From: Jonathan Cameron <jic23@kernel.org>
To: Krzysztof Kozlowski <krzk@kernel.org>
Cc: "Petre Rodan" <petre.rodan@subdimension.ro>,
"David Lechner" <dlechner@baylibre.com>,
"Nuno Sá" <nuno.sa@analog.com>,
"Andy Shevchenko" <andy@kernel.org>,
"Rob Herring" <robh@kernel.org>,
"Krzysztof Kozlowski" <krzk+dt@kernel.org>,
"Conor Dooley" <conor+dt@kernel.org>,
"Jonathan Cameron" <Jonathan.Cameron@huawei.com>,
linux-iio@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org
Subject: Re: [PATCH v3 03/18] dt-bindings: iio: accel: bosch,bma220 set irq type in example block
Date: Sat, 27 Sep 2025 15:00:36 +0100 [thread overview]
Message-ID: <20250927150036.40b66484@jic23-huawei> (raw)
In-Reply-To: <20250918-brave-khaki-sloth-b0b7dd@kuoka>
On Thu, 18 Sep 2025 11:08:59 +0900
Krzysztof Kozlowski <krzk@kernel.org> wrote:
> On Sat, Sep 13, 2025 at 06:39:24PM +0300, Petre Rodan wrote:
> > Set the interrupt type to rising edge within the example block in order
> > to match the new driver.
> >
> > The entry that got replaced was not in use by the original driver.
> >
> > Signed-off-by: Petre Rodan <petre.rodan@subdimension.ro>
> > ---
>
> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
>
In the interests of reducing what you need to post for v4, I've
picked up these first 3 patches and applied them to the testing
branch of iio.git. That will get rebased on rc1 once available.
Thanks,
Jonathan
> Best regards,
> Krzysztof
>
next prev parent reply other threads:[~2025-09-27 14:00 UTC|newest]
Thread overview: 36+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-09-13 15:39 [PATCH v3 00/18] iio: accel: bma220 improvements Petre Rodan
2025-09-13 15:39 ` [PATCH v3 01/18] dt-bindings: iio: accel: bosch,bma220 cleanup typo Petre Rodan
2025-09-13 15:39 ` [PATCH v3 02/18] dt-bindings: iio: accel: bosch,bma220 setup SPI clock mode Petre Rodan
2025-09-13 15:39 ` [PATCH v3 03/18] dt-bindings: iio: accel: bosch,bma220 set irq type in example block Petre Rodan
2025-09-18 2:08 ` Krzysztof Kozlowski
2025-09-27 14:00 ` Jonathan Cameron [this message]
2025-09-13 15:39 ` [PATCH v3 04/18] iio: accel: bma220: split original driver Petre Rodan
2025-09-14 12:45 ` Andy Shevchenko
2025-09-15 5:05 ` Petre Rodan
2025-09-13 15:39 ` [PATCH v3 05/18] iio: accel: bma220: add open firmware table Petre Rodan
2025-09-13 15:39 ` [PATCH v3 06/18] iio: accel: bma220: turn power supplies on Petre Rodan
2025-09-14 12:04 ` Andy Shevchenko
2025-09-13 15:39 ` [PATCH v3 07/18] iio: accel: bma220: move bma220_power() fct Petre Rodan
2025-09-14 12:05 ` Andy Shevchenko
2025-09-27 14:04 ` Jonathan Cameron
2025-09-13 15:39 ` [PATCH v3 08/18] iio: accel: bma220: reset registers during init stage Petre Rodan
2025-09-14 12:07 ` Andy Shevchenko
2025-09-13 15:39 ` [PATCH v3 09/18] iio: accel: bma220: relax constraints during probe() Petre Rodan
2025-09-14 12:13 ` Andy Shevchenko
2025-09-13 15:39 ` [PATCH v3 10/18] iio: accel: bma220: migrate to regmap API Petre Rodan
2025-09-14 12:21 ` Andy Shevchenko
2025-09-15 5:49 ` Petre Rodan
2025-09-13 15:39 ` [PATCH v3 11/18] iio: accel: bma220: populate buffer ts in trigger handler Petre Rodan
2025-09-27 14:07 ` Jonathan Cameron
2025-09-13 15:39 ` [PATCH v3 12/18] iio: accel: bma220: use find_match_table fct Petre Rodan
2025-09-13 15:39 ` [PATCH v3 13/18] iio: accel: bma220: add i2c module Petre Rodan
2025-09-13 15:39 ` [PATCH v3 14/18] iio: accel: bma220: add i2c watchdog feature Petre Rodan
2025-09-13 15:39 ` [PATCH v3 15/18] iio: accel: bma220: add interrupt trigger Petre Rodan
2025-09-13 16:32 ` Petre Rodan
2025-09-14 12:09 ` Andy Shevchenko
2025-09-13 18:12 ` kernel test robot
2025-09-14 12:12 ` Andy Shevchenko
2025-09-27 14:12 ` Jonathan Cameron
2025-09-13 15:39 ` [PATCH v3 16/18] iio: accel: bma220: add LPF cut-off frequency mapping Petre Rodan
2025-09-13 15:39 ` [PATCH v3 17/18] iio: accel: bma220: add debugfs reg access Petre Rodan
2025-09-13 15:39 ` [PATCH v3 18/18] iio: accel: bma220: add maintainer Petre Rodan
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20250927150036.40b66484@jic23-huawei \
--to=jic23@kernel.org \
--cc=Jonathan.Cameron@huawei.com \
--cc=andy@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=dlechner@baylibre.com \
--cc=krzk+dt@kernel.org \
--cc=krzk@kernel.org \
--cc=linux-iio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=nuno.sa@analog.com \
--cc=petre.rodan@subdimension.ro \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox