[PATCH v7 RESEND 0/7] ARM: dts: aspeed: Add Balcones system

[PATCH v7 RESEND 0/7] ARM: dts: aspeed: Add Balcones system

[Eddie James]

Resending this series to iio and hwmon maintainers too. Andrew J has merged the
dts changes with the Aspeed tree already.

The Balcones system is similar to Bonnell but with a POWER11 processor.

Changes since v6:
 - Remove un-documented fan properties under max31785 nodes
 - Change fan-x to fan@x in max31790 documentation.

Changes since v5:
 - Add patch to add address and size cells to max31790 document
 - Don't remove address and size cells in max31785 fixes change

Changes since v4:
 - Add patch to fix max31785 warnings
 - Add patch to fix missing Bonnell documentation

Changes since v3:
 - Add max31785 to the max31790 document instead of to trivial-devices
 - Fix minor formatting in dps310 document

Changes since v2:
 - Fix a couple of incorrect i2c addresses
 - Document dps310 and max31785 properly
 - Drop the UCD binding documentation update, it's been fixed

Changes since v1:
 - Add all the ucd9000 driver supported compatible strings
 - Fix node ordering in Balcones device tree
 - Improve commit message to explain addition of ibm-power11-dual.dtsi

Eddie James (7):
  dt-bindings: arm: aspeed: add IBM Balcones board
  dt-bindings: arm: aspeed: add IBM Bonnell board
  dt-bindings: iio: Add Infineon DPS310 sensor documentation
  dt-bindings: hwmon: Move max31785 compatibles to max31790 document
  dt-bindings: hwmon: max31790: Use addressed fan nodes
  ARM: dts: aspeed: Add Balcones system
  ARM: dts: aspeed: Fix max31785 fan properties

 .../bindings/arm/aspeed/aspeed.yaml           |   2 +
 .../devicetree/bindings/hwmon/max31785.txt    |  22 -
 .../bindings/hwmon/maxim,max31790.yaml        |  22 +-
 .../iio/pressure/infineon,dps310.yaml         |  44 +
 .../devicetree/bindings/trivial-devices.yaml  |   2 -
 MAINTAINERS                                   |   1 +
 arch/arm/boot/dts/aspeed/Makefile             |   1 +
 .../dts/aspeed/aspeed-bmc-ibm-balcones.dts    | 609 ++++++++++++++
 .../dts/aspeed/aspeed-bmc-ibm-bonnell.dts     |   4 -
 .../dts/aspeed/aspeed-bmc-ibm-everest.dts     |   8 -
 .../dts/aspeed/aspeed-bmc-ibm-rainier.dts     |  12 -
 .../boot/dts/aspeed/aspeed-bmc-opp-tacoma.dts |  36 -
 .../arm/boot/dts/aspeed/ibm-power11-dual.dtsi | 779 ++++++++++++++++++
 .../arm/boot/dts/aspeed/ibm-power11-quad.dtsi | 769 +----------------
 14 files changed, 1456 insertions(+), 855 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/hwmon/max31785.txt
 create mode 100644 Documentation/devicetree/bindings/iio/pressure/infineon,dps310.yaml
 create mode 100644 arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-balcones.dts
 create mode 100644 arch/arm/boot/dts/aspeed/ibm-power11-dual.dtsi

-- 
2.51.0

[PATCH v7 RESEND 1/7] dt-bindings: arm: aspeed: add IBM Balcones board

[Eddie James]

Document a new AST2600 BMC board for IBM P11 server.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
---
 Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml b/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
index aedefca7cf4a8..b2fcfcc4a3b9a 100644
--- a/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
+++ b/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
@@ -93,6 +93,7 @@ properties:
               - facebook,minerva-cmc
               - facebook,santabarbara-bmc
               - facebook,yosemite4-bmc
+              - ibm,balcones-bmc
               - ibm,blueridge-bmc
               - ibm,everest-bmc
               - ibm,fuji-bmc
-- 
2.51.0

[PATCH v7 RESEND 2/7] dt-bindings: arm: aspeed: add IBM Bonnell board

[Eddie James]

Document the existing AST2600 BMC board for IBM P10 server.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
---
 Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml b/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
index b2fcfcc4a3b9a..9730df98b945a 100644
--- a/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
+++ b/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
@@ -95,6 +95,7 @@ properties:
               - facebook,yosemite4-bmc
               - ibm,balcones-bmc
               - ibm,blueridge-bmc
+              - ibm,bonnell-bmc
               - ibm,everest-bmc
               - ibm,fuji-bmc
               - ibm,rainier-bmc
-- 
2.51.0

[PATCH v7 RESEND 3/7] dt-bindings: iio: Add Infineon DPS310 sensor documentation

[Eddie James]

The DPS310 is a barometric pressure and temperature sensor with
an I2C interface. Remove it from trivial-devices.yaml and add its
own documentation.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
---
 .../iio/pressure/infineon,dps310.yaml         | 44 +++++++++++++++++++
 .../devicetree/bindings/trivial-devices.yaml  |  2 -
 MAINTAINERS                                   |  1 +
 3 files changed, 45 insertions(+), 2 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/iio/pressure/infineon,dps310.yaml

diff --git a/Documentation/devicetree/bindings/iio/pressure/infineon,dps310.yaml b/Documentation/devicetree/bindings/iio/pressure/infineon,dps310.yaml
new file mode 100644
index 0000000000000..7c0782e2a821b
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/pressure/infineon,dps310.yaml
@@ -0,0 +1,44 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/pressure/infineon,dps310.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Infineon DPS310 barometric pressure and temperature sensor
+
+maintainers:
+  - Eddie James <eajames@linux.ibm.com>
+
+description:
+  The DPS310 is a barometric pressure and temperature sensor with an I2C
+  interface.
+
+properties:
+  compatible:
+    enum:
+      - infineon,dps310
+
+  reg:
+    maxItems: 1
+
+  "#io-channel-cells":
+    const: 0
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        pressure-sensor@76 {
+          compatible = "infineon,dps310";
+          reg = <0x76>;
+          #io-channel-cells = <0>;
+        };
+    };
diff --git a/Documentation/devicetree/bindings/trivial-devices.yaml b/Documentation/devicetree/bindings/trivial-devices.yaml
index 7609acaa752d5..a72b7fabc7034 100644
--- a/Documentation/devicetree/bindings/trivial-devices.yaml
+++ b/Documentation/devicetree/bindings/trivial-devices.yaml
@@ -127,8 +127,6 @@ properties:
           - ibm,cffps2
             # IBM On-Chip Controller hwmon device
           - ibm,p8-occ-hwmon
-            # Infineon barometric pressure and temperature sensor
-          - infineon,dps310
             # Infineon IR36021 digital POL buck controller
           - infineon,ir36021
             # Infineon IRPS5401 Voltage Regulator (PMIC)
diff --git a/MAINTAINERS b/MAINTAINERS
index 0c8281ea4cc64..92b9854a0e07d 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -12191,6 +12191,7 @@ INFINEON DPS310 Driver
 M:	Eddie James <eajames@linux.ibm.com>
 L:	linux-iio@vger.kernel.org
 S:	Maintained
+F:	Documentation/devicetree/bindings/iio/pressure/infineon,dps310.yaml
 F:	drivers/iio/pressure/dps310.c
 
 INFINEON PEB2466 ASoC CODEC
-- 
2.51.0

[PATCH v7 RESEND 4/7] dt-bindings: hwmon: Move max31785 compatibles to max31790 document

[Eddie James]

The binding for the max31785 is the same as the max31790, so just add
some compatible strings for the max31785 chip.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
---
 .../devicetree/bindings/hwmon/max31785.txt    | 22 -------------------
 .../bindings/hwmon/maxim,max31790.yaml        |  6 ++++-
 2 files changed, 5 insertions(+), 23 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/hwmon/max31785.txt

diff --git a/Documentation/devicetree/bindings/hwmon/max31785.txt b/Documentation/devicetree/bindings/hwmon/max31785.txt
deleted file mode 100644
index 106e08c56aaa9..0000000000000
--- a/Documentation/devicetree/bindings/hwmon/max31785.txt
+++ /dev/null
@@ -1,22 +0,0 @@
-Bindings for the Maxim MAX31785 Intelligent Fan Controller
-==========================================================
-
-Reference:
-
-https://datasheets.maximintegrated.com/en/ds/MAX31785.pdf
-
-The Maxim MAX31785 is a PMBus device providing closed-loop, multi-channel fan
-management with temperature and remote voltage sensing. Various fan control
-features are provided, including PWM frequency control, temperature hysteresis,
-dual tachometer measurements, and fan health monitoring.
-
-Required properties:
-- compatible     : One of "maxim,max31785" or "maxim,max31785a"
-- reg            : I2C address, one of 0x52, 0x53, 0x54, 0x55.
-
-Example:
-
-        fans@52 {
-                compatible = "maxim,max31785";
-                reg = <0x52>;
-        };
diff --git a/Documentation/devicetree/bindings/hwmon/maxim,max31790.yaml b/Documentation/devicetree/bindings/hwmon/maxim,max31790.yaml
index b1ff496f87f95..b2dc813b1ab44 100644
--- a/Documentation/devicetree/bindings/hwmon/maxim,max31790.yaml
+++ b/Documentation/devicetree/bindings/hwmon/maxim,max31790.yaml
@@ -20,7 +20,11 @@ description: >
 
 properties:
   compatible:
-    const: maxim,max31790
+    enum:
+      - maxim,max31785
+      - maxim,max31785a
+      - maxim,max31785b
+      - maxim,max31790
 
   reg:
     maxItems: 1
-- 
2.51.0

[PATCH v7 RESEND 5/7] dt-bindings: hwmon: max31790: Use addressed fan nodes

[Eddie James]

