay";
+};
+
+&mc {
+	status = "okay";
+};
+
+&peci {
+	status = "okay";
+};
+
+&pwm_fan {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_pins &pwm1_pins
+		&pwm2_pins &pwm3_pins
+		&pwm4_pins &pwm5_pins
+		&pwm6_pins &pwm7_pins
+		&fanin0_pins &fanin1_pins
+		&fanin2_pins &fanin3_pins
+		&fanin4_pins &fanin5_pins
+		&fanin6_pins &fanin7_pins>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	fan@0 {
+		reg = <0x00>;
+		fan-tach-ch = <0x0 0x1>;
+		cooling-levels = <127 255>;
+	};
+	fan@1 {
+		reg = <0x01>;
+		fan-tach-ch = <0x2 0x3>;
+		cooling-levels = <127 255>;
+	};
+	fan@2 {
+		reg = <0x02>;
+		fan-tach-ch = <0x4 0x5>;
+		cooling-levels = <127 255>;
+	};
+	fan@3 {
+		reg = <0x03>;
+		fan-tach-ch = <0x6 0x7>;
+		cooling-levels = <127 255>;
+	};
+	fan@4 {
+		reg = <0x04>;
+		fan-tach-ch = <0x8 0x9>;
+		cooling-levels = <127 255>;
+	};
+	fan@5 {
+		reg = <0x05>;
+		fan-tach-ch = <0xa 0xb>;
+		cooling-levels = <127 255>;
+	};
+	fan@6 {
+		reg = <0x06>;
+		fan-tach-ch = <0xc 0xd>;
+		cooling-levels = <127 255>;
+	};
+	fan@7 {
+		reg = <0x07>;
+		fan-tach-ch = <0xe 0xf>;
+		cooling-levels = <127 255>;
+	};
+};
+
+&rng {
+	status = "okay";
+};
+
+&sdhci {
+	status = "okay";
 };
 
 &serial0 {
 	status = "okay";
 };
 
+&udc0 {
+	status = "okay";
+};
+
+&udc1 {
+	status = "okay";
+};
+
+&udc2 {
+	status = "okay";
+};
+
+&udc3 {
+	status = "okay";
+};
+
+&udc4 {
+	status = "okay";
+};
+
+&udc5 {
+	status = "okay";
+};
+
+&udc6 {
+	status = "okay";
+};
+
+&udc7 {
+	status = "okay";
+};
+
 &watchdog1 {
 	status = "okay";
 };
-- 
2.34.1

Re: [PATCH v3 0/3] arm64: dts: nuvoton: add NPCM845 SoC and EVB support

[Rob Herring (Arm)]

On Thu, 25 Sep 2025 23:06:22 +0300, Tomer Maimon wrote:
> This series fix warnings and adds device tree support for peripherals on
> the Nuvoton NPCM845 SoC and its Evaluation Board (EVB).
> The first patch fix warning and arrange node order.
> The second patch introduces peripheral nodes for Ethernet, MMC, SPI, USB,
> RNG, ADC, PWM-FAN, I2C, and OP-TEE firmware in the NPCM845 SoC device tree.
> The third patch enables these peripherals for the NPCM845-EVB, adding
> MDIO nodes, reserved memory, aliases, and board-specific configurations
> like PHY modes and SPI flash partitions.
> 
> The NPCM8XX device tree tested on NPCM845 evaluation board.
> 
> Addressed comments from:
> 	- Andrew Jeffery: https://patchwork.ozlabs.org/project/openbmc/patch/20250908125938.3584927-2-tmaimon77@gmail.com/
> 					  https://patchwork.ozlabs.org/project/openbmc/patch/20250908125938.3584927-3-tmaimon77@gmail.com/
> 
> Changes since version 2:
> 	- Fix dts warning
> 	- Arrange node order by ascending unit address.
> 
> Changes since version 1:
> 	- Fix commit message
> 	- Fix dtbs_check warnings.
> 
> Tomer Maimon (3):
>   arm64: dts: nuvoton: fix warning and nodes order
>   arm64: dts: nuvoton: npcm845: Add peripheral nodes
>   arm64: dts: nuvoton: npcm845-evb: Add peripheral nodes
> 
>  .../dts/nuvoton/nuvoton-common-npcm8xx.dtsi   | 732 +++++++++++++++++-
>  .../boot/dts/nuvoton/nuvoton-npcm845-evb.dts  | 440 +++++++++++
>  .../boot/dts/nuvoton/nuvoton-npcm845.dtsi     |   7 +
>  3 files changed, 1160 insertions(+), 19 deletions(-)
> 
> --
> 2.34.1
> 
> 
> 


My bot found new DTB warnings on the .dts files added or changed in this
series.

Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings
are fixed by another series. Ultimately, it is up to the platform
maintainer whether these warnings are acceptable or not. No need to reply
unless the platform maintainer has comments.

If you already ran DT checks and didn't see these error(s), then
make sure dt-schema is up to date:

  pip3 install dtschema --upgrade


This patch series was applied (using b4) to base:
 Base: attempting to guess base-commit...
 Base: remotes/arm-soc/for-next-12027-gf60eaa447dab (exact match)

If this is not the correct base, please add 'base-commit' tag
(or use b4 which does this automatically)

New warnings running 'make CHECK_DTBS=y for arch/arm64/boot/dts/nuvoton/' for 20250925200625.573902-1-tmaimon77@gmail.com:

arch/arm64/boot/dts/nuvoton/nuvoton-npcm845-evb.dtb: /ahb/spi@fb000000: failed to match any schema with compatible: ['nuvoton,npcm845-fiu']
arch/arm64/boot/dts/nuvoton/nuvoton-npcm845-evb.dtb: /ahb/spi@fb002000: failed to match any schema with compatible: ['nuvoton,npcm845-fiu']
arch/arm64/boot/dts/nuvoton/nuvoton-npcm845-evb.dtb: /ahb/spi@c0000000: failed to match any schema with compatible: ['nuvoton,npcm845-fiu']
arch/arm64/boot/dts/nuvoton/nuvoton-npcm845-evb.dtb: /ahb/spi@fb001000: failed to match any schema with compatible: ['nuvoton,npcm845-fiu']
arch/arm64/boot/dts/nuvoton/nuvoton-npcm845-evb.dtb: /ahb/bus@f0000000/i2c@86000/tmp100@48: failed to match any schema with compatible: ['tmp100']
arch/arm64/boot/dts/nuvoton/nuvoton-npcm845-evb.dtb: /ahb/bus@f0000000/pwm-fan-controller@103000: failed to match any schema with compatible: ['nuvoton,npcm845-pwm-fan']
arch/arm64/boot/dts/nuvoton/nuvoton-npcm845-evb.dtb: /ahb/bus@f0000000/spi@201000: failed to match any schema with compatible: ['nuvoton,npcm845-pspi']

Re: [PATCH v3 0/3] arm64: dts: nuvoton: add NPCM845 SoC and EVB support

[Tomer Maimon]

Hi Rob,

Thanks for your comments

Most of the warnings occur because the compatible strings are located
in .txt device tree binding rather than in the .yaml file.

The only change that needs to be done is in ti,tmp100 that

Could you approve the patches, avoiding NPCM845 compatible warnings?
Meanwhile, I will work on converting the txt to yaml

