From: hehuan1@eswincomputing.com
To: ulf.hansson@linaro.org, robh@kernel.org, krzk+dt@kernel.org,
conor+dt@kernel.org, jszhang@kernel.org, adrian.hunter@intel.com,
p.zabel@pengutronix.de, linux-mmc@vger.kernel.org,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org
Cc: ningyu@eswincomputing.com, linmin@eswincomputing.com,
pinkesh.vaghela@einfochips.com, xuxiang@eswincomputing.com,
luyulin@eswincomputing.com, dongxuyang@eswincomputing.com,
zhangsenchuan@eswincomputing.com,
weishangjuan@eswincomputing.com, lizhi2@eswincomputing.com,
caohang@eswincomputing.com, hehuan1@eswincomputing.com
Subject: [PATCH v3 1/2] dt-bindings: mmc: sdhci-of-dwcmshc: Add Eswin EIC7700
Date: Fri, 10 Oct 2025 17:40:13 +0800 [thread overview]
Message-ID: <20251010094014.1596-1-hehuan1@eswincomputing.com> (raw)
In-Reply-To: <20251010093807.1579-1-hehuan1@eswincomputing.com>
From: Huan He <hehuan1@eswincomputing.com>
EIC7700 use Synopsys dwcmshc IP for SD/eMMC controllers.
Add Eswin EIC7700 support in sdhci-of-dwcmshc.yaml.
Signed-off-by: Huan He <hehuan1@eswincomputing.com>
---
.../bindings/mmc/snps,dwcmshc-sdhci.yaml | 57 +++++++++++++++++--
1 file changed, 51 insertions(+), 6 deletions(-)
diff --git a/Documentation/devicetree/bindings/mmc/snps,dwcmshc-sdhci.yaml b/Documentation/devicetree/bindings/mmc/snps,dwcmshc-sdhci.yaml
index f882219a0a26..48661502a5a3 100644
--- a/Documentation/devicetree/bindings/mmc/snps,dwcmshc-sdhci.yaml
+++ b/Documentation/devicetree/bindings/mmc/snps,dwcmshc-sdhci.yaml
@@ -30,6 +30,7 @@ properties:
- sophgo,sg2002-dwcmshc
- sophgo,sg2042-dwcmshc
- thead,th1520-dwcmshc
+ - eswin,eic7700-dwcmshc
reg:
maxItems: 1
@@ -52,17 +53,30 @@ properties:
maxItems: 5
reset-names:
- items:
- - const: core
- - const: bus
- - const: axi
- - const: block
- - const: timer
+ maxItems: 5
rockchip,txclk-tapnum:
description: Specify the number of delay for tx sampling.
$ref: /schemas/types.yaml#/definitions/uint8
+ eswin,hsp-sp-csr:
+ $ref: /schemas/types.yaml#/definitions/phandle-array
+ items:
+ - description: Phandle to HSP(High-Speed Peripheral) device
+ - description: Offset of the stability status register for
+ internal clock
+ - description: Offset of the stability register for host regulator
+ voltage.
+ description: |
+ HSP CSR is to control and get status of different high-speed
+ peripherals (such as Ethernet, USB, SATA, etc.) via register,
+ which can close module's clock, reset module independently
+ and tune board-level's parameters of PHY, etc.
+
+ eswin,drive-impedance-ohms:
+ description: Specifies the drive impedance in Ohm.
+ enum: [33, 40, 50, 66, 100]
+
required:
- compatible
- reg
@@ -110,6 +124,37 @@ allOf:
- const: block
- const: timer
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: eswin,eic7700-dwcmshc
+ then:
+ properties:
+ resets:
+ minItems: 4
+ maxItems: 4
+ reset-names:
+ items:
+ - const: axi
+ - const: phy
+ - const: prstn
+ - const: txrx
+ required:
+ - eswin,hsp-sp-csr
+ - eswin,drive-impedance-ohms
+ else:
+ properties:
+ resets:
+ maxItems: 5
+ reset-names:
+ items:
+ - const: core
+ - const: bus
+ - const: axi
+ - const: block
+ - const: timer
+
- if:
properties:
compatible:
--
2.25.1
next prev parent reply other threads:[~2025-10-10 9:40 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-10-10 9:38 [PATCH v3 0/2] Add support for Eswin EIC7700 SD/eMMC controller hehuan1
2025-10-10 9:40 ` hehuan1 [this message]
2025-10-10 14:33 ` [PATCH v3 1/2] dt-bindings: mmc: sdhci-of-dwcmshc: Add Eswin EIC7700 Conor Dooley
2025-10-10 9:41 ` [PATCH v3 2/2] mmc: sdhci-of-dwcmshc: Add support for " hehuan1
2025-10-11 0:39 ` kernel test robot
2025-10-11 1:54 ` kernel test robot
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20251010094014.1596-1-hehuan1@eswincomputing.com \
--to=hehuan1@eswincomputing.com \
--cc=adrian.hunter@intel.com \
--cc=caohang@eswincomputing.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=dongxuyang@eswincomputing.com \
--cc=jszhang@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linmin@eswincomputing.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mmc@vger.kernel.org \
--cc=lizhi2@eswincomputing.com \
--cc=luyulin@eswincomputing.com \
--cc=ningyu@eswincomputing.com \
--cc=p.zabel@pengutronix.de \
--cc=pinkesh.vaghela@einfochips.com \
--cc=robh@kernel.org \
--cc=ulf.hansson@linaro.org \
--cc=weishangjuan@eswincomputing.com \
--cc=xuxiang@eswincomputing.com \
--cc=zhangsenchuan@eswincomputing.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).