Since fan properties can include reg, the fan controller should be
able to specify address-cells and size-cells properties and use
an addressed fan child node.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
---
 .../bindings/hwmon/maxim,max31790.yaml           | 16 +++++++++++++---
 1 file changed, 13 insertions(+), 3 deletions(-)

diff --git a/Documentation/devicetree/bindings/hwmon/maxim,max31790.yaml b/Documentation/devicetree/bindings/hwmon/maxim,max31790.yaml
index b2dc813b1ab44..558cbd251b0fd 100644
--- a/Documentation/devicetree/bindings/hwmon/maxim,max31790.yaml
+++ b/Documentation/devicetree/bindings/hwmon/maxim,max31790.yaml
@@ -35,11 +35,17 @@ properties:
   resets:
     maxItems: 1
 
+  '#address-cells':
+    const: 1
+
+  '#size-cells':
+    const: 0
+
   "#pwm-cells":
     const: 1
 
 patternProperties:
-  "^fan-[0-9]+$":
+  "^fan@[0-9]+$":
     $ref: fan-common.yaml#
     unevaluatedProperties: false
 
@@ -60,13 +66,17 @@ examples:
         reg = <0x20>;
         clocks = <&sys_clk>;
         resets = <&reset 0>;
+        #address-cells = <1>;
         #pwm-cells = <1>;
+        #size-cells = <0>;
 
-        fan-0 {
+        fan@0 {
+          reg = <0x0>;
           pwms = <&pwm_provider 1>;
         };
 
-        fan-1 {
+        fan@1 {
+          reg = <0x1>;
           pwms = <&pwm_provider 2>;
         };
       };
-- 
2.51.0

[PATCH v7 RESEND 6/7] ARM: dts: aspeed: Add Balcones system

[Eddie James]

The Balcones system is similar to Bonnell but with a POWER11 processor.
Like POWER10, the POWER11 is a dual-chip module, so a dual chip FSI
tree is needed. Therefore, split up the quad chip FSI tree.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
---
 arch/arm/boot/dts/aspeed/Makefile             |   1 +
 .../dts/aspeed/aspeed-bmc-ibm-balcones.dts    | 609 ++++++++++++++
 .../arm/boot/dts/aspeed/ibm-power11-dual.dtsi | 779 ++++++++++++++++++
 .../arm/boot/dts/aspeed/ibm-power11-quad.dtsi | 769 +----------------
 4 files changed, 1391 insertions(+), 767 deletions(-)
 create mode 100644 arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-balcones.dts
 create mode 100644 arch/arm/boot/dts/aspeed/ibm-power11-dual.dtsi