Thanks,

Tomer


On Fri, 26 Sept 2025 at 19:11, Rob Herring (Arm) <robh@kernel.org> wrote:
>
>
> On Thu, 25 Sep 2025 23:06:22 +0300, Tomer Maimon wrote:
> > This series fix warnings and adds device tree support for peripherals on
> > the Nuvoton NPCM845 SoC and its Evaluation Board (EVB).
> > The first patch fix warning and arrange node order.
> > The second patch introduces peripheral nodes for Ethernet, MMC, SPI, USB,
> > RNG, ADC, PWM-FAN, I2C, and OP-TEE firmware in the NPCM845 SoC device tree.
> > The third patch enables these peripherals for the NPCM845-EVB, adding
> > MDIO nodes, reserved memory, aliases, and board-specific configurations
> > like PHY modes and SPI flash partitions.
> >
> > The NPCM8XX device tree tested on NPCM845 evaluation board.
> >
> > Addressed comments from:
> >       - Andrew Jeffery: https://patchwork.ozlabs.org/project/openbmc/patch/20250908125938.3584927-2-tmaimon77@gmail.com/
> >                                         https://patchwork.ozlabs.org/project/openbmc/patch/20250908125938.3584927-3-tmaimon77@gmail.com/
> >
> > Changes since version 2:
> >       - Fix dts warning
> >       - Arrange node order by ascending unit address.
> >
> > Changes since version 1:
> >       - Fix commit message
> >       - Fix dtbs_check warnings.
> >
> > Tomer Maimon (3):
> >   arm64: dts: nuvoton: fix warning and nodes order
> >   arm64: dts: nuvoton: npcm845: Add peripheral nodes
> >   arm64: dts: nuvoton: npcm845-evb: Add peripheral nodes
> >
> >  .../dts/nuvoton/nuvoton-common-npcm8xx.dtsi   | 732 +++++++++++++++++-
> >  .../boot/dts/nuvoton/nuvoton-npcm845-evb.dts  | 440 +++++++++++
> >  .../boot/dts/nuvoton/nuvoton-npcm845.dtsi     |   7 +
> >  3 files changed, 1160 insertions(+), 19 deletions(-)
> >
> > --
> > 2.34.1
> >
> >
> >
>
>
> My bot found new DTB warnings on the .dts files added or changed in this
> series.
>
> Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings
> are fixed by another series. Ultimately, it is up to the platform
> maintainer whether these warnings are acceptable or not. No need to reply
> unless the platform maintainer has comments.
>
> If you already ran DT checks and didn't see these error(s), then
> make sure dt-schema is up to date:
>
>   pip3 install dtschema --upgrade
>
>
> This patch series was applied (using b4) to base:
>  Base: attempting to guess base-commit...
>  Base: remotes/arm-soc/for-next-12027-gf60eaa447dab (exact match)
>
> If this is not the correct base, please add 'base-commit' tag
> (or use b4 which does this automatically)
>
> New warnings running 'make CHECK_DTBS=y for arch/arm64/boot/dts/nuvoton/' for 20250925200625.573902-1-tmaimon77@gmail.com:
>
> arch/arm64/boot/dts/nuvoton/nuvoton-npcm845-evb.dtb: /ahb/spi@fb000000: failed to match any schema with compatible: ['nuvoton,npcm845-fiu']
> arch/arm64/boot/dts/nuvoton/nuvoton-npcm845-evb.dtb: /ahb/spi@fb002000: failed to match any schema with compatible: ['nuvoton,npcm845-fiu']
> arch/arm64/boot/dts/nuvoton/nuvoton-npcm845-evb.dtb: /ahb/spi@c0000000: failed to match any schema with compatible: ['nuvoton,npcm845-fiu']
> arch/arm64/boot/dts/nuvoton/nuvoton-npcm845-evb.dtb: /ahb/spi@fb001000: failed to match any schema with compatible: ['nuvoton,npcm845-fiu']
> arch/arm64/boot/dts/nuvoton/nuvoton-npcm845-evb.dtb: /ahb/bus@f0000000/i2c@86000/tmp100@48: failed to match any schema with compatible: ['tmp100']
> arch/arm64/boot/dts/nuvoton/nuvoton-npcm845-evb.dtb: /ahb/bus@f0000000/pwm-fan-controller@103000: failed to match any schema with compatible: ['nuvoton,npcm845-pwm-fan']
> arch/arm64/boot/dts/nuvoton/nuvoton-npcm845-evb.dtb: /ahb/bus@f0000000/spi@201000: failed to match any schema with compatible: ['nuvoton,npcm845-pspi']
>
>
>
>
>

Re: [PATCH v3 0/3] arm64: dts: nuvoton: add NPCM845 SoC and EVB support

[Andrew Jeffery]

On Mon, 2025-09-29 at 12:15 +0300, Tomer Maimon wrote:
> Hi Rob,
> 
> Thanks for your comments
> 
> Most of the warnings occur because the compatible strings are located
> in .txt device tree binding rather than in the .yaml file.
> 
> The only change that needs to be done is in ti,tmp100 that
> 
> Could you approve the patches, avoiding NPCM845 compatible warnings?
> Meanwhile, I will work on converting the txt to yaml

I think it's best we get the conversion done, and then subsequently
apply the apply this series. See:

https://docs.kernel.org/process/maintainer-soc.html#validating-devicetree-files

and

https://docs.kernel.org/process/maintainer-soc-clean-dts.html#strict-dts-dt-schema-and-dtc-compliance

Andrew

Re: [PATCH v3 0/3] arm64: dts: nuvoton: add NPCM845 SoC and EVB support

[Tomer Maimon]

Sure, thanks Andrew

On Wed, 1 Oct 2025 at 05:35, Andrew Jeffery <andrew@codeconstruct.com.au> wrote:
>
> On Mon, 2025-09-29 at 12:15 +0300, Tomer Maimon wrote:
> > Hi Rob,
> >
> > Thanks for your comments
> >
> > Most of the warnings occur because the compatible strings are located
> > in .txt device tree binding rather than in the .yaml file.
> >
> > The only change that needs to be done is in ti,tmp100 that
> >
> > Could you approve the patches, avoiding NPCM845 compatible warnings?
> > Meanwhile, I will work on converting the txt to yaml
>
> I think it's best we get the conversion done, and then subsequently
> apply the apply this series. See:
>
> https://docs.kernel.org/process/maintainer-soc.html#validating-devicetree-files
>
> and
>
> https://docs.kernel.org/process/maintainer-soc-clean-dts.html#strict-dts-dt-schema-and-dtc-compliance
>
> Andrew

Re: [PATCH v3 1/3] arm64: dts: nuvoton: fix warning and nodes order

[Krzysztof Kozlowski]

On 25/09/2025 22:06, Tomer Maimon wrote:
> Fix the warning in the gcr and timer nodes, and modify nodes order by

What warning?

> ascending unit address.

Why are you combining multiple issues into one commit. No. Read
submitting patches how to organize your work.

> 
> Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
> ---
>  .../dts/nuvoton/nuvoton-common-npcm8xx.dtsi   | 35 +++++++++----------
>  1 file changed, 17 insertions(+), 18 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/nuvoton/nuvoton-common-npcm8xx.dtsi b/arch/arm64/boot/dts/nuvoton/nuvoton-common-npcm8xx.dtsi
> index 24133528b8e9..a43514f624c0 100644
> --- a/arch/arm64/boot/dts/nuvoton/nuvoton-common-npcm8xx.dtsi
> +++ b/arch/arm64/boot/dts/nuvoton/nuvoton-common-npcm8xx.dtsi
> @@ -18,7 +18,7 @@ soc {
>  		ranges;
>  
>  		gcr: system-controller@f0800000 {
> -			compatible = "nuvoton,npcm845-gcr", "syscon";
> +			compatible = "nuvoton,npcm845-gcr", "syscon", "simple-mfd";

This makes no sense. No children here.

>  			reg = <0x0 0xf0800000 0x0 0x1000>;
>  		};
>  
Best regards,
Krzysztof

Re: [PATCH v3 1/3] arm64: dts: nuvoton: fix warning and nodes order

[Krzysztof Kozlowski]

On 19/10/2025 16:30, Tomer Maimon wrote:
> Hi Krzysztof,
> 
> Thanks for your comments
> 
> On Sun, 19 Oct 2025 at 13:35, Krzysztof Kozlowski <krzk@kernel.org> wrote:
>>
>> On 25/09/2025 22:06, Tomer Maimon wrote:
>>> Fix the warning in the gcr and timer nodes, and modify nodes order by
>>
>> What warning?
> This warning that I got from Andrew mail
> [I] 0 andrew@heihei ~/s/k/l/o/build.arm64.default ((00e2ab2e))> make
> CHECK_DTBS=y nuvoton/nuvoton-npcm845-evb.dtb
>   SCHEMA  Documentation/devicetree/bindings/processed-schema.json
>   DTC [C] arch/arm64/boot/dts/nuvoton/nuvoton-npcm845-evb.dtb
> /home/andrew/src/
> kernel.org/linux/origin/build.arm64.default/arch/arm64/boot/dts/nuvoton/nuvoton-npcm845-evb.dtb:
> / (nuvoton,npcm845-evb): memory@0: 'device_type' is a required property
>         from schema $id: http://devicetree.org/schemas/memory.yaml#


Commit msg should explain that. See git history how to add such
information to the commit msg.

Anyway, all other comments stay valid and I expect improved/different fixes.

You don't sprinkle random compatibles because someone or something told
you, right?

Best regards,
Krzysztof