From: Richard Genoud <richard.genoud@bootlin.com>
To: Miquel Raynal <miquel.raynal@bootlin.com>,
Richard Weinberger <richard@nod.at>,
Vignesh Raghavendra <vigneshr@ti.com>,
Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>, Chen-Yu Tsai <wens@csie.org>,
Jernej Skrabec <jernej.skrabec@gmail.com>,
Samuel Holland <samuel@sholland.org>
Cc: "Uwe Kleine-König" <u.kleine-koenig@baylibre.com>,
"Wentao Liang" <vulab@iscas.ac.cn>,
"Johan Hovold" <johan@kernel.org>,
"Maxime Ripard" <mripard@kernel.org>,
"Thomas Petazzoni" <thomas.petazzoni@bootlin.com>,
linux-mtd@lists.infradead.org, devicetree@vger.kernel.org,
linux-arm-kernel@lists.infradead.org,
linux-sunxi@lists.linux.dev, linux-kernel@vger.kernel.org,
"Richard Genoud" <richard.genoud@bootlin.com>
Subject: [PATCH v2 01/15] mtd: rawnand: sunxi: Remove superfluous register readings
Date: Mon, 13 Oct 2025 17:26:31 +0200 [thread overview]
Message-ID: <20251013152645.1119308-2-richard.genoud@bootlin.com> (raw)
In-Reply-To: <20251013152645.1119308-1-richard.genoud@bootlin.com>
The register NFC_REG_ECC_CTL was read twice and the result was not used,
then a third time with a mask applied.
Removing those calls didn't change the behavior.
Tested on H616 SoC, scrambling enabled.
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Richard Genoud <richard.genoud@bootlin.com>
---
drivers/mtd/nand/raw/sunxi_nand.c | 3 +--
1 file changed, 1 insertion(+), 2 deletions(-)
diff --git a/drivers/mtd/nand/raw/sunxi_nand.c b/drivers/mtd/nand/raw/sunxi_nand.c
index f6a8e8ae819d..cb12179b63a5 100644
--- a/drivers/mtd/nand/raw/sunxi_nand.c
+++ b/drivers/mtd/nand/raw/sunxi_nand.c
@@ -623,13 +623,12 @@ static void sunxi_nfc_randomizer_config(struct nand_chip *nand, int page,
bool ecc)
{
struct sunxi_nfc *nfc = to_sunxi_nfc(nand->controller);
- u32 ecc_ctl = readl(nfc->regs + NFC_REG_ECC_CTL);
+ u32 ecc_ctl;
u16 state;
if (!(nand->options & NAND_NEED_SCRAMBLING))
return;
- ecc_ctl = readl(nfc->regs + NFC_REG_ECC_CTL);
state = sunxi_nfc_randomizer_state(nand, page, ecc);
ecc_ctl = readl(nfc->regs + NFC_REG_ECC_CTL) & ~NFC_RANDOM_SEED_MSK;
writel(ecc_ctl | NFC_RANDOM_SEED(state), nfc->regs + NFC_REG_ECC_CTL);
next prev parent reply other threads:[~2025-10-13 15:27 UTC|newest]
Thread overview: 21+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-10-13 15:26 [PATCH v2 00/15] Introduce Allwinner H6/H616 NAND controller support Richard Genoud
2025-10-13 15:26 ` Richard Genoud [this message]
2025-10-13 15:26 ` [PATCH v2 02/15] mtd: rawnand: sunxi: move ECC strenghts in sunxi_nfc_caps Richard Genoud
2025-10-13 15:54 ` Chen-Yu Tsai
2025-10-13 15:26 ` [PATCH v2 03/15] mtd: rawnand: sunxi: introduce reg_ecc_err_cnt " Richard Genoud
2025-10-13 15:26 ` [PATCH v2 04/15] mtd: rawnand: sunxi: introduce reg_user_data " Richard Genoud
2025-10-13 15:26 ` [PATCH v2 05/15] mtd: rawnand: sunxi: rework pattern found registers Richard Genoud
2025-10-13 15:26 ` [PATCH v2 06/15] mtd: rawnand: sunxi: add has_ecc_block_512 capability Richard Genoud
2025-10-13 15:26 ` [PATCH v2 07/15] mtd: rawnand: sunxi: introduce ecc_mode_mask in sunxi_nfc_caps Richard Genoud
2025-10-13 15:26 ` [PATCH v2 08/15] mtd: rawnand: sunxi: introduce random en/dir " Richard Genoud
2025-10-13 15:26 ` [PATCH v2 09/15] mtd: rawnand: sunxi: introduce reg_pat_id " Richard Genoud
2025-10-13 15:26 ` [PATCH v2 10/15] mtd: rawnand: sunxi: introduce reg_spare_area " Richard Genoud
2025-10-13 15:26 ` [PATCH v2 11/15] mtd: rawnand: sunxi: introduce ecc_err_mask " Richard Genoud
2025-10-13 15:26 ` [PATCH v2 12/15] mtd: rawnand: sunxi: introduce sram_size " Richard Genoud
2025-10-13 15:26 ` [PATCH v2 13/15] mtd: rawnand: sunxi: Add support for H616 nand controller Richard Genoud
2025-10-13 15:26 ` [PATCH v2 14/15] dt-bindings: mtd: sunxi: Add H616 compatible Richard Genoud
2025-10-13 19:44 ` Conor Dooley
2025-10-14 7:13 ` Richard GENOUD
2025-10-13 15:26 ` [PATCH v2 15/15] arm64: dts: allwinner: h616: add NAND controller Richard Genoud
2025-10-13 15:43 ` Jernej Škrabec
2025-10-13 15:59 ` Richard GENOUD
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20251013152645.1119308-2-richard.genoud@bootlin.com \
--to=richard.genoud@bootlin.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=jernej.skrabec@gmail.com \
--cc=johan@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mtd@lists.infradead.org \
--cc=linux-sunxi@lists.linux.dev \
--cc=miquel.raynal@bootlin.com \
--cc=mripard@kernel.org \
--cc=richard@nod.at \
--cc=robh@kernel.org \
--cc=samuel@sholland.org \
--cc=thomas.petazzoni@bootlin.com \
--cc=u.kleine-koenig@baylibre.com \
--cc=vigneshr@ti.com \
--cc=vulab@iscas.ac.cn \
--cc=wens@csie.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).