diff --git a/arch/arm/boot/dts/aspeed/Makefile b/arch/arm/boot/dts/aspeed/Makefile
index 0f0b5b7076545..b56429777c7ef 100644
--- a/arch/arm/boot/dts/aspeed/Makefile
+++ b/arch/arm/boot/dts/aspeed/Makefile
@@ -39,6 +39,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
 	aspeed-bmc-facebook-yamp.dtb \
 	aspeed-bmc-facebook-yosemitev2.dtb \
 	aspeed-bmc-facebook-yosemite4.dtb \
+	aspeed-bmc-ibm-balcones.dtb \
 	aspeed-bmc-ibm-blueridge.dtb \
 	aspeed-bmc-ibm-bonnell.dtb \
 	aspeed-bmc-ibm-everest.dtb \
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-balcones.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-balcones.dts
new file mode 100644
index 0000000000000..63fcb7a7619ab
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-balcones.dts
@@ -0,0 +1,609 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright 2025 IBM Corp.
+/dts-v1/;
+
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/i2c/i2c.h>
+#include <dt-bindings/leds/leds-pca955x.h>
+#include "aspeed-g6.dtsi"
+#include "ibm-power11-dual.dtsi"
+
+/ {
+	model = "Balcones";
+	compatible = "ibm,balcones-bmc", "aspeed,ast2600";
+
+	aliases {
+		serial4 = &uart5;
+		i2c16 = &i2c11mux0chn0;
+		i2c17 = &i2c11mux0chn1;
+		i2c18 = &i2c11mux0chn2;
+		i2c19 = &i2c11mux0chn3;
+	};
+
+	chosen {
+		stdout-path = &uart5;
+	};
+
+	gpio-keys-polled {
+		compatible = "gpio-keys-polled";
+		poll-interval = <1000>;
+
+		event-fan0-presence {
+			gpios = <&gpio0 ASPEED_GPIO(F, 4) GPIO_ACTIVE_LOW>;
+			label = "fan0-presence";
+			linux,code = <6>;
+		};
+
+		event-fan1-presence {
+			gpios = <&gpio0 ASPEED_GPIO(F, 5) GPIO_ACTIVE_LOW>;
+			label = "fan1-presence";
+			linux,code = <7>;
+		};
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc1 7>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-fan0 {
+			gpios = <&gpio0 ASPEED_GPIO(G, 0) GPIO_ACTIVE_LOW>;
+		};
+
+		led-fan1 {
+			gpios = <&gpio0 ASPEED_GPIO(G, 1) GPIO_ACTIVE_LOW>;
+		};
+
+		led-rear-enc-id0 {
+			gpios = <&gpio0 ASPEED_GPIO(H, 2) GPIO_ACTIVE_LOW>;
+		};
+
+		led-rear-enc-fault0 {
+			gpios = <&gpio0 ASPEED_GPIO(H, 3) GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x40000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		event_log: region@b3d00000 {
+			reg = <0xb3d00000 0x100000>;
+			no-map;
+		};
+
+		ramoops@b3e00000 {
+			compatible = "ramoops";
+			reg = <0xb3e00000 0x200000>; /* 16 * (4 * 0x8000) */
+			record-size = <0x8000>;
+			console-size = <0x8000>;
+			ftrace-size = <0x8000>;
+			pmsg-size = <0x8000>;
+			max-reason = <3>; /* KMSG_DUMP_EMERG */
+		};
+
+		/* LPC FW cycle bridge region requires natural alignment */
+		flash_memory: region@b4000000 {
+			reg = <0xb4000000 0x04000000>; /* 64M */
+			no-map;
+		};
+
+		/* VGA region is dictated by hardware strapping */
+		vga_memory: region@bf000000 {
+			compatible = "shared-dma-pool";
+			reg = <0xbf000000 0x01000000>;  /* 16M */
+			no-map;
+		};
+	};
+};
+
+&adc1 {
+	aspeed,int-vref-microvolt = <2500000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
+		&pinctrl_adc10_default &pinctrl_adc11_default
+		&pinctrl_adc12_default &pinctrl_adc13_default
+		&pinctrl_adc14_default &pinctrl_adc15_default>;
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&emmc {
+	clk-phase-mmc-hs200 = <180>, <180>;
+	status = "okay";
+};
+
+&emmc_controller {
+	status = "okay";
+};
+
+&gpio0 {
+	gpio-line-names =
+		/*A0-A7*/	"","","","","","","","",
+		/*B0-B7*/	"","","","","","","checkstop","",
+		/*C0-C7*/	"","","","","","","","",
+		/*D0-D7*/	"","","","","","","","",
+		/*E0-E7*/	"","","","","","","","",
+		/*F0-F7*/	"","fan-ctlr-reset","rtc-battery-voltage-read-enable",
+				"reset-cause-pinhole","","","","",
+		/*G0-G7*/	"fan0","fan1","","","","","","",
+		/*H0-H7*/	"","","rear-enc-id0","rear-enc-fault0","","","","",
+		/*I0-I7*/	"","","","","","","bmc-secure-boot","",
+		/*J0-J7*/	"","","","","","","","",
+		/*K0-K7*/	"","","","","","","","",
+		/*L0-L7*/	"","","","","","","","",
+		/*M0-M7*/	"","","","","","","","",
+		/*N0-N7*/	"","","","","","","","",
+		/*O0-O7*/	"","","","usb-power","","","","",
+		/*P0-P7*/	"","","","","","","","",
+		/*Q0-Q7*/	"cfam-reset","","regulator-standby-faulted","","","","","",
+		/*R0-R7*/	"bmc-tpm-reset","power-chassis-control","power-chassis-good","","",
+				"","","",
+		/*S0-S7*/	"presence-ps0","presence-ps1","","","power-ffs-sync-history","","",
+				"",
+		/*T0-T7*/	"","","","","","","","",
+		/*U0-U7*/	"","","","","","","","",
+		/*V0-V7*/	"","","","","","","","",
+		/*W0-W7*/	"","","","","","","","",
+		/*X0-X7*/	"","","","","","","","",
+		/*Y0-Y7*/	"","","","","","","","",
+		/*Z0-Z7*/	"","","","","","","","";
+
+	usb-power-hog {
+		gpio-hog;
+		gpios = <ASPEED_GPIO(O, 3) GPIO_ACTIVE_LOW>;
+		output-high;
+	};
+};
+
+&i2c0 {
+	status = "okay";
+
+	gpio@20 {
+		compatible = "ti,tca9554";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+			"",
+			"RUSSEL_FW_I2C_ENABLE_N",
+			"RUSSEL_OPPANEL_PRESENCE_N",
+			"BLYTH_OPPANEL_PRESENCE_N",
+			"CPU_TPM_CARD_PRESENT_N",
+			"",
+			"",
+			"DASD_BP_PRESENT_N";
+	};
+
+	eeprom@51 {
+		compatible = "atmel,24c64";
+		reg = <0x51>;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+
+	pmic@64 {
+		compatible = "ti,ucd90160";
+		reg = <0x64>;
+	};
+};
+
+&i2c3 {
+	status = "okay";
+
+	power-supply@5a {
+		compatible = "acbel,fsg032";
+		reg = <0x5a>;
+	};
+
+	power-supply@5b {
+		compatible = "acbel,fsg032";
+		reg = <0x5b>;
+	};
+};
+
+&i2c4 {
+	status = "okay";
+};
+
+&i2c5 {
+	status = "okay";
+
+	eeprom@52 {
+		compatible = "atmel,24c64";
+		reg = <0x52>;
+	};
+
+	led-controller@62 {
+		compatible = "nxp,pca9551";
+		reg = <0x62>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			reg = <0>;
+			default-state = "keep";
+			label = "cablecard2-cxp-top";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			reg = <1>;
+			default-state = "keep";
+			label = "cablecard2-cxp-bot";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+};
+
+&i2c6 {
+	status = "okay";
+};
+
+&i2c7 {
+	multi-master;
+	status = "okay";
+
+	temperature-sensor@48 {
+		compatible = "ti,tmp275";
+		reg = <0x48>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+
+	eeprom@51 {
+		compatible = "atmel,24c64";
+		reg = <0x51>;
+	};
+
+	pwm@53 {
+		compatible = "maxim,max31785a";
+		reg = <0x53>;
+	};
+
+	led-controller@60 {
+		compatible = "nxp,pca9551";
+		reg = <0x60>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			reg = <0>;
+			default-state = "keep";
+			label = "front-sys-id0";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			reg = <1>;
+			default-state = "keep";
+			label = "front-check-log0";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			reg = <2>;
+			default-state = "keep";
+			label = "front-enc-fault1";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			reg = <3>;
+			default-state = "keep";
+			label = "front-sys-pwron0";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	lcd-controller@62 {
+		compatible = "ibm,op-panel";
+		reg = <(0x62 | I2C_OWN_SLAVE_ADDRESS)>;
+	};
+
+	pressure-sensor@76 {
+		compatible = "infineon,dps310";
+		reg = <0x76>;
+		#io-channel-cells = <0>;
+	};
+};
+
+&i2c8 {
+	status = "okay";
+
+	rtc@32 {
+		compatible = "epson,rx8900";
+		reg = <0x32>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c128";
+		reg = <0x50>;
+	};
+
+	led-controller@60 {
+		compatible = "nxp,pca9551";
+		reg = <0x60>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+			"",
+			"APSS_RESET_N",
+			"",
+			"N_MODE_CPU_N",
+			"",
+			"",
+			"P10_DCM_PRESENT",
+			"";
+	};
+
+	led-controller@61 {
+		compatible = "nxp,pca9552";
+		reg = <0x61>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+			"",
+			"",
+			"SLOT2_PRSNT_EN_RSVD",
+			"",
+			"",
+			"",
+			"",
+			"SLOT2_EXPANDER_PRSNT_N",
+			"",
+			"",
+			"",
+			"",
+			"",
+			"",
+			"",
+			"";
+	};
+};
+
+&i2c9 {
+	status = "okay";
+
+	temperature-sensor@4c {
+		compatible = "ti,tmp423";
+		reg = <0x4c>;
+	};
+};
+
+&i2c10 {
+	status = "okay";
+};
+
+&i2c11 {
+	status = "okay";
+
+	gpio@20 {
+		compatible = "ti,tca9554";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+			"BOOT_RCVRY_TWI",
+			"BOOT_RCVRY_UART",
+			"",
+			"",
+			"",
+			"",
+			"",
+			"PE_SWITCH_RSTB_N";
+	};
+
+	temperature-sensor@4c {
+		compatible = "ti,tmp435";
+		reg = <0x4c>;
+	};
+
+	i2c-mux@75 {
+		compatible = "nxp,pca9849";
+		reg = <0x75>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c11mux0chn0: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c11mux0chn1: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c11mux0chn2: i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c11mux0chn3: i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+&i2c12 {
+	status = "okay";
+
+	tpm@2e {
+		compatible = "nuvoton,npct75x", "tcg,tpm-tis-i2c";
+		reg = <0x2e>;
+		memory-region = <&event_log>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+};
+
+&i2c13 {
+	status = "okay";
+
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+
+	led-controller@60 {
+		compatible = "nxp,pca9551";
+		reg = <0x60>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			reg = <0>;
+			default-state = "keep";
+			label = "nvme3";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			reg = <1>;
+			default-state = "keep";
+			label = "nvme2";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			reg = <2>;
+			default-state = "keep";
+			label = "nvme1";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			reg = <3>;
+			default-state = "keep";
+			label = "nvme0";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+};
+
+&i2c14 {
+	status = "okay";
+};
+
+&i2c15 {
+	status = "okay";
+};
+
+&ibt {
+	status = "okay";
+};
+
+&kcs2 {
+	aspeed,lpc-io-reg = <0xca8 0xcac>;
+	status = "okay";
+};
+
+&kcs3 {
+	aspeed,lpc-io-reg = <0xca2>;
+	aspeed,lpc-interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+	status = "okay";
+};
+
+&lpc_ctrl {
+	memory-region = <&flash_memory>;
+	status = "okay";
+};
+
+&mac2 {
+	clocks = <&syscon ASPEED_CLK_GATE_MAC3CLK>,
+		 <&syscon ASPEED_CLK_MAC3RCLK>;
+	clock-names = "MACCLK", "RCLK";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii3_default>;
+	use-ncsi;
+	status = "okay";
+};
+
+&pinctrl_emmc_default {
+	bias-disable;
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uhci {
+	status = "okay";
+};
+
+&vuart1 {
+	status = "okay";
+};
+
+&vuart2 {
+	status = "okay";
+};
+
+&wdt1 {
+	aspeed,reset-type = "none";
+	aspeed,external-signal;
+	aspeed,ext-push-pull;
+	aspeed,ext-active-high;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdtrst1_default>;
+};
+
+&wdt2 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/aspeed/ibm-power11-dual.dtsi b/arch/arm/boot/dts/aspeed/ibm-power11-dual.dtsi
new file mode 100644
index 0000000000000..6db02d4753800
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/ibm-power11-dual.dtsi
@@ -0,0 +1,779 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright 2025 IBM Corp.
+
+/ {
+	aliases {
+		i2c100 = &cfam0_i2c0;
+		i2c101 = &cfam0_i2c1;
+		i2c110 = &cfam0_i2c10;
+		i2c111 = &cfam0_i2c11;
+		i2c112 = &cfam0_i2c12;
+		i2c113 = &cfam0_i2c13;
+		i2c114 = &cfam0_i2c14;
+		i2c115 = &cfam0_i2c15;
+		i2c202 = &cfam1_i2c2;
+		i2c203 = &cfam1_i2c3;
+		i2c210 = &cfam1_i2c10;
+		i2c211 = &cfam1_i2c11;
+		i2c214 = &cfam1_i2c14;
+		i2c215 = &cfam1_i2c15;
+		i2c216 = &cfam1_i2c16;
+		i2c217 = &cfam1_i2c17;
+
+		sbefifo100 = &sbefifo100;
+		sbefifo101 = &sbefifo101;
+		sbefifo110 = &sbefifo110;
+		sbefifo111 = &sbefifo111;
+		sbefifo112 = &sbefifo112;
+		sbefifo113 = &sbefifo113;
+		sbefifo114 = &sbefifo114;
+		sbefifo115 = &sbefifo115;
+		sbefifo202 = &sbefifo202;
+		sbefifo203 = &sbefifo203;
+		sbefifo210 = &sbefifo210;
+		sbefifo211 = &sbefifo211;
+		sbefifo214 = &sbefifo214;
+		sbefifo215 = &sbefifo215;
+		sbefifo216 = &sbefifo216;
+		sbefifo217 = &sbefifo217;
+
+		scom100 = &scom100;
+		scom101 = &scom101;
+		scom110 = &scom110;
+		scom111 = &scom111;
+		scom112 = &scom112;
+		scom113 = &scom113;
+		scom114 = &scom114;
+		scom115 = &scom115;
+		scom202 = &scom202;
+		scom203 = &scom203;
+		scom210 = &scom210;
+		scom211 = &scom211;
+		scom214 = &scom214;
+		scom215 = &scom215;
+		scom216 = &scom216;
+		scom217 = &scom217;
+
+		spi10 = &cfam0_spi0;
+		spi11 = &cfam0_spi1;
+		spi12 = &cfam0_spi2;
+		spi13 = &cfam0_spi3;
+		spi20 = &cfam1_spi0;
+		spi21 = &cfam1_spi1;
+		spi22 = &cfam1_spi2;
+		spi23 = &cfam1_spi3;
+	};
+};
+
+&fsim0 {
+	bus-frequency = <100000000>;
+	#address-cells = <2>;
+	#size-cells = <0>;
+	cfam-reset-gpios = <&gpio0 ASPEED_GPIO(Q, 0) GPIO_ACTIVE_HIGH>;
+	status = "okay";
+
+	cfam@0,0 {
+		reg = <0 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		chip-id = <0>;
+
+		scom@1000 {
+			compatible = "ibm,p9-scom";
+			reg = <0x1000 0x400>;
+		};
+
+		i2c@1800 {
+			compatible = "ibm,i2c-fsi";
+			reg = <0x1800 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam0_i2c0: i2c-bus@0 {
+				reg = <0>;	/* OMI01 */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom100: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo100: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam0_i2c1: i2c-bus@1 {
+				reg = <1>;	/* OMI23 */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom101: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo101: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam0_i2c10: i2c-bus@a {
+				reg = <10>;	/* OP3A */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom110: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo110: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam0_i2c11: i2c-bus@b {
+				reg = <11>;	/* OP3B */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom111: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo111: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam0_i2c12: i2c-bus@c {
+				reg = <12>;	/* OP4A */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom112: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo112: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam0_i2c13: i2c-bus@d {
+				reg = <13>;	/* OP4B */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom113: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo113: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam0_i2c14: i2c-bus@e {
+				reg = <14>;	/* OP5A */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom114: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo114: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam0_i2c15: i2c-bus@f {
+				reg = <15>;	/* OP5B */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom115: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo115: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+		};
+
+		fsi2spi@1c00 {
+			compatible = "ibm,fsi2spi";
+			reg = <0x1c00 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam0_spi0: spi@0 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					address-width = <24>;
+					pagesize = <256>;
+					size = <0x80000>;
+					spi-max-frequency = <10000000>;
+				};
+			};
+
+			cfam0_spi1: spi@20 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					address-width = <24>;
+					pagesize = <256>;
+					size = <0x80000>;
+					spi-max-frequency = <10000000>;
+				};
+			};
+
+			cfam0_spi2: spi@40 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x40>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					address-width = <24>;
+					pagesize = <256>;
+					size = <0x80000>;
+					spi-max-frequency = <10000000>;
+				};
+			};
+
+			cfam0_spi3: spi@60 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					address-width = <24>;
+					pagesize = <256>;
+					size = <0x80000>;
+					spi-max-frequency = <10000000>;
+				};
+			};
+		};
+
+		sbefifo@2400 {
+			compatible = "ibm,p9-sbefifo";
+			reg = <0x2400 0x400>;
+
+			occ {
+				compatible = "ibm,p10-occ";
+
+				hwmon {
+					compatible = "ibm,p10-occ-hwmon";
+					ibm,no-poll-on-init;
+				};
+			};
+		};
+
+		fsi_hub0: fsi@3400 {
+			compatible = "ibm,p9-fsi-controller";
+			reg = <0x3400 0x400>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+&fsi_hub0 {
+	cfam@1,0 {
+		reg = <1 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		chip-id = <1>;
+
+		scom@1000 {
+			compatible = "ibm,p9-scom";
+			reg = <0x1000 0x400>;
+		};
+
+		i2c@1800 {
+			compatible = "ibm,i2c-fsi";
+			reg = <0x1800 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam1_i2c2: i2c-bus@2 {
+				reg = <2>;	/* OMI45 */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom202: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo202: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam1_i2c3: i2c-bus@3 {
+				reg = <3>;	/* OMI67 */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom203: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo203: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam1_i2c10: i2c-bus@a {
+				reg = <10>;	/* OP3A */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom210: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo210: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam1_i2c11: i2c-bus@b {
+				reg = <11>;	/* OP3B */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom211: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo211: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam1_i2c14: i2c-bus@e {
+				reg = <14>;	/* OP5A */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom214: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo214: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam1_i2c15: i2c-bus@f {
+				reg = <15>;	/* OP5B */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom215: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo215: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam1_i2c16: i2c-bus@10 {
+				reg = <16>;	/* OP6A */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom216: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo216: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam1_i2c17: i2c-bus@11 {
+				reg = <17>;	/* OP6B */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom217: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo217: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+		};
+
+		fsi2spi@1c00 {
+			compatible = "ibm,fsi2spi";
+			reg = <0x1c00 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam1_spi0: spi@0 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					address-width = <24>;
+					pagesize = <256>;
+					size = <0x80000>;
+					spi-max-frequency = <10000000>;
+				};
+			};
+
+			cfam1_spi1: spi@20 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					address-width = <24>;
+					pagesize = <256>;
+					size = <0x80000>;
+					spi-max-frequency = <10000000>;
+				};
+			};
+
+			cfam1_spi2: spi@40 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x40>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					address-width = <24>;
+					pagesize = <256>;
+					size = <0x80000>;
+					spi-max-frequency = <10000000>;
+				};
+			};
+
+			cfam1_spi3: spi@60 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					address-width = <24>;
+					pagesize = <256>;
+					size = <0x80000>;
+					spi-max-frequency = <10000000>;
+				};
+			};
+		};
+
+		sbefifo@2400 {
+			compatible = "ibm,p9-sbefifo";
+			reg = <0x2400 0x400>;
+
+			occ {
+				compatible = "ibm,p10-occ";
+
+				hwmon {
+					compatible = "ibm,p10-occ-hwmon";
+					ibm,no-poll-on-init;
+				};
+			};
+		};
+
+		fsi@3400 {
+			compatible = "ibm,p9-fsi-controller";
+			reg = <0x3400 0x400>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+			no-scan-on-init;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/aspeed/ibm-power11-quad.dtsi b/arch/arm/boot/dts/aspeed/ibm-power11-quad.dtsi
index 68c941a194b64..7aa4113d30263 100644
--- a/arch/arm/boot/dts/aspeed/ibm-power11-quad.dtsi
+++ b/arch/arm/boot/dts/aspeed/ibm-power11-quad.dtsi
@@ -1,24 +1,10 @@
 // SPDX-License-Identifier: GPL-2.0-or-later
 // Copyright 2024 IBM Corp.
 
+#include "ibm-power11-dual.dtsi"
+
 / {
 	aliases {
-		i2c100 = &cfam0_i2c0;
-		i2c101 = &cfam0_i2c1;
-		i2c110 = &cfam0_i2c10;
-		i2c111 = &cfam0_i2c11;
-		i2c112 = &cfam0_i2c12;
-		i2c113 = &cfam0_i2c13;
-		i2c114 = &cfam0_i2c14;
-		i2c115 = &cfam0_i2c15;
-		i2c202 = &cfam1_i2c2;
-		i2c203 = &cfam1_i2c3;
-		i2c210 = &cfam1_i2c10;
-		i2c211 = &cfam1_i2c11;
-		i2c214 = &cfam1_i2c14;
-		i2c215 = &cfam1_i2c15;
-		i2c216 = &cfam1_i2c16;
-		i2c217 = &cfam1_i2c17;
 		i2c300 = &cfam2_i2c0;
 		i2c301 = &cfam2_i2c1;
 		i2c310 = &cfam2_i2c10;
@@ -36,22 +22,6 @@ aliases {
 		i2c416 = &cfam3_i2c16;
 		i2c417 = &cfam3_i2c17;
 
-		sbefifo100 = &sbefifo100;
-		sbefifo101 = &sbefifo101;
-		sbefifo110 = &sbefifo110;
-		sbefifo111 = &sbefifo111;
-		sbefifo112 = &sbefifo112;
-		sbefifo113 = &sbefifo113;
-		sbefifo114 = &sbefifo114;
-		sbefifo115 = &sbefifo115;
-		sbefifo202 = &sbefifo202;
-		sbefifo203 = &sbefifo203;
-		sbefifo210 = &sbefifo210;
-		sbefifo211 = &sbefifo211;
-		sbefifo214 = &sbefifo214;
-		sbefifo215 = &sbefifo215;
-		sbefifo216 = &sbefifo216;
-		sbefifo217 = &sbefifo217;
 		sbefifo300 = &sbefifo300;
 		sbefifo301 = &sbefifo301;
 		sbefifo310 = &sbefifo310;
@@ -69,22 +39,6 @@ aliases {
 		sbefifo416 = &sbefifo416;
 		sbefifo417 = &sbefifo417;
 
-		scom100 = &scom100;
-		scom101 = &scom101;
-		scom110 = &scom110;
-		scom111 = &scom111;
-		scom112 = &scom112;
-		scom113 = &scom113;
-		scom114 = &scom114;
-		scom115 = &scom115;
-		scom202 = &scom202;
-		scom203 = &scom203;
-		scom210 = &scom210;
-		scom211 = &scom211;
-		scom214 = &scom214;
-		scom215 = &scom215;
-		scom216 = &scom216;
-		scom217 = &scom217;
 		scom300 = &scom300;
 		scom301 = &scom301;
 		scom310 = &scom310;
@@ -102,14 +56,6 @@ aliases {
 		scom416 = &scom416;
 		scom417 = &scom417;
 
-		spi10 = &cfam0_spi0;
-		spi11 = &cfam0_spi1;
-		spi12 = &cfam0_spi2;
-		spi13 = &cfam0_spi3;
-		spi20 = &cfam1_spi0;
-		spi21 = &cfam1_spi1;
-		spi22 = &cfam1_spi2;
-		spi23 = &cfam1_spi3;
 		spi30 = &cfam2_spi0;
 		spi31 = &cfam2_spi1;
 		spi32 = &cfam2_spi2;
@@ -121,718 +67,7 @@ aliases {
 	};
 };
 
-&fsim0 {
-	#address-cells = <2>;
-	#size-cells = <0>;
-	status = "okay";
-	bus-frequency = <100000000>;
-	cfam-reset-gpios = <&gpio0 ASPEED_GPIO(Q, 0) GPIO_ACTIVE_HIGH>;
-
-	cfam@0,0 {
-		reg = <0 0>;
-		#address-cells = <1>;
-		#size-cells = <1>;
-		chip-id = <0>;
-
-		scom@1000 {
-			compatible = "ibm,p9-scom";
-			reg = <0x1000 0x400>;
-		};
-
-		i2c@1800 {
-			compatible = "ibm,i2c-fsi";
-			reg = <0x1800 0x400>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			cfam0_i2c0: i2c-bus@0 {
-				reg = <0>;	/* OMI01 */
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				fsi@20 {
-					compatible = "ibm,i2cr-fsi-master";
-					reg = <0x20>;
-					#address-cells = <2>;
-					#size-cells = <0>;
-
-					cfam@0,0 {
-						reg = <0 0>;
-						#address-cells = <1>;
-						#size-cells = <1>;
-						chip-id = <0>;
-
-						scom100: scom@1000 {
-							compatible = "ibm,i2cr-scom";
-							reg = <0x1000 0x400>;
-						};
-
-						sbefifo100: sbefifo@2400 {
-							compatible = "ibm,odyssey-sbefifo";
-							reg = <0x2400 0x400>;
-						};
-					};
-				};
-			};
-
-			cfam0_i2c1: i2c-bus@1 {
-				reg = <1>;	/* OMI23 */
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				fsi@20 {
-					compatible = "ibm,i2cr-fsi-master";
-					reg = <0x20>;
-					#address-cells = <2>;
-					#size-cells = <0>;
-
-					cfam@0,0 {
-						reg = <0 0>;
-						#address-cells = <1>;
-						#size-cells = <1>;
-						chip-id = <0>;
-
-						scom101: scom@1000 {
-							compatible = "ibm,i2cr-scom";
-							reg = <0x1000 0x400>;
-						};
-
-						sbefifo101: sbefifo@2400 {
-							compatible = "ibm,odyssey-sbefifo";
-							reg = <0x2400 0x400>;
-						};
-					};
-				};
-			};
-
-			cfam0_i2c10: i2c-bus@a {
-				reg = <10>;	/* OP3A */
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				fsi@20 {
-					compatible = "ibm,i2cr-fsi-master";
-					reg = <0x20>;
-					#address-cells = <2>;
-					#size-cells = <0>;
-
-					cfam@0,0 {
-						reg = <0 0>;
-						#address-cells = <1>;
-						#size-cells = <1>;
-						chip-id = <0>;
-
-						scom110: scom@1000 {
-							compatible = "ibm,i2cr-scom";
-							reg = <0x1000 0x400>;
-						};
-
-						sbefifo110: sbefifo@2400 {
-							compatible = "ibm,odyssey-sbefifo";
-							reg = <0x2400 0x400>;
-						};
-					};
-				};
-			};
-
-			cfam0_i2c11: i2c-bus@b {
-				reg = <11>;	/* OP3B */
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				fsi@20 {
-					compatible = "ibm,i2cr-fsi-master";
-					reg = <0x20>;
-					#address-cells = <2>;
-					#size-cells = <0>;
-
-					cfam@0,0 {
-						reg = <0 0>;
-						#address-cells = <1>;
-						#size-cells = <1>;
-						chip-id = <0>;
-
-						scom111: scom@1000 {
-							compatible = "ibm,i2cr-scom";
-							reg = <0x1000 0x400>;
-						};
-
-						sbefifo111: sbefifo@2400 {
-							compatible = "ibm,odyssey-sbefifo";
-							reg = <0x2400 0x400>;
-						};
-					};
-				};
-			};
-
-			cfam0_i2c12: i2c-bus@c {
-				reg = <12>;	/* OP4A */
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				fsi@20 {
-					compatible = "ibm,i2cr-fsi-master";
-					reg = <0x20>;
-					#address-cells = <2>;
-					#size-cells = <0>;
-
-					cfam@0,0 {
-						reg = <0 0>;
-						#address-cells = <1>;
-						#size-cells = <1>;
-						chip-id = <0>;
-
-						scom112: scom@1000 {
-							compatible = "ibm,i2cr-scom";
-							reg = <0x1000 0x400>;
-						};
-
-						sbefifo112: sbefifo@2400 {
-							compatible = "ibm,odyssey-sbefifo";
-							reg = <0x2400 0x400>;
-						};
-					};
-				};
-			};
-
-			cfam0_i2c13: i2c-bus@d {
-				reg = <13>;	/* OP4B */
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				fsi@20 {
-					compatible = "ibm,i2cr-fsi-master";
-					reg = <0x20>;
-					#address-cells = <2>;
-					#size-cells = <0>;
-
-					cfam@0,0 {
-						reg = <0 0>;
-						#address-cells = <1>;
-						#size-cells = <1>;
-						chip-id = <0>;
-
-						scom113: scom@1000 {
-							compatible = "ibm,i2cr-scom";
-							reg = <0x1000 0x400>;
-						};
-
-						sbefifo113: sbefifo@2400 {
-							compatible = "ibm,odyssey-sbefifo";
-							reg = <0x2400 0x400>;
-						};
-					};
-				};
-			};
-
-			cfam0_i2c14: i2c-bus@e {
-				reg = <14>;	/* OP5A */
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				fsi@20 {
-					compatible = "ibm,i2cr-fsi-master";
-					reg = <0x20>;
-					#address-cells = <2>;
-					#size-cells = <0>;
-
-					cfam@0,0 {
-						reg = <0 0>;
-						#address-cells = <1>;
-						#size-cells = <1>;
-						chip-id = <0>;
-
-						scom114: scom@1000 {
-							compatible = "ibm,i2cr-scom";
-							reg = <0x1000 0x400>;
-						};
-
-						sbefifo114: sbefifo@2400 {
-							compatible = "ibm,odyssey-sbefifo";
-							reg = <0x2400 0x400>;
-						};
-					};
-				};
-			};
-
-			cfam0_i2c15: i2c-bus@f {
-				reg = <15>;	/* OP5B */
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				fsi@20 {
-					compatible = "ibm,i2cr-fsi-master";
-					reg = <0x20>;
-					#address-cells = <2>;
-					#size-cells = <0>;
-
-					cfam@0,0 {
-						reg = <0 0>;
-						#address-cells = <1>;
-						#size-cells = <1>;
-						chip-id = <0>;
-
-						scom115: scom@1000 {
-							compatible = "ibm,i2cr-scom";
-							reg = <0x1000 0x400>;
-						};
-
-						sbefifo115: sbefifo@2400 {
-							compatible = "ibm,odyssey-sbefifo";
-							reg = <0x2400 0x400>;
-						};
-					};
-				};
-			};
-		};
-
-		fsi2spi@1c00 {
-			compatible = "ibm,fsi2spi";
-			reg = <0x1c00 0x400>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			cfam0_spi0: spi@0 {
-				compatible = "ibm,spi-fsi";
-				reg = <0x0>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				eeprom@0 {
-					compatible = "atmel,at25";
-					reg = <0>;
-					address-width = <24>;
-					pagesize = <256>;
-					size = <0x80000>;
-					spi-max-frequency = <10000000>;
-				};
-			};
-
-			cfam0_spi1: spi@20 {
-				compatible = "ibm,spi-fsi";
-				reg = <0x20>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				eeprom@0 {
-					compatible = "atmel,at25";
-					reg = <0>;
-					address-width = <24>;
-					pagesize = <256>;
-					size = <0x80000>;
-					spi-max-frequency = <10000000>;
-				};
-			};
-
-			cfam0_spi2: spi@40 {
-				compatible = "ibm,spi-fsi";
-				reg = <0x40>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				eeprom@0 {
-					compatible = "atmel,at25";
-					reg = <0>;
-					address-width = <24>;
-					pagesize = <256>;
-					size = <0x80000>;
-					spi-max-frequency = <10000000>;
-				};
-			};
-
-			cfam0_spi3: spi@60 {
-				compatible = "ibm,spi-fsi";
-				reg = <0x60>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				eeprom@0 {
-					compatible = "atmel,at25";
-					reg = <0>;
-					address-width = <24>;
-					pagesize = <256>;
-					size = <0x80000>;
-					spi-max-frequency = <10000000>;
-				};
-			};
-		};
-
-		sbefifo@2400 {
-			compatible = "ibm,p9-sbefifo";
-			reg = <0x2400 0x400>;
-
-			occ {
-				compatible = "ibm,p10-occ";
-
-				hwmon {
-					compatible = "ibm,p10-occ-hwmon";
-					ibm,no-poll-on-init;
-				};
-			};
-		};
-
-		fsi_hub0: fsi@3400 {
-			compatible = "ibm,p9-fsi-controller";
-			reg = <0x3400 0x400>;
-			#address-cells = <2>;
-			#size-cells = <0>;
-		};
-	};
-};
-
 &fsi_hub0 {
-	cfam@1,0 {
-		reg = <1 0>;
-		#address-cells = <1>;
-		#size-cells = <1>;
-		chip-id = <1>;
-
-		scom@1000 {
-			compatible = "ibm,p9-scom";
-			reg = <0x1000 0x400>;
-		};
-
-		i2c@1800 {
-			compatible = "ibm,i2c-fsi";
-			reg = <0x1800 0x400>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			cfam1_i2c2: i2c-bus@2 {
-				reg = <2>;	/* OMI45 */
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				fsi@20 {
-					compatible = "ibm,i2cr-fsi-master";
-					reg = <0x20>;
-					#address-cells = <2>;
-					#size-cells = <0>;
-
-					cfam@0,0 {
-						reg = <0 0>;
-						#address-cells = <1>;
-						#size-cells = <1>;
-						chip-id = <0>;
-
-						scom202: scom@1000 {
-							compatible = "ibm,i2cr-scom";
-							reg = <0x1000 0x400>;
-						};
-
-						sbefifo202: sbefifo@2400 {
-							compatible = "ibm,odyssey-sbefifo";
-							reg = <0x2400 0x400>;
-						};
-					};
-				};
-			};
-
-			cfam1_i2c3: i2c-bus@3 {
-				reg = <3>;	/* OMI67 */
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				fsi@20 {
-					compatible = "ibm,i2cr-fsi-master";
-					reg = <0x20>;
-					#address-cells = <2>;
-					#size-cells = <0>;
-
-					cfam@0,0 {
-						reg = <0 0>;
-						#address-cells = <1>;
-						#size-cells = <1>;
-						chip-id = <0>;
-
-						scom203: scom@1000 {
-							compatible = "ibm,i2cr-scom";
-							reg = <0x1000 0x400>;
-						};
-
-						sbefifo203: sbefifo@2400 {
-							compatible = "ibm,odyssey-sbefifo";
-							reg = <0x2400 0x400>;
-						};
-					};
-				};
-			};
-
-			cfam1_i2c10: i2c-bus@a {
-				reg = <10>;	/* OP3A */
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				fsi@20 {
-					compatible = "ibm,i2cr-fsi-master";
-					reg = <0x20>;
-					#address-cells = <2>;
-					#size-cells = <0>;
-
-					cfam@0,0 {
-						reg = <0 0>;
-						#address-cells = <1>;
-						#size-cells = <1>;
-						chip-id = <0>;
-
-						scom210: scom@1000 {
-							compatible = "ibm,i2cr-scom";
-							reg = <0x1000 0x400>;
-						};
-
-						sbefifo210: sbefifo@2400 {
-							compatible = "ibm,odyssey-sbefifo";
-							reg = <0x2400 0x400>;
-						};
-					};
-				};
-			};
-
-			cfam1_i2c11: i2c-bus@b {
-				reg = <11>;	/* OP3B */
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				fsi@20 {
-					compatible = "ibm,i2cr-fsi-master";
-					reg = <0x20>;
-					#address-cells = <2>;
-					#size-cells = <0>;
-
-					cfam@0,0 {
-						reg = <0 0>;
-						#address-cells = <1>;
-						#size-cells = <1>;
-						chip-id = <0>;
-
-						scom211: scom@1000 {
-							compatible = "ibm,i2cr-scom";
-							reg = <0x1000 0x400>;
-						};
-
-						sbefifo211: sbefifo@2400 {
-							compatible = "ibm,odyssey-sbefifo";
-							reg = <0x2400 0x400>;
-						};
-					};
-				};
-			};
-
-			cfam1_i2c14: i2c-bus@e {
-				reg = <14>;	/* OP5A */
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				fsi@20 {
-					compatible = "ibm,i2cr-fsi-master";
-					reg = <0x20>;
-					#address-cells = <2>;
-					#size-cells = <0>;
-
-					cfam@0,0 {
-						reg = <0 0>;
-						#address-cells = <1>;
-						#size-cells = <1>;
-						chip-id = <0>;
-
-						scom214: scom@1000 {
-							compatible = "ibm,i2cr-scom";
-							reg = <0x1000 0x400>;
-						};
-
-						sbefifo214: sbefifo@2400 {
-							compatible = "ibm,odyssey-sbefifo";
-							reg = <0x2400 0x400>;
-						};
-					};
-				};
-			};
-
-			cfam1_i2c15: i2c-bus@f {
-				reg = <15>;	/* OP5B */
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				fsi@20 {
-					compatible = "ibm,i2cr-fsi-master";
-					reg = <0x20>;
-					#address-cells = <2>;
-					#size-cells = <0>;
-
-					cfam@0,0 {
-						reg = <0 0>;
-						#address-cells = <1>;
-						#size-cells = <1>;
-						chip-id = <0>;
-
-						scom215: scom@1000 {
-							compatible = "ibm,i2cr-scom";
-							reg = <0x1000 0x400>;
-						};
-
-						sbefifo215: sbefifo@2400 {
-							compatible = "ibm,odyssey-sbefifo";
-							reg = <0x2400 0x400>;
-						};
-					};
-				};
-			};
-
-			cfam1_i2c16: i2c-bus@10 {
-				reg = <16>;	/* OP6A */
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				fsi@20 {
-					compatible = "ibm,i2cr-fsi-master";
-					reg = <0x20>;
-					#address-cells = <2>;
-					#size-cells = <0>;
-
-					cfam@0,0 {
-						reg = <0 0>;
-						#address-cells = <1>;
-						#size-cells = <1>;
-						chip-id = <0>;
-
-						scom216: scom@1000 {
-							compatible = "ibm,i2cr-scom";
-							reg = <0x1000 0x400>;
-						};
-
-						sbefifo216: sbefifo@2400 {
-							compatible = "ibm,odyssey-sbefifo";
-							reg = <0x2400 0x400>;
-						};
-					};
-				};
-			};
-
-			cfam1_i2c17: i2c-bus@11 {
-				reg = <17>;	/* OP6B */
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				fsi@20 {
-					compatible = "ibm,i2cr-fsi-master";
-					reg = <0x20>;
-					#address-cells = <2>;
-					#size-cells = <0>;
-
-					cfam@0,0 {
-						reg = <0 0>;
-						#address-cells = <1>;
-						#size-cells = <1>;
-						chip-id = <0>;
-
-						scom217: scom@1000 {
-							compatible = "ibm,i2cr-scom";
-							reg = <0x1000 0x400>;
-						};
-
-						sbefifo217: sbefifo@2400 {
-							compatible = "ibm,odyssey-sbefifo";
-							reg = <0x2400 0x400>;
-						};
-					};
-				};
-			};
-		};
-
-		fsi2spi@1c00 {
-			compatible = "ibm,fsi2spi";
-			reg = <0x1c00 0x400>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			cfam1_spi0: spi@0 {
-				compatible = "ibm,spi-fsi";
-				reg = <0x0>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				eeprom@0 {
-					compatible = "atmel,at25";
-					reg = <0>;
-					address-width = <24>;
-					pagesize = <256>;
-					size = <0x80000>;
-					spi-max-frequency = <10000000>;
-				};
-			};
-
-			cfam1_spi1: spi@20 {
-				compatible = "ibm,spi-fsi";
-				reg = <0x20>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				eeprom@0 {
-					compatible = "atmel,at25";
-					reg = <0>;
-					address-width = <24>;
-					pagesize = <256>;
-					size = <0x80000>;
-					spi-max-frequency = <10000000>;
-				};
-			};
-
-			cfam1_spi2: spi@40 {
-				compatible = "ibm,spi-fsi";
-				reg = <0x40>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				eeprom@0 {
-					compatible = "atmel,at25";
-					reg = <0>;
-					address-width = <24>;
-					pagesize = <256>;
-					size = <0x80000>;
-					spi-max-frequency = <10000000>;
-				};
-			};
-
-			cfam1_spi3: spi@60 {
-				compatible = "ibm,spi-fsi";
-				reg = <0x60>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				eeprom@0 {
-					compatible = "atmel,at25";
-					reg = <0>;
-					address-width = <24>;
-					pagesize = <256>;
-					size = <0x80000>;
-					spi-max-frequency = <10000000>;
-				};
-			};
-		};
-
-		sbefifo@2400 {
-			compatible = "ibm,p9-sbefifo";
-			reg = <0x2400 0x400>;
-
-			occ {
-				compatible = "ibm,p10-occ";
-
-				hwmon {
-					compatible = "ibm,p10-occ-hwmon";
-					ibm,no-poll-on-init;
-				};
-			};
-		};
-
-		fsi@3400 {
-			compatible = "ibm,p9-fsi-controller";
-			reg = <0x3400 0x400>;
-			#address-cells = <2>;
-			#size-cells = <0>;
-			no-scan-on-init;
-		};
-	};
-
 	cfam@2,0 {
 		reg = <2 0>;
 		#address-cells = <1>;
-- 
2.51.0

[PATCH v7 RESEND 7/7] ARM: dts: aspeed: Fix max31785 fan properties

[Eddie James]

Remove non-existant fan properties from max31785 nodes.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
---
 .../dts/aspeed/aspeed-bmc-ibm-bonnell.dts     |  4 ---
 .../dts/aspeed/aspeed-bmc-ibm-everest.dts     |  8 -----
 .../dts/aspeed/aspeed-bmc-ibm-rainier.dts     | 12 -------
 .../boot/dts/aspeed/aspeed-bmc-opp-tacoma.dts | 36 -------------------
 4 files changed, 60 deletions(-)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-bonnell.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-bonnell.dts
index 2f5d4075a64ad..a37399ff3cea2 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-bonnell.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-bonnell.dts
@@ -277,15 +277,11 @@ max31785@52 {
 		#size-cells = <0>;
 
 		fan0: fan@0 {
-			compatible = "pmbus-fan";
 			reg = <0>;
-			tach-pulses = <2>;
 		};
 
 		fan1: fan@1 {
-			compatible = "pmbus-fan";
 			reg = <1>;
-			tach-pulses = <2>;
 		};
 	};
 
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-everest.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-everest.dts
index 9f144f527f03b..5a0975d52492c 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-everest.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-everest.dts
@@ -2066,27 +2066,19 @@ max31785@52 {
 				reg = <0x52>;
 
 				fan@0 {
-					compatible = "pmbus-fan";
 					reg = <0>;
-					tach-pulses = <2>;
 				};
 
 				fan@1 {
-					compatible = "pmbus-fan";
 					reg = <1>;
-					tach-pulses = <2>;
 				};
 
 				fan@2 {
-					compatible = "pmbus-fan";
 					reg = <2>;
-					tach-pulses = <2>;
 				};
 
 				fan@3 {
-					compatible = "pmbus-fan";
 					reg = <3>;
-					tach-pulses = <2>;
 				};
 			};
 
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-rainier.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-rainier.dts
index c5fb5d410001b..e90421bf7e3af 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-rainier.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-rainier.dts
@@ -1080,39 +1080,27 @@ max: max31785@52 {
 		#size-cells = <0>;
 
 		fan0: fan@0 {
-			compatible = "pmbus-fan";
 			reg = <0>;
-			tach-pulses = <2>;
 		};
 
 		fan1: fan@1 {
-			compatible = "pmbus-fan";
 			reg = <1>;
-			tach-pulses = <2>;
 		};
 
 		fan2: fan@2 {
-			compatible = "pmbus-fan";
 			reg = <2>;
-			tach-pulses = <2>;
 		};
 
 		fan3: fan@3 {
-			compatible = "pmbus-fan";
 			reg = <3>;
-			tach-pulses = <2>;
 		};
 
 		fan4: fan@4 {
-			compatible = "pmbus-fan";
 			reg = <4>;
-			tach-pulses = <2>;
 		};
 
 		fan5: fan@5 {
-			compatible = "pmbus-fan";
 			reg = <5>;
-			tach-pulses = <2>;
 		};
 	};
 
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-tacoma.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-tacoma.dts
index b31eb8e58c6b4..6fe7023599e88 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-tacoma.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-tacoma.dts
@@ -481,55 +481,19 @@ max31785@52 {
 		#size-cells = <0>;
 
 		fan@0 {
-			compatible = "pmbus-fan";
 			reg = <0>;
-			tach-pulses = <2>;
-			maxim,fan-rotor-input = "tach";
-			maxim,fan-pwm-freq = <25000>;
-			maxim,fan-dual-tach;
-			maxim,fan-no-watchdog;
-			maxim,fan-no-fault-ramp;
-			maxim,fan-ramp = <2>;
-			maxim,fan-fault-pin-mon;
 		};
 
 		fan@1 {
-			compatible = "pmbus-fan";
 			reg = <1>;
-			tach-pulses = <2>;
-			maxim,fan-rotor-input = "tach";
-			maxim,fan-pwm-freq = <25000>;
-			maxim,fan-dual-tach;
-			maxim,fan-no-watchdog;
-			maxim,fan-no-fault-ramp;
-			maxim,fan-ramp = <2>;
-			maxim,fan-fault-pin-mon;
 		};
 
 		fan@2 {
-			compatible = "pmbus-fan";
 			reg = <2>;
-			tach-pulses = <2>;
-			maxim,fan-rotor-input = "tach";
-			maxim,fan-pwm-freq = <25000>;
-			maxim,fan-dual-tach;
-			maxim,fan-no-watchdog;
-			maxim,fan-no-fault-ramp;
-			maxim,fan-ramp = <2>;
-			maxim,fan-fault-pin-mon;
 		};
 
 		fan@3 {
-			compatible = "pmbus-fan";
 			reg = <3>;
-			tach-pulses = <2>;
-			maxim,fan-rotor-input = "tach";
-			maxim,fan-pwm-freq = <25000>;
-			maxim,fan-dual-tach;
-			maxim,fan-no-watchdog;
-			maxim,fan-no-fault-ramp;
-			maxim,fan-ramp = <2>;
-			maxim,fan-fault-pin-mon;
 		};
 	};
 
-- 
2.51.0

Re: [PATCH v7 RESEND 4/7] dt-bindings: hwmon: Move max31785 compatibles to max31790 document

[Guenter Roeck]

On 10/1/25 07:44, Eddie James wrote:
> The binding for the max31785 is the same as the max31790, so just add
> some compatible strings for the max31785 chip.
> 
> Signed-off-by: Eddie James <eajames@linux.ibm.com>
> Reviewed-by: Rob Herring (Arm) <robh@kernel.org>

I'll pick this and the next patch of the series after the commit window closes.

Guenter

Re: [PATCH v7 RESEND 4/7] dt-bindings: hwmon: Move max31785 compatibles to max31790 document

[Guenter Roeck]

On Wed, Oct 01, 2025 at 09:44:38AM -0500, Eddie James wrote:
> The binding for the max31785 is the same as the max31790, so just add
> some compatible strings for the max31785 chip.
> 
> Signed-off-by: Eddie James <eajames@linux.ibm.com>
> Reviewed-by: Rob Herring (Arm) <robh@kernel.org>

Applied to hwmon-next.

Thanks,
Guenter

Re: [PATCH v7 RESEND 5/7] dt-bindings: hwmon: max31790: Use addressed fan nodes

[Guenter Roeck]

On Wed, Oct 01, 2025 at 09:44:39AM -0500, Eddie James wrote:
> Since fan properties can include reg, the fan controller should be
> able to specify address-cells and size-cells properties and use
> an addressed fan child node.
> 
> Signed-off-by: Eddie James <eajames@linux.ibm.com>
> Reviewed-by: Rob Herring (Arm) <robh@kernel.org>

Applied.

Thanks,
Guenter

Re: [PATCH v7 RESEND 3/7] dt-bindings: iio: Add Infineon DPS310 sensor documentation

[Jonathan Cameron]

On Wed,  1 Oct 2025 09:44:37 -0500
Eddie James <eajames@linux.ibm.com> wrote:

> The DPS310 is a barometric pressure and temperature sensor with
> an I2C interface. Remove it from trivial-devices.yaml and add its
> own documentation.

Hi Eddie,

Why?  I guess you need the #io-channel-cells which trivial devices
doesn't allow because you have a consumer driver?

Obviously the binding patch shouldn't mention that, but it could call
out that there can be such consumers.

I'd also expect to see some supplies even if the driver doesn't yet
explicitly handle them.

Jonathan

> 
> Signed-off-by: Eddie James <eajames@linux.ibm.com>
> Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
> ---
>  .../iio/pressure/infineon,dps310.yaml         | 44 +++++++++++++++++++
>  .../devicetree/bindings/trivial-devices.yaml  |  2 -
>  MAINTAINERS                                   |  1 +
>  3 files changed, 45 insertions(+), 2 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/iio/pressure/infineon,dps310.yaml
> 
> diff --git a/Documentation/devicetree/bindings/iio/pressure/infineon,dps310.yaml b/Documentation/devicetree/bindings/iio/pressure/infineon,dps310.yaml
> new file mode 100644
> index 0000000000000..7c0782e2a821b
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/iio/pressure/infineon,dps310.yaml
> @@ -0,0 +1,44 @@
> +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/iio/pressure/infineon,dps310.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Infineon DPS310 barometric pressure and temperature sensor
> +
> +maintainers:
> +  - Eddie James <eajames@linux.ibm.com>
> +
> +description:
> +  The DPS310 is a barometric pressure and temperature sensor with an I2C
> +  interface.
> +
> +properties:
> +  compatible:
> +    enum:
> +      - infineon,dps310
> +
> +  reg:
> +    maxItems: 1
> +
> +  "#io-channel-cells":
> +    const: 0
> +
> +required:
> +  - compatible
> +  - reg
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    i2c {
> +        #address-cells = <1>;
> +        #size-cells = <0>;
> +
> +        pressure-sensor@76 {
> +          compatible = "infineon,dps310";
> +          reg = <0x76>;
> +          #io-channel-cells = <0>;
> +        };
> +    };
> diff --git a/Documentation/devicetree/bindings/trivial-devices.yaml b/Documentation/devicetree/bindings/trivial-devices.yaml
> index 7609acaa752d5..a72b7fabc7034 100644
> --- a/Documentation/devicetree/bindings/trivial-devices.yaml
> +++ b/Documentation/devicetree/bindings/trivial-devices.yaml
> @@ -127,8 +127,6 @@ properties:
>            - ibm,cffps2
>              # IBM On-Chip Controller hwmon device
>            - ibm,p8-occ-hwmon
> -            # Infineon barometric pressure and temperature sensor
> -          - infineon,dps310
>              # Infineon IR36021 digital POL buck controller
>            - infineon,ir36021
>              # Infineon IRPS5401 Voltage Regulator (PMIC)
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 0c8281ea4cc64..92b9854a0e07d 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -12191,6 +12191,7 @@ INFINEON DPS310 Driver
>  M:	Eddie James <eajames@linux.ibm.com>
>  L:	linux-iio@vger.kernel.org
>  S:	Maintained
> +F:	Documentation/devicetree/bindings/iio/pressure/infineon,dps310.yaml
>  F:	drivers/iio/pressure/dps310.c
>  
>  INFINEON PEB2466 ASoC CODEC

Re: [PATCH v7 RESEND 3/7] dt-bindings: iio: Add Infineon DPS310 sensor documentation

[Eddie James]

On 10/3/25 9:01 AM, Jonathan Cameron wrote:
> On Wed,  1 Oct 2025 09:44:37 -0500
> Eddie James <eajames@linux.ibm.com> wrote:
>
>> The DPS310 is a barometric pressure and temperature sensor with
>> an I2C interface. Remove it from trivial-devices.yaml and add its
>> own documentation.
> Hi Eddie,
>
> Why?  I guess you need the #io-channel-cells which trivial devices
> doesn't allow because you have a consumer driver?


Correct.


>
> Obviously the binding patch shouldn't mention that, but it could call
> out that there can be such consumers.


OK, I can add that.


>
> I'd also expect to see some supplies even if the driver doesn't yet
> explicitly handle them.


You mean in the example section? Sure. I'll send a patch separately 
since the rest is merged


Thanks,

Eddie


>
> Jonathan
>
>> Signed-off-by: Eddie James <eajames@linux.ibm.com>
>> Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
>> ---
>>   .../iio/pressure/infineon,dps310.yaml         | 44 +++++++++++++++++++
>>   .../devicetree/bindings/trivial-devices.yaml  |  2 -
>>   MAINTAINERS                                   |  1 +
>>   3 files changed, 45 insertions(+), 2 deletions(-)
>>   create mode 100644 Documentation/devicetree/bindings/iio/pressure/infineon,dps310.yaml
>>
>> diff --git a/Documentation/devicetree/bindings/iio/pressure/infineon,dps310.yaml b/Documentation/devicetree/bindings/iio/pressure/infineon,dps310.yaml
>> new file mode 100644
>> index 0000000000000..7c0782e2a821b
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/iio/pressure/infineon,dps310.yaml
>> @@ -0,0 +1,44 @@
>> +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/iio/pressure/infineon,dps310.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: Infineon DPS310 barometric pressure and temperature sensor
>> +
>> +maintainers:
>> +  - Eddie James <eajames@linux.ibm.com>
>> +
>> +description:
>> +  The DPS310 is a barometric pressure and temperature sensor with an I2C
>> +  interface.
>> +
>> +properties:
>> +  compatible:
>> +    enum:
>> +      - infineon,dps310
>> +
>> +  reg:
>> +    maxItems: 1
>> +
>> +  "#io-channel-cells":
>> +    const: 0
>> +
>> +required:
>> +  - compatible
>> +  - reg
>> +
>> +additionalProperties: false
>> +
>> +examples:
>> +  - |
>> +    i2c {
>> +        #address-cells = <1>;
>> +        #size-cells = <0>;
>> +
>> +        pressure-sensor@76 {
>> +          compatible = "infineon,dps310";
>> +          reg = <0x76>;
>> +          #io-channel-cells = <0>;
>> +        };
>> +    };
>> diff --git a/Documentation/devicetree/bindings/trivial-devices.yaml b/Documentation/devicetree/bindings/trivial-devices.yaml
>> index 7609acaa752d5..a72b7fabc7034 100644
>> --- a/Documentation/devicetree/bindings/trivial-devices.yaml
>> +++ b/Documentation/devicetree/bindings/trivial-devices.yaml
>> @@ -127,8 +127,6 @@ properties:
>>             - ibm,cffps2
>>               # IBM On-Chip Controller hwmon device
>>             - ibm,p8-occ-hwmon
>> -            # Infineon barometric pressure and temperature sensor
>> -          - infineon,dps310
>>               # Infineon IR36021 digital POL buck controller
>>             - infineon,ir36021
>>               # Infineon IRPS5401 Voltage Regulator (PMIC)
>> diff --git a/MAINTAINERS b/MAINTAINERS
>> index 0c8281ea4cc64..92b9854a0e07d 100644
>> --- a/MAINTAINERS
>> +++ b/MAINTAINERS
>> @@ -12191,6 +12191,7 @@ INFINEON DPS310 Driver
>>   M:	Eddie James <eajames@linux.ibm.com>
>>   L:	linux-iio@vger.kernel.org
>>   S:	Maintained
>> +F:	Documentation/devicetree/bindings/iio/pressure/infineon,dps310.yaml
>>   F:	drivers/iio/pressure/dps310.c
>>   
>>   INFINEON PEB2466 ASoC CODEC
>

Re: [PATCH v7 RESEND 3/7] dt-bindings: iio: Add Infineon DPS310 sensor documentation

[Jonathan Cameron]

On Mon, 6 Oct 2025 08:44:55 -0500
Eddie James <eajames@linux.ibm.com> wrote:

> On 10/3/25 9:01 AM, Jonathan Cameron wrote:
> > On Wed,  1 Oct 2025 09:44:37 -0500
> > Eddie James <eajames@linux.ibm.com> wrote:
> >  
> >> The DPS310 is a barometric pressure and temperature sensor with
> >> an I2C interface. Remove it from trivial-devices.yaml and add its
> >> own documentation.  
> > Hi Eddie,
> >
> > Why?  I guess you need the #io-channel-cells which trivial devices
> > doesn't allow because you have a consumer driver?  
> 
> 
> Correct.
> 
> 
> >
> > Obviously the binding patch shouldn't mention that, but it could call
> > out that there can be such consumers.  
> 
> 
> OK, I can add that.
> 
> 
> >
> > I'd also expect to see some supplies even if the driver doesn't yet
> > explicitly handle them.  
> 
> 
> You mean in the example section? Sure. I'll send a patch separately 
> since the rest is merged

Supplies need listing as actual properties (+ in the example)
From a binding point of view they are 'required' if the power needs
to be turned on for the chip to work.  On actual DT files they might
not be there if a fixed supply is in use and someone didn't other providing
it. In those cases the regulator code provides a fake regulator to make
everything work.

> 
> 
> Thanks,
> 
> Eddie
> 
> 
> >
> > Jonathan
> >  
> >> Signed-off-by: Eddie James <eajames@linux.ibm.com>
> >> Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
> >> ---
> >>   .../iio/pressure/infineon,dps310.yaml         | 44 +++++++++++++++++++
> >>   .../devicetree/bindings/trivial-devices.yaml  |  2 -
> >>   MAINTAINERS                                   |  1 +
> >>   3 files changed, 45 insertions(+), 2 deletions(-)
> >>   create mode 100644 Documentation/devicetree/bindings/iio/pressure/infineon,dps310.yaml
> >>
> >> diff --git a/Documentation/devicetree/bindings/iio/pressure/infineon,dps310.yaml b/Documentation/devicetree/bindings/iio/pressure/infineon,dps310.yaml
> >> new file mode 100644
> >> index 0000000000000..7c0782e2a821b
> >> --- /dev/null
> >> +++ b/Documentation/devicetree/bindings/iio/pressure/infineon,dps310.yaml
> >> @@ -0,0 +1,44 @@
> >> +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
> >> +%YAML 1.2
> >> +---
> >> +$id: http://devicetree.org/schemas/iio/pressure/infineon,dps310.yaml#
> >> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> >> +
> >> +title: Infineon DPS310 barometric pressure and temperature sensor
> >> +
> >> +maintainers:
> >> +  - Eddie James <eajames@linux.ibm.com>
> >> +
> >> +description:
> >> +  The DPS310 is a barometric pressure and temperature sensor with an I2C
> >> +  interface.
> >> +
> >> +properties:
> >> +  compatible:
> >> +    enum:
> >> +      - infineon,dps310
> >> +
> >> +  reg:
> >> +    maxItems: 1
> >> +
> >> +  "#io-channel-cells":
> >> +    const: 0
> >> +
> >> +required:
> >> +  - compatible
> >> +  - reg
> >> +
> >> +additionalProperties: false
> >> +
> >> +examples:
> >> +  - |
> >> +    i2c {
> >> +        #address-cells = <1>;
> >> +        #size-cells = <0>;
> >> +
> >> +        pressure-sensor@76 {
> >> +          compatible = "infineon,dps310";
> >> +          reg = <0x76>;
> >> +          #io-channel-cells = <0>;
> >> +        };
> >> +    };
> >> diff --git a/Documentation/devicetree/bindings/trivial-devices.yaml b/Documentation/devicetree/bindings/trivial-devices.yaml
> >> index 7609acaa752d5..a72b7fabc7034 100644
> >> --- a/Documentation/devicetree/bindings/trivial-devices.yaml
> >> +++ b/Documentation/devicetree/bindings/trivial-devices.yaml
> >> @@ -127,8 +127,6 @@ properties:
> >>             - ibm,cffps2
> >>               # IBM On-Chip Controller hwmon device
> >>             - ibm,p8-occ-hwmon
> >> -            # Infineon barometric pressure and temperature sensor
> >> -          - infineon,dps310
> >>               # Infineon IR36021 digital POL buck controller
> >>             - infineon,ir36021
> >>               # Infineon IRPS5401 Voltage Regulator (PMIC)
> >> diff --git a/MAINTAINERS b/MAINTAINERS
> >> index 0c8281ea4cc64..92b9854a0e07d 100644
> >> --- a/MAINTAINERS
> >> +++ b/MAINTAINERS
> >> @@ -12191,6 +12191,7 @@ INFINEON DPS310 Driver
> >>   M:	Eddie James <eajames@linux.ibm.com>
> >>   L:	linux-iio@vger.kernel.org
> >>   S:	Maintained
> >> +F:	Documentation/devicetree/bindings/iio/pressure/infineon,dps310.yaml
> >>   F:	drivers/iio/pressure/dps310.c
> >>   
> >>   INFINEON PEB2466 ASoC CODEC  
> >